Broadband X-ray Source Research Articles

Quantifying motion blur by imaging shock front propagation with broadband and narrowband X-ray sources

Time-integrated radiography using MeV Bremsstrahlung X-ray sources is the norm for imaging during system-level testing of components and structures under dynamic condition. One source of error in the analysis of the time-integrated radiography data sets stems from motion blur which smears out sharp interfaces to a greater degree with longer exposure times, which become necessary to provide sufficient signal-to-noise with low X-ray penetration of objects of interest. To quantify motion blur, a 1D shock wave through PMMA was investigated experimentally at The Dynamic Compression Sector at The Advanced Photon Source (DCS@APS) with tapered broadband and 25.46 ± 1.06 keV narrowband X-rays. Four cameras with different exposure times were used for each experiment to compare the effect that exposure time has on motion blur. In addition, our methodology to accurately simulate motion blur in terms of transmission and shape is presented and compared to our experimental results and quantified. There is a high level of agreement between the experimental and simulation results across the range of data sets investigated in this study with a percent difference range of 0.29–1.31% for the four shots. The methodology of this work serves as a steppingstone towards a physically validated model that could be used in conjunction with experimental results to deconvolve physical parameters, densities, and interfaces of interest in a way that would not be possible with experimental results alone.

Broadband soft X-ray source from a clustered gas target dedicated to high-resolution XCT and X-ray absorption spectroscopy.

The development of the broad-bandwidth photon sources emitting in the soft X-ray range has attracted great attention for a long time due to the possible applications in high-resolution spectroscopy, nano-metrology, and material sciences. A high photon flux accompanied by a broad, smooth spectrum is favored for the applications such as near-edge X-ray absorption fine structure (NEXAFS), extended X-ray absorption fine structure (EXAFS), or XUV/X-ray coherence tomography (XCT). So far, either large-scale facilities or technologically challenging systems providing only limited photon flux in a single shot dominate the suitable sources. Here, we present a soft, broad-band (1.5 nm - 10.7 nm) soft X-ray source. The source is based on the interaction of very intense laser pulses with a target formed by a cluster mixture. A photon yield of 2.4 × 1014 photons/pulse into 4π (full space) was achieved with a medium containing Xe clusters of moderate-size mixed with a substantial amount of extremely large ones. It is shown that such a cluster mixture enhances the photon yield in the soft X-ray range by roughly one order of magnitude. The size of the resulting source is not beneficial (≤500 µm but this deficit is compensated by a specific spectral structure of its emission fulfilling the specific needs of the spectroscopic (broad spectrum and high signal dynamics) and metrological applications (broad and smoothed spectrum enabling a sub-nanometer resolution limit for XCT).

Calibration of image plate and back illuminated charge coupled device detectors at the thermal emission band of high Z target laser produced plasmas (80–800 eV)

We present a systematic method to absolutely calibrate detector efficiency vs photon energy using a laser produced plasma broadband x-ray source, a gold standard calibrated detector, and transmission gratings (TGs) as dispersive elements. Calibration uses one calibrated TG and a calibrated gold standard detector on one channel and a second calibrated TG and a detector to be calibrated on the other channel. Both channels simultaneously view the laser-produced plasma x-ray source from the same angle with respect to the laser beam and the planar target normal. Image plate detectors are calibrated for the first time at photon energies below 700 eV. Single shot simultaneous calibration of several detectors is possible, making this method an efficient and practical way to periodically calibrate detectors, using in-house capabilities of laser laboratories.

Hydroxyl radical mediated damage of proteins in low oxygen solution investigated using X-ray footprinting mass spectrometry.

