Add-drop Multiplexer Research Articles

A Novel Approach to Realize of All Optical Frequency Encoded Dibit Based XOR and XNOR Logic Gates Using Optical Switches with Simulated Verification

Since last few decades optics has already proved its strong potentiality for conducting parallel logic, arithmetic and algebraic operations due to its super-fast speed in communication and computation. So many different logical and sequential operations using all optical frequency encoding technique have been proposed by several authors. Here, we have keened out all optical dibit representation technique, which has the advantages of high speed operation as well as reducing the bit error problem. Exploiting this phenomenon, we have proposed all optical frequency encoded dibit based XOR and XNOR logic gates using the optical switches like add/drop multiplexer (ADM) and reflected semiconductor optical amplifier (RSOA). Also the operations of these gates have been verified through proper simulation using MATLAB (R2008a).

Realization of Multicore Fiber Reconfigurable Optical Add–Drop Multiplexer

Space-division multiplexing (SDM) is a calling for devices that fully replace their single-mode fiber counterparts. Fast optical switches represent one such type of key devices. In this letter, we present a free-space optical add-drop multiplexer for multicore fiber (MCF) optical communications. Microelectromechanical mirrors were used as the optical switching element. We first detail the implementation steps leading to the proposed device and then characterize its performance in terms of crosstalk and insertion loss. Overall average crosstalk is around -38 dB, while insertion losses remain large. The device investigated here is another step towards the practical adoption of SDM for optical networks based on MCFs.

Bi-directional ROADM with one pair of N x N cyclic-AWGs for over N wavelength channels configuration

Abstract This paper presents a bidirectional optical add-drop multiplexer (BROADM) with permitting white spectral channels input in bidirectional configuration. The filter routing rule of array waveguide grating (AWG) is applied for the wavelength channels (WCs) that need to be added and dropped by using the corresponding tunable fiber Bragg gratings (FBGs). The other WCs pass through output by tuning FBG filter spectra away from the WCs. The bandwidth between two adjacent WCs of each pair of ports in AWG is wider than one channel spacing so that the filter spectra of FBG is tuned to free spectral range (FSR) region to realize the wavelength routing function without interfering other WCs. The WCs can be flexibly handled by installing the corresponding tunable FBG. Therefore, the proposed BROADM is more flexible and has higher transmission capacity in the optical network.

Investigating the Performance of Wavelength Division Multiplexing based RoF Optical Network with Dispersion Compensation Fiber

A Radio-over-Fiber (RoF) make use of the advantages of wireless communication system and optical networks. It uses optical fiber as a core technology due to the enormous advantages offered by it. Making use of mobility available by wireless communication. Dispersion management and modulation were investigated for two Channel-WDM optical communication systems. Dispersion compensating fibers (DCF) are used to compensate the positive dispersion accumulated over a protracted haul SMF between CS (central Site) and BS (Base Station). The full duplex RoF system is implemented by means of Wavelength Division Multiplexing (WDM) and Optical Add Drop Multiplexer (OADM), where WDM enables transmission of many signals via a single mode fiber for long distance while OADM allows data transmission of both down-link and uplink a by single-mode fiber (SMF). The modulation technique employed by the proposed system is DPSK. which has some advantages over binary PSK, like a low phase error rate and no need to know the absolute phase. The proposed RoF system has been simulated using Opti System 13.0 simulator. The system outcomes like the Q-factor, and BER with and without (DCF) at different fiber length have been used to discuss system performance. It has been observed that the proposed system improves the Q-factor by 6-units and the BER by 24 dB at CS and 57dB at BS respectively.

Traveling wave-like Fabry–Perot resonator-based add-drop filters

We have proposed and studied a novel channel add-drop filter (ADF) based on a single Fabry-Perot resonator. The resonator consists of two mode-conversion Bragg grating reflectors separated by a wide waveguide that laterally coupled to two narrow waveguides. It behaves like a traveling-wave resonator where fields are coupled to the buses in one direction. Compact and narrowband ADFs are achieved with dropping efficiencies higher than 95%, as shown by the three-dimensional finite-difference time-domain simulations. In addition, the proposed device is applied to realize an eight-channel add-drop multiplexer in the C-band by cascading the ADFs with adjusted channel wavelengths.

Athermal silicon optical add-drop multiplexers based on thermo-optic coefficient tuning of sol-gel material.

