Types Of Particles Research Articles

Organic-inorganic core-shell materials as reinforced fillers of UHMWPE to improve its tribological and mechanical properties

Generally, modification of materials by adding multiple types of nano particles could cause dispersion problems, generally limited the performance improvement effect. Herein, we report the modification of UHMWPE materials by organic-inorganic core-shell particles with PTFE as the core and Al(OH)3 as the shell, which prepared by in-situ polymerization of sodium bicarbonate and aluminum sulfate solution. Core-shell particles were filled in UHMWPE matrix and sintered into composite by spark plasma sintering (SPS). The mechanical and tribological properties of the composites were characterized by tensile compression testing machine, universal micro tribometer (UMT-5), three-dimensional white light interferometer and scanning electron microscope (SEM). The results showed that the addition of core-shell structural materials effectively improved the tribological properties (friction coefficient decreased by 40%, wear rate decreased by 30%) and mechanical properties (compression strength increased by 2.4 times) of the composites. It was demonstrated that the inorganic framework provided strength to improve the mechanical properties and wear resistance of materials, and the organic phase was used as a lubricating phase to reduce the friction coefficient of materials. Surface treatment of core-shell particles both improved the binding between particles and matrix and decreased the formation of agglomerations, thus significantly reducing ploughing phenomena’s effect produced by abrasive wear of agglomeration

Effect of co-combustion of coal with biomass on the morphology of soot

This study performed an experimental investigation to explore the effect of co-combustion of coal with biomass on the morphological parameters and nanostructure of soot. Three types of soot, namely Shenghua coal (SH) soot, Pinewood biomass (PW) soot, and Co-combustion of SH and PW (CC) soot, were collected from the combustion flames of Shenhua coal, Pinewood biomass, and a mixture of coal and biomass. Thereafter, the soot samples were observed and analyzed by means of transmission electron microscope (TEM) and scanning electron microscope (SEM) to obtain their morphological parameters and nanostructure characteristics. The TEM results showed that the size of nascent soot particles generated in co-combustion flame is the largest, rather than between the sizes of PW and SH soot. The nanostructure of the three types of soot primary particles is mainly composed of straight parallel crystal stripes. The separation distance of crystal stripes in SH soot was measured to be larger than that in PW soot, indicating that the crystal structure of soot generated in Pine biomass combustion flame is more compact. It was also observed that both coal-derived primary soot particles and biomass-derived primary soot particles were formed in the co-combustion flame. SEM results indicated that PW soot agglomerates have stronger aggregation performance and more compact structure then SH soot and CC soot. The primary particle size of SH and CC soot agglomerates was mainly concentrated between 50 and 70 nm, while that of PW soot agglomerates was relatively uniform. Furthermore, the number of primary particles in SH soot and CC soot was distributed over a wide range compared to PW soot.

Measurements of the inherent optical properties of aqueous suspensions of microplastics

AbstractLibraries of inherent optical properties (IOPs) of microplastics are sparse, yet they are essential for the development of optical techniques to detect and quantify microplastics in the ocean. In this study, we describe our results and technique for the measurement of the IOPs of microplastic suspensions generated from commonly utilized plastics. The measurements included angle‐resolved polarized light scattering, and spectral absorption and beam attenuation coefficients. We also performed ancillary characterization of particle properties, including size distribution, shape, and mass concentration of suspended matter. We observed several unique optical characteristics regarding absorption, scattering, and polarization properties compared with typical marine particle assemblages. We show that these results are useful for radiative transfer simulations as well as the potential development of novel plastic detection techniques from above‐ or in‐water optical measurements.

Fate and behaviour of Microplastics (> 25µm) within the water distribution network, from water treatment works to service reservoirs and customer taps