In the method of X-ray footprinting mass spectrometry (XFMS), proteins at micromolar concentration in solution are irradiated with a broadband X-ray source, and the resulting hydroxyl radical modifications are characterized using liquid chromatography mass spectrometry to determine sites of solvent accessibility. These data are used to infer structural changes in proteins upon interaction with other proteins, folding, or ligand binding. XFMS is typically performed under aerobic conditions; dissolved molecular oxygen in solution isnecessary in many, if not all, the hydroxyl radical modifications that are generally reported. In this study we investigated the result of X-ray induced modifications to three different proteins under aerobic versus low oxygen conditions, and correlated the extent of damage with dose calculations. We observed a concentration-dependent protecting effect at higher protein concentration for a given X-ray dose. For the typical doses used in XFMS experiments there was minimal X-ray induced aggregation and fragmentation, but for higher doses we observed formation of covalent higher molecular weight oligomers, as well as fragmentation, which was affected by the amount of dissolved oxygen in solution. The higher molecular weight products in the form of dimers, trimers, and tetramers were present in all sample preparations, and, upon X-ray irradiation, these oligomers became non-reducible as seen in SDS-PAGE. The results provide an important contribution to the large body of X-ray radiation damage literature in structural biology research, and will specifically help inform the future planning of XFMS, and well as X-ray crystallography and small-angle X-ray scattering experiments.

Microcoulomb (0.7 \xb1 frac{0.4}{0.2} \u03bcC) laser plasma accelerator on OMEGA EP

Laser-plasma accelerators (LPAs) driven by picosecond-scale, kilojoule-class lasers can generate particle beams and x-ray sources that could be utilized in experiments driven by multi-kilojoule, high-energy-density science (HEDS) drivers such as the OMEGA laser at the Laboratory for Laser Energetics (LLE) or the National Ignition Facility at Lawrence Livermore National Laboratory. This paper reports on the development of the first LPA driven by a short-pulse, kilojoule-class laser (OMEGA EP) connected to a multi-kilojoule HEDS driver (OMEGA). In experiments, electron beams were produced with electron energies greater than 200 MeV, divergences as low as 32 mrad, charge greater than 700 nC, and conversion efficiencies from laser energy to electron energy up to 11%. The electron beam charge scales with both the normalized vector potential and plasma density. These electron beams show promise as a method to generate MeV-class radiography sources and improved-flux broadband x-ray sources at HEDS drivers.

Broadband X-ray ptychography using multi-wavelength algorithm.

Ptychography is a rapidly developing scanning microscopy which is able to view the internal structures of samples at a high resolution beyond the illumination size. The achieved spatial resolution is theoretically dose-limited. A broadband source can provide much higher flux compared with a monochromatic source; however, it conflicts with the necessary coherence requirements of this coherent diffraction imaging technique. In this paper, a multi-wavelength reconstruction algorithm has been developed to deal with the broad bandwidth in ptychography. Compared with the latest development of mixed-state reconstruction approach, this multi-wavelength approach is more accurate in the physical model, and also considers the spot size variation as a function of energy due to the chromatic focusing optics. Therefore, this method has been proved in both simulation and experiment to significantly improve the reconstruction when the source bandwidth, illumination size and scan step size increase. It is worth mentioning that the accurate and detailed information of the energy spectrum for the incident beam is not required in advance for the proposed method. Further, we combine multi-wavelength and mixed-state approaches to jointly solve temporal and spatial partial coherence in ptychography so that itcan handle various disadvantageous experimental effects. The significant relaxation in coherence requirements by our approaches allows the use of high-flux broadband X-ray sources for high-efficient and high-resolution ptychographic imaging.

Development of Container Free Sample Exposure for Synchrotron X-ray Footprinting.

The method of X-ray footprinting and mass spectrometry (XFMS) on large protein assemblies and membrane protein samples requires high flux density to overcome the hydroxyl radical scavenging reactions produced by the buffer constituents and the total protein content. Previously, we successfully developed microsecond XFMS using microfluidic capillary flow and a microfocused broadband X-ray source at the Advanced Light Source synchrotron beamlines, but the excessive radiation damage incurred when using capillaries prevented the full usage of a high-flux density beam. Here we present another significant advance for the XFMS method: the instrumentation of a liquid injection jet to deliver container free samples to the X-ray beam. Our preliminary experiments with a liquid jet at a bending magnet X-ray beamline demonstrate the feasibility of the approach and show a significant improvement in the effective dose for both the Alexa fluorescence assay and protein samples compared to conventional capillary flow methods. The combination of precisely controlled high dose delivery, shorter exposure times, and elimination of radiation damage due to capillary effects significantly increases the signal quality of the hydroxyl radical modification products and the dose-response data. This new approach is the first application of container free sample handling for XFMS and opens up the method for even further advances, such as high-quality microsecond time-resolved XFMS studies.