Silicon photonics has gained interest for its potential to provide higher efficiency, bandwidth and reduced power consumption compared to electrical interconnects in datacenters and high performance computing environments. However, it is well known that silicon photonic devices suffer from temperature fluctuations due to silicon's high thermo-optic coefficient and therefore, temperature control in many applications is required. Here we present an athermal optical add-drop multiplexer fabricated from ring resonators. We used a sol-gel inorganic-organic hybrid material as an alternative to previously used materials such as polymers and titanium dioxide. In this work we studied the thermal curing parameters of the sol-gel and their effect on thermal wavelength shift of the rings. With this method, we were able to demonstrate a thermal shift down to -6.8 pm/°C for transverse electric (TE) polarization in ring resonators with waveguide widths of 325 nm when the sol-gel was cured at 130°C for 10.5 hours. We also achieved thermal shifts below 1 pm/°C for transverse magnetic (TM) polarization in the C band under different curing conditions. Curing time compared to curing temperature shows to be the most important factor to control sol-gel's thermo-optic value in order to obtain an athermal device in a wide temperature range.

On-chip reconfigurable optical add-drop multiplexer for hybrid wavelength/mode-division-multiplexing systems.

A silicon-based on-chip reconfigurable optical add-drop multiplexer (ROADM) is presented for hybrid wavelength-division-multiplexing-mode-division-multiplexing systems. The present ROADM consists of a four-channel mode demultiplexer, four wavelength-selective thermo-optic switches based on microring resonators, and a four-channel mode multiplexer. With the present ROADM, one can add/drop one of wavelength channels of any mode to/from the multimode bus waveguide successfully with an excess loss of 2-5dB and an extinction ratio of ∼20 dB over a wavelength range of 1525-1555nm.

Monolithic Add–Drop Multiplexers in Fused Silica Fabricated by Femtosecond Laser Direct Writing

The fabrication of optical add-drop multiplexers in fused silica is demonstrated, for the first time to our knowledge, using the femtosecond laser direct writing technique. To achieve this, a Mach-Zehnder interferometer configuration was used for the signal routing by the implementation of 3-dB directional couplers, along with Bragg grating waveguides for wavelength selectivity. The fabrication of all individual devices required was optimized. The behavior of the fabricated add-drop multiplexer was characterized at around 1550 nm, where a 3-dB bandwidth of 0.19 ± 0.01 nm was obtained along with an intrachannel and adjacent interchannel crosstalk of -30 and -20 dB at Δλ = ± 0.75 nm, respectively. This study shows that such complex devices can be manufactured by femtosecond laser direct writing, with future improvements being discussed.

Real-Time ROADM Filtering Penalty Characterization and Generalized Precompensation for Flexible Grid Networks

Concatenated filtering is an important impairment in high-spectral density transmission systems enabled by flexible-grid reconfigurable optical add-drop multiplexers (ROADMs). In this paper, an analytical model for wavelength selective switches (WSS) modules is used to determine the statistical distribution of experimentally measured filter shapes and to obtain the cascaded filter characteristics. A generalized approach for filtering penalty assessment is proposed and verified using a commercial 200G 16-quadrature amplitude modulation (16QAM) transponder and WSS modules. A practical method for filter penalty reduction is described, whereby a single, optimized digital pre-equalization filter is used to compensate filtering effects of multiple concatenated WSSs. This pre-equalization of cascaded ROADM filters is demonstrated with a 100G quadrature phase shift keying (QPSK) C-form factor pluggable (CFP) transponder operating on the 37.5-GHz grid, resulting in a doubling of the number of WSSs, which can be supported per link from three to six.

A CMOS Compatible Ultracompact Silicon Photonic Optical Add-Drop Multiplexer with Misaligned Sidewall Bragg Gratings

We experimentally and via simulations demonstrate ultracompact single-stage and cascaded optical add-drop multiplexers using misaligned sidewall Bragg grating in a Mach–Zehnder interferometer for the silicon-on-insulator platform. The single-stage configuration has a device footprint of 400 ${\mu }\text{m}\,\times$ 90 ${\mu }\text{m}$ , and the cascaded configuration has a footprint of 400 ${\mu }\text{m}\,\times$ 125 ${\mu }\text{m}$ . The proposed designs have 3-dB bandwidths of 6 nm and extinction ratios of 25 dB and 51 dB, respectively, and have been fabricated for the transverse electric mode. A minimum lithographic feature size of 80 nm is used in our design, which is within the limitation of 193 nm deep ultraviolet lithography.

