Variable Data Rates Research Articles

Performance Analysis of IEEE 802.15.6 CSMA/CA Protocol for WBAN Medical Scenario through DTMC Model.

The newly drafted IEEE 802.15.6 standard for Wireless Body Area Networks (WBAN) has been concentrating on a numerous medical and non-medical applications. Such short range wireless communication standard offers ultra-low power consumption with variable data rates from few Kbps to Mbps in, on or around the proximity of the human body. In this paper, the performance analysis of carrier sense multiple access with collision avoidance (CSMA/CA) scheme based on IEEE 802.15.6 standard in terms of throughput, reliability, clear channel assessment (CCA) failure probability, packet drop probability, and end-to-end delay has been presented. We have developed a discrete-time Markov chain (DTMC) to significantly evaluate the performances of IEEE 802.15.6 CSMA/CA under non-ideal channel condition having saturated traffic condition including node wait time and service time. We also visualize that, as soon as the payload length increases the CCA failure probability increases, which results in lower node's reliability. Also, we have calculated the end-to-end delay in order to prioritize the node wait time cause by backoff and retransmission. The user priority (UP) wise DTMC analysis has been performed to show the importance of the standard especially for medical scenario.

Design and Performance Investigation for the Optical Combinational Networks at High Data Rate

Abstract This article explores performance study for optical combinational designs based on nonlinear characteristics with semiconductor optical amplifier (SOA). Two configurations for optical half-adder with non-return-to-zero modulation pattern altogether with Mach–Zehnder modulator, interferometer at 50-Gbps data rate have been successfully realized. Accordingly, SUM and CARRY outputs have been concurrently executed and verified for their output waveforms. Numerical simulations for variation of data rate and key design parameters have been effectively executed outcome with optimum performance. Investigations depict overall good performance of the design in terms of the extinction factor. It also inferred that all-optical realization based on SOA is competent scheme, as it circumvents costly optoelectronic translation. This could be well supportive to erect larger complex optical combinational circuits.

DFC++ Processing Framework Concept

Development of modern Software Defined Radio (SDR) based communication systems can be accelerated significantly by the use of processing frameworks. The evolution of SDR and the involved departure from digital representations of classical radio architecture towards more abstract software systems raises new requirements of increased flexibility and versatility. The proposed Data Flow Control for C++ (DFC++) processing framework concept addresses those requirements by employing modern programming techniques and flow control mechanisms to allow for variable data rates, dynamic paths, and flexible component designs. Another important trend is the integration of various embedded platforms in the software radio domain. The rapidly increasing performance and efficiency of embedded processors enables the deployment of SDR systems in more space and power constrained environments. Therefore covering a heterogeneous hardware selection becomes increasingly important for processing frameworks. By relying exclusively on C++ and minimizing external dependencies, DFC++ is specifically aiming for excellent portability and adaptability to support a wide range of current and future software radio projects while maintaining high performance and ease of use. This paper introduces the key aspects of the DFC++ concept and implementation with focus on the reference pointer based data transport mechanisms responsible for the propagation of user data between different processing components.

Optimal Bandwidth Reservation for Video Streaming in DiffServ Domain

With the emergency of more and more video applications, the problem of providing differentiated Quality of Service (QoS) for various kinds of streams should be solved. DiffServ was proposed to balance transmission guarantee of video and data streams. Existing studies focused on the promotion of video receiving quality by allocating excess resources. In this paper we propose an optimal bandwidth reservation mechanism, aiming at proper amount of bandwidth reservation and good video transmission performance. This mechanism tries to find a moderate reservation according to the video characteristics and buffer size of forwarding routers. Various video sequences and different buffer sizes are employed in the performance evaluation experiments and simulation results verify that (1) Proposed mechanism show its adaptability to data rate, data rate variation and continuous burst of the streaming video. (2) Proposed mechanism presents good performance under various buffer sizes. (3) The amount of bandwidth reservation, which is determined by the streaming video and buffer size of forwarding routers, is moderate to ensure video receiving quality.

