Transfer Capacity Research Articles

Heat transfer enhancement in cylindrical heat pipes with MgO-Al2O3 hybrid nanofluids in water-ethylene glycol mixture: An RSM approach

Heat pipes are passive devices crucial for thermal management in various applications. However, conventional water-based fluids can limit their heat transfer capacity, especially in cold environments where freeze protection is necessary. This study investigates the potential of MgO-Al2O3 hybrid nanofluids to enhance heat transfer performance in cylindrical mesh heat pipes while addressing these limitations. The research demonstrates significant improvements in thermal performance compared to a water-ethylene glycol mixture. The MgO-Al2O3 hybrid nanofluid reduces thermal resistance by enhancing surface wettability in the evaporator section. Additionally, the formation of a nanofluid coating on the evaporator surface leads to a higher heat transfer coefficient. Furthermore, RSM successfully models the relationship between nanoparticle concentration, power input, and key thermal responses (thermal resistance and heat transfer coefficient). These findings highlight the effectiveness of MgO-Al2O3 hybrid nanofluids for augmenting heat transfer in heat pipes and provide valuable RSM models for predicting thermal behavior within the investigated range.

Heat transfer and stratification behaviors of internally heated double-layer fluids systems under swinging conditions

To evaluate the safety designs aimed at the stratified corium pools for nuclear reactors applied in the marine environment, it’s important to carry out research on the convection related phenomena inside a layered fluids system under motion conditions. Thus, in this paper, the macroscopic characteristics of heat transfer and stratification for the double-layer fluids systems with internal heat source under motion conditions were studied through visualization experiments, and due to the complexity of actual ocean motions, only swinging motions were considered. In this research, a new dimensionless number Ris was proposed to quantify the effects of swinging motions, which represents the ratio of the characteristic buoyancy to the characteristic centrifugal force caused by swinging motions. Based on experimental results, swinging motions exert the most significant impacts on the layered systems when Ris is less than 1. In this case, the ratio of maximum temperature fT and the ratio of temperature difference between the two layers fΔT both dropped below 0.5, while the ratio of peak heat transfer capacity fQ-peak raised above 1.5, with the ratio of stable heat transfer capacity fQ-stable most probably lying within the range of 1.06 to 1.2. Additionally, several representative types of macroscopic interface deformation or stratification instability was observed, and phenomenon of mixing could appear between the double-layer fluids under intense-enough swinging conditions. These phenomena imply the significantly intensified forced convection inside the layered systems, which explains the sharply decreased temperature difference and the greatly enhanced heat transfer capacity during high-intensity swinging motions. By contrast, when Ris becomes larger than 10, the values of fΔT、fΔT and fQ-peak will be approaching to 1.0, and relatively stable stratification of the layered systems can be maintained, which indicates the increasingly negligible impacts of swinging motions in such cases. Besides, it was found that an increase in the thickness of either the lower-layer or the upper fluid also helped restrain interface deformation and enhanced the stratification stability of the layered systems.

Experimental and numerical investigation of a double spiral tube heat exchanger in a novel composite phase change material

Phase change energy storage technology effectively harnesses energy, and phase change materials have been garnered significant attention due to their high latent heat capacity. The heat transfer capacity and phase transition of HCNT − CH3COONa·3H2O/Na2HPO4·12H2O composites in a double spiral tube heat storage unit were investigated. The effects of different flow rates and temperatures on the heat transfer characteristics of phase change materials were studied, and the thermal performance of the storage units was evaluated by calculating the power, energy and energy efficiency ratios. The phase change process of the composite during heat transfer was further revealed via simulation, and the heat storage and heat release of the composite were compared with those of other phase change materials. The results show that the effects of the flow velocity on the transformation time and power of the phase change material are negligible. However, an increase in flow rate can significantly increase the heat storage and heat release of the phase change unit. In particular, when the flow rate is 4 LPM, the energy efficiency ratio can reach 76.6 %. When the temperature increases from 80 °C to 90 °C, the melting time decreases by 30.23 %, indicating that increasing the temperature has a significant effect on the phase transition process. Through simulation calculations, the composite phase change material shows significant performance advantages under the same working conditions; its heat storage capacity is 108 % greater than that of the other materials, and the heat release capacity is 206 % greater, which indicates that it has greater energy storage and release efficiency and a better thermal energy conversion capacity. In addition, the experimental and simulation results also reveal the existence of a diagonal region of slow phase transition in the heat storage unit. In summary, this paper analyses the heat transfer performance of a double spiral tube heat storage device, provides a theoretical basis for practical application, and provides an important reference for improving the performance of a phase–change energy storage system.

