Anode For Lithium-ion Batteries Research Articles

Fluorinated reduced graphene oxide nanosheets for symmetric supercapacitor device performance

This study explores the potential of using spent lithium-ion battery anodes (graphite) for fabricating symmetric energy devices through a simple regeneration process. Specifically, the use of fluorine-doped reduced graphene oxide (RGO) nanosheets derived from waste batteries as the basis for a symmetric supercapacitor (SC) device is investigated. To enhance the electrochemical energy storage capabilities, a facile hydrothermal technique is employed to synthesize fluorinated graphene. Fluorination of the graphene sheets is successfully realized, as confirmed by the presence of boron with a 2.94 at.% fluorine-doped level, according to the Energy dispersive spectroscopy (EDS) spectrum analysis. Electrochemical analysis of the F-RGO electrode performance consistent with electric double-layer capacitance. Moreover, with a three-electrode system, the F-RGO electrode achieves a maximum specific capacitance of 207F/g under a current density of 1 A/g. A two-electrode symmetric device employing F-RGO exhibits a specific capacitance of 54F/g at 1 A/g. Furthermore, electrochemical impedance measurements demonstrate low charge transfer resistance (Rct) values, specifically 8.63 Ω for F-RGO, signifying improved electrochemical performance. Thus, fluorine atomic doping in RGO nanosheets contributes to the improvements of the specific capacitance and overall superior electrochemical performance of F-RGO, and F-RGO is a highly electrochemical active material for high-performance energy storage electrodes for SCs.

Advances in Coating Materials for Silicon-Based Lithium-Ion Battery Anodes

Silicon anodes, which exhibit high theoretical capacity and very low operating potential, are promising as anode candidates that can satisfy the conditions currently required for secondary batteries. However, the low conductivity of silicon and the alloying/dealloying phenomena that occur during charging and discharging cause sizeable volume expansion with side reactions; moreover, various electrochemical issues result in inferior cycling performance. Therefore, many strategies have been proposed to mitigate these problems, with the most commonly used method being the use of nanosized silicon. However, this approach leads to another electrochemical limitation—that is, an increase in side reactions due to the large surface area. These problems can effectively be resolved using coating strategies. Therefore, to address the issues faced by silicon anodes in lithium-ion batteries, this review comprehensively discusses various coating materials and the related synthesis methods. In this review, the electrochemical properties of silicon-based anodes are outlined according to the application of various coating materials such as carbon, inorganic (including metal-, metal oxide-, and nitride-based) materials, and polymer. Additionally, double shells introduced using two materials for double coatings exhibit more complementary electrochemical properties than those of their single-layer counterparts. The strategy involving the application of a coating is expected to have a positive effect on the commercialization of silicon-based anodes.

A Fast Self-Healing Binder for Highly Stable SiOx Anodes in Lithium-Ion Batteries.

Silicon oxide-based (SiOx-based) materials show great promise as anodes for high-energy lithium-ion batteries due to their high specific capacity. However, their practical application is hindered by the inevitable volumetric expansion during the lithiation/delithiation process. Constructing high-performance binders for SiOx-based anodes has been regarded as an efficient strategy to mitigate their volume expansion and preserve structural integrity. In this work, we propose a green water-solution PAA-LS binder composed of poly(acrylic acid) (PAA) and sodium lignosulfonate (LS) with fast self-healing properties. The designed binder can be restored due to the strong affinity between Fe3+-catechol coordination bonds, thereby effectively alleviating the volumetric strain of SiOx-based anodes. Notably, with an optimized LS content of 0.5%, the SiOx@PAA-LS electrode exhibits excellent performance, delivering a high capacity of 997.3 mAh g-1 after 450 cycles at 0.5 A g-1. Furthermore, the SiOx||NCM622 full cell also demonstrates superior cycling stability, maintaining a discharge capacity of 147.58 mAh g-1 after 100 cycles at 0.5 A g-1, with an impressive capacity retention rate of 82.72%.