Full-Duplex Airborne Ultrasonic Data Communication Using a Pilot-Aided QAM-OFDM Modulation Scheme.

Orthogonal frequency division multiplexing (OFDM) has been extensively used in a variety of broadband digital wireless communications applications because of its high bandwidth utilization efficiency and effective immunity to multipath distortion. This paper has investigated quadrature amplitude modulation and OFDM methods in air-coupled ultrasonic communication, using broadband capacitive ultrasonic transducers with high- k dielectric layers. OFDM phase noise was discussed and corrected using a pilot-aided estimation algorithm. The overall system data rate achieved was up to 400 kb/s with a spectral efficiency of 2 b/s/Hz. An ultrasonic propagation model for signal prediction considered atmospheric absorption of sound in air, beam divergence, and transducer frequency response. The simulations were compared with the experimental results, and good agreement was found between the two. Two-way communication through air was also implemented successfully by applying three-way handshaking initialization and an adaptive modulation scheme with variable data rates depending on the transmission distance, estimated using received signal strength indication measurement. It was shown that the error-free transmission range could be extended up to 2.5 m using different system transfer rates from 400 kb/s down to 100 kb/s. In full-duplex transmission mode, the overall error-free system data rate achieved was 0.8 Mb/s up to 1.5 m.

Efficient Routing and Spectrum Allocation Considering QoT in Elastic Optical Network

In recent years, Orthogonal Frequency Division Multiplexing (OFDM)-based elastic optical network (EON) has drawn increasing attention in both academia and industry. Compared to traditional optical Wavelength Division Multiplexing (WDM) network, EON is capable of supporting variable data rate, accommodating traffic demands flexibly with finer provisioning granularity, and utilizing spectrum more efficiently. Accordingly, the resource management in EON is different from that in WDM networks and addresses new challenges in network design and control. In this paper, we study the routing, modulation level and spectrum allocation (RMLSA) problem in EON. We propose an efficient link-based mixed integer linear programming (MILP) model with the objective to optimally utilize the spectrum resources while considering the constraint on Quality of Transmission (QoT). Then, the performance of the proposed model is evaluated and analyzed through case study.

Multichannel Ultrasonic Data Communications in Air Using Range-Dependent Modulation Schemes.

There are several well-developed technologies of wireless communication such as radio frequency (RF) and infrared (IR), but ultrasonic methods can be a good alternative in some situations. A multichannel airborne ultrasonic data communication system is described in this paper. ON-OFF keying (OOK) and binary phase-shift keying (BPSK) modulation schemes were implemented successfully in the system by using a pair of commercially available capacitive ultrasonic transducers in a relatively low multipath indoor laboratory environment. Six channels were used from 50 to 110 kHz with a channel spacing of 12 kHz, allowing multiple 8-bit data packets to be transmitted simultaneously. The system data transfer rate achieved was up to 60 kb/s and ultrasonic wireless synchronization was implemented instead of using a hard-wired link. A model developed in the work could accurately predict ultrasonic signals through the air channels. Signal root mean square (rms) values and system bit error rates (BERs) were analyzed over different distances. Error-free decoding was achieved over ranges up to 5 m using a multichannel OOK modulation scheme. To obtain the highest data transfer rate and the longest error-free transmission distance, a range-dependent multichannel scheme with variable data rates, channel frequencies, and different modulation schemes, was also studied in the work. Within 2 m, error-free transmission was achieved using a five-channel OOK with a data rate of 63 kb/s. Between 2 and 5 m, six-channel OOK with 60 kb/s data transfer rate was error free. Beyond 5 m, the error-free transmission range could be extended up to 10 m using three-channel BPSK with a reduced data rate of 30 kb/s. The situation when two transducers were misaligned using three-channel OOK and BPSK schemes was also investigated in the work. It was concluded that error-free transmission could still be achieved with a lateral displacement of less than 7% and oblique angles of less than 7°, and three-channel BPSK proved to be more robust than three-channel OOK with transducer misalignment.

