2D Array Research Articles

Tracking of a Magnetically Navigated Millirobot With a Magnetic-Field Camera

Significant progress has been made in the development of magnetic micromanipulation for minimally invasive surgery. The development of systems to localize millimeter-sized robots during magnetic manipulation without line-of-sight detection remains, however, a challenging task. In this study, we focused on the development of a tracking system aiming to fill this gap. A robot which consists of a cylindrical magnet of 1 mm diameter is localized using a 2D array of 3D magnetoresistive sensors. The system, also called magnetic field camera, provides tracking of the robot with a refresh rate of 2 Hz. The developed tracking algorithm reaches a mean absolute error for the position and the orientation of, respectively 0.56 mm and 5.13° in 2D. This system can be added to existing magnetic manipulation systems allowing closed loop control of the navigation. The performances of the magnetic field camera are not affected by an exposure to strong magnetic fields. Exposures up to 3 T have been validated. Increasing the integrability of the magnetic field camera into magnetic manipulation systems. The presented tracking system makes it possible to target applications such as minimally invasive eye surgery or drug delivery. The high spatial and magnetic resolutions allow the tracking of magnetic particles, down to 200 μm diameter, when placed close to the surface. The system could also be suitable for the localization of small objects for 2D biomanipulation.

Fly by Feel: Flow Event Detection via Bioinspired Wind-Hairs

Bio-inspired flexible pillar-like wind-hairs show promise for the future of flying by feel by detecting critical flow events on an aerofoil during flight. To be able to characterise specific flow disturbances from the response of such sensors, quantitative PIV measurements of such flow-disturbance patterns were compared with sensor outputs under controlled conditions. Experiments were performed in a flow channel with an aerofoil equipped with a 2D array of such sensors when in uniform inflow conditions compared to when a well-defined gust was introduced upstream and was passing by. The gust was generated through the sudden deployment of a row of flaps on the suction side of a symmetric wing that was placed upstream of the aerofoil with the sensors. The resulting flow disturbance generated a starting vortex with two legs, which resembled a horseshoe-type vortex shed into the wake. Under the same tunnel conditions, PIV measurements were taken downstream of the gust generator to characterise the starting vortex, while further measurements were taken with the sensing pillars on the aerofoil in the same location. The disturbance pattern was compared to the pillar response to demonstrate the potential of flow-sensing pillars. It was found that the pillars could detect the arrival time and structural pattern of the flow disturbance, showing the characteristics of the induced flow field of the starting vortex when passing by. Therefore, such sensor arrays can detect the “footprint” of disturbances as temporal and spatial signatures, allowing us to distinguish those from others or noise.

Compiling Quantum Circuits for Dynamically Field-Programmable Neutral Atoms Array Processors

Dynamically field-programmable qubit arrays (DPQA) have recently emerged as a promising platform for quantum information processing. In DPQA, atomic qubits are selectively loaded into arrays of optical traps that can be reconfigured during the computation itself. Leveraging qubit transport and parallel, entangling quantum operations, different pairs of qubits, even those initially far away, can be entangled at different stages of the quantum program execution. Such reconfigurability and non-local connectivity present new challenges for compilation, especially in the layout synthesis step which places and routes the qubits and schedules the gates. In this paper, we consider a DPQA architecture that contains multiple arrays and supports 2D array movements, representing cutting-edge experimental platforms. Within this architecture, we discretize the state space and formulate layout synthesis as a satisfiability modulo theories problem, which can be solved by existing solvers optimally in terms of circuit depth. For a set of benchmark circuits generated by random graphs with complex connectivities, our compiler OLSQ-DPQA reduces the number of two-qubit entangling gates on small problem instances by 1.7x compared to optimal compilation results on a fixed planar architecture. To further improve scalability and practicality of the method, we introduce a greedy heuristic inspired by the iterative peeling approach in classical integrated circuit routing. Using a hybrid approach that combined the greedy and optimal methods, we demonstrate that our DPQA-based compiled circuits feature reduced scaling overhead compared to a grid fixed architecture, resulting in 5.1X less two-qubit gates for 90 qubit quantum circuits. These methods enable programmable, complex quantum circuits with neutral atom quantum computers, as well as informing both future compilers and future hardware choices.

