Stability Of Implants Research Articles

Comparison of osteogenic capability of 3D-printed bioceramic scaffolds and granules with different porosities for clinical translation.

Pore parameters, structural stability, and filler morphology of artificial implants are key factors influencing the process of bone tissue repair. However, the extent to which each of these factors contributes to bone formation in the preparation of porous bioceramics is currently unclear, with the two often being coupled. Herein, we prepared magnesium-doped wollastonite (Mg-CSi) scaffolds with 57% and 70% porosity (57-S and 70-S) via a 3D printing technique. Meanwhile, the bioceramic granules (57-G and 70-G) with curved pore topography (IWP) were prepared by physically disrupting the 57-S and 70-S scaffolds, respectively, and compared for in vivo osteogenesis at 4, 10, and 16weeks. The pore parameters and the mechanical and biodegradable properties of different porous bioceramics were characterized systematically. The four groups of porous scaffolds and granules were then implanted into a rabbit femoral defect model to evaluate the osteogenic behavior in vivo. 2D/3D reconstruction and histological analysis showed that significant bone tissue production was visible in the central zone of porous granule groups at the early stage but bone tissue ingrowth was slower in the porous scaffold groups. The bone tissue regeneration and reconstruction capacity were stronger after 10weeks, and the porous architecture of the 57-S scaffold was maintained stably at 16weeks. These experimental results demonstrated that the structure-collapsed porous bioceramic is favorable for early-stage osteoconduction and that the 3D topological scaffolds may provide more structural stability for bone tissue growth for a long-term stage. These findings provide new ideas for the selection of different types of porous bioceramics for clinical bone repair.

Effect of Implant Macro-Design and Magnetodynamic Surgical Preparation on Primary Implant Stability: An In Vitro Investigation.

Macro-geometry and surgical implant site preparation are two of the main factors influencing implant stability and potentially determining loading protocol. The purpose of this study was to assess the initial stability of various implant macro-designs using both magnetodynamic and traditional osteotomy techniques in low-density bone. The parameters examined included peak insertion torque (PIT), implant stability quotient (ISQ), and peak removal torque (PRT). Four groups of 34 implants each were identified in accordance with the surgery and implant shape: T5 group (Five implant and osteotomy using drills); M5 group (Five implant and magnetodynamic osteotomy using Magnetic Mallet); TT group (TiSmart implant and osteotomy with drills); and MT group (TiSmart implant and magnetodynamic osteotomy). Every implant was placed into a low-density bone animal model and scanned using CBCT. The PIT and PRT were digitally measured in Newton-centimeters (Ncm) using a torque gauge device. The ISQ was analyzed by conducting resonance frequency analysis. The PIT values were 25.04 ± 4.4 Ncm for T5, 30.62 ± 3.81 Ncm for M5, 30 ± 3.74 Ncm for TT, and 32.05 ± 3.55 Ncm for MT. The average ISQ values were 68.11 ± 3.86 for T5, 71.41 ± 3.69 for M5, 70.88 ± 3.08 for TT, and 73 ± 3.5 for MT. The PRT values were 16.47 ± 4.56 Ncm for T5, 26.02 ± 4.03 Ncm for M5, 23.91 ± 3.28 Ncm for TT, and 26.93 ± 3.96 Ncm for MT. Based on our data analysis using a t-test with α = 0.05, significant differences in PIT were observed between TT and T5 (p < 0.0001), M5 and T5 (p < 0.0001), and MT and TT (p = 0.02). Significant differences in the ISQ were found between TT and T5 (p = 0.001), M5 and T5 (p < 0.001), and MT and TT (p = 0.01). The PRT also exhibited significant differences between TT and T5, M5 and T5, and MT and TT (p < 0.0001). Our data showed favorable primary implant stability (PS) values for both implant macro-geometries. Furthermore, the magnetodynamic preparation technique appears to be more effective in achieving higher PS values in low-density bone.

Selecting biomaterials in the reconstructive therapy of peri-implantitis.

