X-ray Absorption Fine Structure Research Articles

Quantitative Insights into Phosphate-Enhanced Lead Immobilization on Goethite.

Despite extensive study, geochemical modeling often fails to accurately predict lead (Pb) immobilization in environmental samples. This study employs the Charge Distribution MUlti-SIte Complexation (CD-MUSIC) model, X-ray absorption fine structure (XAFS), and density functional theory (DFT) to investigate mechanisms of phosphate (PO4) induced Pb immobilization on metal (hydr)oxides. The results reveal that PO4 mainly enhances bidentate-adsorbed Pb on goethite via electrostatic synergy at low PO4 concentrations. At relatively low pH (below 5.5) and elevated PO4 concentrations, the formation of the monodentate-O-sharing Pb-PO4 ternary structure on goethite becomes important. Precipitation of hydropyromorphite (Pb5(PO4)3OH) occurs at high pH and high concentrations of Pb and PO4, with an optimized log Ksp value of -82.02. The adjustment of log Ksp compared to that in the bulk solution allows for quantification of the overall Pb-PO4 precipitation enhanced by goethite. The CD-MUSIC model parameters for both the bidentate Pb complex and the monodentate-O-sharing Pb-PO4 ternary complex were optimized. The modeling results and parameters are further validated and specified with XAFS analysis and DFT calculations. This study provides quantitative molecular-level insights into the contributions of electrostatic enhancement, ternary complexation, and precipitation to phosphate-induced Pb immobilization on oxides, which will be helpful in resolving controversies regarding Pb distribution in environmental samples.

Investigating Anharmonic XAFS Debye-Waller Factor of Crystalline Tungsten Based on Einstein Model

The anharmonic X-ray absorption fine structure (XAFS) Debye-Waller (DW) factor of the crystalline tungsten (W) has been investigated in the temperature-dependent. This DW factor is calculated in explicit forms using the quantum anharmonic correlated Einstein model developed from the correlated Einstein model based on the anharmonic effective potential and the quantum statistical theory. The numerical results of W in the temperature range from 0 to 900 K are in good agreement with those obtained by the other theoretical models and experiments at several temperatures. The analytical results show that the anharmonic correlated Einstein model is suitable for analyzing the experimental XAFS data of metals.

Structure of Polaronic Centers in Proton-Intercalated AWO4 Scheelite-Type Tungstates.

The studies of polaronic centers in a homologous series of scheelite-type compounds AWO4 (A = Ca, Sr, Ba) were performed using the W L3-edge and Sr K-edge X-ray absorption spectroscopy combined with the reverse Monte Carlo simulations, X-ray photoelectron spectroscopy (XPS), and first-principles calculations. Protonated scheelites HxAWO4 were produced using acid electrolytes in a one-step route at ambient conditions. The underlying mechanism behind this phenomenon can be ascribed to the intercalation of H+ into the crystal structure of tungstate, effectively resulting in the reduction of W6+ to W5+, i.e., the formation of polaronic centers, and giving rise to a characteristic dark blue-purple color. The emergence of the W5+ was confirmed by XPS experiments. The relaxation of the local atomic structure around the W5+ polaronic center was determined from the analysis of the extended X-ray absorption fine structures using the reverse Monte Carlo method. The results obtained suggest the displacement of the W5+ ions from the center of [W5+O4] tetrahedra in the structure of AWO4 scheelite-type tungstates. This finding was also supported by the results of the first-principles calculations.

Low-Temperature Methane Activation Reaction Pathways over Mechanochemically-Generated Ce4+/Cu+ Interfacial Sites.