Software-Defined Silicon-Photonics-Based Metro Node for Spatial and Wavelength Superchannel Switching

Due to the growing popularity of optical superchannels and software-defined networking, reconfigurable optical add-drop multiplexer (ROADM) architectures for superchannel switching have recently attracted significant attention. ROADMs based on micro-electro-mechanical system (MEMS) and liquid crystal-on-silicon (LCoS) technologies are predominantly used. Motivated by requirements for low power, high-speed, small area footprint, and compact switching solutions, we propose and demonstrate spatial and wavelength flexible superchannel switching using monolithically integrated silicon photonics (SiP) micro-ring resonators (MRRs). We demonstrate the MRRs’ capabilities and potential to be used as a fundamental building block in ROADMs. Unicast and multicast switching operation of an entire superchannel is demonstrated after transmission over 50 km of standard single mode fiber. The performance of each sub-channel from the 120 Gb∕s QPSK Nyquist superchannel is analyzed, and degradation in error vector magnitude performance was observed for outer sub-channels due to the 3 dB bandwidth of the MRRs, which is comparable with the superchannel bandwidth. However, all sub-channels for all switching cases (unicast, multicast, and bi-directional operation) exhibit performance far below the 7%FEClimit. The switching time of the SiPMRRchip is such that high-capacity superchannel interconnects between users can be set up and reconfigured on the microsecond time scale.

Space division multiplexing optical communication using few-mode fibers

Abstract To realize ultra-high capacity long-haul transmission, space-division multiplexing (SDM) has emerged as a promising solution, in which each data channel is modulated into an individual spatial/polarization modes in few-mode fibers (FMF) to increase the overall number of parallel channels. In this paper, we review the latest advances in SDM technology on the FMF, component, digital signal processing (DSP), as well as transmission demonstrations. First, we introduce the FMF characteristics, fabrication and manufacturing issues including modal dispersion, mode coupling, and nonlinearities. We next discuss in detail several key SDM components such as spatial multiplexers/demultiplexers (MUX/DeMUX), optical amplifiers, mode converters and SDM reconfigurable optical add-drop multiplexer (ROADM). Accordingly, we explore the DSP algorithms for SDM systems, covering least mean squares (LMS), recursive least squares (RLS), hardware complexity analysis, and mode dependent effects. Besides, a number of recent experimental validations are evaluated enabling higher transmission capacity for short, medium and long distances.

Optical back propagation for fiber optic networks with hybrid EDFA Raman amplification.

We have investigated an optical back propagation (OBP) method to compensate for propagation impairments in fiber optic networks with lumped Erbium doped fiber amplifier (EDFA) and/or distributed Raman amplification. An OBP module consists of an optical phase conjugator (OPC), optical amplifiers and dispersion varying fibers (DVFs). We derived a semi-analytical expression that calculates the dispersion profile of DVF. The OBP module acts as a nonlinear filter that fully compensates for the nonlinear distortions due to signal propagation in a transmission fiber, and is applicable for fiber optic networks with reconfigurable optical add-drop multiplexers (ROADMs). We studied a wavelength division multiplexing (WDM) network with 3000 km transmission distance and 64-quadrature amplitude modulation (QAM) modulation. OBP brings 5.8 dB, 5.9 dB and 6.1 dB Q-factor gains over linear compensation for systems with full EDFA amplification, hybrid EDFA/Raman amplification, and full Raman amplification, respectively. In contrast, digital back propagation (DBP) or OPC-only systems provide only 0.8 ~ 1.5 dB Q-factor gains.

Application of Waveguide/Free-Space Optics Hybrid to ROADM Device

As optical networks have evolved from point-to-point systems to ring or mesh networks, the optical devices that are needed to construct optical nodes have become more important and need to be more scalable. Hybridization of waveguide and free-space optics, or spatial and planar optical circuits (SPOCs), may provide the solutions for such needs. An SPOC platform is attractive because it can take advantage of both waveguide technology and free-space optics. Waveguide technology provides a high degree of integration of optical functionality for devices such as splitters and non-wavelength selective switches while free-space optics supplies a high degree of parallelism with two-dimensional spatial light modulators such as a liquid crystal on silicon (LCOS) devices. In this paper, we summarize the basics of SPOC technology and review its application to reconfigurable optical add-drop multiplexing (ROADM) devices. The key elements of a waveguide on an SPOC platform are an arrayed-waveguide grating and a spatial beam transformer. The latter functions as a microlens array and provides attractive features such as dense integration of switches. An LCOS device has numerous phase modulating pixels, enabling flexible manipulation of lightwaves. Using an SPOC platform, we constructed and demonstrated devices for ROADM applications including a wavelength filter, tunable optical dispersion compensators, and wavelength selective switches (WSSs). The WSSs range from an ultrahigh port count WSS to a single module wavelength cross connect.