Peri-implantitis is a pathogenic inflammatory condition characterized by progressive bone loss and clinical inflammation that may compromise the stability of dental implants. Therapeutic modalities have been advocated to arrest the disorder and to establish peri-implant health. Reconstructive therapy is indicated for bone defects exhibiting contained/angular components. This therapeutic modality is based upon the application of the biological and technical principles of periodontal regeneration. Nonetheless, the comparative efficacy of reconstructive therapy and nonreconstructive modalities remains unclear. Therefore, the aim of this narrative review is to address major clinical concerns regarding the efficacy, effectiveness, and feasibility of using biomaterials in peri-implantitis therapy. In particular, the use of bone grafting materials, barrier membranes, and biologics is comprehensively explored.

Reliability of the multipeg™ transducer in measuring dental implant stability by using a resonance frequency analysis device (Osstell®): An observational clinical study

Background: Measuring implant stability is an important issue in predicting treatment success. Dental implant stability is usually measured through resonance frequency analysis (RFA). Osstell® RFA devices can be used with transducers (Smartpeg™) that correspond to the implants used as well as with transducers designed for application with Penguin® RFA devices (Multipeg™). Aims: This study aims to assess the reliability of a MultiPeg™ transducer with an Osstell® device in measuring dental implant stability. Materials and Methods: Sixteen healthy participants who required dental implant treatment were enrolled in this study. Implant stability was measured by using an Osstell® device with two transducers, namely, Smartpeg™ and Multipeg™. Insertion torque was also measured and recorded as &gt;50 and ≤50 N·cm. Unpaired t-test and Mann–Whitney U test were conducted to assess the relationships of the implant stability values obtained by the two transducers with insertion torque, whereas Pearson and Spearman's correlations were utilized to investigate correlations between the two transducers. Interclass correlation coefficients were applied to assess the reliability between the two transducers. Results: Implant stability measurements (primary and secondary) showed strong positive correlations between Smartpeg™ and Multipeg™. The reliability values between both transducers in primary and secondary implant stability measurements were 0.922 and 0.981, respectively. The use of both transducers revealed higher implant stability measurements for implants inserted with insertion torque &gt; 50 N·cm than those inserted with insertion torque ≤ 50 N·cm. Conclusions: This study demonstrated that the Multipeg™ transducer is reliable in measuring the stability of dental implants using an Osstell® device.

Influence of Implant Macro-Design, -Length, and -Diameter on Primary Implant Stability Depending on Different Bone Qualities Using Standard Drilling Protocols-An In Vitro Analysis.

(1) Background: Primary implant stability is vital for successful implant therapy. This study explores the influence of implant shape, length, and diameter on primary stability in different bone qualities. (2) Methods: Three implant systems (two parallel-walled and one tapered) with various lengths and diameters were inserted into polyurethane foam blocks of different densities (35, 25, 15, and 10 PCF) using standard drilling protocols. Primary stability was assessed through insertion torque (IT) and resonance frequency analysis (RFA). Optimal ranges were defined for IT (25 to 50 Ncm) and RFA (ISQ 60 to 80). A comparison of implant groups was conducted to determine adherence to the optimal ranges. (3) Results: Implant macro-design, -length, and -diameter and bone block density significantly influenced IT and RFA. Optimal IT was observed in 8/40 and 9/40 groups for the parallel-walled implants, while the tapered implant achieved optimal IT in 13/40 groups (within a 25-50 Ncm range). Implant diameter strongly impacted primary stability, with sufficient stability achieved in only one-third of cases despite the tapered implant's superiority. (4) Conclusions: The findings highlight the need to adapt the drilling protocol based on diverse bone qualities in clinical practice. Further investigations should explore the impact of these adapted protocols on implant outcomes.

