Temperature Fluctuations Research Articles

Mitigating urban heat island and enhancing indoor thermal comfort using terrace garden

The United Nations advocates for sustainable urban planning and design, emphasizing green infrastructure initiatives to mitigate urban heat island effects and enhance the resilience and livability of cities globally. To address urban heat challenges, a study was conducted in Chennai, India, from April to June 2023. The study focused on assessing temperature dynamics on a building's terrace by comparing a well-maintained garden area with an exposed region. Temperature and humidity sensors were deployed in both the garden and exposed areas of the terrace, as well as within rooms beneath it, to monitor hourly temperature fluctuations. The findings indicate a significant reduction in internal room temperatures in areas with rooftop gardens, ranging from 4 to 11 °C, depending on the time of year and sun's position, compared to rooms with fully exposed roof configurations. Additionally, simulation studies were performed to validate these findings, suggesting that optimizing the distribution of soil beds and plant density across the roof could yield an additional temperature reduction of 3–4 °C, resulting in an overall difference of up to 14–15 °C. The study highlights the efficacy of rooftop gardens in providing cooling effects during daylight hours and maintaining temperature parity post-sunset. Through analysis of sensor data, the research elucidates the intricate relationship between green infrastructure and thermal comfort, offering insights for energy-efficient building design and resilient urban planning. The findings underscore the potential of rooftop gardens in fostering a more comfortable, energy-efficient, and sustainable urban living environment.

ПРОГРАММНО-АЛГОРИТМИЧЕСКОЕ ОБЕСПЕЧЕНИЕ ИНТЕЛЛЕКТУАЛЬНОЙ СИСТЕМЫ ТЕХНИЧЕСКОГО ЗРЕНИЯ ДЛЯ ОПРЕДЕЛЕНИЯ ПАРАМЕТРОВ КОРНЕПЛОДОВ САХАРНОЙ СВЕКЛЫ ПРИ СОРТИРОВКЕ ПЕРЕД УКЛАДКОЙ НА ХРАНЕНИЕ

The application of methods of long-term storage of sugar beet for a period of more than 2 months is justified. It has been found that small root crops are more susceptible to temperature fluctuations and relative humidity of the environment, which leads to a change in the partial pressure of water vapor between the surface of sugar beet and the surrounding air. During storage in a sugar beet mound, the relative humidity reaches from 90 to 95% due to the removal of moisture from the surface of root crops, which is a source of beet mass losses. The criteria for the size of sugar beet root crops have been determined. The necessity of creating a method for sorting trucks at the receiving point of sugar factories is shown. It was revealed that when determining the requirements for sugar beet entering storage, it is necessary to take into account, in addition to physical and chemical parameters, the value of the specific surface area of the root crop. Therefore, it is recommended to send large root crops weighing more than 570 g to kagats. The purpose of the article is formulated, which is to develop software and algorithmic support for determining the parameters of sugar beet root crops when sorting trucks. The process of distribution of trucks at the receiving point of sugar factories by man at the present time is described. A block diagram of the algorithm of the intelligent vision system program is presented and described. The features of the created software are described, such as working with sensors, processing software or hardware errors. According to the results of the study, an algorithm for the operation of the program and software of an intelligent vision system for determining the parameters of sugar beet root crops have been developed [1].

Convolutional denoising for large-volume Seebeck calorimeter

Ambient temperature fluctuations can affect the thermal noise and sensitivity of a large-volume Seebeck calorimeter. This paper proposes that a reference cell considerably smaller than the sample cell in the apparatus can effectively neutralize this noise. It is found that the thermal signals from both the reference and sample cells exhibit a convolution relationship. By deconvolving two distinct thermal pulses generated by abrupt changes in cooling fluid temperature, one from the reference cell and one from the sample cell, a corresponding response function is derived. And using this function, the noise is canceled out by subtracting the convoluted signal of the reference cell from that of the sample cell during isothermal calorimetry. Experimentally, utilizing this technique with two calorimeters, one with a 17.6-liter capacity and the other with a 27-liter capacity, has been shown to reduce noise by at least 5 % and 6 % from their initial values, respectively.