X-ray absorption near edge spectroscopy study of warm dense MgO

We report time-resolved X-ray Absorption Near Edge Spectroscopy (XANES) measurements of warm dense MgO. We used a high power nanosecond pulse to drive a strong uniform shock wave into an MgO sample, and a picosecond pulse to generate a broadband X-ray source near the Mg K-edge. We used this setup to obtain XANES spectra across a large area of the phase diagram, with densities up to 6.8 g/cc and temperatures up to 30 000 K, conditions at which no prior investigations of electronic and ionic structure exist. Our XANES results, together with quantum molecular dynamic simulations, demonstrate that the sample metallizes due to the bandgap closure as it melts, after which it shows typical behavior for a disordered ionic liquid.

X-ray analysis methods for sources from self-modulated laser wakefield acceleration driven by picosecond lasers.

A versatile set of methods for analyzing x-ray energy spectra and photon flux has been developed for laser plasma accelerator experiments driven by picosecond lasers. Forward fit provides extrapolated broad energy spectrum measurements, while Ross pair and differential average transmission analysis provide directly measured data points using a particular diagnostic. Combining these methods allows the measurement of x-ray energy spectra with improved confidence. We apply the methods to three diagnostics (filter wheel, stacked image plate spectrometer, and step wedge), each sensitive to a different region of x-ray energies (<40 keV, 35-100 keV, and 60-1000 keV, respectively), to characterize the analysis methods using laser-driven bremsstrahlung x-rays. We then apply the methods to measure three x-ray mechanisms, betatron, inverse Compton scattering, and bremsstrahlung, driven by a laser plasma accelerator. The analysis results in the measurement of x-ray energy spectra ranging from 10 keV to 1 MeV with peak flux greater than 1010 photons/keV/Sr. The combined analysis methods provide a robust tool to accurately measure broadband x-ray sources (keV to MeV) driven by laser plasma acceleration with picosecond, kilojoule-class lasers.

Simultaneous X-ray diffraction, crystallography and fluorescence mapping using the Maia detector

Interactions between neighboring grains influence the macroscale behavior of polycrystalline materials, particularly their deformation behavior, damage initiation and propagation mechanisms. However, mapping all of the critical material properties normally requires that several independent measurements are performed. Here we report the first grain mapping of a polycrystalline foil using a pixelated energy-dispersive X-ray area detector, simultaneously measuring X-ray fluorescence and diffraction with the Maia detector in order to determine grain orientation and estimate lattice strain. These results demonstrate the potential of the next generation of X-ray area detectors for materials characterization. By scanning the incident X-ray energy we investigate these detectors as a complete solution for simultaneously mapping the crystallographic and chemical properties of the sample. The extension of these techniques to broadband X-ray sources is also discussed.

X-ray source development for EXAFS measurements on the National Ignition Facility.

Extended X-ray absorption Fine Structure (EXAFS) measurements require a bright, spectrally smooth, and broad-band x-ray source. In a laser facility, such an x-ray source can be generated by a laser-driven capsule implosion. In order to optimize the x-ray emission, different capsule types and laser irradiations have been tested at the National Ignition Facility (NIF). A crystal spectrometer is used to disperse the x-rays and high efficiency image plate detectors are used to measure the absorption spectra in transmission geometry. EXAFS measurements at the K-edge of iron at ambient conditions have been obtained for the first time on the NIF laser, and the requirements for optimization have been established.