Transforming Undesired Corrosion Products into a Nanoflake-Array Functional Layer: A Gelatin-Assistant Modification Strategy for High Performance Zn Battery Anodes.

As corrosion products of Zn anodes in ZnSO4 electrolytes, Zn4SO4 (OH)6·xH2O with loose structure cannot suppress persistent side reactions but can increase the electrode polarization and induce dendrite growth, hindering the practical applications of Zn metal batteries. In this work, a functional layer is built on the Zn anode by a gelatin-assistant corrosion and low-temperature pyrolysis method. With the assistant of gelatin, undesired corrosion products are converted into a uniform nanoflake array comprising ZnO coated by gelatin-derived carbon on Zn foil (denoted Zn@ZnO@GC). It is revealed that the gelatin-derived carbons not only enhance the electron conductivity, facilitate Zn2+ desolvation, and boost transport/deposition kinetics, but also inhibit the occurrence of hydrogen evolution and corrosion reactions on the zincophilic Zn@ZnO@GC anode. Moreover, the 3D nanoflake array effectively homogenizes the current density and Zn2+ concentration, thus inhibiting the formation of dendrites. The symmetric cells using the Zn@ZnO@GC anodes exhibit superior cycling performance (over 7000h at 1mA cm-2/1 mAh cm-2) and without short-circuiting even up to 25 mAh cm-2. The Zn@ZnO@GC||NaV3O8 full cell works stably for 5000 cycles even with a limited N/P ratio of ≈5.5, showing good application prospects.

Nanotopology-Enabled On-Site Pathogen Detection for Managing Atopic Dermatitis.

Atopic dermatitis (AD), a prevalent skin condition often complicated by microbial infection, poses a significant challenge in identifying the responsible pathogen for its effective management. However, a reliable, safe tool for pinpointing the source of these infections remains elusive. In this study, a novel on-site pathogen detection that combines chemically functionalized nanotopology with genetic analysis is proposed to capture and analyze pathogens closely associated with severe atopic dermatitis. The chemically functionalized nanotopology features a 3D hierarchical nanopillar array (HNA) with a functional polymer coating, tailored to isolate target pathogens from infected skin. This innovative nanotopology demonstrates superior pathogenic capture efficiency, favorable entrapment patterns, and non-cytotoxicity. An HNA-assembled stick is utilized to directly retrieve bacteria from infected skin samples, followed by extraction-free quantitative loop-mediated isothermal amplification (direct qLAMP) for validation. To mimic human skin conditions, porcine skin is employed to successfully capture Staphylococcus aureus, a common bacterium exacerbating AD cases. The on-site detection method exhibits an impressive detection limit of 103 cells mL-1. The HNA-assembled stick represents a promising tool for on-site detection of bacteria associated with atopic dermatitis. This innovative approach enables to deepen the understanding of AD pathogenesis and open avenues for more effective management strategies for chronic skin conditions.

Persymmetric design of jointly detection and bearing estimation for a 2D array radar in training demanding scenarios

The problem of joint detection and bearing estimation for a two-dimensional (2D) array radar in training demanding scenarios is addressed. Regardless of the cause of the angle deviation, we model the 2D steering vector as a fully incremental form. Thus, the 2D array requires the optimization of two target cosine offsets. To relax the requirement of sufficient training data, we incorporate persymmetric structure in the design of the receiver. Unlike traditional joint optimization, the persymmetric structure brings a more complex multidimensional matrix form, making detection optimization more difficult. Then, we transform the optimization problem into a fractional-order programming problem and solve it by Dinkelbach algorithm. Finally, numerical results verify the superiority of the proposed method over conventional methods in insufficient training scenarios. Also, the proposed method is more robust.