Water treatment works have previously shown high efficiency in removing microplastics > 25 µm from raw source water. However, what is less well known is the extent to which microplastics of this size class are generated or lost within the water distribution network, particularly whether there is a greater presence in the customer tap than in the water treatment works outlet. This study focused on the presence of 21 different types of synthetic polymer particles with sizes larger than 25 µm examined through multiple rounds of sampling at outlets of water treatment works (WTW), service reservoirs (SR), and customer taps (CT) managed by seven different water companies in Britain. Nineteen different types of polymers were detected; their signature and concentration varied based on the round of sampling, the location within the water supply network, and the water company responsible for managing the supply. Among the polymers examined, polyamide (PA), polyethene terephthalate (PET), polypropylene (PP), and polystyrene (PS) were the most commonly found. Apart from PET having its highest concentration of 0.0189 microplastic per litre (MP/L) in the SR, the concentrations of the other three most frequent polymers (PS = 0.017 MP/L, PA = 0.0752 MP/L, PP= 0.1513 MP/L) were highest in the CT. The overall prevalence of this size of microplastics in the network is low, but there was a high variability of polymer types and occurrences. These spatial and temporal variations suggested that the MP in the distribution network may exist as a series of pulses. Given the presence and polymer types, the potential for some of the microplastics to originate from materials used in the water network and domestic plumbing systems cannot be ruled out. As found before, the absolute number of microplastics in the water distribution network remained extremely low.

DEM analysis of flow dynamics of cohesive particles in a rotating drum

Cohesive particles, prevalent in chemical and metallurgical industries, necessitate a comprehensive investigation of their behavior. This study employs the discrete element method to predict the motion of two distinct types of cohesive particles within a three-dimensional rotating drum, with the evaluation of the influence of rotational speed on particle-level parameters, encompassing velocities, angular velocities, dispersion coefficients, and contact forces. The findings reveal that wet particles treated with a honey-additive exhibit heightened inter-particle bonding, resulting in flatter surfaces on inclined planes. Cohesive particles within the active region attain greater translational velocities than their counterparts within the passive region. The x-direction dispersion intensity of water-additive particles in both the active and passive regions increases from 2.41 × 10−4 m2/s and 9.99 × 10−5 m2/s to 5.75 × 10−4 m2/s and 3.34 × 10−4 m2/s, respectively, with the increase in rotational speed from 5.6 RPM to 11.6 RPM. Particles with a honey-additive demonstrate larger dispersion coefficients along the x- and y-axes, as well as higher velocities and contact forces, albeit lower angular velocities in contrast to particles treated with a water-additive. Furthermore, an escalation in rotational speed amplifies the dispersion coefficients and contact forces of the cohesive particles. The rotating kinetic energy of the particles with water-additive and honey-additive increases from 0.005 J and 0.01 J to 0.01 J and 0.045 J, respectively.

The effect of multi-scale second-phases on the microstructure evolution of a Mg–Al–Sn–Ca alloy during friction-stir processing

In the present work, the type, morphology and size of secondary phase particles in a Mg–4Al–2Sn-0.5Ca (ATX420) alloy are tailored through sub-rapid solidification (SRS) and aging treatment before friction stir processing (FSP) to systematically investigate their impact on microstructures and mechanical properties of the FSP ATX420 Mg alloy. The smaller eutectic CaMgSn phase with micro-defects in the as-cast SRS alloy is more likely to be broken during FSP, compared to the as-cast conventional solidification (CS) alloy. Additionally, nano-sized CaMgSn and Mg17Al12 particles precipitate in as-aged SRS alloy due to a high supersaturation solubility of solutes in the as-cast SRS alloy. These densely-distributed nano-sized precipitates in the as-aged SRS alloy increase the processing temperature by 60 °C during FSP, which results in less nano-sized precipitates in the stirring zone and grain growth of the α-Mg matrix. This leads to a decrease in hardness in the FSP-aged-SRS alloy (∼10 HV). Besides, the grain structure evolutions in the stirring zone and transition zone are systematically investigated for understanding the microstructure evolution during FSP in Mg alloys with eutectic phase.

How many microplastics do you need to (sub)sample?

Analysis of microplastics in the environment requires polymer characterization as a confirmation step for suspected microplastic particles found in a sample. Material characterization is costly and can take a long time per particle. When microplastic particle counts are high, many researchers cannot characterize every particle in their sample due to time or monetary constraints. Moreover, characterizing every particle in samples with high plastic particle counts is unnecessary for describing the sample properties. We propose an a priori approach to determine the number of suspected microplastic particles in a sample that should be randomly subsampled for characterization to accurately assess the polymer distribution in the environmental sample. The proposed equation is well-founded in statistics literature and was validated using published microplastic data and simulations for typical microplastic subsampling routines. We report values from the whole equation but also derive a simple way to calculate the necessary particle count for samples or subsamples by taking the error to the power of negative two. Assuming an error of 0.05 (5 %) with a confidence interval of 95 %, an unknown expected proportion, and a sample with many particles (> 100k), the minimum number of particles in a subsample should be 386 particles to accurately characterize the polymer distribution of the sample, given the particles are randomly characterized from the full population of suspected particles. Extending this equation to simultaneously estimate polymer, color, size, and morphology distributions reveals more particles (620) would be needed in the subsample to achieve the same high absolute error threshold for all properties. The above proposal for minimum subsample size also applies to the minimum count that should be present in samples to accurately characterize particle type presence and diversity in a given environmental compartment.

