Fabry-Perot Research Articles

Low frequency vibration monitoring of wind turbine tower based on optical fiber sensor and its potential for internet of things

Among all renewable energy sources, wind energy is a cost-effective alternative energy source. The majority of wind turbines are built in harsh environments due to their power generation characteristics, which is one of the prime reasons resulting in frequent failures of wind turbine. Among various failures, the vibration of wind turbine tower cannot be ignored because it is a precursor of the failure of the wind turbine. The electrical vibration sensors have the problems of power supply and electromagnetic interference for the condition assessment of wind turbine tower. A vibration sensor based on optical Fabry-Perot (F-P) interference principle with high sensitivity is designed, fabricated and characterized to further meet the requirements of vibration detection of wind turbine tower. The mechanical simulation model of the diaphragm and optical vibration platform is constructed to verify the sensing characteristic of the F-P optical fiber vibration sensor (OFVS). The experiment results indicate a resonant frequency of the F-P OFVS of 223 Hz, an output sensitivity of 122.22 mV/m·s−2 at 10 Hz, and a horizontal output of less than 6 %. In addition, the designed F-P OFVS possesses the superiorities of compact structure, passive and excellent anti-electromagnetic interference, and has a wide application prospect in the vibration detection of the wind turbine tower.

DC current sensor based upon a fused fiber optic Fabry-Perot interferometer (FPI) and copper wire

In order to meet the demand for direct current (DC) current measurements in industrial production, a new type of fiber optic DC current sensor, combining thin copper wire and fiber optic Fabry-Perot interferometer (FPI), is reported. FPI is a sandwich structure formed by splicing a single-mode fiber (SMF) and a quartz capillary, with a cavity length of approximately 200 μm. The copper wire, with a length of 3.2 cm and a diameter of 1 mm, is attached to the FPI to form the sensor. Due to the excellent thermal conductivity of copper, the results showed that the sensor increased the sensitivity from 4.1 pm/°C to 11 pm/°C. After applying direct current to the sensor, a large quantity of heat generated by the copper wire was absorbed by the FPI, resulting in a significant shift in the resonant wavelength of FPI, which can indirectly measure the current. Three current experiments were performed, and parabolic curves have been used in fitting of the Dip wavelength and the square of the current. The results provide high correlation coefficients with values exceeding 0.99. Therefore, this curve may be used to measure the square of the current, further obtaining the current. In summary, the sensor is compact and durable, easy to manufacture, and provides high correlation coefficients, providing an alternative for measuring DC current.

Highly sensitive push-pull differential pressure sensor with multi-parameter measurement capabilities

A multi-parameter sensor comprising of a Fabry–Perot (FP) pair and a fiber-optic FP microcavity was proposed for simultaneous measurement of differential pressure (DP), static pressure (SP) and temperature. The push-pull FP pair is used to measure the differential pressure, and wide measurement range can be achieved by adjusting the dimensions of the diaphragm. The self-enclosed fiber-optic microcavity is utilized to measure the static pressure. For multi-parameter measurement, a matrix equation is proposed to solve the differential pressure, static pressure and temperature by fully considering the relationship of the FP cavity lengths and measurands. The performance of multi-parameter sensing is verified experimentally. The sensitivities of differential pressure, static pressure and temperature are 294.4822 nm/KPa, 353.08 nm/MPa and 42.4056 nm/°C, respectively, in variation of cavity lengths. The sensing characteristics show good linearity. Such a sensor could find important applications in the fields of process industry and oil industry, etc.

Flexible FPI sensor fabricated by fiber end photopolymerization and integration for high sensitivity gas pressure sensing

This work presents a new design framework for highly sensitive fiber gas pressure sensor. We construct a Flexible Fabry–Perot Interferometer (F-FPI), which consists of three polymer pillars and an end cap, on a fiber end face. A unique fiber-end photopolymerization and integration (FEPI) technique is adopted for fabricating the device. The varied gas pressure in the enclosed space not only changes the refractive index (RI) of the gas but also the length of the pillars. Therefore the difference in the optical path length of the FPI is more sensitive to pressure changes. Experimental results indicate that the F-FPI realizes a gas pressure sensitivity up to 79.0 pm/kPa in the range of 0–200 kPa. In addition, the Vernier effect is introduced to amplify the sensitivity to −409.7 pm/kPa. The temperature compensation is achieved by cascading a Fiber Bragg Grating (FBG) behind the F-FPI. Such a design framework provides a new idea for highly sensitivity gas pressure sensing.