Seed Priming and Media for Enhanced Seedling Growth in Pansy (Viola tricolor)

The alarming increase of temperature in Northern areas of India makes it difficult to grow seeds due to these temperature fluctuations. Since Punjab is the hub of annual flower seed production it becomes imperative to identify suitable seed primming and growing media for proper growth and germination of seedlings of annual flower crops. Hence this investigation was conducted in PAU, Ludhiana to evaluate different pre sowing seed treatment and growing media in pansy seeds for better growth and development of seedlings. The maximum shoot length (5.75cm), root length (5.38 cm), number of leaves per plant (8.00), fresh weight (14.04g), dry weight (1.42 g) and SPAD index (34.43) was recorded through synergistic effect of GA3 @ 25 ppm + soil: cocopeat: vermicompost (1:1:1) in pansy. Therefore, it was concluded from the study that treatment combination of GA3 @ 25 ppm + soil: cocopeat: vermicompost (1:1:1) was found to be the best for almost all parameters as compared to the other treatments.

Unveiling the impact of temperature shift on microbial community dynamics and metabolic pathways in anaerobic digestion

Anaerobic digestion (AD) technology is a viable solution to the challenges attributed to sewage sludge, but its specific impact on biogas production and the dynamics of methanogenic bacteria has not been widely understood. This research investigated the effects of shifts in AD operational temperatures on microbial communities and biogas production. This was achieved by incrementally raising the temperature from 37 °C to 45 °C in 2 °C increments. Within the temperature range of 37 – 41 °C, there was a notable disturbance in the abundance of acetogenic bacteria and methanogens, leading to a considerable reduction in methane production. However, with further elevation of temperature, the increasing activity of acetogens and methanogens was discerned following the increase in methane production. Methanothrix was identified as the predominant methanogen in the present study, marking the domination of the acetoclastic pathway. In functional analysis, the acetate decarboxylation enzymes demonstrated resilience at 43 °C and 45 °C, in contrast to hydrogenotrophic pathway enzymes. The acetoclastic pathway played a primary role in methane production under temperature shift conditions while the hydrogenotrophic pathway was more susceptible to temperature fluctuations. The findings highlight the potential adaptation of microbial communities when subjected to changing temperatures which led to robustness of digestion in AD processes.

Seasonal meropenem resistance in Acinetobacter baumannii and influence of temperature-driven adaptation

BackgroundRecognition of seasonal trends in bacterial infection and drug resistance rates may enhance diagnosis, direct therapeutic strategies, and inform preventive measures. Limited data exist on the seasonal variability of Acinetobacter baumannii. We investigated the seasonality of A. baumannii, the correlation between temperature and meropenem resistance, and the impact of temperature on this bacterium.ResultsMeropenem resistance rates increased with lower temperatures, peaking in winter/colder months. Nonresistant strain detection exhibited temperature-dependent seasonality, rising in summer/warmer months and declining in winter/colder months. In contrast, resistant strains showed no seasonality. Variations in meropenem-resistant and nonresistant bacterial resilience to temperature changes were observed. Nonresistant strains displayed growth advantages at temperatures ≥ 25 °C, whereas meropenem-resistant A. baumannii with β-lactamase OXA-23 exhibited greater resistance to low-temperature (4 °C) stress. Furthermore, at 4 °C, A. baumannii upregulated carbapenem resistance-related genes (adeJ, oxa-51, and oxa-23) and increased meropenem stress tolerance.ConclusionsMeropenem resistance rates in A. baumannii display seasonality and are negatively correlated with local temperature, with rates peaking in winter, possibly linked to the differential adaptation of resistant and nonresistant isolates to temperature fluctuations. Furthermore, due to significant resistance rate variations between quarters, compiling monthly or quarterly reports might enhance comprehension of antibiotic resistance trends. Consequently, this could assist in formulating strategies to control and prevent resistance within healthcare facilities.