Decimation Chain Modeling for Dual-Band Radio Receiver and Its Operation for Continuous Packet Connectivity

A decimation chain for multi-standard reconfigurable radios is presented for 900-MHz and 1,900-MHz dual-band cellular standards with a data interpolator based on the Lagrange method for adjusting the variable data rate to a fixed data rate appropriate for each standard. The two proposed configurations are analyzed and compared to provide insight into aliasing and the signal bandwidth by means of a newly introduced measure called interpolation error. The average interpolation error is reduced as the ratio of the sampling frequency to the signal BW is increased. The decimation chain and the multi-rate analog-to-digital converter are simulated to compute the interpolation error and the output signal-to-noise ratio. Further, a method to operate the above-mentioned chain under a compressed mode of operation is proposed in order to guarantee continuous packet connectivity for inter-radio-access technologies. The presented decimation chain can be applied to LTE, WCDMA, GSM multi-mode multi-band digital front-end which will ultimately lead to the software-defined radio.

A Robust CDMA VLC System Against Front-End Nonlinearity

The nonlinearity of a light-emitting diode (LED) limits the system performance of a visible light communications (VLC) system. Many nonlinearity mitigation methods have been studied. Recent technology advances in the micro-LED array have provided a simple alternative to deal with the system nonlinearity. In this paper, we study the approach of providing multiple access for the VLC system with the micro-LED array. A code-division multiple-access (CDMA) scheme that enables multiple access with variable data rate is proposed. In addition, the proposed system architecture is immune to the nonlinearity of the micro-LED array, thus providing optimal system performance. Simulations and laboratory experiments show the robustness and consistency of the proposed scheme.

Scheduling in Wireless Networks with Rayleigh-Fading Interference

We study approximation algorithms for optimization of wireless spectrum access with n communication requests when interference conditions are given by the Rayleigh-fading model. This model extends the deterministic interference model based on the signal-to-interference-plus-noise ratio (SINR) using stochastic propagation to address fading effects observed in reality. We consider worst-case approximation guarantees for the two standard problems of capacity maximization and latency minimization. Our main result is a generic reduction of Rayleigh fading to the deterministic non-fading model. It allows to apply existing algorithms for the non-fading model in the Rayleigh-fading scenario while losing only a factor of O(log* n) in the approximation guarantee. This way, we obtain the first approximation guarantees for Rayleigh fading and, more fundamentally, show that non-trivial stochastic fading effects can be successfully handled using existing and future techniques for the non-fading model. We generalize these results in two ways. First, the same results apply for capacity maximization with variable data rates, when links obtain (non-binary) utility depending on the achieved SINR. Second, for binary utilities, we use a more detailed argument to obtain similar results even for distributed and game-theoretic approaches. Our analytical treatment is supported by simulations illustrating the performance of regret learning and, more generally, the relationship between both models.

Scalable Control Architecture for Variable-Rate Turn Compensation

The objective of this study was to determine if a CAN bus could be used to implement variable-rate turn compensation in a manner that is scalable by encoding application rates for an entire implement into a single data message. A variable-rate turn compensation test fixture was developed that used a CAN bus to communicate application rates to 16 individual nodes using a 2-byte data message (80-bit extended identifier CAN messages). The system assumed that the physical structure of an implement was linear and that the control nodes were equally spaced. Application rates for the outer-most nodes were broadcasted and the remaining nodes calculated their application rate using a linear interpolation method. Node locations were determined using a 4-bit binary thumbwheel switch located at each control node, allowing all nodes to run an identical program. Servo-controlled gauges were used to visualize node application rate across the test fixture. A joystick interface was developed to simulate vehicle movements and desired application rates. The system transmitted Bluetooth serial messages at a rate of 20 Hz, which were received by the test fixture and converted to CAN messages before being broadcasted to the control nodes. Two USB to CAN interfaces were connected to the CAN bus to insert additional traffic and measure bandwidth utilization. Due to the minimal amount of bandwidth required (<1%) to transmit variable-rate control messages, the system functioned properly when the CAN bus was heavily loaded with traffic up to 99% of the available bandwidth of 250 kbps. The variable-rate turn compensation test fixture demonstrated that a CAN bus is a suitable protocol for communicating variable-rate data. The scalable encoding technique developed in this study resulted in a single message required to update all nodes, regardless of the number of nodes in the system. The system has broad applicability in future planting, fertilizing, and chemical application systems where deposition points are evenly spaced along an implement.

