Urban Heat Research Articles

Unveiling the Urban Impact on Mesoscale Convective System Rainfall in the Pearl River Delta Urban Agglomeration Under Typical Synoptic Backgrounds

AbstractMesoscale convective systems (MCSs), the primary drivers of extreme rainfall over the Pearl River Delta (PRD) urban agglomeration, are strongly influenced by synoptic circulations and local geographical environments, including water bodies and topography. However, the urban impact on MCS rainfall under various synoptic backgrounds remain inadequately understood. Using a 20‐year high‐resolution MCS tracking database and self‐organizing map clustering, three typical backgrounds for MCSs, namely weak monsoon‐like, strong monsoon‐like, and low‐pressure system (Types‐1 to 3), impacting the PRD are identified. These backgrounds exhibit pronounced disparities in MCS tracks and temporal variations as well as rainfall distributions. Urban heat island (UHI) significantly alters the spatial patterns under Types‐1 and 2. Specifically, under weak UHI condition, MCS rainfall typically occurs offshore in the morning and shifts inland in the afternoon driven by the land‐sea breeze. However, UHI modifies the low‐level thermal structure, leading to anomalous convergence and instability, which causes morning rainfall to concentrate near coastal cities, while afternoon rainfall expands further inland to the northern rural region. Additionally, the strong southwesterly winds associated with Type‐2 enhance the interaction between topography and urban impact, resulting in even higher rainfall anomalies (+28.9%) over the northeastern region. The findings highlight the crucial role of urban impact and their synergistic effect with synoptic backgrounds and other land surface processes on MCSs.

Effects of urban areas on the diurnal cycle of temperature and precipitation in a global climate simulation

AbstractAnalyses of global climate model results for urban impacts on temperature and precipitation are rare. Previous analyses of the global Conformal Cubic Atmospheric Model simulation results for 1985–2010 have revealed urban effects on minimum and maximum temperatures. Using the same dataset to derive time‐zone‐corrected three‐hourly local time period (LTP) data, averaged diurnal cycles of temperature and precipitation were calculated for grid cells with greater than 10% urban fraction (urban grid cells) globally. Three latitudinal bands were assessed: northern extratropics (NET, 274 urban grid cells), southern extratropics (SET, 39 urban grid cells), and the Tropics (26 urban grid cells). The largest statistically significant urban influences on temperature are consistently found at night, in agreement with many previous studies on urban heat islands. Signs of urban cooling were found for a few hours, from 09:00 to 15:00 LTP, most often in summer. Influences of urban areas on precipitation varied, with small increases and decreases in all latitudinal bands and seasons. For NET, increases were generally found. In the Tropics, increases were found from 21:00 to 09:00 LTP for all seasons except DJF, with decreases for all seasons from 15:00 to 18:00 LTP. In SET, all seasons had increases for 21:00 to 00:00 LTP and decreases for 15:00 to 18:00 LTP. DJF had decreases for all LTPs except 21:00 to 00:00 LTP and SON had increases for all times except 15:00 to 18:00 LTP. Differences in rainfall in the region surrounding the urban areas were broadly similar to local changes in NET. For the Tropics and SET, regional decreases were found for DJF and JJA, with a more varied pattern for other months. Regional effects appeared to be more restricted to near‐urban areas in the Tropics than in NET. The results indicate some influence of nearby urban areas on regional temperature and precipitation.

Comparative analysis of airborne fungal spore distribution in urban and rural environments of Slovakia.

Monitoring airborne fungal spores is crucial for public health and plant production since they belong to important aeroallergens and phytopathogens. Due to different land use, their concentration can differ significantly between urban and rural areas. We monitored their spectrum and quantity on two geographically close sites with a different degree of urbanisation: Bratislava City and Kaplna Village in Slovakia, located 38km apart. We recorded the spectrum of airborne fungal spores over a year and confirmed the microscopic results by amplicon-based metagenomic analysis. The main spore season of the most frequent genera lasted over a week longer in Kaplna, but its intensity was approximately two-fold higher in Bratislava. This can be possibly connected to the microclimatic conditions of the urban area (especially wind speed and heat island effect) and the lesser use of fungicides. Cladosporium was the dominant genus on both sites, influencing the intensity most significantly. Through statistical analysis of the influence of meteorological parameters on airborne fungal spore levels, we identified a significant relationship with temperature, while the impact of other parameters varied depending on the spore type and release mechanism. Our results show the differences in airborne fungal spore levels between urban and rural areas and highlight the necessity for more monitoring stations in various environments.