Gaussian to flat-top beam shaping in an off-axis reflective scenario by a millimeter-wave metasurface.

In this paper, we present a metallic reflectarray for shaping the emitted Gaussian beam of a 100GHz horn antenna in reflective and off-axis mode. The proposed reflectarray is a compact planar surface consisting of a 2D array of unit cells with a thin Rogers 5880 substrate. This reflectarray offers advantages over other beam shapers in millimeter-wave (MMW) imaging, as it generates a flat-top beam in off-axis reflective mode and is straightforward to fabricate. To conduct a feasibility study, we first introduce the 1D reflectarray. The phase profile of the 1D reflectarray is a linear combination of a beam shaping phase profile based on geometrical optics (GO) and a compensating phase profile. The design of the 1D reflectarray involves tailoring the dimensions of the unit cells in one direction. We calculate the scattered field from the 1D reflectarray using the finite element method (FEM) and then determine the generated beam using the Fresnel diffraction integral. Subsequently, we design the 2D reflectarray following the same approach by using a 2D version of the proposed phase profile. The full-wave simulation is employed to calculate the generated beam at a certain distance from the reflectarray. The results reveal the successful generation of a high-quality flat-top beam, showcasing the proposed reflectarray as an evolutionary solution among beam shapers.

Increasing abdominal aortic aneurysm curvature visibility using 3D dual probe bistatic ultrasound imaging combined with probe translation

High frame rate ultrasound (US) imaging techniques in 3D are promising tools for capturing abdominal aortic aneurysms (AAAs) over time, however, with the limited number of channel-to-element connections current footprints are small, which limits the field of view. Moreover, the maximal steering angle of the ultrasound beams in transmit and the maximal receptance angle in receive are insufficient for capturing the curvy shape of the AAA. Therefore, an approach is needed towards large arrays. In this study, high frame rate bistatic 3D US data (17 Hz) were acquired with two synchronized matrix arrays positioned at different locations (multi-aperture imaging) using a translation stage to simulate what a larger array with limited channel-to-element connections can potentially achieve. Acquisitions were performed along an AAA shaped phantom with different probe tilting angles (0 up to ± 30°). The performance of different multi-aperture configurations was quantified using the generalized contrast-to-noise ratio of the wall and lumen (gCNR). Furthermore, a parametric model of the multi-aperture system was used to estimate in which AAA wall regions the contrast is expected to be high. This was evaluated for AAAs with increasing diameters and curvature. With an eight-aperture 0° probe angle configuration a 69 % increase in field of view was measured in the longitudinal direction compared to the field of view of a single aperture configuration. When increasing the number of apertures from two to eight, the gCNR improved for the upper wall and lower wall by 35 % and 13 % (monostatic) and by 36 % and 13 % (bistatic). Contrast improvements up to 22 % (upper wall) and 12 % (lower wall) are achieved with tilted probe configurations compared to non-tilted configurations. Moreover, with bistatic imaging with tilted probe configurations gCNR improvements up to 4 % (upper wall) and 7 % (lower wall) are achieved compared to monostatic imaging. Furthermore, imaging with a larger inter-probe distance improved the gCNR for a ± 15° probe angle configuration. The gCNR has an expected pattern over time, where the contrast is lower when there is more wall motion (systole) and higher when motion is reduced (diastole). Furthermore, a higher frame rate (45 Hz) yields a lower gCNR, because fewer compound angles are used. The results of the parametric model suggest that a flat array is suitable for imaging AAA shapes with limited curvature, but that it is not suitable for imaging larger AAA shapes with more curvature. According to the model, tilted multi-aperture configurations combined with bistatic imaging can achieve a larger region with high contrast compared to non-tilted configurations. The findings of the model are in agreement with experimental findings. To conclude, this study demonstrates the vast improvements in field of view and AAA wall visibility that a large, sparsely populated 3D array can potentially achieve when imaging AAAs compared to single or dual aperture imaging. In the future, larger arrays, less thermal noise, more steering, and more channel-to-element connections combined with carefully chosen orientations of (sub-) apertures will likely advance 3D imaging of AAAs.