Optical Fibers Use in On-Chip Fabry–Pérot Refractometry to Achieve High Q-Factor: Modeling and Experimental Assessment

This paper investigates the integration of optical fibers into an on-chip Fabry–Pérot (FP) resonator to achieve high-quality (Q) factors, which is favorable in sensing applications. Initially designed for high-speed data transmission, optical fibers are now utilized in sensing applications because of their flexibility and sensitivity to optical phenomena. This article focuses on the role of single-mode fibers (SMF) and the geometry of different structures in enhancing light confinement within FP resonators. Two distinct on-chip designs utilizing SMFs are demonstrated, modeled, and experimentally evaluated. One achieves a Q-factor higher than 5200, demonstrating significant improvement in light confinement, while the other maximizes the spectral range between the resonant modes’ peaks, maximizing the sensing range through the wavelength shift. This is supported by visualized simulation and coupling efficiencies calculations for fundamental and higher-order modes for comprehensive analysis. Comparison with existing literature is also made, underscoring the advancements achieved by the presented approaches. The findings contribute to the development of microscale refractive index sensing applications, highlighting the vital role of optical fiber integration for high-performance sensing.

SU-8-meta-phenylenediamine-conjugated thin film for temperature sensing.

Polymers have distinctive optical properties and facile fabrication methods that have been well-established. Therefore, they have immense potential for nanophotonic devices. Here, we demonstrate the temperature-sensing potential of SU8-meta-phenylenediamine (SU8-mPD), produced by epoxy amination of the SU-8 polymer. Its properties were examined through a series of molecular structural techniques and optical methods. Thin layers have demonstrated optical emission and absorption in the visible range around 420 and 520 nm, respectively, alongside a strong thermal responsivity, characterized by the 18 ppm °C-1 expansion coefficient. A photonic chip, comprising a thin 5-10 μm SU8-mPD layer, encased between parallel silver and/or gold thin film mirrors, has been fabricated. When pumped by an external light source, this assembly generates a pronounced fluorescent signal that is superimposed with the Fabry-Pérot (FP) resonant response. The chip undergoes mechanical deformation in response to temperature changes, thereby shifting the FP resonance and encoding temperature information into the fluorescence output spectrum. The time response of the device was estimated to be below 1 s for heating and a few seconds for cooling, opening a new avenue for optical sensing using SU8-based polymers. Thermoresponsive resonant structures, encompassing strong tunable fluorescent properties, can further enrich the functionalities of nanophotonic polymer-based platforms. This article is part of the theme issue 'Celebrating the 15th anniversary of the Royal Society Newton International Fellowship'.

Part-per-Billion (Ppb)-Level Acetylene Sensor Employing Optical Quartz Enhanced Photoacoustic Spectroscopy (QEPAS) with an Erbium-Doped Fiber Amplifier (EDFA) and a Fiber-Optic Fabry–Perot Interferometer

An all-optical double-pass quartz enhanced photoacoustic spectroscopy (QEPAS) sensor for the detection of acetylene (C2H2) at part-per-billion (ppb) levels was developed and experimentally validated. By employing an erbium-doped fiber amplifier (EDFA) capable of emitting up to 1 W of optical power, a commercial quartz tuning fork (QTF) resonating at 30.7 kHz, and double-pass acoustic microresonators, the amplitude of the QEPAS signal was significantly enhanced, thereby improving the sensitivity of the C2H2-QEPAS sensor. Instead of using piezoelectric detection in conventional QEPAS, a highly sensitive fiber-optic Fabry–Perot interferometer (FPI) was employed to measure the vibration of the QTF prong. A working point self-stabilizing technique was exploited to improve the demodulation sensitivity and stability. The linear response of the sensor to laser power and C2H2 concentration confirmed that no saturation occurred. With an excitation laser power of 1 W and a C2H2 absorption line of 1532.83 nm, a C2H2 minimum detection limit (MDL) of 19.1 ppb was achieved, corresponding to a normalized noise equivalent absorption coefficient (NNEA) of 1.58 × 10−8 cm−1∙W∙Hz−1/2. Owing to its high sensitivity, long-term stability, and immunity to electromagnetic interferences, the QEPAS sensor provides considerable potential for remote gas sensing in environmental monitoring and other applications.

Development of a high-sensitivity and fast-response fiber temperature sensor utilizing Ti3C2TX MXene/PDMS composites and Vernier effect.