Experimental study on thermal and humidity properties of modified rammed earth buildings in winter

Rammed earth materials have been used in traditional buildings for thousands of years. Currently, with the interest in environmentally friendly societies, rammed earth construction has regained attention owing to its characteristics of energy conservation, environmental protection, low cost, and local material extraction. In this study, cement, gravel, sand, and polypropylene fibers were used as the modifying materials of rammed earth. The thermal and humidity physical parameters are measured at different moisture contents after modification, and the isothermal hygroscopic curves are fitted. The experimental findings demonstrated positive correlations between the specific heat capacity and thermal conductivity and the moisture content. The temperature and humidity of a modified rammed earth test building were recorded for seven days during winter. The test findings revealed that, throughout the test, the moisture content in the middle of the wall was consistently higher than that in the inner surface. When the outdoor temperature fluctuation was 14.95 °C, the inner surface temperature and indoor temperature fluctuation were 2.73 °C and 3.08 °C, respectively. Moreover, the inner surface temperature of the wall became maximum 7–8 h after the maximum outer surface temperature is reached, on average. The above data show that a modified rammed earth wall has exceptional heat and moisture storage capacities as well as heat and moisture buffering characteristics, which can reduce fluctuations in indoor temperature and humidity and create a more comfortable indoor living environment.

Improving freeze resistance of cement-based materials with modified graphite-paraffin composite low-temperature microencapsulated phase change materials

This study examines the influence of microencapsulated phase change materials (MPCM) on enhancing the freeze-thaw resistance of cementitious structures, overcoming the limitations commonly associated with traditional phase change materials (PCM), such as insufficient thermal conductivity and non-optimal phase change temperatures. The research focused on developing MPCM with improved thermal conductivity and lower phase transition points, utilizing a binary mixture of tetradecane and hexadecane as the core material, supplemented by modified graphite. The phase change performance and physicochemical stability of the prepared MPCM were thoroughly assessed. Cement specimens, incorporating different contents of MPCM, were then subjected to a series of tests under both room temperature and simulated freeze-thaw conditions. These tests included mechanical testing, temperature response experiments, and monitoring of internal damage. The findings identified the optimal MPCM formulation as a 9:1 mixture of tetradecane and hexadecane, with an addition of 2 % hydrophobically modified graphite, which exhibited a phase change temperature near 0 °C and a range exceeding 6.7 °C, along with stable physicochemical properties. When 3 % MPCM was included in cement specimens cured for 28 days under freeze-thaw conditions, a significant reduction in internal damage caused by freeze-thaw cycles was observed, leading to an increase in compressive strength by 0.12 % and in flexural strength by 11.77 %. Additionally, temperature tests confirmed the efficacy of MPCM in stabilizing internal temperature fluctuations within the cement specimens. The results of this study present a viable approach to enhance the durability of cement-based infrastructure in cold climates.

Mathematical model and electronic system for real-time O2 control in storage boxes: Development and validation under fluctuating temperatures

Modified atmosphere storage containers with gas-permeable membranes are effective in reducing post-harvest losses, mainly at low temperatures but become ineffective in controlling O2 and CO2 at temperatures above 3 °C. This study aimed to develop a method to control O2 in a storage box. This method uses a diffusion tube, that blocks air from entering the box but allows for air exchange when an air blower is activated. The blower ON frequency (BOF) was modelled as a function of temperature, considering the type and amount of produce, blower properties, tube dimension, and the O2 setpoint. The effects of temperature and gas composition on respiration rate kinetics were analysed with Michaelis-Menten and Arrhenius equations. The model was used to program the microcontroller to control the blower. Validation was performed using a 190 L box containing 25 kg of broccoli. The developed model maintained the desired O2 concentration under fluctuating temperatures. The BOF values ranged from 25.6 to 549.2 s h−1, for temperature fluctuations between 4 and 23 °C. The time required to reach the 3% O2 in the box differed depending on the blower's state. With the blower turned ON from the beginning, it took 24.9 h. However, when the blower was initially turned OFF, it took 11.1 h. Despite temperature changes, the system maintained O2 at 3.8 ± 0.29% and CO2 at 14.4 ± 0.66%. The system is promising for commercial use and best suited for CO2 tolerant produce because it requires a separate mathematical model and control mechanism.