Methane is a valuable resource and its valorization is an important challenge in heterogeneous catalysis. Here it is shown that CeO2/CuO composite prepared by ball milling activates methane at a temperature as low as 250°C. In contrast to conventionally prepared catalysts, the formation of partial oxidation products such as methanol and formaldehyde is also observed. Through an in situ Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) and operando Near Edge X-Ray Absorption Fine Structure Spectroscopy (NEXAFS) approach, it can be established that this unusual reactivity can be attributed to the presence of Ce4+/Cu+ interfaces generated through a redox exchange between Ce3+ and Cu2+ atoms facilitated by the mechanical energy supplied during milling. DFT modeling of the electronic properties confirms the existence of a charge transfer mechanism. These results demonstrate the effectiveness and distinctiveness of the mechanical approach in creating unique and resilient interfaces thereby enabling the optimization and refining of CeO2/CuO catalysts in methane activation reactions.

Subnanometer‐sized CuOx Clusters on TiO2 as Active Photocatalysts for Ammonia Production from Photocatalytic Nitration Reduction Reaction

AbstractThe Haber‐Bosch process is commonly used to produce ammonia while consuming energy and yielding huge emissions of carbon dioxide. Finding an alternative way to produce ammonia sustainably is a promising research direction with less CO2 emission. Photochemical nitrate reduction reaction (NtRR) to ammonia (NH3) could solve the nitrate pollutant problem in water and approach to produce ammonia with a more environmentally friendly process and lower energy consumption. In this work, the subnanometer‐sized copper oxide clusters decorated on titanium oxide nanoparticles (CuOx‐TiO2) were synthesized through the hydrothermal method and calcination treatment. CuOx‐TiO2 demonstrated impressively conversion rate of NO3− to NH3 with a yield of 153.09 μg‐gcat−1‐h−1 in KNO3 solution. The characteristic structure analysis revealed CuOx clusters with ~less than 1 nm decorated on TiO2 nanoparticles. From in‐situ X‐ray absorption fine structure (XAFS) spectroscopic technique, the transformation of the oxidation state of Cu clusters and the changes of local structure in the CuOx‐TiO2 were observed. The photocatalytic reaction mechanism of nitrate reduction on the CuOx‐TiO2 was successfully revealed. These discoveries have broad implications for the functional advancement of catalysts based on subnanometer‐sized clusters. Our findings may pave the way for exploring advanced ammonia synthesis routes with reduced energy consumption and carbon emissions.

Local Charge Transfer Unveils Antideactivation of Ru at High Potentials for the Alkaline Hydrogen Oxidation Reaction.

The activity of Ru-based alkaline hydrogen oxidation reaction (HOR) electrocatalysts usually decreases rapidly at potentials higher than 0.1 V (vs a reversible hydrogen electrode (RHE)), which significantly limits the lifetime of fuel cells. It is found that this phenomenon is caused by the overadsorption of the O species due to the overcharging of Ru nanoparticles at high potentials. Here, Mn1Ox(OH)y clusters-modified Ru nanoparticles (Mn1Ox(OH)y@Ru/C) were prepared to promote charge transfer from overcharged Ru nanoparticles to Mn1Ox(OH)y clusters. Mn1Ox(OH)y@Ru/C exhibits high HOR activity and stability over a wide potential range of 0-1.0 V. Moreover, a hydroxide exchange membrane fuel cell with a Mn1Ox(OH)y@Ru/C anode delivers a high peak power density of 1.731 W cm-2, much superior to that of a Pt/C anode. In situ X-ray absorption fine structure (XAFS) analysis and density functional theory (DFT) calculations reveal that Mn in Mn1Ox(OH)y clusters could receive more electrons from overcharged Ru at higher potentials and significantly decrease the overadsorption of the O species on Ru, thus permitting the HOR on Ru to proceed at high potentials. This study provides guidance for the design of alkaline HOR catalysts without activity decay at high potentials.

Copper-Based Complexes with Adamantane Ring-Conjugated bis(3,5-Dimethyl-pyrazol-1-yl)acetate Ligand as Promising Agents for the Treatment of Glioblastoma.

