Prefix Adders Research Articles

Energy-efficient design and CNFET implementation of GDI-based ternary prefix adders

Abstract Ternary adders have produced more benefits compared to binary adders i.e., the ternary adder occupies less amount of area as well as produces less interconnect complexity. However, the CMOS implementation of the ternary adders failed to perform the process when the channel length was taken as 32 nm. At 32 nm technology, the CMOS transistors exhibit undesired effects such as Short Channel Effects (SCEs), mobility degradation, high leakage current, etc. Multi-gate devices are preferred to overcome these issues. Carbon Nano-tube Field Effect Transistors (CNFETs) are one of the technologies to work efficiently when the channel length is 32 nm. In this paper, CNFET-based ternary prefix adders are designed. Power consumption is the most critical requirement for the VLSI system, as it enhances energy efficiency and reduces heat dissipation. One way to achieve this power reduction is by minimizing the number of transistors employed in the adder circuits. This study employed a reduction technique known as Gate Diffusion Input (GDI) logic included in the proposed prefix adder design. The overall experimental investigation is done with the help of the HSPICE supporting platform. The proposed adder improved by reducing the power by up to 83%, energy by up to 83%, current by up to 78%, and delay by up to 96%. Finally, the Power Delay product (PDP) was also reduced by 84% compared to existing ternary adders. The proposed design proves to be highly effective in implementing the neuron structure, with the corresponding parameters thoroughly analysed and well-documented in this study.

Optimized power and speed of Split-Radix, Radix-4 and Radix-2 FFT structures

Fast Fourier transform (FFT) is a fundamental building block for digital signal processing applications where high processing speed is crucial. Resource utilization in implementing FFT structures can be minimized by optimizing the performance of multipliers and adders used within the design. FFTs are also widely used in various machine learning algorithms. To achieve increased processor efficiency and reduced resource utilization, we propose a hardware design for Radix-2, Radix-4, and Split-Radix FFT architectures that utilizes a novel parallel prefix adder. This design offers lower power consumption, smaller chip area, and faster operation compared to existing architectures. Our performance analysis focuses on metrics such as power consumption, clock speed, and hardware complexity for Radix-2, Radix-4, and Split-Radix FFT algorithms implemented with the proposed adder. We compare these metrics using our proposed arithmetic structure against existing adder designs. The results indicate that the Split-Radix FFT architecture achieves lower power consumption and smaller chip area compared to Radix-4 and Radix-2 methods. Additionally, the Split-Radix FFT exhibits a higher clock speed. Therefore, based on these findings, the Split-Radix algorithm appears to be a compelling choice for implementation on field-programmable gate arrays due to its high speed and lower power consumption.

APPAs: fast and efficient approximate parallel prefix adders and multipliers

APPAs: fast and efficient approximate parallel prefix adders and multipliers

Area-Delay-Power Efficient VLSI Architecture 2D FIR Filter using Modified Multipliers and Adders

In this paper, a low power, area, and delay 2D Finite Impulse Response (FIR) filter architecture is derived from an analysis of a memory-efficient design. The completely direct-form 2D FIR filter is where the idea of parallel processing is first presented. As a result, the FIR filter may make better use of its memory by reusing its contents. With a block size of L and a filter length of N, a non-separable 2D FIR filter structure is developed and implemented. The FIR filter's arithmetic module makes use of high-speed, low-power multipliers and Carry Look Ahead (CLA) adders, with the output calculated by a pipelined adder unit. Verilog HDL code is used to represent the proposed architecture, and the CADENCE environment's NC Simulator and RTL Compiler synthesis tool are used to verify the design. Existing memory-efficient 2D FIR filter hardware architectures are compared to the produced area, power, and delay reports. Using Modified CLA (MCLA) adders and pipelining, we were able to cut down on power consumption by 44% and delay by 20%. Index Terms: Memory reuse, 2D-FIR filter, Low Power Multiplier, Parallel Prefix Adder, Carry Look Ahead adder, and pipelining.