Insertion Torque (IT) and Implant Stability Quotient (ISQ) Assessment in Dental Implants with and without Healing Chambers: A Polyurethane In Vitro Study

Primary Stability (PS) depends on different factors, such as bone structure (quality and density), implant characteristics (macro and micro), and the relationship between thread shape and implant insertion hole size. PS is crucial for the prognosis and success of dental implants. The use of healing chambers, which create empty spaces between the implant and peri-implant bone, helps reduce the risk of compressive bone necrosis. High Insertion Torque (IT) values could potentially lead to the deterioration of the implant-abutment connection. However, the optimal implant macro-structure and IT values remain unknown. In this study, implants with healing chambers (Test) and without (Control) were inserted into polyurethane blocks with densities of 10, 20, 30, and 40 pounds per cubic foot (PCF). In blocks with densities of 30 and 40 PCF, Control implants had significantly higher IT values than Test implants. Additionally, Control implants exhibited significantly higher Removal Torque (RT) values than Test implants, but only in the 30 PCF density block (p &lt; 0.0001). However, no differences were found between the implants in the 10, 20, and 40 PCF density blocks. Similarly, no significant differences were observed in the Implant Stability Quotient (ISQ) values between the Test and Control implants. The results of the present study confirm that adding healing chambers to the macro-structure of dental implants can significantly reduce IT values without affecting ISQ values. This suggests the potential for avoiding compression and damage to peri-implant bone while maintaining consistent levels of PS.

Surgical outcomes of unwrapped acrylic orbital implants: A review of 192 patients

The purpose of this study is to report the results in a series of acrylic orbital implant placements without the use of wrapping material. We retrospectively reviewed the records of the patients who underwent enucleation with acrylic orbital implant insertion without scleral wrapping at the Department of Ophthalmology, Poznań University of Medical Sciences, Poland, between 2013 and 2020. There were 192 patients: 102 women and 90 men, mean age: 60 years (range: 13-90 years). In the majority of cases, the reason for enucleation was uveal melanoma (148 patients-77.1%), followed by secondary glaucoma in 22 patients (11.5%) and painful, phthisical eye in 16 (8.3%). The median follow-up was 23 months (range: 1-96 months). The stability of the implants was satisfactory in the majority of cases, and there were no cases of implant migration identified during the study period. We noted a total of 4 (2%) implant exposures. Other postoperative complaints included eyelid malposition-21 patients (11%), Tenon's capsule thinning (15 patients-7.8%) and post-enucleation eye socket syndrome (PEES)-7 patients (3.6%). The rate of postoperative complications was associated only with a history of previous ocular surgery (P=0.006). The stability and functional outcomes of unwrapped acrylic orbital implants in this group of patients were satisfactory during the follow-up period.

Stress-strain and fatigue life numerical evaluation of two different dental implants considering isotropic and anisotropic human jaw.

Dental prostheses are currently a valid solution for replacing potential missing tooth or edentulism clinical condition. Nevertheless, the oral cavity is a dynamic and complex system: occlusal loads, external agents, or other unpleasant events can impact on implants functionality and stability causing a future revision surgery. One of the failure origins is certainly the dynamic loading originated from daily oral activities like eating, chewing, and so on. The aim of this paper was to evaluate, by a numerical analysis based on Finite Elements Method (FEM), and to discuss in a comparative way, firstly, the stress-strain of two different adopted dental implants and, subsequently, their fatigue life according to common standard of calculations. For this investigation, the jawbone was modeled accounting for either isotropic or anisotropic behavior. It was composed of cortical and cancellous regions, considering it completely osseointegrated with the implants. The impact of implants' fixture design, loading conditions, and their effect on the mandible bone was finally investigated, on the basis of the achieved numerical results. Lastly, the life cycle of the investigated implants was estimated according to the well-established theories of Goodman, Soderberg, and Gerber by exploiting the outcomes obtained by the numerical simulations, providing interesting conclusions useful in the dental practice.

Efficacy of laser in re-osseointegration of dental implants-a systematic review.