Separating urban heat island circulation and convective cells through dynamic mode decomposition

AbstractThis study applies dynamic mode decomposition (DMD) to three‐dimensional simulation results of urban heat island circulation (UHIC, which is horizontal circulation) and thermals (vertical convections). The aim of this study is to revisit how these phenomena coexist based on the characteristics of temporal changes in the flow field. We used DMD to obtain the dominant spatial patterns and information on temporal changes. One of the modes of horizontal wind, which does not change temporally (no oscillation or amplification), exhibits a spatial UHIC pattern. The unique feature of this UHIC mode is that there are small‐scale striated structures (150–200 m) and large‐scale convergence. The other modes are time‐varying (oscillating and decaying) and represent smaller spatial‐scale phenomena (150–250 m), such as thermals. The frequency of each mode takes various values, some of which are lower than the lifetime of thermals in accordance with the Deardorff convective scale (~10 min). These low‐frequency modes showed striated structures similar to that observed in the UHIC modes. These results suggest that UHIC and thermals deform each other through components that vary in long temporal scales.

Urban Heat Island and Environmental Degradation Analysis Utilizing a Remote Sensing Technique in Rapidly Urbanizing South Asian Cities

Rapid urbanization in South Asian cities has triggered significant changes in land use and land cover (LULC), degrading natural biophysical components and intensifying urban heat islands (UHIs). This study investigated the impact of LULC changes on land surface temperature (LST) and the role of biophysical indicators in enhancing urban resilience to thermal extremes. We used Landsat satellite imageries from 1993 to 2023, conducted a comprehensive analysis of LULC changes, and estimated LST variations at 6-year intervals in the Dhaka, Gazipur, and Narayanganj districts in Bangladesh. Afterward, we performed statistical analysis upon employing correlation, regression, and principal component analysis (PCA) techniques to summarize information. The results reveal that 339.13 km2 worth of urban expansion has occurred in last 30 years, with an average annual growth rate of 3.5%, accompanied by a substantial reduction in water bodies (−139.17 km2) and vegetation cover. Consequently, summer temperatures exceeded approximately 36.52 °C in dense urban areas. Also, the results highlighted the strong influence of built-up areas (BSI and SAVI) on LST, while vegetation (NDVI) and water indices (NDWI) exhibited a negative association. The findings emphasize the urgency of integrating green infrastructure and deploying sustainable urban planning policies to mitigate the potential adverse impacts of scattered urbanization in the face of climate change.

A Methodological Framework for High-Resolution Surface Urban Heat Island Mapping: Integration of UAS Remote Sensing, GIS, and the Local Climate Zoning Concept