Fracture conductivity and rock appearance in volcanic reservoirs treated by various stimulation techniques

Volcanic reservoirs have complex mineral compositions and highly heterogeneous physical and mechanical properties, making their stimulation quite problematic. This study aimed at clarifying acid-rock reaction and stimulation mechanisms in volcanic reservoirs using 3D scanners and conductivity testing devices. Tests on rock sample conductivity and appearance under such mainstream stimulation technologies as hydraulic fracturing, acid fracturing, and proppant-carrying acid fracturing (PCAF) were performed. The effects of proppant particle size, proppant concentration, acid volume and type, proppant-carrying acid type, and proppant-carrying acid concentration on conductivity and rock sample appearance were analyzed. The appearance of rock samples included dot-, pit-, and strip-like embeddings, as well as acid-etching pits and channels. Larger particle sizes and higher proppant concentrations produced wider propped fractures and higher flow conductivity. Due to complex mineral distribution, acid fracturing failed to produce long etched channels, and the obtained conductivity was low, with a maximum of 8 D·cm at a 5 MPa closure stress. Hydraulic fracturing and PCAF reached a maximum flow conductivity of 155 D·cm at a 5 MPa closure stress, indicating their applicability to volcanic reservoir stimulation. This work helps reveal the acid-rock reaction and stimulation mechanisms of volcanic reservoirs and provides a theoretical basis for their development.

Plane Stress Problems for Isotropic Incompressible Hyperelastic Materials

The analysis of plane stress problems has long been a topic of interest in linear elasticity. The corresponding problem for non-linearly elastic materials is considered here within the context of homogeneous incompressible isotropic elasticity. It is shown that when the problem is posed in terms of the Cauchy stress, a semi-inverse approach must be employed to obtain the displacement of a typical particle. If however the general plane stress problem is formulated in terms of the Piola-Kirchhoff stress, the deformation of a particle requires the solution of a non-linear partial differential equation for both simple tension and simple shear, the trivial solution of which yields a homogeneous deformation. It is also shown that the general plane stress problem can be solved for the special case of the neo-Hookean material.

Influence of pH and salt solution on the sedimentation properties of fine bauxite tailings

Bauxite tailings slurry is a type of solid waste produced in the process of bauxite washing and beneficiation. It has poor engineering properties, that is, self-consolidation settlement unusually cannot be completed during several decades. To investigate the sedimentation properties of bauxite tailings, bauxite tailings slurry, phyllite residual soil, and kaolinite, we conduct sedimentation tests on these materials in varying pH and salt solution environments. The influence mechanism of the surface electrical properties of clay particles on the settlement of tailings slurry is investigated using the zeta potential test. The findings reveal that increases in the cation concentration and valence state lead to compression of the electric double layer on the surface of three types of soil particles, resulting in a decline in the repulsive potential energy and an increase in the gravitational potential energy. This in turn contributes to a reduction in the settling stable void ratio. As the pH increases, the zeta potentials of the three soils gradually decrease from positive to negative. A change in the pH at the isoelectric point, PZCedge, triggers the transformation of the kaolinite mineral arrangement. When the pH is either greater than or less than the isoelectric point, an increase or decrease in the pH results in expansion of the electric double layer of the clay particles and an increase in the pore content. The results of this study suggest that bauxite tailings mud is more likely to settle in an acidic environment than in an alkaline environment, thus an acidic settling environment should be utilized for bauxite tailings produced in industrial production.