Precisely measuring temperature holds great significance for human daily life and industrial production. A high-sensitivity and fast-response optical fiber temperature sensor based on the vernier effect is proposed. A Fabry-Perot interferometer (FPI) filled with Ti3C2TX MXene and polydimethylsiloxane (PDMS) composites is employed as a sensing probe for the first time, and a cascaded Mach-Zender interferometer (MZI) as a reference unit due to its insensitivity to temperature. The temperature sensitivity of the FPI filled with Ti3C2TX MXene/PDMS composites is 1.63 nm/°C owing to the excellent thermal expansion characteristics of PDMS, and the response time is shortened from 3.021 s to 719 ms compared to that of the FPI filled with pure PDMS attributed to the high thermal conductivity of MXene. The cascading of FPI and MZI with similar free spectral ranges generates the vernier effect. The sensitivity is magnified by 19.44 times, reaching up to 31.62 nm/°C in the range of 36.5 - 37.2 °C, and the response time is 721 ms. Furthermore, experimental results demonstrate the sensor's good stability, implying its potential applications of the sensor in medical diagnosis, environmental monitoring and biosensing.

Observational Evidence for the Neutral Wind Responses in the Mid‐Latitude Lower Thermosphere to the Strong Geomagnetic Activity

AbstractBased on two meteor radars in mid‐latitudes of China, the mid‐latitude lower thermospheric neutral wind responses to the 2015 St. Patrick's Day great storm are investigated. The AE and PCN indices presented the similar quasi‐5‐hour oscillations during the storm. Interestingly, the analogous and close‐correlated storm‐time quasi‐5‐hour oscillations were also observed in both the meridional wind differences at 90–102 km derived from meteor radars. The meridional wind disturbances in the lower thermosphere also showed the extension toward the lower latitudes. It has been found that the enhanced equatorward wind disturbances at 250 km estimated by the Horizontal Wind Model‐14 and Fabry‐Perot Interferometer (FPI) emerged accordingly with the increases of AE and PCN with a time delay. And the enhancements of equatorward (poleward) wind disturbances at 250 km were accompanied by the increments of equatorward (poleward) wind disturbances at 94 km with a time lag of a few hours. It is thus suggested that the multiple intensified Joule heating events with quasi‐5‐hour time intervals were triggered by the successive substorm expansions during the storm. Then the Joule heating events led to the vertical wind and temperature disturbances in the mid‐latitude lower thermosphere via disturbing the thermospheric meridional circulation, which consequently induced the quasi‐5‐hour meridional wind disturbances therein.

Multipeak ultraviolet lasing based on F-P mode from in-situ ZnO nanowire

Abstract High-quality ultraviolet singlemode and multimode lasing from zinc oxide nanowires are highly desirable. In this paper, we achieve high-Q lasing oscillation in vertically grown Zinc oxide (ZnO) microwires. The broad gain range reaches 13 lasing modes under high-energy excitation. We observe multiple peak emissions from the Fabry-Perot (F-P) lasing mode. In contrast, nanorod arrays with low aspect ratios exhibit amplified spontaneous emission (ASE) due to significant diffraction losses. Our work demonstrates that high-quality ZnO nanowires with an appropriate aspect ratio realize high-Q ultraviolet multipeak lasing based on F-P mode. These findings will benefit the design and fabrication of nanolasers based on nanowires.

A broadband acoustic metamaterial lens for sub-wavelength imaging based on bandwidth enhancement

Acoustic metamaterials manufactured from natural materials can exhibit exotic characteristics that cannot be found in nature materials through the design of geometric structures and resonance effects, and acoustic metamaterials can be used to achieve sub-wavelength acoustic imaging as the acoustic metamaterial lens (AML). Currently, the AMLs based on the Fabry–Pérot (FP) resonance principle are all with single effective length hole, which is directly related to the thickness of its structure. They can only achieve acoustic imaging in a relatively narrow frequency range, and there is no AML which can achieve broadband sub-wavelength acoustic imaging. In this paper, a kind of broadband acoustic metamaterial lens (BAML) is introduced. While maintaining a constant overall thickness of the AML, a design which is composed of the supercell consisting of a cross distribution of different effective length holes is proposed. This design enables the AML formed by these supercells to encompass multiple operating frequencies corresponding to various holes, thereby broadening the frequency range of acoustic imaging. Finite element simulation and imaging experiments were conducted, and results demonstrated that the BAML consisting of multiple effective length holes has the ability to enhance bandwidth of acoustic imaging. Compared to AML with single effective length hole, it offers a broader range of imaging frequencies, this design offers a general method of bandwidth enhancement. BAML has potential application value in ultrasonic imaging, sound absorption, intelligent thermal control and medical diagnosis.