Analyzing Urban Climatic Shifts in Annaba City: Decadal Trends, Seasonal Variability and Extreme Weather Events

Global warming is one of the most pressing challenges of our time, contributing to climate change effects and with far-reaching implications for built environments. The main aim of this study is to assess the extent to which Annaba city, Algeria, as part of the Mediterranean region, is affected by global climate change and its broader influences. The study investigated climatic shifts in Annaba city, using a multi-step methodology integrating data collection and analysis techniques. Data collection included 23 years of climate data (2000–2023) from Annaba’s meteorological station, on-site measurements of microclimatic variations, and a questionnaire survey. The collected data underwent four main analyses: a time series analysis to describe climate parameters over 23 years, a statistical analysis to predict potential future climatic conditions (2024–2029) and the correlation of various climatic variables using specialized bioclimate tools to highlight seasonal variability, a spatial study of the urban heat island (UHI) phenomenon and perceived climatic shifts, and an analysis of extreme weather events characterizing heat atmospheric events in the context of urban climate change in the Mediterranean region. The findings revealed a consistent warming trend in Annaba city, with prolonged extreme climate conditions observed, particularly in the last four years (2020–2023). Significant temperature fluctuations were emphasized, notably in July 2023, with record-breaking maximum temperatures reaching 48.2 °C, the hottest on record with an increase of 3.8 °C, and presenting challenges amplified by the urban heat island effect, causing temperature differentials of up to 6 °C within built-up areas. Projections for 2029 suggest a tendency towards heightened aridity with a significant shift towards a new climate seasonality featuring two distinct main seasons—moderate and hot challenging. The abrupt disruption of calm weather conditions in Annaba on 24 July 2023 highlighted the influence of atmospheric circulation within the Mediterranean region featured for both anticyclones and atmospheric blocking phenomena on local weather patterns.

Dynamic modelling of supplemental cooling systems with vapor compression refrigeration units in civil aircrafts

Newly developed airliners have adopted supplemental cooling systems (SCS) to provide for non-cabin cooling requirements. In the present study, dynamic component models for compressor and phase change heat exchangers were developed with dynamic decoupling and explicit solution methods, and pressure zone separation and solution methods are developed based to obtain dynamic pressures as key values. A dynamic VCRU subsystem model is established, and the result under single-unit startup condition shows pressure deviations less than 0.16 %, with a simulation time ratio of 5.65 %, exhibiting good overall performance at both precision and speed. A dynamic SCS system model is developed, and the simulation of a 9000 s flight took 1973.3 s to complete. Result in the cruise phase shows the condensation and evaporation temperatures are in the ranges of 28.39–31.33 °C and −17.93 to −10.71 °C, respectively, meeting their respective designed ranges of 30 ± 5 °C and −15 ± 5 °C. These results reflects good consistency of the model with actual system characteristics. Control optimization is conducted based on the developed model to eliminate temperature fluctuation. The optimization reduced the maximum temperature deviation from 0.4004 K to 0.0019 K after system starting process, proving the feasibility of control method optimization based on the developed dynamic simulation model.

Magneto Hydrodynamic Effects on Unsteady Free Convection Casson Fluid Flow Past on Parabolic Accelerated Vertical Plate with Thermal Diffusion

The free convection MHD flow of a viscous, chemically reactive, electrically conducted, incompressible, and Casson fluid past a parabolically accelerated vertical plate was examined in the present article along with the transfer of the heat & mass in the incidence of thermal radiation. The inverse Laplace method is used to resolve the dimensionless equations. The concentration and temperature fields, axial and transverse velocity are examined for distinct parameters like the (Casson fluid), Sc (Schmidt number), Gr (thermal Grashof number), Pr (Prandtl number), and Gm (mass Grashof number). Utilizing the temperature of fluid and concentration of species as a solution is also proposed. Graphical representations of the fluctuations in temperature of fluid and velocity along species concentration are provided for several values of relevant flow parameters.