Dramatic Enhancement Enabled by Introducing TiN into Bread-like Porous Si-Carbon Anodes for High-Performance and Safe Lithium Storage.

Doping modifications and surface coatings are effective methods to slow volume dilatation and boost the conductivity in silicon (Si) anodes for lithium-ion batteries (LIBs). Herein, using low-cost ferrosilicon from industrial production as the energy storage material, a bread-like nitrogen-doped carbon shell-coated porous Si embedded with the titanium nitride (TiN) nanoparticle composite (PSi/TiN@NC) was synthesized by simple ball milling, etching, and self-assembly growth processes. Remarkably, the porous Si structure formed by etching the FeSi2 phase in ferrosilicon alloys can provide buffer space for significant volume expansion during lithiation. Highly conductive and stable TiN particles can act as stress absorption sites for Si and improve the electronic conductivity of the material. Furthermore, the nitrogen-doped porous carbon shell further helps to sustain the structural stability of the electrode material and boost the migration rate of Li-ions. Benefiting from its unique synergistic effect of components, the PSi/TiN@NC anode exhibits a reversible discharge capacity up to 1324.2 mAh g-1 with a capacity retention rate of 91.5% after 100 cycles at 0.5 A g-1 (vs fourth discharge). Simultaneously, the electrode also delivers good rate performance and a stable discharge capacity of 923.6 mAh g-1 over 300 cycles. This research can offer a potential economic strategy for the development of high-performance and inexpensive Si-based anodes for LIBs.

Carbon matrix NiFeP/C nanoparticles anchored on Ti3C2Tx nanosheets as heterostructure high-performance anode for lithium-ion batteries

Engineered micro-nano heterogeneous architectures for transition metal phosphide (TMPs) anode materials in lithium-ion batteries (LIBs) provide multifunctional active components. These components synergistically interact to address pivotal challenges of pronounced volume expansion and sluggish reaction kinetics within the electrode. Consequently, this engineering design approach significantly enhances the overall battery performance. In this study, a self-assembled approach is employed to integrate hybridized NiFe-PBA nanocubes with two-dimensional (2D) monolayer MXene (Ti3C2Tx), producing a heterostructured NiFeP/C@Ti3C2Tx composite. In this meticulously engineered architecture, the interface between the outer MXene layer and NiFeP embedded within the carbon matrix exhibits several distinct superiorities, such as rapid interfacial ion migration, multidirectional migration pathways, and strong spatial adaptability. The resulting non-uniform phase structure effectively mitigates electrode expansion and enhances electronic conductivity. Consequently, the NiFeP/C@Ti3C2Tx-15 composite demonstrates distinct performance advantages over NiFeP/C without MXene. The composite achieves a specific capacity of 689.4 mAh g⁻¹ at 200 mA g⁻¹ over 300 cycles, double that of NiFeP/C. Furthermore, density functional theory (DFT) calculations validate the electronic conductivity facilitated by the heterointerface between MXene and NiFeP, substantiating the strategic significance of the heterostructure in advancing high-performance anode materials for lithium-ion batteries.

Novel High-Entropy oxide Achieves high capacity and stability as an anode for Lithium-Ion batteries

High-entropy oxides possess high theoretical capacity, stable chemical structure, making them highly promising as battery electrode materials. The limited successful synthesis of high-entropy oxide systems has hindered their further development. This study synthesized a six-component high-entropy spinel oxide (FeCoMgCrLiZn)3O4 for the first time and evaluated its electrochemical performance as an anode for lithium-ion batteries. The data show that this single-phase oxide exhibits a high reversible capacity (stabilizing at 800 mAh/g after 300 cycles at 200 mA/g), good cycling stability (800 stable cycles at 2000 mA/g without significant capacity decay), and excellent rate performance. This study expands the high-entropy oxide family and provides a potential strategy for developing next-generation energy storage materials.