Real-time 3D ultrasound imaging with a clip-on device attached to common 1D array transducers

Performing 3D ultrasound imaging at a real-time volume rate (e.g., >20 Hz) is a challenging task. While 2D array transducers remain the most practical approach for real-time 3D imaging, the large number of transducer elements (e.g., several thousand) that are necessary to cover an effective 3D field-of-view impose a fundamental constraint on imaging speed. Although solutions such as multiplexing and specialized transducers, including sparse arrays and row-column-addressing arrays, have been developed to address this limitation, they inevitably compromise imaging quality (e.g., SNR, resolution) in favor of speed. Coupled with the high equipment cost of 2D arrays, these compromises hinder the widespread adoption of 3D ultrasound imaging technologies in clinical settings. In this presentation, we introduce an innovative transducer clip-on device comprising a water-immersible, fast-tilting electromechanical acoustic reflector and a redirecting reflector to enable real-time 3D ultrasound imaging using common 1D array transducers. We will first introduce the principles underlying our novel technique, followed by validation studies incorporating simulation and experimental data. We will also demonstrate the feasibility of using the clip-on device to achieve a high 3D imaging volume rate that is suitable for advanced imaging modes such as shear wave elastography, blood flow imaging, and super-resolution ultrasound localization microscopy.

Ultrasonic flexible array for non-destructive testing of complex curved surfaces

Ultrasound detection technology in Non-Destructive Testing (NDT) is widely used. Ultrasonic transducer arrays effectively solved the problem of limitation in the detection range of single beam scanning transducers. However, the common used ultrasonic transducer arrays are rigid that are difficult to achieve complete contact with complex curved surfaces. Flexible arrays can be bent to a certain extent and can adaptively fit the surface of different curvature structures for detection. This work reported ultrasonic transducer flexible arrays that combine 2D arrays and linear arrays. The arrays have eight lines and each can be individually controlled. Each line has eight elements. The arrays expand the detection range and greatly reduce the control circuit difficulty and signal processing difficulty. The average operating frequency of the measured arrays is 2.5 MHz, the bandwidth is close to 30% and the insertion loss is close to −33 dB. Also, the arrays can detect defects through curved surface testing. Based on these advantages, this study paved the way for further investigation into the flexible ultrasonic arrays.

Transmit beam design for tissue harmonic volume imaging of muscular tissues with a row-column array

Row-Column-addressed Arrays (RCAs), which have recently become commercially available, transmit along the rows and receive along columns of a 2D array in order to produce 3D volume images with low channel count. Imaging of the inherently three-dimensional, layered, and fibrous structure of muscular tissues in 3D using an RCA can improve evaluations of muscle function and disease compared to conventional 2D cross-sectional imaging, but volume images obtained using an RCA suffer from low lateral spatial resolution, low contrast, and grating lobe artifacts. Tissue harmonic imaging (THI) employs nonlinear acoustic effects to image at twice the transmit frequency, and can yield increased spatial resolution, increased contrast, and decreased artifacts from grating lobes. Here we investigate transmission considerations for THI in muscular tissues using a commercially available RCA (Vermon RC6gV). The parameter space is explored efficiently with frequency domain simulations of the 3D Westervelt equation. Pulse inversion imaging is applied experimentally using both steered plane wave and focused transmits to evaluate THI with an RCA in tissue phantoms and in muscular tissue. Pulse inversion volume images are compared to conventional images in terms of signal-to-noise, contrast, and ability to identify layers and fibrous structures in muscle in 3D. [Work supported by NIH HEAL Initiative R61AT012282.]

