Channels Of Different Lengths Research Articles

Influence of pore structure heterogeneity on channeling channels during hot water flooding in heavy oil reservoir based on CT scanning

Hot water flooding is an effective way to develop heavy oil reservoirs. However, local channeling channels may form, possibly leading to a low thermal utilization efficiency and high water cut in the reservoir. The pore structure heterogeneity is an important factor in forming these channels. This study proposes a method that mixes quartz sand with different particle sizes to prepare weakly heterogeneous and strongly heterogeneous models through which hot water flooding experiments are conducted. During the experiments, computer tomography (CT) scanning identifies the pore structure and micro remaining oil saturation distribution to analyze the influence of the pore structure heterogeneity on the channeling channels. The oil saturation reduction and average pore size are divided into three levels to quantitatively describe the relationship between the channeling channel distribution and pore structure heterogeneity. The zone where oil saturation reduction exceeds 20% is defined as a channeling channel. The scanning area is divided into 180 equally sized zones based on the CT scanning images, and three-dimensional (3D) distributions of the channeling channels are developed. Four micro remaining oil distribution patterns are proposed, and the morphology characteristics of micro remaining oil inside and outside the channeling channels are analyzed. The results show that hot water flooding is more balanced in the weakly heterogeneous model, and the oil saturation decreases by more than 20% in most zones without narrow channeling channels forming. In the strongly heterogeneous model, hot water flooding is unbalanced, and three narrow channeling channels of different lengths form. In the weakly heterogeneous model, the oil saturation reduction is greater in zones with larger pores. The distribution range of the average pore size is larger in the strongly heterogeneous model. The network remaining oil inside the channeling channels is less than outside the channeling channels, and the hot water converts the network remaining oil into cluster, film, and droplet remaining oil.

Intrinsic Lipid Curvature and Bilayer Elasticity as Regulators of Channel Function: A Comparative Single-Molecule Study.

Perturbations in bilayer material properties (thickness, lipid intrinsic curvature and elastic moduli) modulate the free energy difference between different membrane protein conformations, thereby leading to changes in the conformational preferences of bilayer-spanning proteins. To further explore the relative importance of curvature and elasticity in determining the changes in bilayer properties that underlie the modulation of channel function, we investigated how the micelle-forming amphiphiles Triton X-100, reduced Triton X-100 and the HII lipid phase promoter capsaicin modulate the function of alamethicin and gramicidin channels. Whether the amphiphile-induced changes in intrinsic curvature were negative or positive, amphiphile addition increased gramicidin channel appearance rates and lifetimes and stabilized the higher conductance states in alamethicin channels. When the intrinsic curvature was modulated by altering phospholipid head group interactions, however, maneuvers that promote a negative-going curvature stabilized the higher conductance states in alamethicin channels but destabilized gramicidin channels. Using gramicidin channels of different lengths to probe for changes in bilayer elasticity, we found that amphiphile adsorption increases bilayer elasticity, whereas altering head group interactions does not. We draw the following conclusions: first, confirming previous studies, both alamethicin and gramicidin channels are modulated by changes in lipid bilayer material properties, the changes occurring in parallel yet differing dependent on the property that is being changed; second, isolated, negative-going changes in curvature stabilize the higher current levels in alamethicin channels and destabilize gramicidin channels; third, increases in bilayer elasticity stabilize the higher current levels in alamethicin channels and stabilize gramicidin channels; and fourth, the energetic consequences of changes in elasticity tend to dominate over changes in curvature.

High-Efficient and Broadband Acoustic Insulation in a Ventilated Channel With Acoustic Metamaterials

Acoustic insulation in ventilated structures is an important problem in acoustic engineering with many potential practical applications, such as the noise control for ventilating ducts of buildings, vehicles, or air conditioners. Acoustic metamaterial is a good candidate for the design of acoustic insulation for ventilated channel (AIVC) because the structural design with hard boundary has longer lifetime than conventional sound-absorbing cotton. In this paper, an AIVC with an open region and narrow channels of different lengths is proposed. We numerically and experimentally demonstrate its acoustic insulation larger than 20 dB (T < 0.01) within approximately 500–1,200 Hz with a subwavelength channel length of λ/6. The parameter dependence and air flow effect are numerically studied. Our findings show an alternative design of AIVC that may have applications in noise control and architectural acoustics.

Regulation of Gramicidin Channel Function Solely by Changes in Lipid Intrinsic Curvature.