The role of microplastics in the process of Paraclostridium sp. DLY7-assisted phytoremediation of phenanthrene contaminated soil

Microplastics can absorb polycyclic aromatic hydrocarbons (PAHs), decrease the bioavailability of pollutants, alter the soil microbial community, and thus might affect the dissipation of soil pollutants. However, whether microplastics could alter the remediation efficiency of PGPR-assisted plants for PAHs-contaminated soil has not been studied. This study assessed the remediation potential of PGPR exhibiting phenanthrene (PHE) degradation ability in assisting maize for PHE-contaminated soil. Especially, the role of microplastics involved in this remediation process was also investigated. The results showed that strain Paraclostridium sp. DLY7 (DLY7) significantly increased the PHE removal efficiency (63.4%) from soil by maize and reduced the content of PHE in maize leaves and roots with no microplastics addition. However, the presence of microplastics significantly inhibited the PHE removal from soil and increased the PHE accumulation in maize issues, in comparison with PHE + DLY7 treatment. Microplastics also significantly reduced soil sucrase and alkaline phosphatase activities, and the content of soil nitrate nitrogen and ammonium nitrogen under non-inoculation with strain conditions. Inoculation with strain DLY7 also altered the rhizosphere soil microbial community, enriched some beneficial bacteria and increased activities of some crucial soil enzymes, thus facilitating PHE removal from soil. On the whole, compared with conventional soil contamination remediation studies, this study innovatively pointed out that microplastics significantly reduced the removal efficiency of soil PHE and increased the uptake of PHE by maize in the PGPR-assisted phytoremediation process. However, the effects of microplastics on microorganisms might be related to the particle size, concentration and type of microplastics in the environment, which would be studied in our future research. These findings proposed new perspectives for revealing the role of microplastics on the efficiency of microbe-assisted phytoremediation of PAHs-contaminated soil.

Variability in the relationship between light scattering and chlorophyll a concentration in oligotrophic tropical regions of the Western Pacific Ocean.

It is important to determine the relationship between the concentration of chlorophyll a (Chla) and the inherent optical properties (IOPs) of ocean water to develop optical models and algorithms that characterize the biogeochemical properties and estimate biological pumping and carbon flux in this environment. However, previous studies reported relatively large variations in the particulate backscattering coefficient (bbp(λ)) and Chla from more eutrophic high-latitude waters to clear oligotrophic waters, especially in oligotrophic oceanic areas where these two variables have little covariation. In this study, we examined the variability of bbp(λ) and Chla in the euphotic layer in oligotrophic areas of the tropical Western Pacific Ocean and determined the sources of these variations by reassessment of in-situ measurements and the biogeochemical-argo (BGC-Argo) database. Our findings identified covariation of bbp(λ) and Chla in the water column below the deep Chla maximum (DCM) layer, and indicated that there was no significant correlation relationship between bbp(λ) and Chla in the upper layer of the DCM. Particles smaller than 3.2 µm that were in the water column above the DCM layer had a large effect on the bbp(λ) in the vertical profile, but particles larger than 3.2 µm and smaller than 10 µm had the largest effect on the bbp(λ) in the water column below the DCM layer. The contribution of non-algal particles (NAPs) to backscattering is up to 50%, which occurs in the water depth of 50 m and not consistent with the distribution of Chla. Phytoplankton and NAPs were modeled as coated spheres and homogeneous spherical particles to simulate the bbp(λ) of the vertical profile by Aden-Kerker method and Mie theory, and the results also indicated that the backscattering caused by particles less than 20 µm were closer to the measured data when they were below and above the DCM layer, respectively. This relationship also reflects the bbp(λ) of particles in the upper water was significantly affected particle size, but bbp(λ) in the lower water was significantly affected by Chla concentration. This effect may have relationship with phytoplankton photoacclimation and the relationship of a phytoplankton biomass maximum with particle size distribution in the water column according to the previous relevant studies. These characteristics also had spatial and seasonal variations due to changes of Chla concentration at the surface and at different depths. There was mostly a linear relationship between Chla and bbp(700) during winter. During other seasons, the relationship between these two variables was better characterized by a power function (or a logarithmic function) in the lower layer of the DCM. The spatial and vertical relationships between the bbp(λ) and Chla and the corresponding variations in the types of particles described in this study provide parameters that can be used for accurate estimation of regional geochemical processes.

THE SIMULATION AND PARAMETRIZATION OF THE LATERAL DISTRIBUTION FUNCTION IN EAS AT ULTRA HIGH ENERGIES

To characterize the features of EASs, this study used the AIRES simulation tool (Version 19.04.0) to estimate the lateral distribution function (LDF) at very high energies of different types of cosmic ray particles. An array of zenith angles spanning from 1018 to 1020 eV was used for the proton and iron primary simulations. The EASs's LDF curves are fitted with new coefficients for various primary particles and zenith angles using a polynomial fit, and these coefficients are applicable to the energy range described before. The findings of the simulation were compared with actual data from the Yakutsk EAS array, which showed decent agreement for proton and iron at 1019 eV for angled showers at θ=10ˢ.