The urban heat island effect (UHI) is among the major challenges of urban climate, which is continuously intensifying its impact on urban life and functioning. Against the backdrop of increasingly prolonged heatwaves observed in recent years, practical questions about adaptation measures in cities are growing—questions that traditional meteorological monitoring can hardly answer adequately. On the other hand, UHI has long been the focus of research interest, but due to the technological complexity of providing accurate spatially referenced data at high spatial resolution and the requirement to survey at strictly defined parts of the day, information provision is becoming a major challenge. This is one of the main reasons why UHI research results are less often used directly in urban spatial planning. However, advances in geospatial technologies, including unmanned aerial systems (UASs), are providing more and more reliable tools that can be applied to achieve better and higher-quality information resources that adequately characterize the UHI phenomenon. This paper presents a developed and tested methodology for the rapid and efficient assessment and mapping of the effects of surface urban heat island (SUHI). It is entirely based on the integrated use of data from unmanned aerial systems (UAS)-based remote sensing methods, including thermal photogrammetry and GIS-based analysis methods. The study follows the understanding that correct SUHI research depends on a proper understanding of the urban geosystem, its spatial and structural heterogeneity, and its functional systems, which in turn can only be achieved by supporting the research process with accurate and reliable information resources. In this regard, the possibilities offered by the proposed methodological scheme for efficient geospatial registration of SUHI variations at the microscale, including the calculation of intra-urban SUHI intensity, are discussed in detail. The methodology builds on classical approaches for using local climate zoning (LCZ), adding capabilities for precise delineation of individual zone types and for geostatistical characterization of the urban surface heat island (SUHI). Finally, the proposed scheme is based on state-of-the-art technological tools that provide flexible and automated capabilities to investigate the phenomenon at microscales, including by enabling flexible observation of its dynamics in terms of heat wave manifestation and evolution. Results are presented from a series of sequential tests conducted on the largest residential area in Bulgaria’s capital city, Sofia, in terms of area and population, over a relatively long period from 2021 to 2024.

Urban burden of disease estimation for policy making

Abstract Introduction The Urban Burden of Disease Estimation for Policy Making (UBDPolicy) project aims to estimate the health impacts resulting from urban and transport planning related exposures in nearly 1000 European cities. So far, quantitative burden of disease assessments have estimated premature mortality attributable to the environmental stressors of air pollution, noise, urban heat islands and lack of green space for the year 2015. Regular reporting and trend monitoring of the health impacts associated with urban environments is crucial for assessing the wider impacts of urban and transport planning. Methods For almost 1000 European cities, quantitative Health Impact Assessments (HIAs) will be conducted that employ the comparative risk assessment methodology. Baseline exposure levels of air pollution, noise, urban heat islands and green space will be estimated and preventable health impacts modelled using counterfactual exposure scenarios. Analysis will comprise two components: firstly, the 2018 HIA will incorporate multiple environmental exposures for that year, while the second component will monitor trends at three-yearly reporting intervals covering the years of 2015, 2018, 2021 and 2024. Results Results are intended to shape evidence-informed urban planning and policies throughout Europe. By ranking cities according to environmental exposures and health impacts, cities are encouraged to address challenges and learn from successful urban design and planning policies in other cities. Discussion HIAs serve as an effective tool for identifying the health impacts of current and future urban policies. The provision of burden of disease estimates will provide policy-makers and practitioners robust data for informed decision-making, while estimates over time will allow tracking of changes from implemented policies. To fully harness the potential of cities as key drivers of sustainable and healthy living, robust evidence must be at the forefront of this change. Key messages • A multitude of urban and transport planning pathways contribute toward the health of urban populations. • Compact city designs often promote health, however there are exceptions.

Integrative Remote Sensing Approaches Using Generative Adversarial Networks for Urban Heat Island Analysis and Mitigation

Integrative Remote Sensing Approaches Using Generative Adversarial Networks for Urban Heat Island Analysis and Mitigation

Climate change health challenges – a study on heat health-related adaption measures in Germany

Abstract Problem Increasing extreme heat events of summer 2003, 2010 and 2015 induced a rising impact on heat health morbidity and mortality in Germany. A considerable proportion of urban population is affected by thermal discomfort due to the urban heat island burden during summer, particularly vulnerable people at risk. Concerted action to develop appropriate heat health adaptation measures is needed. Description As part of the National Adaptation Strategy to Climate Change an expert working group published ‘Recommendations for Action for the Preparation of Heat Action Plans’ for Germany in 2017. A first country-wide project had been conducted between 2019 and 2023 which investigated the status and impact of current or planned Heat Health Action Plans (HHAP), and adaptation measures appropriate to protect and prevent human health. As part of this project an online survey was conducted in May/June 2020 on the awareness and degree of use of the 2017 recommendations and the development and implementation of HHAP. Results This survey had been carried out to assess the current state of affairs as well as factors of success and barriers in the development and implementation of HHAP, with a particular focus on municipal environment and health administrations. In total 116 questionnaires had been responded, mainly by participants from the environment sector (53%), and 32% from the public health sector. More than half of the respondents indicated to be aware of the recommendations (very well-known at the federal state level: 90%, at county level known by 43%), which were identified as very helpful by 81%. Respondents from large cities (> 100 000 inhabitants) were main contributors to the study (41 of 81 large cities replied; 34 rural counties responded). Key messages • The 2017 recommendations had been identified and used to start with HHAP. • Decision makers should develop structures for regulations that anchor HHAP as a nationwide instrument to be established timely.