Performance Analysis of Approximate Parallel Prefix Adders Realized with Field-programmable Gate Array Technology

Introduction: Parallel prefix adders are widely used in high-speed arithmetic circuits due to their ability to perform additions in logarithmic time. However, the high area and delay of exact parallel prefix adders prompted the development of approximate parallel prefix adders. These adders are a promising solution for high-speed arithmetic circuits because they sacrifice accuracy for reduced area and delay. Methods: This paper presents a performance analysis of five approximate parallel prefix adders realized with field programmable gate array technology. The five approximate parallel prefix adders are the Kogge-Stone adder, the Sklansky adder, the Brent-Kung adder, the Han-Carlson adder, and the Ladner-Fisher. Each adder is implemented in a Xilinx Artix-7 FPGA. The area and delay of five approximate parallel prefix adders are evaluated. The Kogge-Stone approximate parallel prefix adder, out of five approximate parallel prefix adders, consumes the least delay, irrespective of the number of bits. Results: The Sklansky approximate parallel prefix adder out of five approximate parallel prefix adders consumes the least area irrespective of the number of bits in addition. Overall, our research sheds light on the trade-offs between area, power delay, and power delay products of five approximate parallel prefix adders implemented with FPGA technology. Conclusion: This analysis can help choose the best approximate parallel prefix adder for specific high-speed arithmetic applications. In the case of 16- and 32-bit five approximate parallel prefix adders, Ladner-fisher shows the best power delay product, whereas 64- and 128-bit five approximate parallel prefix adders, Sklansky adder shows the best power delay product.

Comparative Analysis of Dynamic Power Consumption of Parallel Prefix Adder

The Newcomb-Benford law, also known as Benford's law, is the law of anomalous numbers stating that in many real-life numerical datasets, including physical and statistical ones, numbers have a small initial digit. Numbers irregularity observed in nature leads to the question, is the arithmetical-logical unit, responsible for performing calculations in computers, optimal? Are there other architectures, not as regular as commonly used Parallel Prefix Adders, that can perform better, especially when operating on the datasets that are not purely random, but irregular? In this article, structures of a propagate-generate tree are compared including regular and irregular configurations—various structures are examined: regular, irregular, with gray cells only, with both gray and black, and with higher valency cells. Performance is evaluated in terms of energy consumption. The evaluation was performed using the extended power model of static CMOS gates. The model is based on changes of vectors, naturally taking into account spatio-temporal correlations. The energy parameters of the designed cells were calculated on the basis of electrical (Spice) simulation. Designs and simulations were done in the Cadence environment and calculations of the power dissipation were performed in MATLAB. The results clearly show that there are PPA structures that perform much better for a specific type of numerical data. Negligent design can lead to an increase greater than two times of power consumption. The novel architectures of PPA described in this work might find practical applications in specialized adders dealing with numerical datasets, such as, for example, sine functions commonly used in digital signal processing.

DESIGN AND ANALYSIS OF NOVEL PARALLEL PREFIX ADDERS FOR VLSI CIRCUITS

Arithmetic Logic Unit is the brain of all processors, is composed of an Adder circuit. The main component of multiplier circuits is the adder, which performs subtraction (by 2’s complement arithmetic). Since the most fundamental operation in mathematics is addition, and the adder is the most essential part of the processor, the study of VLSI arithmetic has required many digital VLSI researchers. When designing digital systems employing the VLSI approach, the digital adder plays a major role. Low power VLSI based adder designs perform poorly because of the propagation delay issue. With the aid of the PPA design, an assessment of adders’ availability for low power VLSI designs with minimal propagation delay is conducted. Using these performance measures, this study compares and evaluates the performance of several parallel prefix adders, allowing readers to select the optimum adder architecture for their application Specific Integrated Circuits implementations. The three adder topologies taken into considered in this Article include the Han carlson adder, Brent kung, Kogge stone adders. Xilinx ZYNQ XC7Z020 (7000 series) SoC is used to implement the adders using the Vivado Design Suite 2014 and Verilog.

Design and Comparison of 24-bit Three Operand Adders using Parallel Prefix method for Efficient Computations

Binary Three-operand adder serves as a foundation block used within security and Pseudo Random-Bit Generator (PRBG) systems. Binary Three-operand adder was designed using Carry Save Adder but this consumes more delay. Therefore, a Parallel Prefix Adder (PPA) method can be utilized for faster operation. The canonical types of PPA result in a lesser path delay of approximately O (log2 n). These adders can be designed for 8, 16, 24 or n bits. But this work is focused on developing a 24-bit three-operand adder that takes three 24-bit binary numbers as input and generates a 24-bit sum output and a carry using five different PPA methods The proposed summing circuits are operationalized with Hardware-Description-Language (HDL) using Verilog, and then subjected to synthesis using Field -Programmable Gate- Array (FPGA) Vertex 5. On comparing the proposed adders, it shows that the delay and the size occupied are significantly less in the Sklansky PPA. These faster three-operand adders can be utilized for three-operand multiplication in image processing applications and Internet of Things (IoT) security systems.