Spectral tailoring of nanoscale EUV and soft x-ray multilayer optics

Extreme ultraviolet and soft X-ray (XUV) multilayer optics have experienced significant development over the past few years, particularly on controlling the spectral characteristics of light for advanced applications like EUV photolithography, space observation, and accelerator- or lab-based XUV experiments. Both planar and three dimensional multilayer structures have been developed to tailor the spectral response in a wide wavelength range. For the planar multilayer optics, different layered schemes are explored. Stacks of periodic multilayers and capping layers are demonstrated to achieve multi-channel reflection or suppression of the reflective properties. Aperiodic multilayer structures enable broadband reflection both in angles and wavelengths, with the possibility of polarization control. The broad wavelength band multilayer is also used to shape attosecond pulses for the study of ultrafast phenomena. Narrowband multilayer monochromators are delivered to bridge the resolution gap between crystals and regular multilayers. High spectral purity multilayers with innovated anti-reflection structures are shown to select spectrally clean XUV radiation from broadband X-ray sources, especially the plasma sources for EUV lithography. Significant progress is also made in the three dimensional multilayer optics, i.e., combining micro- and nanostructures with multilayers, in order to provide new freedom to tune the spectral response. Several kinds of multilayer gratings, including multilayer coated gratings, sliced multilayer gratings, and lamellar multilayer gratings are being pursued for high resolution and high efficiency XUV spectrometers/monochromators, with their advantages and disadvantages, respectively. Multilayer diffraction optics are also developed for spectral purity enhancement. New structures like gratings, zone plates, and pyramids that obtain full suppression of the unwanted radiation and high XUV reflectance are reviewed. Based on the present achievement of the spectral tailoring multilayer optics, the remaining challenges and opportunities for future researches are discussed.

Determination of the reflectivity curve of a spherically bent mica crystal used to diagnose X-ray radiation of relativistic laser plasma

A method for determining the crystal reflectivity curve, based on the use of a broadband X-ray source and an additional spectrometer with preliminarily measured characteristics is proposed. Such a technique does not allow determination of the absolute reflectivity, but makes it possible to measure the dependence of its relative values on the wavelength. Using X-ray radiation of relativistic dense laser plasma, the reflection curve of a spherically bent mica crystal is measured in the range of 6.7–8.7 A. The obtained reflectivity curve is used to correctly interpret X-ray spectra of dense plasma generated during the interaction a petawatt laser pulse with solid targets.

Quantitative imaging of single-shot liquid distributions in sprays using broadband flash x-ray radiography

Flash x-ray radiography is used to capture quantitative, two-dimensional line-of-sight averaged, single-shot liquid distribution measurements in impinging jet sprays. The accuracy of utilizing broadband x-ray radiation from compact flash tube sources is investigated for a range of conditions by comparing the data with radiographic high-speed measurements from a narrowband, high-intensity synchrotron x-ray facility at the Advanced Photon Source (APS) of Argonne National Laboratory. The path length of the liquid jets is varied to evaluate the effects of energy dependent x-ray attenuation, also known as spectral beam hardening. The spatial liquid distributions from flash x-ray and synchrotron-based radiography are compared, along with spectral characteristics using Taylor's hypothesis. The results indicate that quantitative, single-shot imaging of liquid distributions can be achieved using broadband x-ray sources with nanosecond temporal resolution. Practical considerations for optimizing the imaging system performance are discussed, including the coupled effects of x-ray bandwidth, contrast, sensitivity, spatial resolution, temporal resolution, and spectral beam hardening.

High-pressure structural changes in liquid silica.

The structural properties of liquid silica at high pressure and moderate temperature conditions, also referred to as the warm dense matter regime, were investigated using time-resolved K-edge x-ray absorption spectroscopy and ab initio calculations. We used a nanosecond laser beam to compress uniformly a solid SiO_{2} target and a picosecond laser beam to generate a broadband x-ray source. We obtained x-ray absorption spectra at the Si K edge over a large pressure-temperature domain to probe the liquid phase up to 3.6 times the normal solid density. Using ab initio simulations, we are able to interpret the changes in the x-ray absorption near-edge structure with increasing densities as an increase in the coordination number of silicon by oxygen atoms from 4 to 9. This indicates that, up to significant temperatures, the liquid structure becomes akin to what is found in the solid SiO_{2} phases.