Effect of cold beverages on whole-body heat exchange in young and older males during intermittent exercise in the heat.

To mitigate health risks associated with occupational heat stress, workers are advised to adhere to a work-rest regimen, and hydrate regularly. However, it remains unclear if beverage temperature influences whole-body heat exchange during work-rest cycles, and if responses differ in older workers who have a blunted heat loss capacity. Ten young (mean [SD]: 22 [3] years) and 10 older (60 [4] years) males performed four 15-min bouts of moderate-intensity cycling at a fixed rate of metabolic heat production (200 W·m-2), each interspersed by 15-min rest in dry heat (40°C, ~12% relative humidity). On separate days, participants consumed either ice-slurry (~0°C), standardized to provide a heat transfer capacity of 75 kJ·m-2, or an identical mass of warm fluid (37.5°C) before the first and third exercise bouts. Evaporative and dry heat exchange (direct calorimetry) and metabolic heat production (indirect calorimetry) were measured continuously to determine cumulative heat storage (summation of heat loss and heat gain) over the entire protocol. Rectal temperature was also measured continuously. Relative to warm fluid, ice-slurry ingestion reduced cumulative heat storage in young (69 [181] vs. 216 [94] kJ) and older males (90 [104] vs. 254 [140] kJ, main effect: p < 0.01), but was unaffected by age (p = 0.49). However, rectal temperature was unaffected by beverage temperature in both groups (all p ≥ 0.15). We show that cold fluid ingestion is an appropriate administrative control for both young and older males as it can mitigate increases in body heat content during moderate-intensity work-rest cycles in dry heat.

Optimization of Parallel Data Transfers in Multi-Tiered Persistent Storage

A logical model of multi-tiered persistent storage provides a view of data where all available storage resources are distributed over a number of levels depending on the data transfer parameters and capacities. The efficient parallelization of data transfers in multi-tiered persistent storage is a significant challenge for a pipelined data processing model. This work examines a category of database applications implemented as sequences of operations that transfer data between the levels of multi-tiered persistent storage. The concept of EPN: Extended Petri Nets represents how database applications can be processed in parallel. A proposed transformation involves converting EPN into sequences of parallel data transfers. Additionally, a method is demonstrated for partitioning these sequences of data transfers, with the goal of reducing the total number of conflicts when data transfers occur between the levels of multi-tiered persistent storage. The paper proposes new rule-based algorithms for scheduling parallel data transfers that minimize total data transfer time. The objectives of the new algorithms are to evenly distribute the workload among the data transfer processes and reduce their idle time. Several experiments have confirmed the effectiveness of the new algorithms in generating parallel data transfer plans.

Assessment of Energy Recovery Potential in Urban Underground Utility Tunnels: A Case Study

Underground spaces contain abundant geothermal energy, which can be recovered for building ventilation, reducing energy consumption. However, current research lacks a comprehensive quantitative assessment of its energy recovery. This research evaluates the energy recovery potential of the Xingfu Forest Belt Urban Underground Utility Tunnels. Field experiments revealed a 7 °C temperature difference in winter and a 2.5 °C reduction during the summer-to-autumn transition. A computational fluid dynamics (CFD) model was developed to assess the impact of design and operational factors such as air exchange rates on outlet temperatures and heat exchange efficiency. The results indicate that at an air change rate of 0.5 h−1, the tunnel outlet temperature dropped by 10.5 °C. A 200 m tunnel transferred 8.7 × 1010 J of heat over 30 days, and a 6 m × 6 m cross-sectional area achieved 1.1 × 1011 J of total heat transfer. Increasing the air exchange rate and cross-sectional area reduces the inlet–outlet temperature difference while enhancing heat transfer capacity. However, the optimal buried depth should not exceed 8 m due to cost and safety considerations. This study demonstrates the potential of shallow geothermal energy as an eco-friendly and efficient solution for enhancing building ventilation systems.