Reactive Resource Provisioning Heuristics for Dynamic Dataflows on Cloud Infrastructure

The need for low latency analysis over high-velocity data streams motivates the need for distributed continuous dataflow systems. Contemporary stream processing systems use simple techniques to scale on elastic cloud resources to handle variable data rates. However, application QoS is also impacted by variability in resource performance exhibited by clouds and hence necessitates autonomic methods of provisioning elastic resources to support such applications on cloud infrastructure. We develop the concept of “dynamic dataflows” which utilize alternate tasks as additional control over the dataflow’s cost and QoS. Further, we formalize an optimization problem to represent deployment and runtime resource provisioning that allows us to balance the application’s QoS , value , and the resource cost . We propose two greedy heuristics, centralized and sharded , based on the variable-sized bin packing algorithm and compare against a Genetic Algorithm (GA) based heuristic that gives a near-optimal solution. A large-scale simulation study, using the linear road benchmark and VM performance traces from the AWS public cloud, shows that while GA-based heuristic provides a better quality schedule, the greedy heuristics are more practical, and can intelligently utilize cloud elasticity to mitigate the effect of variability, both in input data rates and cloud resource performance, to meet the QoS of fast data applications.

Analysis and Design of a Power-Scalable Continuous-Time FIR Equalizer for 10 Gb/s to 25 Gb/s Multi-Mode Fiber EDC in 28 nm LP CMOS

A continuous-time 7-tap FIR equalizer tailored to dispersion compensation in multi-mode fiber links is presented. By using a novel active delay line, the ultra-compact equalizer is very flexible, maintaining optimal performances and power scalability over a wide range of input data-rates. Particular care is taken to address critical issues of continuous-time realizations, such as noise, linearity and dynamic range. All-pass stages, realized with a simple circuit topology featuring high linearity and wide bandwidth, are investigated to implement the active delay line elements. Filter tap coefficients are realized with programmable transconductors and output currents are summed through a transimpedance amplifier, providing simultaneously high gain and wide bandwidth. Extensive experimental results, carried out on test chips realized in 28 nm LP CMOS technology, are presented. The equalizer demonstrates successful operation with variable data-rates ranging from 10 Gb/s to 25 Gb/s and power dissipation scalable from 55 mW to 90 mW. Compared to previously reported high-speed FIR equalizers, the proposed solution accepts the largest variation of the input data-rate with state-of-the-art power efficiency and core silicon area of only 0.085 mm 2 , meeting the demand of emerging 400 Gb/s standards.