Metallization of warm dense SiO(2) studied by XANES spectroscopy.

We investigate the evolution of the electronic structure of fused silica in a dense plasma regime using time-resolved x-ray absorption spectroscopy. We use a nanosecond (ns) laser beam to generate a strong uniform shock wave in the sample and a picosecond (ps) pulse to produce a broadband x-ray source near the Si K edge. By varying the delay between the two laser beams and the intensity of the ns beam, we explore a large thermodynamical domain with densities varying from 1 to 5 g/cm^{3} and temperatures up to 5eV. In contrast to normal conditions where silica is a well-known insulator with a wide band gap of 8.9eV, we find that shocked silica exhibits a pseudogap as a semimetal throughout this thermodynamical domain. This is in quantitative agreement with density functional theory predictions performed using the generalized gradient approximation.

Characterization of an indirect X-ray imaging detector by simulation and experiment.

We describe a comprehensive model of a commercial indirect X-ray imaging detector that accurately predicts the detector point spread function and its dependence on X-ray energy. The model was validated by measurements using monochromatic synchrotron radiation and extended to polychromatic X-ray sources. Our approach can be used to predict the performance of an imaging detector and can be used to optimize imaging experiments with broad-band X-ray sources.

Evaluation of X-ray sources for quantitative two- and three-dimensional imaging of liquid mass distribution in atomizing sprays

Quantitative measurement of liquid mass distribution is demonstrated in an impinging-jet atomizing spray using a broadband, ∼80keV X-ray tube source for 2-D radiography and 3-D computed tomography (CT). The accuracy, precision, and sensitivity of these data are evaluated using narrowband, ∼10keV, synchrotron radiation from the Argonne National Laboratory Advanced Photon Source (APS) at the same flow conditions. It is found that the broadband X-ray tube source can be used for 2-D measurement of the equivalent path length (EPL) and 3-D CT imaging of liquid mass distribution with typical error of 5–10%. Data are compared for cases with and without the use of potassium iodide (KI), which at 15% concentration by mass increases the attenuation coefficient eightfold and enables 2-D and 3-D measurement of EPL with a signal-to-noise ratio (SNR) of 5:1 down to 15μm. At this concentration, the effects of energy-dependent attenuation (i.e., spectral beam hardening) are negligible for EPL up to 5mm. Hence, the use of broadband X-ray tube sources is feasible for many practical engineering sprays with a dynamic range in EPL of ∼330:1. The advantages and limitations of using broadband and narrowband X-ray sources are discussed, and recommendations for improving performance are presented.

X-ray phase contrast imaging and noise evaluation using a single phase grating interferometer

In this paper we present some quantitative measurements of X-ray phase contrast images and noise evaluation obtained with a recent grating based X-ray phase contrast interferometer. This device is built using a single phase grating and a large broadband X-ray source. It was calibrated using a reference sample and finally used to perform measurements of a biological fossil: a mosquito trapped in amber. As phase images, noise was evaluated from the measured interferograms.

A technique for measuring the propagation of a supersonic radiation front in foam via spatially resolved spectral imaging of a tracer layer

We present a technique for measuring the propagation of a supersonic radiation front in low-density foam, where the lack of motion of the objects in its wake makes it difficult to determine its location. We illuminate a thin tracer foil embedded in the foam with a broadband x-ray source, and measure its changing absorption of these x rays as it ionizes. We record both spatial and spectral information of the heated tracer, and thus obtain its ionization state as a function of distance along the front propagation direction. We extrapolate this information to determine the state of the foam and the location of the radiation front. We present the experimental configuration used to test this technique at the Omega laser facility along with experimental results.