Construction of electrochemical immunosensor from MXene/multi-walled carbon nanotubes/gold nanoparticles for specific detection of carcinoembryonic antigen.

With the advancement of nanotechnology, various types of nanomaterials have been integrated into electrochemical immunoelectrodes to enhance their performance. Among these, MXene stands out as a promising candidate due to its high electron transfer capacity and abundant surface chemical groups. However, the improvement in electrode performance is often hindered by the self-restacking and agglomeration of MXene. To address this issue, multi-walled carbon nanotubes (MWCNTs) were selected to form composites with MXene. Subsequently, a label-free immunosensor, BSA/Ab/AuNPs/MXene-MWCNTs-Nafion/ITO, was fabricated for specific detection of carcinoembryonic antigen (CEA), a widely used tumor marker. The results demonstrated that the incorporation of MWCNTs can effectively prevent the self-stacking of MXene. Moreover, the composites enhanced the loading of gold nanoparticles (AuNPs) to connect the antibodies, thereby improving electronic transmission signals and sensitivity. The sensor exhibited excellent analytical performance towards CEA with a wide linear range (0.050 to 200ngmL-1) and a low limit of detection of 0.015ngmL-1 (S/N = 3). The possibility of it being applied in clinical trials was verified by using ELISA and differential pulse voltammetry (DPV) assays to detect CEA in serum samples. The recoveries ranged from 95.34 to 102.09% with relative standard deviations (RSDs) below 5.00%. Furthermore, the sensor displayed satisfactory selectivity, repeatability, and stability. We hope the findings highlight promising prospects for advanced immunosensor development and alternative strategies in cancer diagnosis.

Non-steady flow decomposition behaviors of heat and mass transfer on intrinsic kinetics for methane hydrate particles transported in pipelines

The differential equations governing the decomposition rate and activation energy, convective mass transfer, methane diffusion and fugacity, as well as heat conduction and enthalpy change were derived by integrating thermal convection, heat conduction, mass transfer and intrinsic kinetics. Mathematical models for decomposition kinetics and thermodynamics in a non-steady field were solved using a radial logarithmic grid for node division and discretization of the equations. The study elucidated the heat and mass transfer processes as well as decomposition kinetics in pipelines by analyzing the impacts of particle size, temperature, pressure, flow rate and activation energy on decomposition rate. The results indicated that compared with the isothermal decomposition of the intrinsic kinetic model and static experimental decomposition, the complex non-steady multiphase flow model offers a more accurately simulation of hydrate decomposition as well as associated heat and mass transfer processes. Hydrate decomposition is characterized as a non-isothermal dynamic ablation process with heat transfer rate and intrinsic kinetics dominating during the preliminary stage and the stable stage, respectively. An increasing in the slurry temperature, temperature fluctuation and flow rate accelerated the heat transfer rate capacity, enhanced convective heat transfer capacity and facilitated hydrate decomposition, with the mass transfer rate exhibiting lesser influence. The particle surface area and slurry temperature exhibited the most significant influence on hydrate decomposition, which was followed by flow rate. Upon increasing particle size from 1 mm to 5 mm and the temperature from 293 K to 313 K, the decomposition rate increased by 20.7 times and 13.5 times, respectively. Furthermore, enhancing temperature and flow rate while decreasing particle size and pressure decreased both the decomposition time and the duration required for the decomposition rate to reach its peak. Additionally, the decomposition rate and its constant vary with the activation energy.

Heat transfer and entropy production analysis of Casson nanofluid under cylindrical stretching motion in the existence of aggregates nanoparticles

This paper focuses on the heat transfer and entropy production of the Casson nanofluid under cylindrical stretching motion in the case of nanoparticle aggregation. Calculations derived from the BVP4C numerical solution were utilized in the study to verify the accuracy of the calculations in comparison with previous results. The results showed that when the nanoparticle volume fraction was increased from 1% to 3%, the heat transfer efficiency improved by 2.72% in the absence of nanoparticle aggregation, while the heat transfer efficiency improved by 12.42% in the existence of nanoparticle aggregation. It is also found that the existence of aggregation of nanoparticles significantly increased the heat transfer capacity and flow resistance of the Casson nanofluid compared to the absence of aggregation. The results of this study can provide important theoretical support for applications in thermal management of stretched cylinders, biomedical drilling, and other fields.