개선된 LR-WPAN 시스템을 위한 시간 동기부 설계

최근 다양한 센서를 활용하는 응용분야의 증가로, 가변전송률을 지원하는 무선 통신 시스템의 필요성이 증가하고 있다. 이를 위해 2.45 GHz 주파수 대역을 사용하는 IEEE 802.15.4 LR-WPAN 시스템이 보편적으로 활용되고 있으나, LR-WPAN 시스템은 250 kbps의 단일 전송률만을 지원하고 있어 다양한 센서 네트워크 시스템에 응용되기에는 한계가 존재한다. 따라서, 본 논문에서는 31.25 kbps, 62.5 kbps, 125 kbps의 가변 전송률을 지원할 수 있는 프리앰블 구조를 정의하고, 주파수 오프셋에 강인한 이중 상관알고리즘을 기반으로 저복잡도 특성을 갖는 시간 동기부의 하드웨어 구조를 설계하였다. 제안된 시간 동기부는 18.36 K의 logic slices 및 4개의 DSP48s로 합성되었으며, 기존의 구조 대비 각각 79.1%와 99.4%의 감소를 보였다. Recently, with the growth of various sensor applications, the need of wireless communication systems which can support variable data rate is increasing. IEEE 802.15.4 LR-WPAN system using 2.45 GHz frequency band is very popular for the sensor applications. However, since LR-WPAN only supports the data rate of 250 kbps, it has a limit to be applied to various sensor networks. Therefore, we define the preamble structure which can support the data rates of 31.25 kbps, 62.5 kbps, 125 kbps, and present the low-complexity hardware architecture for time synchronizer based on double-correlation algorithm which can resist the CFO (carrier frequency offset). Implementation results show that the proposed time synchronizer include the logic slice of 18.36 K and four DSP48s, which are reduced at the rate of 79.1% and 99.4%, respectively, compared with existing architecture.

Work-Conserving In-Sequence Striping in Multi-Band Wireless Backhaul Systems

Link aggregation, or multi-band striping, has been used in wireless backhaul systems to overcome the limitations of bandwidth and transmission range. Work-conserving and in-sequence delivery are essential but conflicting requirements in multi-band striping systems. Previous schemes can achieve one or the other, but not both. The heterogeneous channel and time varying data rate in multi-band wireless backhaul systems present additional challenges. We aim at designing a multi-band striping algorithm to achieve both work-conserving and in-sequence delivery in the heterogeneous time-varying multi-band wireless backhaul system. We propose a parallel processing architecture for multi-band aggregation, and derive the necessary conditions for such system to achieve sequence preserving and work conserving. An optimum set of timing controls is developed and proved to provide the best performance. We design a work-conserving in-sequence striping algorithm and prove it to be sequence preserving and work conserving. The algorithm is then extended to practical data granularity. Performance analysis and simulation results demonstrate that our designs are able to preserve data sequence, reduce delay, and achieve 100% channel utilization.

An Efficient Model of DSSS System Using Multirate and Data Rate Transition Techniques

In this paper, an analytical and simulated approach has been developed for evaluating the performance of Bit Error Rate (BER) of Direct Sequence Spread Spectrum (DSSS). It is also demonstrated in this paper that how BER can be minimised using Rate Transition techniques. The work uses effective spreading sequence to achieve variable data rate transmission. In this research work, blind detection of the user signal has been considered assuming the receiver has prior knowledge of the user’s spreading code and is synchronised by using increased matched filter gain. Thus, it is not required to control the information to be transmitted along with the user signal. An attempt has also been made to show that how bandwidth utilisation has been halved using multirate techniques. This innovative research findings make use of implementing an efficient DSSS with reduced BER.

CARRIER RECOVERY AND CLOCK RECOVERY FOR QPSK DEMODULATION

This paper deals with the design and implementation aspects of high data rate digital demodulators. The Existing remote sensing satellites support data rates of several hundred mega bits per second. The future trend is towards giga bit rate transmission. This necessitates for demodulators of the ground receive system to process faster and handle the ever-rising data throughput more efficiently. Different Satellites use different modulation schemes with variable data rates. In order to cater to the Multi mission /Multisatellite data reception requirements of a ground station, it is necessary to have greater flexibility and programmability features embedded in the design of demodulators. The demodulation techniques for Binary / Quadrature Phase shift Keying (BPSK/ QPSK) are well established and understood when implemented with analog circuits. The BPSK/ QPSK can be demodulated by different techniques such as squaring loop, Costas loop and others in analog domain. The Costas loop technique is adopted for developing the digital demodulator because unlike in Square Loop technique, in this the carrier recovery and data demodulation can be done simultaneously with simple blocks level design. The high data rate digital demodulator performs IF amplification, filtering and analog to digital conversion of the received IF signal followed by a Digital demodulator. The basic design strategy includes a configurable data rate BPSK/ QPSK demodulation with COSTAS loop circuitry utilizing the flexibility of FPGA implementation. The basic design considering a sampling clock from local clock oscillator operating at 125 MHz and 70 MHz carrier down converted to 30 MHz for 8 Mbps data rate (For BPSK). Later the sampling clock is increased to 250 MHz and the carrier is direct 70 MHz with data rate 42.4456 Mbps (For QPSK). The Performance of the Demodulator is evaluated using MATLAB simulation tools. The development has done with ISE implementation tools. The purpose of this paper is to evaluate the new technology by implementing a BPSK/QPSK demodulator on an ADC-FPGA board. A mathematical algorithm was developed and implemented with ISE tools for digital demodulator design. The input test signals from Modulation Simulators and signal generators have been interfaced to the FPGA board through Analog-To-Digital Converter (ADC). The recovered carrier output and I, Q demodulated data patterns have been verified through ISE tools and Wave Vision Software for FFT analysis.