Despite their high success rates, peri-implantitis can affect the stability and function of dental implants. Various treatment modalities have been investigated for the treatment of peri-implantitis to achieve re-osseointegration. An electronic literature search was performed supplemented by a manual search to identify studies published until January 2022. Articles that evaluated re-osseointegration in peri-implantitis sites in animal models following laser therapy or antimicrobial photodynamic therapy (aPDT) were included. Case reports, case series, systematic reviews, and letters to the editor were excluded. Risk of bias and GRADE assessment were followed to evaluate the quality of the evidence. Six studies out of 26 articles identified on electronic search were included in this review. The studies included animal studies conducted on canine models. Four out of six studies reported a higher degree of re-osseointegration following treatment of implants with laser therapy. The findings suggest that laser decontamination shows potential in enhancing re-osseointegration, particularly with the Er: YAG laser, which effectively decontaminated implant surfaces. However, conflicting outcomes and limitations in the evidence quality warrant caution in drawing definitive conclusions. Based on the limited available evidence, laser therapy may show a higher degree of re-osseointegration of implants than mechanical debridement.

Design and development of a patient-specific temporomandibular joint implant: Probing the influence of bone condition on biomechanical response.

Total temporomandibular joint (TMJ) replacement is widely recognized as an effective treatment for TMJ disorders. The long-term stability of TMJ implants depends on two important factors which are design concepts for fixation to anatomical locations in the mandible and bone conditions. Other factors include stress distribution, microstrain in the peri-implant, bone attributes like bone conditions leading to the clinical complications and failures. This study addresses these limitations by examining the influence of patient-specific design concepts and bone conditions on TMJ implant performance. Clinical evidences support the importance of implant design on healing ability. Previous studies have focused on achieving precise implant fit based on geometric considerations, however those published studies did not explore the impact of such. Against this perspective, the present study reports the extensive finite element analysis (FEA) results, while analyzing the impact of a newly designed patient-specific TMJ implant to address clinical complications associated with various bone conditions, particularly osteoporotic bone. In validating the FEA results, the performance of additively manufactured patient-specific TMJ implants was compared with designs resembling two commonly used clinically approved implant designs. By addressing the limitations of previous research and emphasizing the importance of bone conditions, the study provides valuable guidelines for the development of next-generation TMJ implants. These findings contribute to enhanced clinical outcomes and long-term success in the treatment of TMJ disorders.

Investigating the impact of breast positioning control on physical treatment parameters in multi-catheter breast brachytherapy

PurposeTo assess the effects of a workflow for reproducible patient and breast positioning on implant stability during high-dose-rate multi-catheter breast brachytherapy.MethodsThirty patients were treated with our new positioning control workflow. Implant stability was evaluated based on a comparison of planning-CTs to control-CTs acquired halfway through the treatment. To assess geometric stability, button–button distance variations as well as Euclidean dwell position deviations were evaluated. The latter were also quantified within various separated regions within the breast to investigate the location-dependency of implant alterations. Furthermore, dosimetric variations to target volume and organs at risk (ribs, skin) as well as isodose volume changes were analyzed. Results were compared to a previously treated cohort of 100 patients.ResultsWith the introduced workflow, the patient fraction affected by button–button distance variations > 5 mm and by dwell position deviations > 7 mm were reduced from 37% to 10% and from 30% to 6.6%, respectively. Implant stability improved the most in the lateral to medial breast regions. Only small stability enhancements were observed regarding target volume dosimetry, but the stability of organ at risk exposure became substantially higher. D0.2ccm skin dose variations > 12.4% and D0.1ccm rib dose variations > 6.7% were reduced from 11% to 0% and from 16% to 3.3% of all patients, respectively.ConclusionBreast positioning control improved geometric and dosimetric implant stability for individual patients, and thus enhanced physical plan validity in these cases.