The Role of TNF-Alpha in the Wound Healing Process: Molecular and Clinical Perspectives - A Systematic Literature Review

Wounds are conditions of damage and partial loss of body tissue caused by physical trauma, sharp objects, blunt objects, temperature fluctuations, chemical exposure. Wound healing is a complex interaction between cells, cytokines, mediators, and blood vessels as a natural physiological response to tissue damage. TNF-α has a crucial role in the wound healing process, facilitating body immunity, immune cell mobilization, fibroblast cell proliferation, keratinocytes, and growth factor expression. Although TNF-alpha has benefits in the early stages of wound healing, excessively high levels or a sustained inflammatory response can lead to problems, such as excessive scar tissue formation or blockages, which can impede the wound healing process. This study utilized the PRISMA-ScR (Scoping Review) protocol. A review was conducted of articles discussing the Role of TNF-Alpha in the Wound Healing Process: Molecular and Clinical Perspectives within the last 10 years. Literature search in this study using PubMed, ScienceDirect, Elsivier and Google Scolar databases Search using English, abstract and full text. After searching with the keywords: The Role of TNF-Alpha, 19,022 articles were found. The search continued using the keyword The Role of TNF-Alpha in the Wound Healing found 346 articles. The last search using the keyword The Role of TNF-Alpha in the Wound Healing: Molecular and Clinical found 26 articles. TNF-α plays an important role in the early stages of cutaneous wound healing, significantly delayed after day 3, but not by day 7. TNF-α has a crucial role in the early stages of skin wound healing, and its administration is recognized to have a positive impact on the healing response, which may pave the way for innovative strategies to address chronic skin wound healing problems.

Thermal insulation box design for maintaining cool temperature and the postharvest quality of okra

Postharvest loss of okra is caused by its high respiration rate and temperature fluctuations in the supply chain. To address this, five thermal insulation boxes were designed, combining different materials, and evaluated for okra quality during simulated transportation and storage. The treatments included the standard foam box, metalized foam sheet (two layers consisting of aluminum foil and expanded polyethylene), prototype-A (three layers consisting of dual layer of aluminum foil and expanded polyethylene), prototype-B (four layers consisting of aluminum foil, nonwoven, expanded polyethylene, and aluminum foil), and standard regular slotted container. Material tests revealed that aluminum foil and expanded polyethylene had the lowest thermal heat energy. The composite sandwich box design, prototype-A, demonstrated the highest maximum insulation time of 28 h and thermal resistance of 0.332 m2°C/W. Prototype-A and prototype-B effectively maintained low temperature fluctuation, minimized air and okra temperature changes, and maintained 6.19 to 8.25 % CO2, which was within an acceptable range of 4–10 % for okra. Both prototypes exhibited reduced percentage mass loss in okra below 5 %. Importantly, both prototypes demonstrated the lowest incidence of okra pod surface browning and maintained the quality for 6 d, surpassing metalized foam sheet and standard regular slotted container. These findings offer sandwich design with 3 or 4 layers as promising alternatives for thermal insulation boxes in cold chain management, enhancing the transport packaging of okra under ambient environments compared to the standard foam box.

Construction alignment and closure control of CFST truss arch bridges based on temperature effect

To reveal the temperature deformation laws and achieve the accurate alignment prediction during the installation process of long-span concrete-filled steel tubular arch bridge ribs in complex environments, this paper establishes a three-dimensional refined heat transfer model for temperature field and effect calculation of truss arch ribs. The model uses the Ray Tracing Technology to recognize the member-caused-shading area on arch ribs. And by comparing with the actual measurement results and shadow effects to achieve the accurate calculation of temperature field. Finally, the variation of ribs deformation during construction and the optimal closure time are detailed analyzed. Results show that the computational method used in this paper can achieve accurate recognition of shadows and precise calculation of the complex three-dimensional temperature field of truss arch ribs. After considering the shadows, the maximum temperature difference between the upper chord sunshine area and lower chord shadow areas can reach 25 °C, which is significantly greater than 8 ℃ in the "Specifications for design of highway concrete-filled steel tubular arch bridge" (JTG/T D65–06-2015). Due to the solar incidence variation along the longitudinal direction of the arch ribs, extreme temperature fluctuation of the chord tubes occurs, with a maximum temperature difference of 21 °C. When arch ribs reach the maximum cantilever, the daily vertical displacement variation can reach approximately 87 mm, and the maximum displacement difference between arch ribs of two canyon sides can reach 15.6 mm at the same time. The solar-caused maximum compressive stress is 34 MPa, which can exceed 100 MPa after superimposing the gravity and cable effects. Based on the analysis of the displacement of both sides of the closure joint under the influence of sunlight, this paper identifies the window period for the closure control of the long-span steel truss arch ribs, laying the foundation for the accurate control of the rib construction alignment and the closure internal force state.