OPNET BASED SIMULATION AND INVESTIGATION OF WIMAX NETWORK USING DIFFERENT QOS

IEEE 802.16 WiMAX network is designed for providing high speed wide area broadband wireless access. WiMAX is an emerging wireless technology which is used for creating multi-hop mesh networks offering variable and high data rates, QoS, seamless mobility within a network. OPNET modeler is a simulation program tool used to simulate the different types of wireless networks. In this paper, simulation and evaluation of three different sized networks (small, medium, large) is carried out. We are using the modeler to study networks with 15, 25 and 40 mobile workstations. In each network, group of five WiMAX workstations connect and call each other through one WiMAX base stations during 1000sec. Performance of parameters that indicate the quality of services such as initial ranging activity, delay, total transmission power and PHY path loss have been studied.

An Efficient Dynamic Orthogonal Variable Spreading Factor Code Allocation Approach in WCDMA through Modified Adaptive Genetic Algorithm

Orthogonal Variable Spreading Factor (OVSF) codes would give variable data rate transmissions for different bandwidth supplies in Wideband CDMA (WCDMA) networks. These OVSF codes are used for the channelization of codes in WCDMA. In WCDMA, effective utilization of OVSF codes has become an active area of research as the number of codes is very limited. It is a fact that the successor and predecessor codes of OVSF cannot be used simultaneously when a specific code is used in OVSF as their encoded sequences become indistinguishable. Consequently, OVSF code tree has inadequate number of available codes. Thus, this research study uses Adaptive Genetic Algorithm (AGA) based approach for dynamic OVSF code assignment in WCDMA networks. Different from existing Conventional Code Assignment (CCA) and dynamic code assignment schemes, population is adaptively constructed according to existing traffic density in the OVSF code-tree. In existing technique in order to improve the ability of the GA, ＂dominance and diploidy＂ structure is employed to adapt to changing traffic conditions. Because in SGA algorithm cannot convergence if the new user is included into the existing OVSF code tree while SGA is running to find optimum OVSF code tree, SGA cannot adapt its structure to this unexpected variation. This problem can be overcome by the Modified Adaptive Genetic Algorithm (MAGA). Performance of the proposed MAGA approach is evaluated in terms of blocking probability and spectral efficiency and is compared with SGA, D&D GA.

Analysis of free space optical link in turbulent atmosphere

Free space optical (FSO) communication is an upgraded supplement to the existing wireless technologies. FSO technology provides vast modulation bandwidth, unlicensed spectrum, cost effective deployment, low power consumption and less mass requirement. Today, researchers are preliminary focused to use the free space communication systems for inter satellites links. In this paper, the performance analysis of FSO communication link in weak atmospheric turbulence has been analyzed for different atmospheric transmission windows using OOK modulation. The analysis has been done using bit error rate as the performance metric. The effect of attenuation on the link performance has been investigated by varying distance between transmitter and receiver for a given power and data rate. Further, BER performance analysis has been carried out for varying data rate and transmitted power. Also, the effect of attenuation on received optical power has been studied. The work has been performed in OptSim environment.