Solar thermal cooking device for domestic cooking applications: Bridging sustainable development goals and innovation

Fossil fuels are vital in the cooking field rather than the automotive sector. Hence, solar cooking has been popularized in recent years due to the rising cost of cooking gas. However, implementing successful renewable energy for cooking in urban area is still challenging for industries. Hence, a solar thermic cooking device with a compact size suited for domestic cooking in urban area is proposed. Thus, the solar cooking device will be developed as a fully functional prototype with necessary supporting modules, depending on the heat transfer fluid (HTF) flow and heat transfer rate between fluids. The main objective is to represent various computational fluid dynamics (CFD) and thermal analysis results on different optimistic designs for a solar thermoelectric cooking device's heat exchanger and storage unit. The 3D part model of the modules has been developed using SOLIDWORKS 2019 software. CFD has also been carried out using the same workspace with an additional package called flow simulation to analyze the flow properties of heat transfer fluid at different rates when circulated in other modules.Moreover, the thermal behavior of the HTF concerning the heat transition between module surfaces is simulated using SOLIDWORKS flow simulation to evaluate the heat storage capacity and rate of heat transfer. The theoretical formulations for the modules are derived through thermodynamic equations concerning the materials and fluid involved in the unit. The thermal and CFD analysis is carried out for different optimistic 3D models based on thermal sustainability, and the results are compared with theoretical analysis, which is discussed in this paper.

Effect of Cu doping on morphology and properties of calcium ferrite and its application as oxygen carrier in chemical looping hydrogen production

Chemical looping hydrogen production with inherent CO2 capture has been widely recognized as a clean and efficient approach to high-purity hydrogen production because of the ultra-pure H2 product without any purification facilities. It is crucial to develop oxygen carriers with better performance to improve fuel conversion and hydrogen production efficiency. The potential of Ca2Fe2O5 in steam converting has been confirmed. However, its lower oxygen transfer capacity, that is, it tends to produce lower fuel conversion in fuel reactors, which will limit its practical application. Here, we report the development of Cu-doped Ca2Fe2O5-based oxygen carriers using sol-gel technology. The effects of B-site substitution of Cu element on the morphological properties and redox properties of Ca2Fe2-xCuxO5 (x = 0, 0.1, 0.25, 0.5, 1) oxygen carriers were evaluated based on experiments and density functional theory calculations. The results show that Cu doping not only elevated the surface oxygen content and enhanced the oxygen activity of the oxygen carriers, but also increased the Fe3+ at the B-site, thus enhanced their binding ability with oxygen molecules. Vacancy formation was a rate-determining step in the chemical looping hydrogen production (CLH), and Cu-doped Ca2Fe2O5 reduced the energy of oxygen vacancy formation. In the CLH process, the doping of Cu significantly improved the hydrogen productivity and fuel conversion rate. The fuel conversion rate was positively correlated with the doping amount of Cu. When x = 1, Ca2Fe2-xCuxO5 had the maximum fuel conversion rate, and its average conversion was 54.2% more than that of undoped Ca2Fe2O5. Ca2Fe2-xCuxO5 with x = 0.25 was the most suitable for CLH with the highest H2 yield, which was 20.3% more than that of Ca2Fe2O5. Moreover, its properties remained stable over multiple redox cycles with high activity and stability for CO-CLH.

Improved adsorption and charge transfer capacity by coupling g-C3N4 and NH2-MIL-125 for efficient degradation of sulfamethoxazole in water: Characterization, degradation efficiency, influence factors, and mechanism