Optimizing optical thermometry with tri-doped Ba2GdV3O11 phosphors: Ratiometric and fluorescence lifetime analysis

Optical sensor technology has undergone a transformative evolution with the advent of fluorescence ratio techniques (FIR) and fluorescence lifetime (FL) strategies, revolutionizing precision, performance, and reliability. This study delves into the synthesis of Ba2GdV3O11 phosphors doped with Ho3+/Nd3+, Er3+, and Yb3+, employing the sol-gel method for upconverting material fabrication. A thorough investigation into the structural, morphological, and optical properties of the synthesized phosphors is conducted. Excitation at 980 nm unveils upconversion (UC) emissions across green and red spectra. The intensities of the observed emission bands for Ho3+, Nd3+, and Er3+ demonstrate significant sensitivity to fluctuations in temperature. Temperature sensing relies on the 4S3/2 and 2H11/2 upconversion emissions bands, in addition to the emission lifetimes at 4S3/2. Enhanced thermal sensitivity values are attained, reaching up to 1.03 % K−1 and 1.07 % K−1 using the FIR strategy, and up to 0.146 % K−1 and 0.47 % K−1 with the FL strategy for Ho3+/Er3+/Yb3+ and Nd3+/Er3+/Yb3+ tri-doped Ba2GdV3O11 phosphors, respectively. Furthermore, the studied phosphors exhibit remarkable precision in detecting minute temperature changes (0.3 K), positioning them as promising candidates for precise temperature sensing. This study pioneers innovative methodologies to advance optical thermometry techniques, offering promising prospects for scientific and industrial applications reliant on precise optical temperature sensing.

Ultra-Low Power 9T FinFET Based SRAM Cell for IoT Applications

The rapid proliferation of Internet of Things (IoT) devices has escalated the demand for energy-efficient memory solutions. The development of SRAM (Static Random-Access Memory) has gathered significant attention, particularly for low-power applications and portable devices. This research introduces a novel approach to ensure robust performance and operational integrity, all while adhering to stringent power constraints amidst process and temperature fluctuations. This quest for alternative nano-devices has been ignited by the scaling and channel control challenges intrinsic to CMOS technology. Among the array of alternatives, including FinFETs, TFETs, and CNTFETs, FinFETs have emerged as strong contenders. FinFET SRAMs contribute to the ongoing drive for electronic devices to become more compact and energy-efficient. They offer a distinct advantage as a promising CMOS substitute, attributed to their high performance, stability, with low power consumption characteristics at the nanoscale. The study proposes an ultra-low power 9T FinFET based SRAM cell meticulously designed for IoT applications. Leveraging the unique attributes of FinFET based 9T cell, the proposed SRAM cell is tailored to achieving minimal power consumption while maintaining inherent stability. The study assesses the performance of the proposed SRAM cells for power dissipation, stability, speed, and energy efficiency, and compares them with existing SRAM structures. The results are obtained through the Monte Carlo simulation technique, which evaluates circuit performance under specified conditions. The study achieves remarkable efficiency gains with 9T SRAM cells compared to other configurations. Additionally, the reduced read and write access times facilitate expedited data retrieval and storage operations.