Ultrawhite and ultrablack asymmetric coatings for radiative cooling and solar heating

Passive daytime radiative cooling, a zero-energy and zero‑carbon cooling technology, has significant potential to substantially reduce reliance on compression-based cooling systems, combat the urban heat island effect, and mitigate global warming. However, current radiative cooling materials either exhibit low efficiency or are susceptible to overcooling, resulting in cooling penalties on winter days. In this work, we designed and fabricated the ultrawhite and ultrablack asymmetric coatings. The top-layer, designed for efficient radiative cooling, consists of a porous polymethyl methacrylate and hollow silica microspheres composite. The underlayer, tailored for solar heating, is composed of a carbon nanotubes and carbon black composite. The cooling side with an exceptional solar reflectivity of 0.98 and a mid-infrared emissivity of 0.97 achieves a comparable daytime subambient cooling of 7.6 °C, with a theoretical net cooling power of 98.8 W/m2. Conversely, the heating side with a solar absorptivity of 0.96, a ultra-high visible light absorptivity of 0.985, and a mid-infrared emissivity of 0.97, results in a daytime above-ambient heating of 12.8 °C, corresponding to a theoretical net heating power of 745 W/m2. Promisingly, our ultrawhite and ultrablack asymmetric coatings hold the promise of addressing the long-standing challenge of all-season temperature regulation, offering significant potential for electricity savings and CO2 emission reduction.

Implementation of WRF‐Urban Asymmetric Convective Model (UACM) for Simulating Urban Fog Over Delhi, India

AbstractAccurate fog prediction in densely urbanized cities poses a challenge due to the complex influence of urban morphology on meteorological conditions in the urban roughness sublayer. This study implemented a coupled WRF‐Urban Asymmetric Convective Model (WRF‐UACM) for Delhi, India, integrating explicit urban physics with Sentinel‐updated USGS land‐use and urban morphological parameters derived from the UT‐GLOBUS dataset. When evaluated against the baseline Asymmetric Convective Model (WRF‐BACM) using Winter Fog Experiment (WiFEX) data, WRF‐UACM significantly improved urban meteorological variables such as diurnal variations in 10‐m wind speed, 2‐m air temperature (T2), and 2‐m relative humidity (RH2) during a fog event. UACM also demonstrates improved accuracy in simulating temperature and significantly reducing biases for wind speed and daytime RH2 under clear sky conditions. UACM reproduced the nighttime urban heat island effect within the city, showing realistic diurnal heating and cooling patterns that are important for accurate fog onset and duration. UACM effectively predicts the onset, evolution, and dissipation of fog, aligning well with observed data and satellite imagery. Compared to WRF‐BACM, WRF‐UACM reduces the cold bias soon after sunset, thus improving the fog onset error by ∼3 hr. This study highlights the UACM's potential to improve fog prediction and its application in operational settings. With further investigation into different fog types, the UACM can provide crucial insights for preventive measures and reducing disruptions in urban areas.