Synergistic Structural Integrity and Remarkable Structural Stability of NC@Si Anodes for Lithium-ion Batteries

The silicon-based anode has attracted wide attention because of its high theoretical specific capacity, which is expected to greatly improve the batteries’ energy density. However, during the charge-discharge cycles, the great volume expansion of the anode active silicon seriously restricts its electrochemical stability. Herein, N-doping carbon-coated silicon microsphere was prepared for lithium-ion batteries. Benefit from the core-shell structure formed from silicon carbon, the volume change of silicon anode during the cycle is well coordinated. What's more, N-doping carbon reduces the reaction energy barrier between silicon and lithium and accelerates the electrochemical reaction, which improves the cycling performance of the battery. The specific capacity of the prepared button battery is as high as 2913.13 mAh g−1 at the current density of 0.21 mA g−1, and the average coulomb efficiency is higher than 99.84% during the cycling. And the capacity of NC@SiO2 anode gradually stabilizes after 500 cycles.

Iron-based bimetallic oxide carbon composites with superior lithium storage capabilities serve as anode in lithium-ion batteries

Transition metal oxides (TMOs) have emerged as highly promising electrode materials for lithium-ion batteries (LIBs) owing to their versatile valence states and distinctive morphological attributes. Bimetallic oxides, in particular, exhibit the ability to mitigate the volume expansion associated with lithium alloying and de-alloying processes. Despite these advantages, metal oxides often suffer from drawbacks such as poor conductivity, limited cycle stability, and a propensity for lithiation. Addressing the challenges of low electronic conductivity, significant volume expansion, and inadequate uniformity, we synthesized two bimetallic oxide-based carbon composites via a “one-pot” solvothermal approach: ZnFe2O4@C and MnFe2O4@C. These composites are enveloped in a carbon shell derived from anhydrous ethanol. Notably, the specific discharge capacities of ZnFe2O4@C and MnFe2O4@C surpass those of their respective single metal oxide counterparts. Following nearly 300 cycles of charge and discharge operations at a current density of 100 mA g−1, ZnFe2O4@C exhibited a specific discharge capacity of 1528 mAh g−1, while MnFe2O4@C demonstrated a capacity of 1283 mAh g−1. The synthesis method offers simplicity, high yield, and uniform morphology, making it a promising avenue for enhancing the performance of LIBs electrode materials.

Synthesis, Characterization and Electrochemical Performance of Bi2S3/Rice Husk-Based Activated Carbon Composites As Lithium Ion Battery Anodes

This study investigates the impact of hydrothermal duration on bismuth sulfide/activated carbon composites (Bi2S3/AC) by varying the duration to 8, 24, and 48 hours. The primary aim is to delineate the composite characteristics and electrochemical performance of Bi2S3/AC composites, aiming to produce anodes for lithium-ion batteries with high capacity, excellent cyclic stability, and minimal volume expansion. Activated carbon derived from rice husks was synthesized via a carbonization process and chemical activation using H3PO4 as an activator. Subsequently, the synthesis of Bi2S3/AC composites used bismuth nitrate pentahydrate and thiourea precursors through the hydrothermal method that involved three variations of hydrothermal duration: 8, 24, and 48 hours, denoted as BC8, BC24, and BC48, respectively. The FTIR test indicates the presence of Bi-S, C=C, and C-O groups in the three composite products, signifying the existence of bismuth sulfide and activated carbon. The XRD result reveals orthorhombic crystal forms in the composites, while the SEM-EDX mapping illustrates particle morphologies resembling flower-like shapes. These compositions comprise Bi 74.16%, S 11.37%, and C 10.43%. The GSA test suggests a mesoporous pore size in these composites. In final result, BC24 exhibits the highest electrical and ionic conductivity, measuring 2.12 × 10−3 S.cm−1 and 2.057 × 10−4 S.cm−1, respectively. The CV data of the BC24 composite indicates two reduction and oxidation peaks in the first cycle. Charge-discharge test on the BC24 composite exhibits a specific charge capacity of 445.51 mAh/g and a discharge capacity of 364.24 mAh/g.