The new ligand L2Ad, obtained by conjugating the bifunctional species bis(3,5-dimethylpyrazol-1-yl)-acetate and the drug amantadine, was used as a chelator for the synthesis of new Cu complexes 1-5. Their structures were investigated by synchrotron radiation-induced X-ray photoelectron spectroscopy (SR-XPS), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, and by combining X-ray absorption fine structure (XAFS) spectroscopy techniques and DFT modeling. The structure of complex 3 was determined by single-crystal X-ray diffraction analysis. Tested on U87, T98, and U251 glioma cells, Cu(II) complex 3 and Cu(I) complex 5 decreased cell viability with IC50 values significantly lower than cisplatin, affecting cell growth, proliferation, and death. Their effects were prevented by treatment with the Cu chelator tetrathiomolybdate, suggesting the involvement of copper in their cytotoxic activity. Both complexes were able to increase ROS production, leading to DNA damage and death. Interestingly, nontoxic doses of 3 or 5 enhanced the chemosensitivity to Temozolomide.

Single−atom Co anchored on covalent organic framework for remarkable photocatalytic hydrogen evolution efficiency

Single-atom catalysts (SACs) have attracted extensive attention because of their high atomic utilization and superior catalytic activity. Herein, single-atom Co has anchored on the β-ketoenamine-linked covalent organic framework (Tp-Tta COF) pores and used for remarkable photocatalytic hydrogen(H2) production under Ultraviolet–Visible light (UV–Vis light) irradiation. The single-atom Co is visualized by the aberration-corrected high-angle annular dark-field scanning transmission electron microscopy (AC HAADF-STEM), and the C3–Co–N1 coordination structure is demonstrated by X-ray absorption fine structure (XAFS) measurements. The modified Co0.4-SAC/Tp-Tta COF shows a high photocatalytic H2 production of 1798.5 μmol g−1 h−1 and the Apparent quantum yield(AQY) is 3.02% at 420 nm. The improvement of the activity and stability of the photocatalyst is mainly attributed to the incorporation of Co single-atom that boosts the separation efficiency of photogenerated electron-hole pair and provides well-dispersed active sites. This study provides valuable insights into the development of UV–Vis light-responsive photocatalysts at the atomic level.

Immobilization of Cu(II) and Zn(II) into hydrocalumite - An X-ray absorption fine structure (XAFS) investigation

The fate of heavy metals is crucial to the reuse of municipal waste incineration ash (MWIA) as construction materials. It is, however, not completely clear how they interact with cementitious phases at the molecular scale. This study investigated the uptake and speciation of Cu(II) and Zn(II) during the generation of Al-hydrocalumite-type high-pH phases through co-precipitation and adsorption experiments. Hydrocalumite (Hc) and minor phases, such as calcite and hydrogarnet, were identified as primary phases using X-ray diffraction (XRD). The characterization of Hc+Cu(II), Hc+Zn(II), and Hc+Cu(II)+Zn(II) via XRD, SEM, and bulk Cu(II)/Zn(II) EXAFS showed that both Cu(II) and Zn(II) exists as the surface/interlayer adsorption on the Hc+Cu(II)/Hc+Zn(II) and Hc+Cu(II)+Zn(II). Thermodynamic calculations support the experimental observations for the bulk phase. This study help understand the interacting mechanism between Cu(II)/Zn(II) and Hc phase, and pave the way of safe utilization of heavy-metal-containing waste as supplementary cementitious materials.

Manganese Oxides with Different Morphologies In Situ Anchored onto Ti3C2Tx Nanosheets: Highly Effective Decontamination toward Sulfur Mustard Simulants.