Demonstration of a novel majority logic in a memristive crossbar array for in-memory parallel computing.

A memristive crossbar array can execute Boolean logic operations directly within the memory, which is highly noteworthy as it addresses the data bottleneck issue in traditional von Neumann computing. Although its potential has been widely demonstrated, achieving practical levels of operational reliability and computational efficiency remains a challenge. Here, we introduce a three-input majority logic gate supported by near-memory operations, serving as a universal gate and achieving both robust reliability and high efficiency in versatile logic operations. We fabricated a highly reliable HfOx-based memristive array, incorporating a series resistor to increase the reset voltage of the memristor, thereby increasing the operational voltage margin of the gate operation. This ensured reliable operation of the majority gate, resulting in successful experimental proof of combined 1-bit full adder and subtractor operations performed in 5 steps using 7 cells. Additionally, we propose that an N-bit parallel prefix adder (PPA) operation is possible in O(log2 N) steps, by taking advantage of the parallel operation capability of the majority gate. This achieves 8.5× higher spatiotemporal efficiency than the previously reported NOR-based logic system in 64-bit adder operation. Moreover, as N increases, the spatiotemporal efficiency further improves, which significantly enhances the applicability of memristive logic-in-memory.

Analysis of Parallel Prefix Adders

Abstract: Parallel prefix adders are essential components of contemporary digital arithmetic circuits and are found in many different devices, including digital signal processors and microprocessors. In order to improve the effectiveness and performance of parallel prefix adders, this research investigates their design and optimization. This paper analyses in detail the state of the parallel prefix adder architectures and provide new designs that minimize power consumption and critical path delays. The speed and area efficiency benefits of the parallel prefix designs with thorough simulations and comparisons is reviewed. This research have ramifications for high-performance computing systems and point to interesting avenues to further the state of the art in parallel prefix adder design.

An Efficient Design of a Parallel Prefix Adder based on QCA Technology

This paper presents an optimized Parallel Prefix Adders (PPA) based on Quantum dot Cellular Automata (QCA) technology. PPA presents the most used block in Arithmetic Logic Units (ALU) which presents a fundamental part in several digital integrated circuits. The classical implementation method of PPA based on traditional Complementary Metal Oxide Semiconductor (CMOS) Technology presents several problems in terms of frequency, power consumption, surface and others. The QCA technology offers several features such as ultralow power consumption, small size, and can operate up to 1 THz. In this work, a 4-bit Parallel Prefix Adder with a new prefix low area and high speed is proposed. The proposed design is based on a half-adder circuit and other logic gates. These designs were tested and simulated using the freely known QCA Designer Tool version 2.0.3. and QCA pro. The proposed Half-adder presents a reduction of 23% 46% and 36% in terms of cell count, latency and power consumption, respectively compared to existing designs. The proposed PPA design shows almost an optimization of 5% in area and 58% in latency compared to the RCA design. The proposed circuit present an optimization of 20% in term of energy consumption compared to the existing PPA 4-bit Brent Kung Adder design.

Design and Implementation of RISC-V Based Pipelined Multiplier

Among the many microprocessors, RISC-V as an open-source instruction set is gradually gaining popularity among academia and industry. The performance of the multiplier in the microprocessor imposes constraints on the computational power of the processor. In order to improve the efficiency of multiplication instructions, a pipeline multiplier is implemented in this paper. Firstly, the partial product is generated using the Radix-4 booth. Secondly, the Wallace tree structure is used to accelerate the compression of the partial product. Then, a parallel prefix adder is used to calculate the resulting partial product to improve the timing. Finally, registers are added as a pipeline to achieve a high-efficiency multiplication calculation. With the operating voltage and temperature set to typical conditions, the integrated multiplier area is 50260.6 μm2, and the power consumption is 20.41 mW. The final frequency of the multiplier is 1 GHz in gate-level simulation.