The effect of leukocyte- and platelet-rich fibrin on the bone loss and primary stability of implants placed in posterior maxilla: a randomized clinical trial

PurposeIn this study, we investigated the effects of leukocyte- and platelet-rich fibrin (L-PRF) on implant stability and alterations in the marginal bone surrounding posterior maxillary implants.MethodsThis randomized clinical trial was conducted to compare the variable of L-PRF placement around maxillary implants. Resonance frequency analysis (RFA) was used to evaluate the implant stability immediately after surgery and at 1, 2, 4, 6, 8, and 12 weeks after surgery (t0 to t6, respectively). In addition, the amount of marginal bone changes around the implant at t6 was compared with the baseline using periapical radiography.ResultsThe RFA outcomes were statistically significant within each group (P < 0.001, Eta2 = 0.322); however, in none of the follow-ups and immediately after the surgery, there was a significant difference between the two groups in terms of the implant stability quotient (ISQ) scores (P > 0.05). At t0, the test and control groups' respective mean levels of marginal bone loss around the implants were 0.4836 mm and 0.7343 mm, significantly different from the corresponding values at t6. On the other hand, marginal bone loss around the implant was not significantly different between the two groups in t0 and t6 (P = 0.532).ConclusionsL-PRF did not improve the RFA outcomes of implants three months after implant placement, and changes in the ISQ values over time were the same in both groups. In addition, L-PRF had no superior effect on the marginal bone loss around the implants.Trial registration number: The research was registered in the Iranian Registry of Clinical Trials on 22 December 2020 (No: IRCT20200624047906N1), available at http://www.irct.ir

Investigation on primary stability of dental implants through considering peri-implant bone damage, caused by small and large deformations: A validated non-linear micro finite element study

Primary stability of a dental implant is defined as its ability to resist the applied load without showing excessive damage in peri-implant bone, which is a prerequisite for secondary stability, and consequently for implantation success. The main goal of this study was to develop a validated micro-finite element (μFE) approach to assess the primary stability of dental implants in terms of stiffness, stiffness reduction, and irreversible displacement of the bone-implant system, subjected to an increasing step-wise quasi-static compressive loading-unloading test. The μFE models were generated based on the μCT images of bone, taken from extracted bovine tibia trabecular bone samples after drilling and implantation. A tissue constitutive model was considered for trabecular bone by describing elasto-plasticity with a modified von Mises yield criterion and element deletion technique to account for trabecular bone damage behavior. Then, the obtained force-displacement curves from the simulation were compared with the in-vitro mechanical test curves to evaluate the validity of the model. The results showed that the proposed μFE model could be properly predict the bone-implant system mechanical response in terms of irreversible displacement (R2 = 0.99), stiffness (R2 = 0.77), and stiffness reduction (R2 = 0.72) of the bone-implant construct for all the applied displacements without a significant difference from the unit slope and zero intercept of the QQ-plot (p-value<0.05). Moreover, a qualitative agreement was seen between the peri-implant bone damage predicted by the μFE model and the observed from μCT images. The adopted methodology used in this study can predict the mechanical failure response of the bone-implant system, which can be employed as a representative tool to study the effects of various dental implant design parameters on the primary stability with the ultimate goal of optimizing dental implants design.

Evaluation of Implant Stability According to Implant Placement Site and Duration in Elderly Patients: A Prospective Multi-Center Cohort Study.

The aim of this prospective study is to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants (diameter: 3.5/4.0/4.5/5.0 mm and length: 8.5/10.0/11.5 mm) in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n = 10), i.e., maxillary right-posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital six times: implant surgery, 1V; stitch removal, 2V; 1-month follow-up, 3V; 2-month follow-up, 4V; before final restoration delivery, 5V; and after final restoration delivery, 6V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α = 0.05). ISQ, PTV, and IST results of 4V and 5V were significantly higher than those of 1V (p < 0.05). The lowest ISQ results occurred in the E location at 4V and 5V (p < 0.05). In all mandibular locations, IST results of 6V were significantly higher than those of 1V, 2V, 3V, and 4V (p < 0.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors affecting the stability of the implant, it is necessary to determine the appropriate implant load application time. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability and the evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

A Comparison of Conical and Cylindrical Implants Inserted in an In Vitro Post-Extraction Model Using Low-Density Polyurethane Foam Blocks.