Membrane protein function is regulated by the lipid bilayer composition. In many cases the changes in function correlate with changes in the lipid intrinsic curvature (c0), and c0 is considered a determinant of protein function. Yet, water-soluble amphiphiles that cause either negative or positive changes in curvature have similar effects on membrane protein function, showing that changes in lipid bilayer properties other than c0 are important—and may be dominant. To further investigate the mechanisms underlying the bilayer regulation of protein function, we examined how maneuvers that alter phospholipid head groups effective “size”—and thereby c0—alter gramicidin (gA) channel function. Using dioleoylphospholipids and planar bilayers, we varied the head groups’ physical volume and the electrostatic repulsion among head groups (and thus their effective size). When 1,2-dioleyol-sn-glycero-3-phosphocholine (DOPC), was replaced by 1,2-dioleyol-sn-glycero-3-phosphoethanolamine (DOPE) with a smaller head group (causing a more negative c0), the channel lifetime (τ) is decreased. When the pH of the solution bathing a 1,2-dioleyol-sn-glycero-3-phosphoserine (DOPS) bilayer is decreased from 7 to 3 (causing decreased head group repulsion and a more negative c0), τ is decreased. When some DOPS head groups are replaced by zwitterionic head groups, τ is similarly decreased. These effects do not depend on the sign of the change in surface charge. In DOPE:DOPC (3:1) bilayers, pH changes from 5→9 to 5→0 (both increasing head group electrostatic repulsion, thereby causing a less negative c0) both increase τ. Nor do the effects depend on the use of planar, hydrocarbon-containing bilayers, as similar changes were observed in hydrocarbon-free lipid vesicles. Altering the interactions among phospholipid head groups may alter also other bilayer properties such as thickness or elastic moduli. Such changes could be excluded using capacitance measurements and single channel measurements on gA channels of different lengths. We conclude that changes gA channel function caused by changes in head group effective size can be predicted from the expected changes in c0.

Optimization of the Ablative Laser Cutting of Shadow Mask for Organic FET Electrode Fabrication

This article presents an ablative method of cutting masks from ultra-thin metal foils using nanosecond laser pulses. As a source of laser radiation, a pulsed fiber laser with a wavelength of 1062 nm with the duration of pulses from 15 to 220 nanoseconds (ns), was used in the research. The masks were made of stainless-steel foil with thicknesses of 30 µm, 35 µm, and 120 µm. Channels of different lengths from 50 to 300 µm were tested. The possibilities and limitations of the presented method are described. The optimization of the cutting process parameters was performed using the experiment planning techniques. A static, determined complete two-level plan (SP/DC 24) was used. On the basis of the analysis of the test structures, we designed and produced precise shading masks used in the process of organic field effect transistor (OFET) electrode evaporation. The ablative method proved suitable to produce masks with canals of minimum lengths of 70 µm. It offers facile, fast, and economically viable shadow mask fabrication for organic electronics applications, which moreover might enable fast prototyping and circuit design.

Similarity of angular distribution for THz radiation emitted by laser filament plasma channels of different lengths.

The influence of plasma channel length on an angular terahertz (THz) radiation distribution is experimentally studied for the channel formed under filamentation of an ultrashort laser pulse. It is shown that the angular distribution of the THz emission depends only on laser intensity in the filament and plasma density of the plasma channel and does not depend on the plasma channel length. A qualitative explanation of the THz emission screening by the filament plasma channel is proposed.

On Features of Penetration of Vertical Free Turbulent Jets into Surface of Liquid in Narrow Channels of Different Lengths

The article presents new experimental results on the penetration of vertical plane and circular turbulent jets through a free surface of a liquid in relatively narrow channels of different extent with a overflow weir runoff mode. The behavior of the obtained experimental correlations for the period of arising self-oscillating flow modes is discussed. The analysis of a number of discovered features of the considered flows is carried out.

Using Fast Frequency Hopping Technique to Improve Reliability of Underwater Communication System

Acoustic underwater communication systems designed to work reliably in shallow coastal waters must overcome major limitations such as multipath propagation and the Doppler effect. These restrictions are the reason for the complexity of receivers being built, whose task is to decode a symbol on the basis of the received signal. Additional complications are caused by the low propagation speed of the acoustic wave in the water and the relatively narrow bandwidth. Despite the continuous development of communication systems using coherent modulations, they are still not as reliable as is desirable for reliable data transmission applications. This article presents an acoustic underwater communication system that uses one of the varieties of the spread spectrum technique i.e., the fast frequency hopping technique (FFH). This technique takes advantage of binary frequency-shift keying (BFSK) with an incoherent detection method to ensure the implementation of a system whose main priority is reliable data transmission and secondary priority is the transmission rate. The compromised choice of parameters consisted of the selection between the narrow band of the hydroacoustic transducer and the maximum number of carrier frequency hops, which results from the need to take into account the effects of the Doppler effect. In turn, the number of hops and the symbol duration were selected adequately for the occurrence of multipath propagations of an acoustic wave. In addition, this article describes experimental communication tests carried out using a laboratory model of the FFH-BFSK data transmission system in the shallow water environment of Lake Wdzydze/Poland. The test results obtained for three channels of different lengths are discussed.