Investigation on melt growth (Mg, Co, Ni, Cu, Zn)O oxide ceramics prepared by laser directed energy deposition

High-entropy oxides (HEOs) have attracted extensive research interest due to their unique structural features, customizable elemental compositions, and tunable functional properties. Nevertheless, the complexity, low efficiency, and high cost of the existing HEO synthesis methods place limitations on them. In this study, Laser directed energy deposition (LDED) was employed to synthesize (Mg, Co, Ni, Cu, Zn)O oxides. Additionally, the novelty of applying the LDED process to multicationic systems was emphasized. The comparison between specimens fabricated from mixed powder via LDED(MP) and those fabricated from pre-sintered powder via LDED(SP) encompasses macroscopic morphology, microstructure, and performance. The results showed that SP significantly enhanced the density from 86.44% to 96.70% compared to MP. The macro-segregation of Cu and Cu2O in the phase composition was observed in MP and SP. High-temperature pre-sintering promoted the solid solution formation of Co and Ni during LDED, leading to more severe micro-segregation of Co and Ni. When employed as anodes in lithium-ion batteries, MP and SP have outstanding long-term cycle stability, according to electrochemical performance studies. At a current density of 100 mAg-1, these specimens maintained a capacity retention rate of 100% even after 200 cycles. The initial discharge capacities of MP and SP were respectively 477.73 mAh g-1 and 373.86 mAh g-1. This study is expected to present a novel approach for the rapid synthesis of (Mg, Co, Ni, Cu, Zn)O oxide ceramics.

Nitrogen‑sulfur doped graphene-loaded SiO2/Co9S8 composites as anode materials for improved lithium storage

Heteroatom-doped graphene lamellae can effectively modulate the physical and chemical surface activities of Co9S8 materials. The addition of a second dopant atom, such as nitrogen (N) can further improve the composite properties. Herein, novel nitrogen‑sulfur double-doped graphene-loaded SiO2/Co9S8 composites (SiO2/Co9S8@NSG) were prepared by a one-step solvothermal method using polyethylene glycol as the carbon source and cobalt chloride hexahydrate as the cobalt source to yield a Deep Eutectic Solvents (DESs) system. The precursor was then obtained by adding tetraethyl silicate as the silicon source, thiourea as the sulfur source, and urea as the nitrogen source. The uniform distribution of Co9S8 in the N/S-doped graphene matrix formed graphene-coated SiO2 particles SiO2/Co9S8@NSG with high specific surface area, superior ionic conductivity, and elevated theoretical specific capacity. The N/S co-doped graphene matrix not only improved the electrical conductivity and hindered the adhesion of the particles, but also buffered the volume of the Co9S8 change and enhanced the electrochemical performance. The testing of SiO2/Co9S8@NSG composite as an anode for lithium-ion batteries (LIBs) revealed an impressive specific capacity with reversible capacity of 850 mA h/g after 900 cycles at a current density of 0.5 A/g and multiplicative capacity of 730 mA h/g at a current density of 0.1 A/g, confirming excellent cycling stability and a Coulombic efficiency close to 100 %. Overall, the proposed doping strategy looks promising for the development of high-performance LIBs.

Coal-based Si self-doped disordered porous carbon for supercapacitor electrodes

In preparing activated carbon for coal-based supercapacitors, silicon in coal usually requires removal with hydrofluoric acid, which is neither economical nor environmentally friendly. However, silicon can be used as the anode in lithium batteries due to its high theoretical capacity. So silicon was retained to study its effect on supercapacitors. By retaining silicon without hydrofluoric acid treatment and activating at lower temperature, the prepared Si-doped activated carbon achieved a high specific capacitance of 318.3F/g at 0.5 A/g in the three-electrode test system. Omitting hydrofluoric acid treatment increased the specific capacitance by 49 %. Experimental results show that this 4.92 % silicon doping, mainly CSiO3, is the main reason for the enhancement. Density functional theory (DFT) simulations confirmed that CSiO3 improves double-layer capacitance by localizing surface charge and enhancing electrolyte ion adsorption, while also boosting quantum capacitance. High activation temperatures increase coal-activator reactions but also decrease disorder of the carbon, reducing specific capacitance. Temperature experiments show that the specific capacitance increases and then decreases in the range of 600 ∼ 950 °C, and reaches a peak at 650 °C. This study presents a simple, effective method to enhance supercapacitor performance with silicon-carbon precursors and provides detailed explanation on the capacitance enhancement mechanism for the first time.