Reflection and Transmission Spectra of Multimode Interference Devices With Bragg Gratings

We numerically investigate the reflection and transmission spectra of multimode interference (MMI) devices incorporating uniform and sampled Bragg gratings with emphasis on their applications to an add-drop multiplexer (ADM). In numerical analysis, a rectangular index modulation is assumed as the grating and a 2×2 MMI device is treated to operate as a nearly two-mode interference (TMI) device, which is frequently used as an alternative to conventional directional couplers that have a disadvantage of large size. Although the first two guided modes are used in the TMI device, it is especially important to overlap their reflection bands. Therefore, a design method for attaining a sufficient overlap and some considerations are given. The spectral response of the TMI device with a uniform Bragg grating is analyzed by a combination of the mode-propagation method and the transfer-matrix method and discussed on the basis of the state of overlap. In the case of a sampled Bragg grating, it is found that although many modes are excited in the MMI section, multiple reflection bands (multi-channel) are created as expected. The treated device can be applied to single- and multi-channel ADMs.

Vertical integration of self-rolled-up microtube and silicon waveguides: a two-channel optical add–drop multiplexer

A novel design of a two-channel optical add–drop multiplexer based on a self-rolled-up microtube (SRM) is presented. This design consists of an SRM that has a parabolic lobe-like pattern along the tube’s axial direction, as well as straight silicon waveguides and a 180° waveguide bend. The vertical configuration of the SRM and waveguides is analyzed by the coupled mode theory for achieving the optimum gap. In the critical coupling regime, when the device serves as an optical demultiplexer, the minimum insertion loss is 1.94 dB, and the maximum channel crosstalk is −6.036 dB. Also, as an optical multiplexer, the maximum crosstalk becomes −11.9 dB.

基于空分复用的可重构光分插复用器

基于空分复用的可重构光分插复用器

Monolithically integrated reconfigurable add-drop multiplexer for mode-division-multiplexing systems.

An integrated reconfigurable optical add-drop multiplexer (ROADM) for mode-division-multiplexing systems is proposed and demonstrated for the first time, to the best of our knowledge. The present ROADM with four mode-channels is composed of a four-channel mode demultiplexer, four identical 2×2 thermo-optic Mach-Zehnder switches (MZSs), and a four-channel mode multiplexer, which are integrated monolithically on silicon. All the devices are designed for operation with TM polarization. The ROADM can add/drop any one of the mode channels freely by thermally turning on/off the corresponding MZS. For the added/dropped mode-channels, the excess loss is 1-5 dB, and the extinction ratio is 15-20 dB in the wavelength range of 1535-1565 nm.

Optical Switches Based on Silicon Photonics for ROADM Application

We demonstrate compact and low-loss 8 × 8 silicon photonic switch modules, which are applicable to transponder aggregators (TPAs) in colorless, directionless, and contentionless reconfigurable optical add-drop multiplexers. Newly designed silicon optical switch chips incorporating spot size converters with polarization insensitive and wavelength insensitive properties over C/L bands are packaged. The developed module shows about 6-dB average excess optical loss, including optical coupling loss, on all 64 optical paths with low-polarization-dependent loss and low crosstalk. Using these compact optical switch modules, we construct a TPA prototype featuring over 100-port optical switch subsystem densely mounted on one board and confirm its feasibility.

Stabilization and Frequency Control of a DFB Laser With a Tunable Optical Reflector Integrated in a Silicon Photonics PIC

We investigate the effect of tunable optical feedback on a commercial DFB laser edge coupled to a Silicon Photonics planar integrated circuit in which a tunable reflector has been implemented by means of a ring resonator based add-drop multiplexer. Controlled optical feedback allows for fine-tuning of the laser oscillation frequency. Under certain conditions it also allows suppression of bifurcation modes triggered by reflections occurring elsewhere on the chip. A semi-analytical model describing laser dynamics under combined optical feedback from the input facet of the edge coupler and from the tunable on-chip reflector fits the measurements. Compensation of detrimental effects from reflections induced elsewhere on a transceiver chip may allow moving isolators downstream in future communications systems, facilitating direct hybrid laser integration in Silicon Photonics chips, provided a suitable feedback signal for a control system can be identified. Moreover, the optical frequency tuning at lower feedback levels can be used to form a rapidly tunable optical oscillator as part of an optical phase locked loop, circumventing the problem of the thermal to free carrier effect crossover in the FM response of injection current controlled semiconductor laser diodes.