Detachment and flow behaviour of anode slimes in high nickel copper electrorefining

Most of the world’s copper is produced via copper electrorefining, where nickel is the most abundant impurity in the process. Previously it has been suggested that nickel affects the adhesion of anode slimes on the anode as well as the porosity of the slime layer that forms. This paper investigates the effects of nickel, oxygen, sulphuric acid and temperature on the detachment of anode slimes from the anode surface. The detachment of particles as a function of both anode and electrolyte composition was studied on laboratory scale using a camera connected to a Raspberry Pi, and particle detection and movement analysed using TrackPy. The results revealed four different slime detachment mechanisms: cloud formation, individual particle detachment, cluster detachment and avalanche. These were found to be dependent on the electrolyte (0, 10, 20, 30 g/dm3 Ni2+ & 100, 200 g/dm3 H2SO4), with increasing nickel concentration promoting cluster detachment and increasing sulphuric acid concentration favouring detachment of individual particles. Anode composition (0.05-0.44 wt% O and 0.07-0.64 wt% Ni) was shown to affect the flow direction of anode slimes, with increasing nickel leading to more upward-flowing slimes. Typical particle movement velocities were from -0.5 to 1.0 mm/s regardless of the electrolyte and anode composition, and regardless of the operating temperature (25 °C & 60 °C) for small particles (<0.5 mm). The results also support previous findings that increasing the nickel concentration of the electrolyte leads to a more porous anode slime layer on the anode.

Comparative evaluation for the performance of environmental DNA and RNA analyses targeting mitochondrial and nuclear genes from ayu (Plecoglossus altivelis).

Environmental DNA and RNA (eDNA and eRNA; collectively eNA) analyses have the potential for non-invasive and cost-efficient biomonitoring compared with traditional capture-based surveys. Although various types of eNA particles, including not only mitochondrial eDNA but also nuclear eDNA and their transcripts, are present in the water, performances of eNA detection and quantification have not yet been evaluated sufficiently across multiple mitochondrial and nuclear genes. We conducted a tank experiment with ayu (Plecoglossus altivelis) to compare the detection sensitivity, yields per water sample, and quantification variability between replicates of each type of eNAs. The assay targeting the multi-copy nuclear gene exhibited a higher sensitivity than the assay targeting the mitochondrial gene, and both the target eDNA and eRNA concentrations per water sample were higher for the nuclear gene. On the contrary, variation in eRNA quantifications per sample does not necessarily correspond to that in eDNA, and the intra-sample quantification variability (represented as the CVs between PCR replicates) tended to be larger for eRNA than eDNA. Our results suggested that, even if suitable to the sensitive detection of species occurrence, the use of eRNA particularly derived from multi-copy nuclear gene may not be necessarily appropriate for the reliable assessment of species abundance. The findings in this study would help optimize eNA analyses for making biomonitoring and stock assessment in aquatic environments more efficient and reliable.

DRUG DELIVERY SYSTEMS BASED ON GELLAN DERIVATIVES

This paper proposes a review of the literature that reports valuable and interesting results regarding the biomedical applications of gellan and its derivatives. The different types of formulations for which this microbial exopolysaccharide is suitable are listed, which depend on the condition to be treated and their administration method: tablets, films, gels synthesized in situ, hydrogels, different types of particles, especially micro- and nanoparticles , mice etc. Research on the biomedical uses of gellan and its derivatives is far from being exhausted, newer directions regarding the creation of nanocomposites (with clays, for example), of mixtures or semi- and interpenetrated networks with other polymers revealing the obtaining of new extremely valuable biomaterials not only as supports for the encapsulation, transport and release of drugs, but also in the field of tissue engineering.