VS2/ Blue Phosphorus composites for high speed lithium ions storage

Based on first-principles calculations, the potential of the H-VS2/Blue P heterojunction composite as a lithium-ion battery anode is systematically investigated. This heterojunction composite enhances the stability of the VS2 structure and increases its overall mechanical strength.The Young's modulus of the composite is 144.69 N/m, markedly exceeding that of the single layer. Furthermore, it modifies the electronic properties of the Blue P monolayer, converting it from an insulating to a metallic state.The H-VS2/Blue P heterojunction composite exhibits a high lithium adsorption energy of 4.34 eV and a low diffusion barrier of 0.15-0.19 eV, facilitating rapid lithium-ion migration during charge/discharge cycles. And the theoretical capacity of the heterojunction composite is up to 1211 mAh/g. The combination of elevated adsorption energy, low diffusion barrier, and high theoretical capacity indicates that the H-VS2/Blue P heterojunction composite is a highly promising anode material for lithium-ion batteries.

High-capacity and long-life Fe2O3/MOFs composite anodes: Preparation, characterization, morphology regulation and electrochemical performance

Among the various transition metal oxides used in lithium-ion battery anodes, iron oxide (Fe2O3) has received extensive attention due to its low cost, good environmental compatibility and high theoretical capacity. However, the volume expansion and structural collapse during the charging-discharging cycling process significantly limited the practical application of Fe2O3. Herein, we demonstrate enhanced electrochemical properties and stability of Fe2O3 by anchoring it on metal-organic frameworks (MOFs). Through adjusting the MOF ligands and introducing humic acid (HA), we reached rational control of the morphology for the Fe2O3/MOF composites. The optimized sample, namely Fe2O3@HA-Fe-ATA, shows 3D cauliflower-like structure with abundant pores, which are beneficial to the active sites exposure, electrolyte penetration, as well as the tolerance toward volume expansion. Consequently, high reversible capacity of 1442.7 mAh g−1 (at 0.1 A g−1), excellent rate performance (<11 % capacity decrease when current density increases from 0.1 A g−1 to 1 A g−1), and satisfactory cycle stability (91 % capacity retention after 500 cycles at 1 A g−1) are obtained. This work demonstrates that the rational design of MOF by introduction of appropriate ligand is a very efficient approach to optimize the electrochemical properties of the resultant electrode material.

Self-Standing vanadium oxide pillared carbon microfiber film as an excellent anode for lithium & sodium ion batteries

Insertion of substances (such as atoms/molecules/ions) into the interlayer spaces of graphite to increase its layer separation is found to be extremely useful for sodium-ion batteries (SIBs). Therefore, expanded graphitic systems are the obvious choice as anode material for both lithium/sodium-ion batteries (LIBs/SIBs). Hard carbon-based materials altogether give a decent electrochemical performance, as well as allow structural integrity for long-term use. Herein, we report a facile route to prepare free-standing vanadium oxide doped carbon microfibers (V@CMFs) films. The V@CMFs show ∼ 200 % expansion in the graphitic interlayer distances while accommodating minute deformations in the final compound which is further theoretically verified as the stage-1 type dilute graphite intercalation compound (GICs) with pillar-like structures. Best battery performance was obtained for the 1 % doped (V1@CMFs) sample, with an initial discharge capacity of 1501.8 and 703.4 mAhg−1, reversible capacities of 1253.8 and 288.7 mAhg−1 at 20 mAg−1, and rate capabilities i.e., 362.4 and 108.1 mAhg−1 at 1600 mAg−1, for LIBs and SIBs, respectively. The results revealed that the rate capability and the reversible specific capacity of the 1 % vanadium oxide doped carbon microfibers (V1@CMFs) are significantly superior compared to the pristine and previous reports. Here, the incorporation of just 1 % vanadium oxide acts as a pillar, enhancing the stability and conductivity of the carbon. Thus, the present work highlights the utility of molecularly doped GICs as potential anode materials for LIBs/SIBs.