Correlations of the capture efficiency with the Dean number and its constituents in heterogeneous microfluidic immunosensors

In heterogeneous microfluidic immunosensors, enhanced capture efficiencies of the antigens (Ag) in the carrier fluids by the surface-immobilized antibodies (Ab) facilitate lower detection limits and thus early detection of disease. Capture efficiency depends on the interplay of transport, reaction parameters and the geometry of the system. A detailed analysis on the enhanced capture efficiencies due to secondary flows in heterogeneous immunosensors has not received significant attention and is the theme of the present work. We conducted a systematic study to observe the significance of secondary forces on the capture efficiency, manifested as the average surface concentration (Cs,avg), in serpentine channels of different lengths (l) and radius of curvature (Rc) as a function of the Reynolds number (Re). Experimental observations were validated with numerical simulations. Micro-PIV studies at different planes and sections of the serpentine microchannels were conducted and matched with the simulated velocity profiles. Further investigation of the process and the geometrical parameters was conducted using numerical simulation and the behaviour of Cs,avg as a function of Re and Rc was plotted for different cases. A highlight of the present work are correlations of Cs,avg as a function of the Dean number (De), as well as its constituents (Re and α). The scientific studies of the geometrical and process parameters which affect the analyte capture advance the understanding of the phenomena and the proposed engineering correlations would be useful in the design of more efficient flow-based heterogeneous immunosensors.

Soft implantable device with drug-diffusion channels for the controlled release of diclofenac

We propose the use of an implantable device with multiple embedded drug diffusion channels, each of which is connected to a drug reservoir, for the controlled release of diclofenac. To minimize the size of the incision needed during device implantation, the device used herein was made of the soft biocompatible material polydimethylsiloxane (PDMS), thereby allowing for folding during device implantation. We aimed to achieve a profile of diclofenac release that was reproducible even after folding, and thus the channel was filled with cross-linked gelatin, which could be swollen via the infiltration of a bodily fluid to compensate for any possible defects formed during folding. We first assessed the use of individual channels of varying lengths of 1–12 mm, and the onset time and average rate varied from 1 to 14 days and from 0.31–4.3%/day, respectively. According to these results, we prepared a device with multiple integrated pairs of drug reservoirs and channels of different lengths (i.e., the SDD_I), in which the channel combination was selected to achieve the long-term, zero-order release of the largest amount of drug. Thus, the SDD_I used herein exhibited almost zero-order drug release for 55 days at a release rate of 1.19%/day (179.8 μg/day), which did not vary even after the device was folded multiple times due to the presence of gelatin in the channel. When tested in living rats, the SDD_I device could be folded and inserted subcutaneously through an incision less than half the size of that needed for the implantation of the unfolded, intact SDD_I. For both the unfolded and folded SDD_I devices, the drug concentration in blood was observed to be maintained within a similar range due to the almost zero-order, reproducible release of diclofenac.

Paper-based device with on-chip reagent storage for rapid extraction of DNA from biological samples

Conventional methods for extraction of DNA are expensive, time-consuming and tedious. To overcome these limitations, a paper-based DNA extraction device was developed that incorporates sponge-based buffer storage, a paper-based valve and channels of different length to autonomously direct the reagent and sample to the Fusion 5 disk for DNA capturing. With this device, DNA can be extracted within 2 min from only 30 μL samples of whole blood, serum, breast cancer cell, saliva, sputum and bacterial suspension. The device can also extract Hepatitis B Virus DNA from clinical blood samples and after quantification shows a detection limit as low as 104 copies⋅mL−1. This highlights its potential use in future diagnostics. The performance of the device was similar to that of the commercial QIAamp DNA micro kits and the FTA card. In our perception, this simple, inexpensive, portable and disposable device holds great promise in terms of POC testing in resource-poor settings.

Passive fluidic diode for simple fluids using nested nanochannel structures.