Linear and Nonlinear Behaviors of the Photoreceptor Coupled Network.

Photoreceptors are electrically coupled to one another, and the spatiotemporal properties of electrical synapses in a two-dimensional retinal network are still not well studied, because of the limitation of the single electrode or pair recording techniques which do not allow simultaneously measuring responses of multiple photoreceptors at various locations in the retina. A multiple electrode recording system is needed. In this study, we investigate the network properties of the two-dimensional rod coupled array of the salamander retina (both sexes were used) by using the newly available multiple patch electrode system that allows simultaneous recordings from up to eight cells and to determine the electrical connectivity among multiple rods. We found direct evidence that voltage signal spread in the rod-rod coupling network in the absence of I h (mediated by HCN channels) is passive and follows the linear cable equation. Under physiological conditions, I h shapes the network signal by progressively shortening the response time-to-peak of distant rods, compensating the time loss of signal traveling from distant rods to bipolar cell somas and facilitating synchronization of rod output signals. Under voltage-clamp conditions, current flow within the coupled rods follows Ohm's law, supporting the idea that nonlinear behaviors of the rod network are dependent on membrane voltage. Rod-rod coupling is largely symmetrical in the 2D array, and voltage-clamp blocking the next neighboring rod largely suppresses rod signal spread into the second neighboring rod, suggesting that indirect coupling pathways play a minor role in rod-rod coupling.

Tuning and total resonant suppression of reflection in the photonic bandgap range of Bragg reflector by two-dimensional nanoparticle array

The influence of a dielectric layer with an embedded 2D array of metal nanoparticles on the spectral characteristics of a distributed Bragg reflector is theoretically studied and numerically validated. A significant dependence of the reflectivity of the hybrid structure on the location of the nanoparticle array relative to the maxima and minima of the optical field in the surface dielectric layer is demonstrated. It is found that the application of a dilute ensemble of nanoparticles (the interparticle distance is from 2 to 5 times larger than the nanoparticle size) in the region of high optical field localization makes it possible to obtain a total suppression of reflection in the photonic bandgap range of distributed Bragg reflector. Contrariwise, if the optical field is almost zero at the nanoparticle array location, its impact on the scattered light is negligible, that is, the resonant nanoparticles are masked by a highly reflective photonic structure. The target wavelength can be tuned inside the photonic bandgap range by adjusting the shape of nanoparticles and interparticle distance in the array.

High-frequency surface-micromachined optical ultrasound transducer array for 3D micro photoacoustic computed tomography.

This Letter reports a new, to the best of our knowledge, high-frequency surface-micromachined optical ultrasound transducer (HF-SMOUT) array for micro photoacoustic computed tomography (µPACT). An 11 × 11 mm2 2D array of 220 × 220 elements (35 µm in diameter) is designed, fabricated, and characterized. The optical resonance wavelength (ORW) of ≥90% of the elements falls within a 6-nm range. The acoustic center frequency and bandwidth of the elements are ∼14 MHz and ∼18 MHz (129%), respectively. The noise equivalent pressure (NEP) is 161 Pa (or 18 m P a/H z) within a measurement bandwidth of 5-75 MHz. The standard deviation of the ORW drift is 0.45 nm and 0.93 nm within 25°C-55°C, respectively, and during a seven-day continuous water immersion. PACT experiments are conducted to evaluate the imaging performances of the HF-SMOUT array. The spatial resolution is estimated as 90 µm (axial) and 250-750 µm (lateral) within a 10 × 10 mm2 field of view (FoV) and the imaging depth of 16 mm. A 3D PA image of a knotted black hair target is also successfully acquired. These results demonstrate the feasibility of using the HF-SMOUT array for µPACT applications.