A Parallel Prefix Modulo-(2 q + 2 q−1 + 1) Adder via Diminished-1 Representation of Residues

Diminished-1 representation of modulo-(2q+1) residues provides for delay-balanced adders for the popular moduli set τ=2q+2q±1. Besides, conjugacy of moduli 2q±1 leads to efficient multiple-residue to binary conversion. Nevertheless, cardinality of τ does not cover the required dynamic range of some applications that also require small q-values for gaining the desired arithmetic speed (e.g., convolutional neural networks). The recently proposed parallel prefix modulo-(2q+2q-1-1) addition scheme provides for balanced performance with similar adder architectures for the moduli of doubly-wide τ (i.e., τ2q+22q±1). Should there be a compatible adder for the conjugate modulo 2q+2q-1+1, the new moduli set τ+2=22q,22q±1,2q+2q-1±1 can provide more than (8q-3) bits of dynamic range, with equally fast adders as those of τ2, whose dynamic range is only 6q bits. Therefore, we were motivated to propose the new modulo 2q+2q-1+1 and its equally fast parallel prefix adder with compatible cost as of its conjugate modulo. This is actually achieved via diminished-1 representation of residues, where those in 1,2q+2q-1 are encoded as 0,2q+2q-1-1 and a zero indicator bit is set for 0-valued residues. The VLSI simulation and synthesis results, especially for the common cases of q=2p, confirm the analytical evaluations regarding the balanced performance of the conjugate moduli 2q+2q-1±1.

High Performance, Low Power Wallace Tree Multiplier

An area-efficient high Wallace tree multiplier using adders is presented in this paper. The proposed Wallace tree multiplier is designed using logic gates and adders. The design is implemented in Cadence Virtuoso using a 45-nm technology library. The proposed design offers reduced delay and higher performance than conventional multipliers using carry-save adders with majority-based gate adder logic. The design also offers a reduced transistor count of 12, which is minimal compared to that of the conventional design. One of the fundamental building blocks of many VLSI applications is multipliers. To enhance the performance of circuits and systems, the design of multipliers is very important. The key feature of a high-performance Wallace tree multiplier lies in its efficient reduction of partial product additions. By utilising a combination of carry-save and carry-propagate adders, it minimises the critical path delay and maximises the speed of multiplication. Additionally, advanced optimisation techniques such as parallel prefix adders and parallel carry-save adders can be employed to further improve performance.

Area & power modeling for different tree topologies of parallel prefix adders

Parallel prefix adder (PPA) being an indispensable component of processors needs prompt estimation of design metrics at the initial stage of design cycle. However, the available commercial tools take significant amount of time for the estimation process. The prior availability of area and power models can greatly reduce time-to-market. Symmetrical construction and quick computational ability of PPAs make them competent candidates for adder circuits in complex applications. This paper proposes area and power models for Field Programmable Gate Arrays (FPGA) implementation of classic PPAs, targeted to Xilinx Zynq-7000 family. The available literature barely presents parameters estimation and their analysis for PPAs. Therefore, modeling proposed in this paper is a novel work. PPA structures are simulated, synthesized and implemented using commercial tool i.e. VIVADO IDE. Models have been developed using curve fitting and validated against commercial tool. Results show an average estimation error ranging from 0.37% to 1.34% in case of area modeling and 0.23% to 0.59% in case of power modeling which are comparable with state of the art.

A Novel High Computing Power Efficient VLSI Architectures of Three Operand Binary Adders

Directly or indirectly adders are the basic elements in almost all digital circuits, three operand adders are the basic building blocks in LCG (Linear congruential generator) based pseudo-random bit generators. Elementary adders are fast, area and power efficient for small bit sizes. Carry save adder computes the addition in O(n) time complexity, due to its ripple carry stage. Parallel prefix adders such as Han-Carlson compute the addition in O(log(n)) time complexity but at the cost of additional circuitry. Hence new high-speed power-efficient adder architecture is proposed which uses four stages to compute the addition, which consumes less power, and the adder delay decreases to O(n/2). Even though it is not much faster than the High-speed Area efficient VLSI architecture of three operand adders (HSAT3), it computes the addition by utilizing less power. The proposed architecture is implemented using Verilog HDL in Xilinx 14.7 design environment and it is evident that this adder architecture is 2 times faster than the carry save adder and 1, 1.5, 1.75 times faster than the hybrid adder structure for 32, 64, 128 bits respectively. Also, power utilization is 1.95 times lesser than HSAT3, 1.94 times lesser than the Han-Carlson adder, and achieves the lowest PDP than the existing three operand techniques.