In this paper, we propose a moving part-free fluidic diode for simple fluids using nested nanochannels, which contain inner and outer channels of different lengths. Molecular dynamics simulations show that the fluidic diode accepts water flows in the forward direction and blocks flows in the backward direction in a wide range of pressure drops. The anisotropic flow rates are generated by the distinct activation pressures in different directions. In the forward direction, the activation pressure is low, which is determined by the infiltration pressure of the inner channel. In the backward direction, the activation pressure is quite high due to the capillary effects when flows are released from the inner to the outer channel. The pressure drop range for the fluidic diode can be varied by changing the channel size or surface wettability. The fluidic diode offers an alternative way for flow control in integrated micro- and nanofluidic devices.

Dynamics of the resistive state of a narrow superconducting channel in the ac voltage driven regime

Within the framework of the time-dependent Ginzburg–Landau equations, the dynamics of the order parameter in narrow superconducting channels of different lengths is investigated in the ac voltage-driven regime. The resistive state of the system at low frequencies of the applied voltage is characterized by the formation of time-periodic groups of oscillating phase-slip centers (PSCs). Increasing the frequency reduces the lifetime of these periodic groups. Depending on the length of the channel, the ac voltage either tends to restore the state with a single central PSC in periodic groups or minimizes the number of forming PSCs and induces their ordering in the system. For relatively short channels, a further increase in frequency leads to the suppression of the order parameter without PCS formation. For the systems with the channel length exceeding the specified limit, the formation of PSC starts after a certain time delay which increases rapidly with frequency. The current-voltage characteristics of a relatively short channel at different applied voltage frequencies are calculated. It is found that the current-voltage characteristics exhibit a stepped structure, where the height of the first step is determined by the quadruple value of the Josephson frequency.

Phase diagram of the resistive state of a narrow superconducting channel in the voltage-driven regime

Based on the numerical solution of the non-stationary (time-dependent) Ginzburg–Landau equations, we investigated the evolution of the order parameter of superconducting channels of different length under applied voltage (so-called voltage-driven regime). We calculated the current-voltage characteristics for channels of different lengths and found out the origin of their characteristic disorder oscillations. For very long channels in a certain voltage interval we revealed chaotic dynamics of the order parameter. The collected data allowed us to plot the most complete and detailed phase diagram of the resistive state of the superconducting channel in the voltage-driven regime.

Sound diffraction by a barrier with a fan-shaped headpiece

With respect to a noise barrier, sound diffraction by a half-plane with a fan-shaped headpiece is calculated. The fan consists of a set of rigid strips of different widths, which form narrow wedge-shaped channels of different lengths. The channels are connected to each other through the inner cylindrical cavity into which the inner open ends of the channels face. The curves representing the degree of sound suppression as a function of the frequency and the angle of incidence of sound waves are calculated. These curves demonstrate the high efficiency of the proposed barrier.

Interactions of drugs and amphiphiles with membranes: modulation of lipid bilayer elastic properties by changes in acyl chain unsaturation and protonation.

Poly-unsaturated fatty acids (PUFAs) alter the function of many membrane proteins, whereas monounsatured fatty acids generally are inert. We previously showed that docosahexaenoic acid (DHA) at pH 7 decreases the bilayer stiffness, consistent with an amphiphile-induced increase in elasticity, but not with a negative change in curvature; oleic acid (OA) was inert (Bruno, Koeppe and Andersen, Proc. Natl. Acad. Sci., 2007, 104, 9638-9643). To further explore how PUFAs and other amphiphiles may alter lipid bilayer properties, and thus membrane protein function, we examined how changes in acyl chain unsaturation and head group charge and size alter bilayer properties, as sensed by bilayer-spanning gramicidin A (gA) channels of different lengths. Compared to DHA, the neutral DHA-methyl ester has reduced effects on bilayer properties and 1-palmitoyl-2-docosahexaenoyl-phosphatidylcholine (PDPC) forms bilayers that are softer than dioleoylphosphatidylcholine (DOPC). The changes in channel function are larger for the short gA channels, indicating that changes in elasticity dominate over changes in curvature. We altered the fatty acid protonation by titration: docosahexaenoic acid (DHA) is more potent at pH 9 (relative to pH 7) and is inert at pH 4; OA, which was inert at pH 7, becomes a potent modifier of bilayer properties at pH 9. At both pH 7 and 9, DHA and OA produced larger changes in the lifetimes of the short gA channels, demonstrating that they increase lipid bilayer elasticity when deprotonated--though OA promotes the formation of inverted hexagonal phases at pH 7. The positively charged oleylamine (OAm), which has a small head-group and therefore should be a negative curvature promoter, inhibited gA channel function with similar reductions in the lifetimes of the short and long gA channels, indicating a curvature-dominated effect. Monitoring the single-channel conductance, we find that the negatively charged fatty acids increase the conductance by increasing the local negative charge around the channel, whereas the positively charged OAm has no effect. These results suggest that deprotonated fatty acids increase bilayer elasticity by reversibly adsorbing at the bilayer/solution interface.