High-resolution optical fiber underwater acoustic sensor enhanced by PDMS coating

This study introduces a high-resolution optical fiber underwater acoustic sensor utilizing a Fabry-Perot (FP) interferometer design. The sensor consists of a single-mode fiber (SMF) integrated with polydimethylsiloxane (PDMS), forming an FP cavity at the coated SMF terminus. The exceptional elasticity of PDMS amplifies vibrations from acoustic stimuli, modulating the FP cavity for effective acoustic wave detection. This integration of the probe within a single fiber, along with the PDMS coating technique, enhances the sensor’s SNR, resolution, and frequency response. The sensor’s simplicity, cost-effectiveness, superior signal-to-noise ratio, and low power consumption make it a promising tool for underwater acoustic applications.

Real-time in situ phase sensitivity calibration of interferometric fiber-optic ultrasonic sensors.

Output from a fiber-optic interferometric ultrasonic sensor can be affected by the operating point changes and/or the optical power fluctuations. We report a method for real-time and in situ calibration of the responses to ultrasound-induced phase delays for a low-finesse Fabry-Perot (FP) ultrasonic sensor demodulated using a phase-generated carrier. The carrier is produced from an electro-optic phase modulator, and its zero- and fundamental-carrier frequency components yield two quadrature signals. The same phase modulator is employed to generate controllable laser frequency modulations and calibration phase delay modulations. The response to the known calibration phase delays is used to gauge the sensor output in real time and in situ. The experiment has verified the effectiveness of the calibration method against the signal variations from both operating point changes and optical power variations.

Ultra-thin DLC diaphragm-based optical fiber sensor achieving a highly sensitive and broadband acoustic response.

In the design of an extrinsic Fabry-Perot interferometer (EFPI) acoustic sensor, broadband response and high-sensitivity sensing are usually conflicting and need to be carefully balanced. Here, we present a novel, to the best of our knowledge, optical fiber acoustic sensor based on an ultra-thin diamond-like carbon (DLC) film, fabricated using the plasma-enhanced chemical vapor deposition method, and transferred by a surface-energy-assisted method. The sensor exhibits a broadband response ranging from 200 Hz to 100 kHz, maintains an average sensitivity of 457.3 mV/Pa within the range of 6 to 30 kHz, and can detect weak acoustic signals down to 3.23 µPa/Hz1/2@16.19 kHz. The combination of an ultra-thin DLC film with a relatively high Young's modulus and internal stresses results in a trade-off between high sensitivity and a broadband response. This performance demonstrates that our sensor is among the most advanced in the EFPI acoustic sensor family, with significant potential for applications such as photoacoustic spectroscopy, defect diagnosis, and bio-imaging.

Design of near-infrared solid-state tunable Fabry-Perot filters based on VO2/P4VP films.

The significant refractive index change of VO2 during phase transition makes it attractive for the design of optical switches and filters, but high absorption of VO2 limits its development in the field of filter. In this paper, we firstly design near-infrared solid-state tunable/switchable single-/dual-band bandpass Fabry-Perot (F-P) filters based on VO2/P4VP composite films using COMSOL software. The simulation results show that the single-passband tunable filter can achieve a continuous thermal tuning range of 19 nm at 1064 nm, the full width at half maxima (FWHM) is 28.8 nm, and the peak transmittance is >30%. On this basis, we simulated a tunable dual-band bandpass filter, the left peak can be heated to achieve a tuning range of 15 nm (945 nm), the right peak is 24 nm (1168 nm), the peak transmittances of both the two peaks are >35%. When boosting the VO2 fraction, the continuous tunability of the above-mentioned single-/dual-band filters will be switchable due to the high absorption of VO2, and then switchable single-/dual-band bandpass filters are designed. This work has guiding significance for the design of novel filter structures and optical tunable devices based on phase change materials such as VO2 in the future.