Interface‐Confined Assembly of Layered Molecular Crystal Arrays Toward Wearable UV‐Radiation Monitor

AbstractOrganic semiconductors have significant potential for wearable optoelectronics due to their designable molecular structures, tunable photoelectronic properties, and flexibility. For their integration into optoelectronic devices, organic semiconductors need to be assembled into single‐crystalline arrays with both precise alignment of micro‐/nanostructures and long‐range order of molecules. In this study, an interface‐confined lithography technique is developed for fabricating organic single‐crystalline microwire arrays with layered molecular stacking and ordered crystallographic orientation toward wearable UV radiation monitor. This interface‐confined strategy introduces parallel gas–liquid–solid three‐phase contact line (TPCL) arrays to suppress the lateral growth of single crystals. Meanwhile, TPCLs with controlled dewetting direction promote longitudinal growth, thus universally yielding 1D arrays based on various organic semiconducting small molecules. These 1D single‐crystalline arrays exhibit high average mobility of 12.5 cm2 V−1 s−1 with uniform electronic properties of 9.3% variation, and good mechanical stability after 1000 bending times. Based on organic 1D arrays, wearable devices with robust photoresponsivity of 8.26 × 103 A W−1 and high mechanical flexibility achieve real‐time monitoring of UV radiation to prevent skin disease. This confined‐assembly strategy opens a new avenue to construct wearable optoelectronic devices for health monitoring.

High-Performance Gel-Free and Label-Free Size Fractionation of Extracellular Vesicles with Two-Dimensional Electrophoresis in a Microfluidic Artificial Sieve.

Extracellular vesicles (EVs) are cell-derived particles that exhibit diverse sizes, molecular contents, and clinical implications for various diseases depending on their specific subpopulations. However, fractionation of EV subpopulations with high resolution, efficiency, purity, and yield remains an elusive goal due to their diminutive sizes. In this study, we introduce a novel strategy that effectively separates EV subpopulations in a gel-free and label-free manner, using two-dimensional (2D) electrophoresis in a microfluidic artificial sieve. The microfabricated artificial sieve consists of periodically arranged micro-slit-well structures in a 2D array and generates an anisotropic electric field pattern to size fractionate EVs into discrete streams and steer the subpopulations into designated outlets for collection within a minute. Along with fractionating EV subpopulations, contaminants such as free proteins and short nucleic acids can be simultaneously directed to waste outlets, thus accomplishing both size fractionation and purification of EVs with high performance. Our platform offers a simple, rapid, and versatile solution for EV subpopulation isolation, which can potentially facilitate the discovery of biomarkers for specific EV subtypes and the development of EV-based therapeutics.

Visible Meta-Displays for Anti-Counterfeiting with Printable Dielectric Metasurfaces.

Metasurfaces, 2D arrays of nanostructures, have gained significant attention in recent years due to their ability to manipulate light at the subwavelength scale. Their diverse applications range from advanced optical devices to sensing and imaging technologies. However, the mass production of dielectric metasurfaces with tailored properties for visible light has remained a challenge. Therefore, the demand for efficient and cost-effective fabrication methods for metasurfaces has driven the continuing development of various techniques. In this research article, a high-throughput production method is presented for multifunctional dielectric metasurfaces in the visible light range using one-step high-index TiO2-polymer composite (TPC) printing, which is a variant of nanoprinting lithography (NIL) for the direct replication of patterned multifunctional dielectric metasurfaces using a TPC material as the printing ink. The batch fabrication of dielectric metasurfaces is demonstrated with controlled geometry and excellent optical response, enabling high-performance light-matter interactions for potential applications of visiblemeta-displays.