The Impact of In-Flight Acceleration Environments on the Performance of a Phase-Change Heat Exchanger Unit with Layered Porous Media

The Phase-Change Heat Exchanger Unit in Layered Porous Media (PCEU-LPM) is obtained through frozen pouring processing, and exhibits characteristics such as high thermal conductivity, high latent heat, and high permeability, making it suitable for dissipating heat in airborne electronic devices. This study numerically investigates the impact of aircraft speed acceleration conditions, which lead to weightlessness or overload, on the performance of the PCHEU-LPM, with a particular focus on the influence of natural convection in the liquid-phase region. Initially, a microscale thermal analysis model is established based on the Navier–Stokes equation scanning electron micrograph to calculate the effective thermal conductivity and permeability of the PCHEU-LPM under different porosities. Subsequently, these parameters are incorporated into a macroscale thermal analysis model based on Darcy’s law, employing an average parameter approach. Using the macroscale thermal analysis model, temperature and velocity fields are computed under various porosities, acceleration magnitudes, and directions. The calculation results indicate that as the acceleration increases from α = 0 to α = 10 g, the interface temperature of the PCHTU-LPM decreases by approximately 5.2 K, and the temperature fluctuation decreases by 2.4 K. If the porosity of the PCHTU-LPM is increased from ε = 70% to ε = 85%, the influence of acceleration change on natural convection will be further amplified, resulting in a decrease in the interface temperature of the PCHTU-LPM by approximately 10.2 K and a decrease in temperature fluctuation by 5.8 K. When the acceleration direction is +z, the interface temperature of the PCHTU-LPM is at its lowest, while it is highest when the acceleration direction is −z, with a maximum difference of 15.4 K between the two. When the acceleration direction is ±x and ±y, the interface temperature lies between the former two cases, with the interface temperature slightly higher for ±y compared to ±x, with a maximum difference of 3.9 K between them.

The Influence of Solar Irradiance and Temperature on The Pll-Synchronized Inverter Within Grid-Connected PV Systems

This study assesses the influence of solar irradiance and temperature on αβPLL synchronized inverters by investigating their intricate relationship within grid-connected PV systems. The intermittent nature of the DC side of these systems can significantly impact their performance. However, the extent of this impact remains uncertain when employing the stationary reference frame PLL (αβPLL) algorithm for synchronization with the utility grid. Employing simulation in MATLAB 2020a and a Model Based Design approach in the Simscape toolbox of SIMULINK, we conducted this investigation through two test scenarios: one with constant solar irradiance and varying temperature, and the other with varying solar irradiance and constant temperature. Our results indicate that fluctuations in solar irradiance and temperature have minimal effects on the output parameters of grid-connected PV systems when synchronized with the stationary reference frame PLL (αβPLL) algorithm. This conclusion is supported by the total harmonic distortion values, which all fall within the specified limits of IEEE Standard 929- 2000. These findings underscore the potential of αßPLL synchronization as a promising technique, capable of effectively synchronizing grid inverters even in the presence of DC input distortion. This proficiency in grid integration holds promise for enhancing the integration of renewable energy sources into the grid, thereby bolstering power availability for household distribution.

Absolute instability of moisture‐coupled waves on the equatorial beta‐plane

AbstractThe instabilities produced by a linear model of the tropical atmosphere coupled to a prognostic equation for water vapour are investigated. The basic model with no meridional wind supports unstable eastward‐propagating waves. For parameter regimes relevant to the Indo‐Pacific warm pool, the long‐time asymptotic behaviour of the unstable waves is found to be absolutely unstable, so that the amplitude of disturbances will grow in time at every point in the domain. The absolute instability of the system is realized at planetary length‐scales and intraseasonal frequencies. Other parameter choices for the system do not produce this same behaviour at these length‐ and time‐scales. It is shown that the resultant long‐time behaviour of the instability is characterized by roughly equal roles for temperature and moisture fluctuations in setting the thermodynamic tendency of the waves. With the inclusion of momentum damping, the phase speed of the absolutely unstable solution is about 7 ms. Addition of a strong background meridional moisture gradient, as in recent studies on the Madden–Julian Oscillation (MJO), appears to remove the absolute instability from the system. In a background state that varies slowly in the zonal direction, it is shown analytically that localized regions of instability may be formed, again using parameter choices relevant to the warm pool. The dynamics and thermodynamics of these local instabilities show some correspondence with the observed development of the MJO as it propagates through the warm pool.