Spatial Assessment of Urban Heat Island (UHI) in Kütahya using Landsat-8 Satellite Data

The Urban Heat Island (UHI) effect refers to the phenomenon where urban areas experience significantly higher temperatures than their rural surroundings due to human activities and modifications, such as replacing natural land cover with impervious surfaces, reducing vegetation, and increasing heat-absorbing materials. Kütahya central district has a dense population and building layout, which contributes to the intense UHI. Geographic Information System (GIS) and its tools are widely used in assessing UHI in urban areas, providing insights for both researchers and local authorities. Landsat-8 images acquired on August 8, 2023 (Path: 179, Row: 33, Cloud Cover: 0%) were utilized to create the Urban Heat Island (UHI) map for the study area. Through spatial analysis using Landsat-8 data for Kütahya city center, six different classes were defined, with the UHI map created using land surface temperature values. The highest and lowest UHI values vary between 4.245°C and -3.457°C. It has been observed that the average UHI increases by 12% in areas lacking dense building structures, characterized by rock surfaces and limited green areas. Conversely, in areas with parks, forests, and sparse settlements, the UHI decreases by 10%. With this study, a comprehensive evaluation of UHI was conducted for Kütahya city center. While the results obtained are expected to be an important resource for researchers and local authorities, they are also anticipated to be beneficial in the fields of engineering geology, urban geology, and urban planning.

Scale-Dependent Effects of Urban Canopy Cover, Canopy Volume, and Impervious Surfaces on Near-Surface Air Temperature in a Mid-Sized City

Cities are significantly warmer than their surrounding rural environments. Known as the ‘urban heat island effect’, it can affect the health of urban residents and lead to increased energy use, public health impacts, and damage to infrastructure. Although this effect is extensively researched, less is known about how landscape characteristics within cities affect local temperature variation. This study examined how tree canopy cover, canopy volume, and impervious surface cover affect daytime near-surface air temperature, and how these effects vary between different scales of analysis (10, 30, 60, 90 m radii), ranging from approximate street corridor to city block size. Temperature data were obtained from a car-mounted sensor, with traverse data points recorded during morning, afternoon, and evening times, plotted throughout the city of Portland, OR. The variability in near-surface air temperature was over 10° F during each traverse period. The results indicate that near-surface air temperature increased linearly with impervious surface cover and decreased linearly with tree canopy cover, with canopy volume reducing the temperature by 1° F for every 500 cubic feet of canopy volume for evening temperatures. The magnitude of the effect of tree canopy increased with spatial scale, with 60 and 90 m scales having the greatest measurable effect. Canopy volume had a positive relationship on presumed nighttime and early-morning temperatures at 60 and 90 m scales, potentially due to the impacts of wind fluctuation and air roughness. Canopy cover still contributed the largest overall decrease in street-scale temperatures. Increasing tree canopy cover and volume effectively explained the lower daytime and evening temperatures, while reducing impervious surface cover remains critical for reducing morning and presumed nighttime urban heat. The results may inform strategies for urban foresters and planners in managing urban land cover and tree planting patterns to build increased resiliency towards moderating urban temperature under warming climate conditions.

Evaluation and optimization of park cooling benefits based on cumulative impact and landscape pattern

City parks can cool the surrounding environment and mitigate the urban heat island (UHI) effect, considerable improving the city’s adaptability to climate. In this study, 20 city parks in Nanjing, China, were considered, and four indexes for quantifying the cooling benefits from a cumulative impact perspective were proposed. These indexes are park cooling area (PCA), park cooling efficiency (PCE), park cooling intensity (PCI), and park cooling gradient (PCG). The results reveal the following: first, city parks have a positive impact on the surrounding thermal environment. The factors park area (PA), park perimeter (PP), landscape shape index (LSI), and normalized difference vegetation index (NDVI) determine cooling benefits. Second, PA and PP are significantly positively correlated with PCA but are significantly negatively correlated with PCE. LSI is negatively correlated with PCE, while NDVI is positively correlated with PCI and PCG. No significant correlation exists between the four cooling indexes and modified normalized difference water index(MNDWI). Finally, different parks exhibit variations in their ability to provide cooling benefits. Special or community parks are more appropriately situated in areas with constrained urban land resources. In designing comprehensive parks, the intricate boundary features and vegetation conditions need to be considered to optimize their cooling effects. Moreover, a larger number of residents are allowed to enjoy cooling services. The findings of this project will aid in the construction and optimization of city parks in future to combat the UHI effect.