Porous silicon/carbon composites as anodes for high-performance lithium-ion batteries

Silicon anodes are promising for use in lithium-ion batteries. However, their practical application is severely limited by their large volume expansion leading to irreversible material fracture and electrical disconnects. This study proposes a new top-down strategy for preparing microsize porous silicon and introduces polyacrylonitrile (PAN) for a nitrogen-doped carbon coating, which is designed to maintain the internal pore volume and lower the expansion of the anode during lithiation and delithiation. We then explore the effect of temperature on the evolution of the structure of PAN and the electrochemical behavior of the composite electrode. After treatment at 400 -, the PAN coating retains a high nitrogen content of 11.35%, confirming the presence of C―N and C―O bonds that improve the ionic-electronic transport properties. This treatment not only results in a more intact carbon layer structure, but also introduces carbon defects, and produces a material that has remarkable stable cycling even at high rates. When cycled at 4 A g−1, the anode had a specific capacity of 857.6 mAh g−1 even after 200 cycles, demonstrating great potential for high-capacity energy storage applications.

Incorporation of SnSe2/SnO2 heterostructures in carbon nanotubes for excellent lithium storage performance

As a new type of negative electrode material, tin-based material exhibits a high theoretical capacity. However, tin-based anode materials always undergo severe volume change upon alloying reaction during lithium insertion and extraction, which leads to the pulverization of the active materials and poor electrochemical performance, seriously hampering its practical application. In this work, oxygen-containing group functionalized carbon nanotubes (FCNTs) were facilely obtained, and the three-dimensional crosslinked SnSe2-SnO2@FCNTs multiphase materials were prepared by solvothermal and high-temperature heat treatment. The formation of Sn-O-C bonds from oxygen-containing functional groups of FCNTs combined with Sn can promote the electric connection and integrity of the composites. The implanted defects in FCNTs can not only be beneficial to anchoring SnO2 and SnSe2 nanoparticles, but also helpful to the penetration of Li+ ions into the electrodes from electrolyte. In addition, the large Fermi energy difference between SnSe2 and SnO2 nanoparticles results in the formation of a built-in electric field at the interface of the multiphase materials, accelerating the diffusion of ions. The smaller size of the multiphase materials leads to significant pseudocapacitive behavior, which facilitates the highly reversible surface/interface adsorption. Under the multiple effects of FCNTs, SnSe2, and SnO2, the SnSe2-SnO2@FCNTs multiphase materials exhibited excellent electrochemical performance. At a current density of 0.1A·g-1, a discharge specific capacity of 898.0mAh·g-1 was achieved. When the current density was increased to 2A·g-1, it still exhibited a discharge specific capacity of 443.9mAh·g-1. After a long charge/discharge cycling at 1A·g-1 over 450 cycles, it still showed a specific capacity of ~ 400mAh·g-1. This work significantly demonstrated the enhanced Li-storage performance of SnSe2-SnO2 heterostructures incorporated in the functionalized multi-walled CNTs. This opens a new way to synthesize advanced tin-based materials as high-performance anodes for high-energy density lithium-ion batteries.