Photocatalysis is an advanced oxidation process that shows excellent promise in degrading organic pollutants present in water. However, electrons and holes tend to combine easily during the transfer process, and the adsorption capacity of single-phase photocatalytic materials is weak, resulting in a low degradation rate. Therefore, a new composite semiconductor photocatalyst g-C3N4/NH2-MIL-125 was constructed using a two-step solvothermal method. The morphology, elemental composition, structure, photoelectric properties, and photocatalytic activity of g-C3N4/NH2-MIL-125 were characterized. The photocatalytic degradation of Sulfamethoxazole (SMX) in water was also carried out. Results indicated that g-C3N4/NH2-MIL-125 had been synthesized successfully, and g-C3N4/NH2-MIL-125 had a broader photoresponse range, higher adsorption capacity, and higher separation efficiency of photogenerated carriers. When pH was 4.0 and catalyst dosage was 0.15 g/L, g-C3N4/NH2-MIL-125 showed the highest degradation rate for SMX. It was confirmed that the main active groups in SMX degradation were OH, h+, and O2−. 15 kinds of intermediates of SMX and the possible degradation pathways were identified by high-performance liquid chromatography-mass spectrometry and DFT calculation. Toxicity analysis revealed that the intermediate products have a lower developmental toxicity than SMX. This work demonstrated that g-C3N4/NH2-MIL-125 has great potential in eliminating antibiotics from water.

Deciphering heterojunction layered double hydroxide-polyaniline-carbon nanotubes for phosphorus capture in capacitive deionization

The capacitive deionization (CDI) has emerged as a robust technology due to its effective performance in removing and recovering phosphate in wastewater. However, there are still challenges in achieving fast charge transfer and high capacity phosphorus storage simultaneously. In this study, a layered double hydroxide-polyaniline-carbon nanotubes composite material (ZnFe-PANI/CNT) with heterojunction and pseudocapacitive characteristics was fabricated via a simple and effective precipitation strategy. The existence of heterojunction and pseudocapacitance of ZnFe-PANI/CNT was confirmed through material performance testing Moreover, with its fast charge transfer and high ion storage performance, it was achieved high phosphate adsorption efficiency (94 %) and sustainable electrode regeneration in low concentration phosphate wastewater. Ultraviolet photoelectron spectroscopy (UPS) and density functional theory revealed the ability to accelerate charge transfer, which was contributed by the heterojunction ZnFe-PANI/CNT. In addition, it was found that the synergies of electrostatic attraction, ligand exchange and surface complexation contributed to the high phosphate capture ability in the acidic environments. The binuclear bidentate or mononuclear bidentate structures dominated the surface configuration of phosphate adsorption at pH 4–9.

Airfoil cross flow field to enhance mass transfer capacity and performance for PEMFC

Proper design of the flow field in bipolar plates is important for improving proton exchange membrane fuel cells in water transport, gas distribution and net power density enhancement. Inspired by the fact that the streamlined design of an airplane airfoil makes the flow resistance reduced, a new airfoil cross flow field is proposed. Airfoil cross flow field is composed of a regular pattern of airfoil pins which are categorized in pin-type flow fields. The effects of different airfoil-pin shapes and arrangements on cell performance were explored. The results showed that airfoil cross flow field improved water management by finely modulating the airflow significantly increasing the gas flow rate in the channel. In addition, the airfoil cross flow field design achieves higher and more uniform oxygen distribution at the interface between the gas diffusion layer and the catalyst layer. The proper shape and arrangement of the airfoil-pins can effectively increase the net power density of the cell by 10.65 % and 2.49 % compared to the conventional parallel flow field and the square-pin flow field. Due to the streamlined design of the airfoil cross flow field, the voltage drop is approximately 60 % of that of the conventional parallel flow field and even slightly lower than that of the square-pin flow field, which demonstrates its high practicality. In summary, the airfoil cross flow field well coordinates the high current density and low voltage drop requirements of proton exchange membrane fuel cells, and some new points of view on flow field design are presented.

The Effects of Diabetes on Gas Transfer Capacity, Lung Volumes, Muscle Strength, and Cardio-pulmonary Responses During Exercise.