High‐Performance Organic Phototransistors Based on Single‐Crystalline Microwire Arrays

AbstractHigh‐performance organic phototransistors (OPTs) have attracted considerable attention owing to their high photoresponse and low‐cost solution‐processing manufacturing. To meet the increasing demand for integrated optoelectronic circuits, organic single‐crystalline micro‐/nanowire arrays for OPTs construction are prominently anticipated. However, the manufacturing and patterning of organic single‐crystalline arrays have hit a bottleneck due to the uncontrollable dewetting dynamics. In this work, a capillary‐bridge lithography strategy is proposed to guide ordered nucleation and unidirectional dewetting of microfluid, thus enabling the large‐scale preparation of highly aligned organic single‐crystalline microwire arrays. Taking advantage of efficient carrier transport, a competitive average field‐effect hole mobility (μ) of 6.64 cm2 V−1 s−1 is obtained, and the high‐throughput one‐dimensional (1D) arrays based OPTs also exhibit excellent optoelectrical performance with photosensitivity (P) of 1.36 × 106, responsivity (R) of 3.18 × 104 A W−1, and specific detectivity (D*) of 9.22 × 1014 Jones. This work provides a guide for the designing and patterning of high‐throughput OPTs toward multifunctional integrated optoelectronics.

Quantitative Analysis of Resistance to Deformation of the DNA Origami Framework Supported by Struts.

Nanostructures with controlled shapes are of particular interest due to their consistent physical and chemical properties and their potential for assembly into complex superstructures. The use of supporting struts has proven to be effective in the construction of precise DNA polyhedra. However, the influence of struts on the structure of DNA origami frameworks on the nanoscale remains unclear. In this study, we developed a flexible square DNA origami (SDO) framework and enhanced its structural stability by incorporating interarm supporting struts (SDO-s). Comparing the framework with and without such struts, we found that SDO-s demonstrated a significantly improved resistance to deformation. We assessed the deformability of these two DNA origami structures through the statistical analysis of interior angles of polygons based on atomic force microscopy and transmission electron microscopy data. Our results showed that SDO-s exhibited more centralized interior angle distributions compared to SDO, reducing from 30-150° to 60-120°. Furthermore, molecular dynamics simulations indicated that supporting struts significantly decreased the thermodynamic fluctuations of the SDO-s, as described by the root-mean-square fluctuation parameter. Finally, we experimentally demonstrated that the 2D arrays assembled from SDO-s exhibited significantly higher quality than those assembled from SDO. These quantitative analyses provide an understanding of how supporting struts can enhance the structural integrity of DNA origami frameworks.

Broad Elevation Projection Super-Resolution Ultrasound (BEP-SRUS) Imaging With a 1-D Unfocused Linear Array.

Super-resolution ultrasound (SRUS) through localizing spatially isolated microbubbles (MBs) has been demonstrated to overcome the wave diffraction limit and reveal the microvascular structure and flow information at the microscopic scale. However, 3-D SRUS imaging remains a challenge due to the fabrication and computational complexity of 2-D matrix array probes. Inspired by X-ray radiography which can present information within a volume in a single projection image with much simpler hardware than X-ray computerized tomography (CT), this study investigates the feasibility of broad elevation projection super-resolution (BEP-SR) ultrasound using a 1-D unfocused linear array. Both simulation and in vitro experiments were conducted on 3-D microvessel phantoms. In vivo demonstration was done on the Rabbit kidney. Data from a 1-D linear array with and without an elevational focus were synthesized by summing up row signals acquired from a 2-D matrix array with and without delays. A full 3-D reconstruction was also generated as the reference, using the same data of the 2-D matrix array but without summing row signals. Results show that using an unfocused 1-D array probe, BEP-SR can capture significantly more information within a volume in both vascular structure and flow velocity than the conventional 1-D elevational-focused probe. Compared with the 2-D projection image of the full 3-D SRUS results using the 2-D array probe with the same aperture size, the 2-D projection SRUS image of BEP-SR has similar volume coverage, using 32 folds fewer independent elements. This study demonstrates BEP-SR's ability of high-resolution imaging of microvascular structures and flow velocity within a 3-D volume at significantly reduced costs. The proposed BEP method could significantly benefit the clinical translation of the SRUS imaging technique by making it more affordable and repeatable.