Delay-Optimistic Multiplier Design using Parallel Prefix Adder with Compressors

This article provides an illustration of the design process for 5-2 and 7-2 compressors operating at extremely high speeds. When compared to the prior designs, the new approach significantly reduced the gate-level delay while maintaining an appropriate overall transistor and gate count. With the help of 7:2 and 5:2 compressor infusion, when compared to earlier designs, the gate-level latency has been significantly decreased while the overall transistor and gate counts have remained within acceptable bounds. The technique was created for the 5-2 compressor and expanded for the 7-2 design, which exhibits higher speed performance enhancement for these architectures. To increase performance in terms of latency, we can switch out the ripple carry adder at the last addition for a parallel prefix adder. In addition, careful design considerations were taken to keep other factors, such as power and activity, within reasonable bounds. The best-reported circuits have also undergone redesigns, and the parasitic components of those circuits have been eliminated using the same method to produce a fair comparison. Using a common 16 × 16-bit multiplier, the performance of the built compressor blocks has also been assessed.

Design of novel high speed parallel prefix adder

Adders are crucial logical building blocks found almost in all the modern electronic system designs. In the adder architecture design, the fundamental issue is the propagation latency in the carry chain. As the length of the input operands increases, the length of the carry chain along with it. Parallel prefix adders, which address the problem of carry propagation in adders, are the most efficient adder topologies for hardware implementation. However, delay reduction still could be achieved for very high speed applications. Hence, in this paper design of 16bit novel parallel prefix adder is proposed and compared against the existing parallel prefix adder architectures. The design and simulation are carried out using xilinx vivado for field- programmable gate array (FPGA) simulation and Cadence® for ASIC. The results of ASIC implementation demonstrate 17.8% delay reduction while compared to sparse kogge-stone adder.

AxPPA: Approximate Parallel Prefix Adders

Addition units are widely used in many computational kernels of several error-tolerant applications such as machine learning and signal, image, and video processing. Besides their use as stand-alone, additions are essential building blocks for other math operations such as subtraction, comparison, multiplication, squaring, and division. The parallel prefix adders (PPAs) is among the fastest adders. It represents a parallel prefix graph consisting of the carry operator nodes, called prefix operators (POs). The PPAs, in particular, are among the fastest adders because they optimize the parallelization of the carry generation ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$G$ </tex-math></inline-formula> ) and propagation ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$P$ </tex-math></inline-formula> ). In this work, we introduce approximate PPAs (AxPPAs) by exploiting approximations in the POs. To evaluate our proposal for approximate POs (AxPOs), we generate the following AxPPAs, consisting of a set of four PPAs: approximate Brent–Kung (AxPPA-BK), approximate Kogge–Stone (AxPPA-KS), Ladner-Fischer (AxPPA-LF), and Sklansky (AxPPA-SK). We compare four AxPPA architectures with energy-efficient approximate adders (AxAs) [i.e., Copy, error-tolerant adder I (ETAI), lower-part OR adder (LOA), and Truncation (trunc)]. We tested them generically in stand-alone cases and embedded them in two important signal processing application kernels: a sum of squared differences (SSDs) video accelerator and a finite impulse response (FIR) filter kernel. The AxPPA-LF provides a new Pareto front in both energy-quality and area-quality results compared to state-of-the-art energy-efficient AxAs.

Implementation of low power N-bit hybrid parallel prefix adder using Xilinx-ISE

Recently, digital circuitry has demanded a decrease in space and power by decreasing time while simultaneously improving performance in speed. This has resulted in a need for more efficient use of the available space. Adders are fundamental components that are used in the construction of digital circuits. As a consequence of this, the performance of adders has to be improved in order to enhance the performance of integrated circuits that are used in the real world. The creation of a novel parallel prefix adder (PPA) architecture known as Hybrid PPA is the primary topic of this article. Hybrid PPA makes use of full carrier generation (FCG), full sum generation (FSG), half carry generation (HCG), and half sum generation (HSG) blocks. In addition to this, the N-bit Hybrid-PPA is constructed with features that may be reconfigured, and these features utilise square root additions through modified sum carry selection (MSCS). In addition, the implementation of multiplexer switching logic, which selects the whole sum bits and carry bits in a high-speed manner, reduces the amount of propagation time necessary for the generation of the sum and carry output. The results of the simulation show that using the proposed Hybrid PPA results in a reduction in area, latency, and power consumption when compared to using basic adders or approaches that are considered to be state of the art.