Combining tooth extraction and implant placement reduces the number of surgical procedures that a patient must undergo. Thus, the present study aimed to compare the stability of two types of conical implants (TAC and INTRALOCK) and another cylindrical one (CYROTH), inserted with a range of angulation of 15-20 degrees in low-density polyurethane blocks (10 and 20 pounds per cubic foot, PCF) with or without a cortical lamina (30 PCF), which potentially mimicked the post-extraction in vivo condition. For this purpose, a total of 120 polyurethane sites were prepared (10 for each implant and condition) and the Insertion Torque (IT), Removal Torque (RT), and Resonance Frequency Analysis (RFA) were measured, following a Three-Way analysis of variance followed by Tukey's post hoc test for the statistical analysis of data. The IT and RT values registered for all implant types were directly proportional to the polyurethane density. The highest IT was registered by INTRALOCK implants in the highest-density block (32.44 ± 3.28 Ncm). In contrast, the highest RFA, a well-known index of Implant Stability Quotient (ISQ), was shown by TAC implants in all clinical situations (up to 63 ISQ in the 20 PCF block without the cortical sheet), especially in lower-density blocks. Although more pre-clinical and clinical studies are required, these results show a better primary stability of TAC conical implants in all tested densities of this post-extraction model, with a higher ISQ, despite their IT.

Can Photobiomodulation Therapy Using an 810-nm Diode Laser Increase the Secondary Stability of Orthodontic Mini-Screws? A Split-Mouth Double-Blind Randomized Clinical Trial

Background: In orthodontic treatment, mini-screws can provide maximum anchorage conditions. If the miniscrew stability is compromised, this could jeopardize the outcomes of the orthodontic treatment or biomechanics. Photobiomodulation therapy (PBMt) is beneficial for biological tissues since it promotes wound healing with its anti-inflammatory and osteo-stimulatory properties. Objectives: The purpose of this study was to evaluate the effects of 810-nm Diode PBMt on the stability of orthodontic mini-screws for three months. Trial Design: Parallel, allocation ratio 1:1. Methods: Using a split-mouth technique, a total of 40 mini-screws were randomly allocated (1:1) to either a placebo laser application (P group) or a laser PBMt (L group). An 810-nm diode laser irradiation of 1 W output power, operating in continuous wave mode for 50 s, was applied in a sweeping movement at a 22 mm distance from the mini-screws. The allocated mini-screws first received PBMt at baseline, then every other day for five days, and then at each orthodontic visit (every three weeks) for a period of three months. At each visit, the stability of the mini-screws was measured by the Osstell Implant Stability Quotient (Osstell ISQ) at three points: lower, upper, and distal to the mini-screw. Results: The lower, upper, and distal ISQ values of irradiated and non-irradiated mini-screws significantly decreased at each point over time (p &lt; 0.001). No significant difference was found in the global ISQ values between the laser and the placebo group (p &gt; 0.05). Conclusion: PBM did not significantly increase the stability of orthodontic mini-screws over a period of three months. Trial Registration: Protocol was approved by the Research Ethics Committee of the Faculty of Dental Medicine of Saint Joseph University, Beirut, Lebanon University (#USJ/2019/161).

Effects of Implant Diameter on Implant Stability and Osseointegration in the Early Stage in a Dog Model.