Microscopic characteristics and sources of atmospheric dustfall in open-pit mining coal resource-based city in the arid desert area of Northwest China

Atmospheric dustfall is solid air pollutant, has a major impact on the environment and human health. The objective of this study was to investigate the microscopic characteristics and sources of atmospheric dustfall in open-pit mining coal resource-based city in the arid desert area of Northwest China. The characteristics of size and shape factors, variation of shape factors with size distribution, types of individual particles, and sources of atmospheric dustfall, which were collected in the open-pit mining area and surrounding areas, were analyzed by X-ray diffraction (XRD) and scanning electron microscopy coupled with an energy dispersive spectrometer (SEM–EDS) combined with graphical method and shape factors. The results showed that the atmospheric dustfall in all functional areas was dominated by coarse-grained particles. The shape of the atmospheric dustfall deviated from spherical shape, and with decreasing particle size, the difference in shape factors increased in each functional area. The EDS and XRD analyses indicated the presence of 13 types of particles. The sources were mainly local and included soil dust from each functional area; industrial dust, construction dust, biogenic impurities, fossil fuel combustion, wear products of motor vehicle parts, motor vehicle exhaust emissions, and emission and excreta from biological activities in each functional area except the desert area; emissions from a steel plant in the industrial area; coal-associated ore, coal dust, coal gangue emissions, and emissions from the spontaneous combustion of coal gangue in the open-pit mining area; secondary chemical crystallization products in the industrial area and the open-pit mining area; dust generated by vehicles abrading the surface of the off-mine coal road and in the open-pit mining area.

Particle distributions in Lamb wave based acoustofluidics

Acoustic streaming enabled by a Lamb wave resonator (LWR) is efficient for particle trapping and enrichment in microfluidic channels. However, because Lamb waves combine the features of bulk acoustic waves and surface acoustic waves, the resulting acoustic streaming in the LWR occurs in multiple planes, and the particle flow behavior in this acoustofluidic system is largely unknown. Reported here are numerical simulations and laboratory experiments conducted to investigate the boundary conditions for particle motion inside a microvortex induced by an LWR. Upon dynamic capture, the particles’ trajectories become orbital paths within an acoustic vortex. The suspended particles encounter two distinct acoustic phenomena, i.e., the drag force resulting from acoustic streaming and the acoustic radiation force, which exert forces in various directions on the particles. When the acoustic radiation force and the fluid drag force are dominant for large and small particles in a mixed solution, respectively, the large particles reside within the vortex while the small particles remain at its periphery. Conversely, when the acoustic radiation force is dominant for both types of particles, the distribution pattern is reversed.

Round Robin Test of Absorptance and Emittance of Particles for CSP

Precise knowledge of particle optical properties is crucial to the advancement and success of directly-irradiated particle receiver technologies. This work presents the results of a Round Robin Test (RRT) that was conducted between seven laboratories, where each participant measured the absorptance and emittance for a set of five different particle types. This research was performed within the framework of the SolarPACES Task III group, and the results helped establish a guideline for evaluating the optical properties of particles. The guideline was published on the SolarPACES Task III website in May 2022.

Do you say uh or uhm? A cross-linguistic approach to filler particle use in heritage and majority speakers across three languages.

Filler particles like uhm in English or ähm in German show subtle language-specific differences and their variation in form is related to socio-linguistic variables like gender. The use of fillers in a second language has been shown to differ from monolinguals' filler particle use in both frequency and form in different language contexts. This study investigates the language-specific use of filler particles by bilingual heritage speakers in both their languages, looking at the dominant majority language in the society and their minority heritage language spoken at home. This is done based on heritage Russian and German data and majority German and English data from the RUEG corpus. Language-specific fillers were extracted from the corpus and analyzed for their occurrence and segmental form. The frequency analysis suggests an influence of bilingualism, age group, and formality of the situation on the filler frequency across all languages. The number of filler particles is higher in formal, older, and bilingual speech. The form analysis reveals an effect of language and gender on the type of filler particle. The vocalic-nasal filler particles (e.g., uhm) are more frequently found in German and English and in female speech of these languages. Heritage speakers of Russian in contact with German and English show higher use of vocalic-nasal forms also in their Russian while producing similar gender related patterns to monolingual speakers in both their languages. The higher frequency of filler particles in formal situations, older speakers and in bilingual speech, is discussed related to cognitive load which is assumed to be higher in these contexts while speech style which differs between situations and social groups is also considered as explanation. The higher use of vocalic-nasal filler particles in German and English suggests language specific filler particle preferences also related to the socio-linguistic variable gender in these languages. The results from heritage speakers suggest and influence on filler particle form in their heritage language, while also revealing socio-linguistic usage patterns related to gender which are produced by heritage speakers similarly to monolinguals in their respective language.