A universal law to characterize ohmic contacts of small high electron mobility transistors

We have processed very small high electron mobility transistor (HEMT) on the two dimensional electron gas of a GaAs/GaInAs heterostructure. The contacts (down to 2 μm wide) connect channels of different lengths and widths. We measure the saturation I(V) curves and obtain the source drain voltage at saturation. Experiments demonstrate a universal linear dependence of the saturation voltage drop with the length of the channel, whatever its width. Our experimental result is understood with basic equations of the 2D channel, taking into account the contact resistivity. The universal law Usat(L) gives a nice way to measure easily and precisely the resistivity of contacts in ultrasmall devices when their width cannot be precisely known, like in narrow two dimensional electron gas.

Polymeric rolled-up microtubes by using strained semiconductor templates

In this paper it is reported a novel approach for the fabrication of polymeric microtubes based on the combination of semiconductor strain released thin films and Layer-by-Layer (LbL) deposition technique. The structure consisting of a LbL self-assembled polylectrolytes (PEs) film deposited onto a strained GaAs/InGaAs bilayer, was properly patterned and structured to enable the self rolling of an array of channels of different lengths. Then, the semiconductor film, acting as a sacrificial template, was selectively etched to obtain polymer microtubes. The so-realized polymeric channels were characterized in detail using Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Additionally, such microtubes were analyzed by confocal microscopy to prove the successful incorporation of a dye molecule within the polymeric nanowalls.

On the Limits of High-Speed Microthermal Focusing Field-Flow Fractionation

The migration of microparticles exposed to gravitational-buoyancy force and lift force and transported by the flow of the carrier liquid inside microfluidic conduits was studied from the viewpoint of the transient period (the relaxation) between the moment at which the particles start to be transported by the hydrodynamic flow and the time at which they are focused at an equilibrium position. Relaxation times were calculated theoretically by the incremental numerical method and the results were compared with the experimental data obtained on two microfluidic channels of different lengths and for different average linear velocities of the carrier liquid. It has been found that the maximal linear velocity of the carrier liquid in a microthermal field-flow fractionation channel whose dimensions were already optimized is of the order of a few cm/s under the investigated experimental conditions. At this velocity, the contribution of the secondary relaxation time is negligible compared to the retention time of the micrometer-sized particles.

Thiazolidinediones Alter Lipid Bilayer Properties and Native Voltage-Gated Sodium Channel Function

Thiazolidinediones (TZD) are selective peroxizome-proliferator receptor gamma (PPARγ) agonists that are used to treat hyperglycemia in type 2 diabetes. In addition to their hypoglycemic actions they have anti-inflammatory, anti-atherosclerotic and cardiovascular effects, but PPARγ activation does not account for all their actions. Three TZDs - troglitazone (Resulin), rosiglitazone (Avandia), and pioglitazone (Actos) - have been marketed; troglitazone was subsequently withdrawn due to hepatotoxicity and a precursor TZD - ciglitazone- was discontinued after phase II trials. TZDs, with troglitazone being the most potent, modulate L-type calcium and delayed-rectifier potassium channels by a seemingly PPARγ-independent mechanism. This could result from the adsorption of the amphiphilic TZDs to the membrane/solution interface, which can alter bilayer properties such as thickness, intrinsic curvature and the elastic moduli, and thus membrane protein function. We therefore examined whether TZDs alter lipid bilayer properties. We exploited the sensitivity of gramicidin channels to changes in bilayer properties to test for TZD-induced bilayer effects. TZDs alter gramicidin channel function and shift the monomer-dimer equilibrium toward the conducting dimers. Using gramicidin channels of different lengths we find that the TZD effects do not vary with changes in hydrophobic mismatch. Increasing bilayer stiffness with cholesterol amplifies the TZD-mediated changes in gramicidin channel function. Based on the concentrations at which we observe changes in gramicidin lifetime and appearance frequency, the potency is troglitazone>rosiglitazone>ciglitazone>pioglitazone, consistent with their effects on native membrane proteins. We examined the TZDs effects in native membranes using neuronal voltage-gated sodium channels (NaV) using whole-cell recordings. All TZDs caused a negative shift in the voltage-dependence of inactivation at concentrations similar to those that alter gramicidin channel function. Our results show that TZDs affect bulk membrane properties at concentrations that modulate native ion channels.