Purpose: To determine the optimal implant diameter under limited bone width by comparing the effects of implants with different diameters on implant stability, peri-implant bone stability, and osseointegration. In addition, to evaluate the reliability of resonance frequency analysis (RFA) in detecting osseointegration and marginal bone level (MBL). Materials and Methods: Mandibular premolars and first molars of seven beagle dogs were extracted. After 8 weeks, their mandibular models and radiographic information were collected to fabricate implant templates. Implant sites were randomly divided into three groups according to diameter: Ø3.3, Ø4.1, and Ø4.8 mm. Implant stability quotient (ISQ) measurement and radiographic evaluation were performed after surgery (baseline) and at 4, 8, and 12 weeks. Three dogs were euthanized at 4 weeks to observe osteogenesis and implant-tissue interface biology. Four dogs were euthanized at 12 weeks to observe osseointegration. Hard tissue sections were prepared to analyze osteogenesis (fluorescence double labeling) and osseointegration (methylene blue-acid fuchsin staining). Results: At baseline and at 4, 8, and 12 weeks, the ISQ values of Ø4.1- and Ø4.8-mm implants did not differ (P > .05), but both had higher values than the Ø3.3-mm implants (P < .05). The mean marginal bone resorption (MBR) associated with Ø3.3-, Ø4.1-, and Ø4.8-mm implants was 0.65 ± 0.58 mm, 0.37 ± 0.28 mm, and 0.73 ± 0.37 mm, respectively. The buccal MBR of Ø4.8-mm implants was significantly higher than that of Ø4.1-mm implants (P < .05). The bone-to-implant contact (BIC) percentage at 12 weeks did not differ for any group (P > .05). The correlation coefficients between the ISQ and MBL of the Ø3.3-, Ø4.1-, and Ø4.8-mm implants were -0.84 (P < .01), -0.90 (P < .001), and -0.93 (P < .001), respectively, while that between the ISQ and BIC was 0.15 (P > .05). Conclusions: During the early healing stage, the performance of Ø4.1- and Ø4.8-mm implants in terms of implant stability was better than that of Ø3.3-mm implants. Implant diameter may not influence BIC percentage. RFA can be used to evaluate implant stability and MBL but is not suitable to assess the degree of osseointegration.

Primary and Secondary Stability of Short (4 mm) Versus Standard (≥ 10 mm) Implants Placed in the Same Mandible: A Prospective Clinical Study.

Purpose: To compare the stability of short vs standard (ie, regular-length) implants in the edentulous mandible. Materials and Methods: In this prospective clinical study, 20 patients with edentulous mandibles received four implants each-two short implants (4 mm) in the region of the first molar and two standard implants (≥ 10 mm) in the interforaminal region. Implant stability was assessed using resonance frequency analysis immediately after implant placement and at the day of the abutment connection after 3 months of healing in order to provide an implant stability quotient (ISQ). Results: Implant stability in the two implant groups at placement (ISQ: short 66.2; standard 68.2) and at abutment connection (ISQ: short 74.9; standard 75.7) did not differ substantially or statistically significantly (both P > .05). Findings did not change after statistically controlling for potential confounders such as bone quality and bone crest width. At abutment connection, 95% of the short and 97.5% of the standard implants demonstrated sufficient stability for conventional loading (P > .05). Conclusions: Short dental implants demonstrate similar primary and secondary stability compared to standard implants and seem to be a promising treatment option for rehabilitation of patients with edentulous mandibles.

Resonance Frequency Analysis to Assess the Stability of Immediate Implants: A Retrospective Clinical Trial.

Adequate implant primary stability is a key factor to obtain osseointegration and can be measured at insertion by insertion torque (IT) and at different timepoints with resonance frequency analysis (RFA), expressed as an implant stability quotient (ISQ). This retrospective study investigated the correlation between ISQ and IT at implant insertion. All patients who were eligible for this single-cohort retrospective clinical trial were treated with an immediate implant. IT parameters were recorded at implant insertion, and ISQ values were recorded at insertion and at 2-, 4-, and 12-month follow-ups. The study comprised 23 patients who received 32 implants. The mean IT value was 46.87 ± 9.66 Ncm (range: 25 to 65 Ncm), and the mean ISQ value at implant insertion was 71.45 ± 4.24 (range: 63 to 78); these values showed a statistically significant correlation (P < .0001). According to the present data and considering the implant design used in this trial, there is a statistically significant and positive correlation between IT and ISQ values. Thus, ISQ can be used as a reliable method to measure implant stability over time.

Correlation between Implant Stability and Alkaline Phosphatase in Controlled Diabetics: A Clinical Study

Correlation between Implant Stability and Alkaline Phosphatase in Controlled Diabetics: A Clinical Study