Diabetes is a risk factor for the development of vascular disease, chronic kidney disease, retinopathy, and neuropathy. Diabetes is a co-morbid condition commonly present in patients with respiratory disorders but the extent to which it influences ventilatory capacity, gas exchange, and functional capacity is not well known. Research question Does the presence of diabetes contribute to impairment in spirometry, gas transfer, and exercise capacity? Retrospective analysis of all subjects who performed incremental cardio-pulmonary exercise testing (CPET) between 1988 and 2012 at McMaster University Medical Centre. The impact of diabetes on physiological outcomes and maximum power output (MPO) was assessed using stepwise multiple additive linear regression models including age, height, weight, sex, muscle strength, and previous myocardial infarct as co-variates, and was also stratified based on BMI categories. 40,776 subjects were included in the analysis; 1938 (5%, 66% male) had diabetes. Diabetics were older (59 vs. 53 years), heavier (88.3 vs.78.0 kg), and had a higher BMI (31 vs. 27kg/m2). The presence of diabetes was independently associated with a reduction in FEV1 (-130ml), FVC (-220ml), DLCO (-1.52ml/min/mmHg), and VA (-340ml) but not KCO. Patients with diabetes achieved a lower % predicted MPO[diabetic subjects 70% predicted (670 kpm/min ± 95% CI 284) vs. 80% in non-diabetics (786 kpm/min ± 342), p < 0.001]. With the exception of KCO, these differences persisted across BMI categories and after adjusting for MI. The presence of diabetes is independently associated with weaker muscles, lower ventilatory and gas transfer capacity and translates to a lower exercise capacity. These differences are independent of age, height, weight, sex, and previous MI.

Physioxia rewires mitochondrial complex composition to protect stem cell viability

Human induced pluripotent stem cells (hiPSCs) are an invaluable tool to study molecular mechanisms on a human background. Culturing stem cells at an oxygen level different from their microenvironmental niche impacts their viability. To understand this mechanistically, dermal skin fibroblasts of 52 probands were reprogrammed into hiPSCs, followed by either hyperoxic (20 % O2) or physioxic (5 % O2) culture and proteomic profiling. Analysis of chromosomal stability by Giemsa-banding revealed that physioxic -cultured hiPSC clones exhibited less pathological karyotypes than hyperoxic (e.g. 6 % vs. 32 % mosaicism), higher pluripotency as evidenced by higher Stage-Specific Embryonic Antigen 3 positivity, higher glucose consumption and lactate production. Global proteomic analysis demonstrated lower abundance of several subunits of NADH:ubiquinone oxidoreductase (complex I) and an underrepresentation of pathways linked to oxidative phosphorylation and cellular senescence. Accordingly, release of the pro-senescent factor IGFBP3 and β-galactosidase staining were lower in physioxic hiPSCs. RNA- and ATAC-seq profiling revealed a distinct hypoxic transcription factor-binding footprint, amongst others higher expression of the HIF1α-regulated target NDUFA4L2 along with increased chromatin accessibility of the NDUFA4L2 gene locus. While mitochondrial DNA content did not differ between groups, physioxic hiPSCs revealed lower polarized mitochondrial membrane potential, altered mitochondrial network appearance and reduced basal respiration and electron transfer capacity. Blue-native polyacrylamide gel electrophoresis coupled to mass spectrometry of the mitochondrial complexes detected higher abundance of NDUFA4L2 and ATP5IF1 and loss of incorporation into complex IV or V, respectively. Taken together, physioxic culture of hiPSCs improved chromosomal stability, which was associated with downregulation of oxidative phosphorylation and senescence and extensive re-wiring of mitochondrial complex composition.

Maximum exercise capacity: Barcroft revisited in a large population

RATIONALE In 1973, the first exercise test was performed at McMaster University Medical Center to provide a standardized approach to clinical exercise testing, based on Barcroft’s maxim that the maximum capacity to exercise is “the essence of the machine,” emphasizing integration between different mechanisms. The test was incremental ergometer exercise to symptom limited maximum. Physiologic and symptom measurements were made before and during exercise. 46,288 tests were collected and entered into a dataset; unique both in terms of the large number and the physiologic variables collected (skeletal muscle strength, gas transfer capacity, symptoms). OBJECTIVES The objective of this study was to understand CO2 production in relation to oxygen uptake when exercising to maximum capacity. MEASUREMENTS AND MAIN RESULTS Physiologic factors contributing to maximum exercise capacity (Wmax) were skeletal muscle strength, FEV1 (ventilatory capacity) and DLCO (gas transfer capacity). The response of VCO2 in relation to VO2 (RER) showed a lag in CO2 production (related to CO2 storage), which was longer in subjects with higher maximum exercise capacity. This lag was followed by a progressive increase toward W max that reached a maximum value independent of W max. The perceived intensity of leg effort and dyspnea increased in a positively accelerating manner in parallel with increases in CO2 output. CONCLUSION Maximum power in incremental cycling was symptom limited, dependent on muscle (strength, oxidative capacity), together with FEV1. Previous emphasis on oxygen delivery as limiting exercise, irrespective of clinical diagnosis, may be augmented by the perceptual limitation that accompanies, remarkably symmetrically, the adaptation to CO2 removal maintaining homeostasis in muscle (muscle buffering capacity).