Nonlinear changes in urban heat island intensity, urban breeze intensity, and urban air pollutant concentration with roof albedo

This study systematically examines how the urban heat island (UHI) and urban breeze circulation (UBC) respond to an increase in roof albedo (αr) and its influence on urban air pollutant dispersion. For this, idealized ensemble simulations are performed using the Weather Research and Forecasting (WRF) model. The increase in αr from 0.20 to 0.65 decreases the UHI intensity, UBC intensity, and urban planetary boundary layer (PBL) height in the daytime (from 1200 to 1700 LST) by 47%, 36%, and 6%, respectively. As both UBC intensity and urban PBL height decrease, the daytime urban near-surface passive tracer concentration increases by 115%. The daytime UHI intensity, UBC intensity, and urban tracer concentration nonlinearly change with αr: For 0.10 ≤ αr < 0.80, the rates of changes in the UHI intensity, UBC intensity, and urban tracer concentration with αr overall increase as αr increases. For αr ≥ 0.80, the daytime roof surface temperature is notably lower than the daytime urban near-surface air temperature, the UHI intensity, UBC intensity, and urban tracer concentration very slightly changing with αr. This study provides insights into the associations between changes in roof surface temperature and roof surface energy fluxes with αr and those in UHI intensity.

Effects of Mixture Proportions and Molding Method on the Performance of Pervious Recycled Aggregate Concrete.

The use of pervious concrete pavement systems with recycled aggregates is a sustainable and innovative solution to major urbanization challenges such as repurposing construction waste, alleviating urban waterlogging, and reducing heat-island effects. This study aims to investigate the effects of mixture proportions and molding methods on the performance of pervious recycled aggregate concrete (PRAC). To this end, the coarse aggregate size (4.75~9.5 mm, 9.5~16 mm, and 16~19 mm), the molding method (layered insertion-tamping and vibration molding with vibration times of 5 s, 10 s, or 15 s, respectively), and the replacement rate of recycled coarse aggregate (RCA) (0%, 30%, 50%, and 100%, respectively) are considered. The results reveal that the addition of RCA to permeable concrete weakens its permeability. However, the compressive strength of PRAC reaches its maximum value when the RCA replacement rate is 50%. A larger aggregate particle size (16~19 mm) enhances the compressive strength of PRAC, yet decreases the permeability of PRAC. By using vibration molding to fabricate PRAC, an extension to the vibration duration increases the compressive strength, yet concurrently decreases the permeability. Based on the compressive strength and permeability coefficient of PRAC, the optimal mixture proportions and molding method are suggested.

Urban Heat Island Differentiation and Influencing Factors: A Local Climate Zone Perspective

With the acceleration of urbanization, the urban heat island (UHI) effect has become a major environmental challenge, severely affecting the quality of life of residents and the ecological environment. Quantitative analysis of the factors influencing urban heat island intensity (UHII) is crucial for precise urban planning. Although extensive research has investigated the causes of UHI effects and their spatial variability, most studies focus on macro-scale analyses, overlooking the spatial heterogeneity of thermal characteristics within local climate zones (LCZs) under rapid urbanization. To address this gap, this study took the central urban area of Chengdu, constructing a LCZ map using multisource remote sensing data. Moran’s Index was employed to analyze the spatial clustering effects of UHI across different LCZs. By constructing Ordinary Least Squares (OLS) and Geographically Weighted Regression (GWR) models, the study further explored the influencing factors within these climate zones. The results showed that: (1) Chengdu’s built and natural environments had comparable proportions, with the scattered building zone comprising the highest proportion at 22.12% in the built environment, and the low vegetation zone accounting for 21.8% in the natural environment. The UHII values in this study ranged from 10.2 °C to −1.58 °C, based on specific measurement conditions. Since UHII varied with meteorological conditions, time, seasons, and the selection of rural reference points, these values represented dynamic results during the study period and were not constant. (2) Chengdu’s urban spatial morphology and UHII exhibited significant spatial heterogeneity, with a global Moran’s I index of 0.734, indicating a high degree of spatial correlation. The highest local Moran’s I value was found in the proportion of impervious surfaces (0.776), while the lowest is in the floor area ratio (0.176). (3) The GWR model demonstrated greater explanatory power compared to the OLS model, with a fit of 0.827. The impact of spatial morphological factors on UHII varied significantly across different environments, with the most substantial difference observed in the sky view factor, which has a standard deviation of 13.639. The findings provide precise recommendations for ecological spatial planning, aiming to mitigate the UHI effect and enhance the quality of life for urban residents.