Enhancing performance of Si/C composite anode in high energy density lithium-ion batteries with CMC-CPAM-SBR binder

Abstract The utilization of polymeric binders is indispensable in the implementation of silicon/carbon anode materials in high-energy-density lithium-ion batteries (LIBs). This necessity arises from their pivotal function in upholding structural integrity. However, current water-based binders solely focus on binder adhesion, neglecting the crucial interaction with the carbon material. In this work, a composite binder (CMC-CPAM-SBR) was constructed by combining Styrene Butadiene Rubber (SBR) with cationic polyacrylamide (CPAM) network binder with self-healing carboxymethyl cellulose (CMC). This innovative binder formulation was designed to enhance the performance of Si@C/graphite composite anodes. A capacity retention rate of 92.86% was achieved after 100 cycles, which represents the improvement over the performance of electrodes utilizing the CMC-CPAM binder, which only retained a capacity of 84.53% after the same number of cycles. A full battery with a capacity of 1992.8 mAh was designed, and the battery capacity remained at 80.6% of its capacity after completing 500 cycles. This research presents an effective technique for manufacturing high-performance anode materials.

3D-Printed Carbon Scaffold for Structural Lithium Metal Batteries.

Focus on advancement of energy storage has now turned to curbing carbon emissions in the transportation sector by adopting electric vehicles (EVs). Technological advancements in lithium-ion batteries (LIBs), valued for their lightweight and high capacity, are critical to making this switch a reality. Integrating structurally enhanced LIBs directly into vehicular design tackles two EV limitations: vehicle range and weight. In this study, 3D-carbon (3D-C) lattices, prepared with an inexpensive stereolithography-type 3D printer followed by carbonization, are proposed as scaffolds for Li metal anodes for structural LIBs. Mechanical stability tests revealed that the 3D-C lattice can withstand a maximum stress of 5.15 ± 0.15MPa, which makes 3D-C lattices an ideal candidate for structural battery electrodes. Symmetric cell tests show the superior cycling stability of 3D-C scaffolds compared to conventional bare Cu foil current collectors. When 3D-C scaffolds are used, a small overpotential (≈0.075V) is retained over 100 cycles at 1mA cm-2 for 3 mAh cm-2, while the overpotential of a bare Cu symmetric cell is unstable and increased to 0.74V at the 96th cycle. The precisely oriented internal pores of the 3D-C lattice confine lithium metal deposits within the 3D scaffold, effectively preventing short circuits.

Core-shell structure and high rate performance of Ce-doped Li4Ti5O12 for lithium-ion battery anode materials

Lithium titanate (LTO) can be a very promising anode material for lithium-ion batteries (LSBs) due to its inherent ability to inhibit the growth of lithium dendrites as well as its unique “zero-strain” properties. Unfortunately, the low electronic conductivity of LTO leads to serious shortcomings in higher electrochemical demands. In this work, the Ce3+-doped C@Li4Ti5-xCexO12 (x = 0, 0.1, 0.15 and 0.2) anode materials synthesized by the hydrothermal method using carbon spheres as templates showed more significant improvement in both structural and electrochemical properties. The results demonstrate that electronic conductivity, lithium-ion diffusion rate, discharge specific capacity, discharge rate capability, and significant improvement stability of C@Li4Ti5-xCexO12 (x = 0.1, 0.15 and 0.2) electrodes. Among them, C@Li4Ti4.85Ce0.15O12 electrode exhibits the highest initial discharge specific capacity (250.86 mAh/g) at 0.1C, which is 1.28-fold that of C@ Li4Ti5O12 (195.94 mAh/g), and initial discharge capacity from 205.96 mAh/g to 170.39 mAh/g after 500 cycles, corresponding to 82.7 % of the initial stable discharge capacity. The outstanding performance of C@Li4Ti4.85Ce0.15O12 can be attributed to the lower interfacial impedance, higher electronic conductivity, high oxygen vacancy concentration, and moderate amount of Ce3+ doping can enhance the electrochemical activity. In addition, carbon sphere surface defects shown to be effective in improving lithium-ion storage. This work demonstrates that Ce3+ doping is an effective method to improve the electrochemical performance of LTOs and provides a more effective guide for designing and optimizing anode electrode materials for lithium-ion batteries