Experimental Study of Single and Two-Phase Flow and Heat Transfer Characteristics in Helical Tube under Motion Condition

The unique structural characteristic of the helical coiled pipe causes some special phenomena such as the secondary flow effect inside the tube, and the heat transfer characteristics are more complicated than those in circular pipe. There have been few published papers about experimental research of flow and heat transfer characteristics of helical tube under motion conditions. An experimental loop was built based on the background above. An experimental study of single-phase and saturated boiling two-phase heat transfer characteristics and flow instability in helical tubes under multiple motion conditions was carried out. In which the maximum system pressure was 4 MPa, mass flux was 550 kg/(m2·s), and heat flux of the test section was 360 kW/m2. The results show that the heat transfer capacity of the side close to the central axis of the helical tube is significantly lower than that of the side away from the central axis under rocking and inclination conditions. An empirical correlation of the heat transfer coefficient in helical tube under static and motion conditions was drafted based on the experiment data of single-phase conditions. The influence of motion conditions on two-phase heat transfer characteristics was similar to that of a single phase but much weaker.

Ice source heat pump system for energy supply via gas pipelines – Part1: Performance analysis in residential units

This study evaluates the performance of heat pumps using water or ice as the heat source, with energy transferred via repurposed gas delivery pipes. The proposed system offers significant benefits for urban energy networks, particularly in densely populated areas. The article is divided into two main sections: the first compares the thermal efficiency of the proposed system for residential heating against similar heat pumps. The second section examines the implementation, energy transfer capacity, and water requirements of using a gas pipeline network. The study models various heating systems, including electric-resistance, air-source, water-source, ground-source, and ice-source heat pumps, in Nottingham throughout the year. The results show that switching from gas to heat pumps significantly increases electricity demand, especially during peak periods. Specifically, electric-resistance heating, air-source, water-source, and ice-source heat pumps increase peak electricity consumption by factors of 7.5, 3.2, 2.5, and 2.7, respectively, compared to a gas boiler. Additionally, electricity consumption exceeds the current peak for 89 %, 47 %, 35 %, and 39 % of the hours in the year for each respective system. These findings emphasize the proposed system's role in managing peak electricity demand and enhancing generation and transmission capacity post-natural gas phase-out.

The evolution of structural characteristics and redox properties of humin during the composting of sludge and corn straw.

Humins (HMs), the insoluble faction of humic substances (HSs), play a pivotal role in the bioremediation of pollutants by acting as electron shuttles that modulate the interactions between microorganisms and pollutants. This crucial function is intricately linked to their structural composition and electron transfer capabilities. However, the dynamics of the electron transfer capacity (ETC) of HM extracted during the composting process and its determinants have yet to be fully elucidated. This study undertakes a comprehensive analysis of the ETC of HM derived from composting, employing electrochemical techniques alongside spectroscopic methods and elemental analysis to explore the influencing factors, including the electron accepting capacity (EAC), electron donating capacity (EDC), and electron reversible rate (ERR). Our findings reveal substantial variations in the EAC and EDC of HM throughout the composting process, with EAC values ranging from 133.03-220.98 μmol e- gC-1 and EDC values from 111.17-229.33 μmol e- gC-1. Notably, the composting process enhances the ERR and EDC of HM while diminishing their EAC. This shift is accompanied by an augmented presence of aromatic structures, polar functional groups, quinones, and nitrogen - and sulfur-containing moieties, thereby boosting the HM's EDC. Conversely, the reduction in EAC is associated with a decline in lignin carbon content and the abundance of oxygen-containing moieties, as well as the diminishment of visible fulvic-like and protein-like substances within HM. Importantly, humic-like substances and nitrogen-containing moieties within HM demonstrated the capacity for repeated electron transfer, underscoring their significance in the context of environmental remediation.