Assessment of indoor radon levels at multiple floors of an apartment building in the historic center of Rome (Italy): a comprehensive study

The urbanized area of Rome is largely built over volcanic deposits, characterized by a significant radionuclides content and consequently a high radon emanation potential. An accurate monitoring of workplaces and residential dwellings constitutes a first step towards mitigating the indoor radon exposure. Since radon diffusion dynamics involves complex interactions among many environmental parameters on different time scales, a proper assessment of radon concentration variations can be better achieved by means of active monitoring approaches. We present here the results of 1 year of continuous measurements conducted in six premises (five apartments and a basement) at different floors of the same building in the Esquilino district, in the historical center of Rome. Collecting annual series of radon concentration enables us to identify fluctuations over a seasonal scale, with radon generally decreasing in the warm season. The simultaneous tracking of different floors should cancel the influence of geogenic radon and of building characteristics like age, typology, and construction materials. While the basement shows the highest radon concentration, indicating a major contribution from the ground, we observe indoor radon levels comparable at all the upper floors, questioning the common belief that high-risk exposure be limited to the lowest storeys. The use of active devices makes it possible to discriminate between average indoor radon measured during the day and overnight, when residents are more likely to be at home. Our analysis provides the characterization of the dynamics of the gas emanation and transport inside the buildings and of its temporal fluctuations, in relation to the environmental and meteorological conditions. Since the experiment was performed in the Roman urban contest, we cannot ignore the specificity of the retrieved data, affected not only by endogenous factors like life habits relative to ventilation and conditioning of the apartments, but also by exogenous factors, among which the warmer microclimate compared to the surrounding suburban and rural areas, due to the effects of urbanization (urban heat island effect).

Assessing the impact of urban parks across Köppen climatic zones: a systematic review

This review article addresses the gap in the literature concerning the role of urban parks in providing cooling effects in hot and arid climatic zones. Using systematic review and content analysis of manuscripts from 1999 to 2023 in Scopus and Web of Science databases, elements and indicators of landscape architecture and their impacts on mitigating urban heat islands (UHI) have been explored. Our data mining revealed 190 manuscripts categorized into four Köppen climatic zones: tropical/mega thermal, arid, temperate/mesothermal, and continental/microthermal. Results indicate a scarcity of studies on hardscape elements’ impact, particularly in desert and semi-arid zones, and limited recognition of landscape architecture’s role in urban park cooling, especially in hot desert climates. Green areas emerged as the most cost-effective cooling strategy, with grass planted to minimize water elements and enhance tree cooling effects. However, the lack of softscape in hot, arid zones poses a significant challenge in mitigating UHI. These findings bridge the literature gap and suggest avenues for future research, including investigating native urban tree species and optimizing park area, shape, and orientation.

Efficient Rendering of Digital Twins Consisting of Both Static And Dynamic Data

Abstract. The high number of vertices and faces present in a digital twin of a large scene poses a challenge when executing large-scale simulations that require the data to be rendered multiple times with slight changes such as the light conditions in a day-night cycle during a long period of time (weeks and even months). Adding urban morphology such as tree planting introduces a new layer of complexity due to the requirement for evaluating different tree configurations and their effect on the local environment in the context of urban heat islands. Using advanced rendering techniques such as splitting a single buffer into sub-regions with inplace updates as well as buffer orphaning multiple methodologies are evaluated.