Super-Spectral-Resolution Raman spectroscopy using angle-tuning of a Fabry-Pérot etalon with application to diamond characterization

Raman spectroscopy is an extremely powerful laser-based method for characterizing materials based on their unique inelastic scattering spectrum. Ultimately, the power of the technique is limited by the resolution of the spectrometer. Here we introduce a new method for achieving Super-Spectral-Resolution Raman Spectroscopy (SSR-RS), by angle-tuning a Fabry–Pérot (F-P) etalon filter that we incorporated in a micro-Raman setup. A monolithically coated F-P etalon structure, only 1.686 mm in thickness, was mounted onto an angle-tunable motorized stage, and Raman spectra were automatically acquired for many different angles of the etalon. Using a low-resolution grating of 150 g/mm by itself, without the F-P etalon, we obtained a best-case regular Raman spectral linewidth of 44 cm−1 for the characteristic Raman peak from a diamond sample. When we applied the SSR-RS technique to diamond, we obtained a super-spectral resolution peak that was 27x narrower, namely 1.63 cm−1, and a Raman shift of 1331.3 cm−1. To baseline SSR-RS, we applied the super-spectral-resolution method to extract the linewidth and peak wavelength of the laser excitation itself and obtained a laser linewidth of better than 0.014 cm−1, with a laser wavelength centered at 531.962 nm, close to the stated wavelength of 532 nm. This extracted laser linewidth is 3300x times narrower compared to its measured linewidth of 46 cm−1. Thus, our work suggests that SSR-RS can be very generally applied to greatly improve the resolution and precision of Raman instrumentation, and potentially lower the cost of obtaining high-resolution Raman spectroscopic capabilities.

Locking the wavelength of a narrow linewidth optical fiber laser to the peak transmitting wavelength of a Fabry–Perot filter

An optical fiber laser with a stable wavelength and a narrow linewidth spectrum is investigated by locking its wavelength to the peak transmitting wavelength of a Fabry–Perot filter. A fiber Bragg grating reflects the fluorescence emitted from erbium-doped fiber as the laser gain light; thus, the wavelength of the laser can be selected freely from the fluorescence spectrum of the erbium-doped fiber. The laser wavelength is locked to the peak transmitting wavelength of a Fabry–Perot filter, which compensates for the influences resulting from ambient disturbances with a feedback loop. The wavelength stability of the laser can exceed 10−8.

Spectrum contrast enhancement of fiber fabry-perot sensor by coupling efficiency improvement

This paper investigates the impact of interface angles on the coupling efficiency of a fiber Fabry-Perot interferometer (FFPI) sensor using both simulation and experimental methods. The FFPI sensor, which consists of a single-mode fiber (SMF), hollow-core fiber (HCF), and diaphragm, has its coupling efficiency determined by the generalized scattering matrix of the cascaded fiber system. To obtain the interface angles of the FFPI sensor, a new on-line monitoring system is developed based on microscopic images of the FFPI cavity and an image processing algorithm using OpenCV. By combining the eigenmode expansion method (EME) model and the online interface angle measurement technique, the coupling efficiency and spectral contrast of the FFPI cavity are evaluated and improved. Additionally, the corresponding working point in the intensity demodulation based FFPI sensor can be quickly identified. Using this method, an FFPI sensor with a spectral contrast of over 35 dB is achieved, which is significantly higher than existing similar sensors, and its sensitivity also reaches 50.80 mV/MPa. This work also holds significance for controlling and enhancing the spectral characteristics of other cascaded fiber optic sensors.

A Hermetic Package Technique for Multi-Functional Fiber Sensors through Pressure Boundary of Energy Systems Based on Glass Sealants

This paper presents a hermitic fiber sensor packaging technique that enables fiber sensors to be embedded in energy systems for performing multi-parameter measurements in high-temperature and strong radiation environments. A high-temperature, stable Intrinsic Fabry–Perot interferometer (IFPI) array, inscribed by a femtosecond laser direct writing scheme, is used to measure both temperature and pressure induced strain changes. To address the large disparity in thermo-expansion coefficients (TECs) between silica fibers and metal parts, glass sealants with TEC between silica optical fibers and metals were used to hermetically seal optical fiber sensors inside stainless steel metal tubes. The hermetically sealed package is validated for helium leakages between 1 MPa and 10 MPa using a helium leak detector. An IFPI sensor embedded in glass sealant was used to measure pressure. The paper demonstrates an effective technique to deploy fiber sensors to perform multi-parameter measurements in a wide range of energy systems that utilize high temperatures and strong radiation environments to achieve efficient energy production.

Cavity-length controllable Fabry–Perot interferometer based on Vernier effect

Cavity-length controllable Fabry–Perot interferometer based on Vernier effect