Manganese oxides with porous structure and abundant active sites show potential in degrading sulfur mustard (HD). However, there is an interface effect between the oily liquid HD and nano oxides, and the powder is prone to agglomeration, which leads to incomplete contact and limited degradation ability. Here, we demonstrate a simple hydrothermal method for preparing MnO2/Ti3C2 composites to address this problem. The influence of morphology and crystal structure on performance are examined. Herein, flower-like MnO2 is loaded onto the surface or interlayer of Ti3C2-MXene nanosheets during in situ formation, significantly expanding the specific surface area. It also provides abundant acid-base sites and oxygen vacancies for the degradation of simulants 2-chloro-ethyl-ethyl thioether (2-CEES) without external energy, resulting in a reaction half-life as fast as 12.5 min. The relationship between structure and performance is clearly elaborated through temperature-programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), and X-ray absorption fine structure (XAFS) analyses. Based on in situ attenuated total reflection-Fourier transform infrared (ATR-FTIR) analysis, gas chromatography-mass spectrometry (GC-MS) analysis, and density functional theory (DFT) calculation, the proposed degradation pathway of the 2-CEES molecule is a synergistic effect of hydrolysis, elimination, and oxidation. Furthermore, the products are nontoxic or low toxic. Metal oxide/MXene composites are first illustrated for their potential use in degrading sulfur mustard, suggesting new insights into these materials as novel decontamination for decomposing chemical warfare agents.

Nanoscale assembly of MoS2/CoS2/Ni3S2 grown on Ni foam for synergistic capture of iodine

We report a series of MoS2/CoS2/Ni3S2/NF heterogeneous interfaces with multiple types of adsorption sites, which exhibit excellent iodine capture performance. The optimized MoS2/CoS2/Ni3S2/NF-13 obtained at Mo:Co molar ratio of 1:3 shows an extremely large maximum iodine capture of 1804 mg/g. For the including component of Ni3S2/NF, REDOX reaction between Ni0/S2- and I2 offers the main driving force of chemisorption toward iodine (forming NiI2 and S8), while for MoS2, the electrostatic adsorption makes the main contribution to the iodine capture, and for CoS2, interfacial interactions promote the uptake capability of iodine. We perform density functional theory (DFT) calculations to determine the iodine adsorption energies (Ead), which show that in Ni3S2 the Ni and S both serve as iodine sorption sites and Ni site binds more tightly to I2 than S site does, while for MoS2, the S site (rather than Mo) prefers to adsorb the I2. X-ray absorption fine structures (XAFS) indicate that after iodine capture, oxidation states of Mo and Ni are increased more than that of Co, verifying Ni3S2 and MoS2 interact more than CoS2 on I2. Though CoS2 component does not directly adsorb I2, interfacial electron transfers of Co → Ni and Co → Mo significantly promote iodine sorption capability. Synergistic effect of the multiple components/sites in the MoS2/CoS2/Ni3S2/NF assembly offers the wonderful iodine capture. This work provides a novel perspective and theoretical reference for tailoring effective metal sulfides-based sorbents to trap iodine from radioactive wastes.

Influence of structural Fe content in clay minerals on selenite redox reactions: Kinetics and structural transformations

Redox reactions control the environmental fate of selenium, an element of concern due to its small gap between beneficial and detrimental effects on human health and due to the longevity of the radionuclide 79Se produced in nuclear reactors. Fe-bearing clay minerals are major redox-active ingredients of Earth’s critical zone and constitute an important component of the barrier in (radioactive and other) waste repositories. Here we systematically investigate selenite (Se(IV)O32−) sorption and reduction by Fe-bearing clay minerals of the smectite group, using batch experiments and X-ray absorption fine structure (XAFS) spectroscopy to elucidate reaction mechanisms and kinetics up to 720 or 3600 h. We found a linear relationship between structural Fe(II) content and selenite reduction rate. Selenite reduction depends also on redox potential and pH, with pH 7 showing a slower reduction rate than at pH 5. Selenite first sorbs to clay edge sites by forming an inner-sphere sorption complex, before being reduced to Se(0). The first redox product was amorphous (red) Se(0), which gradually transformed into trigonal (grey) Se(0), indicative of a kinetically hindered conversion of an amorphous (or less crystalline) solid phase into the thermodynamically stable and more crystalline form of the solid. Despite an Fe2+aq concentration of up to 6·10−4 M in the clay suspension, and their thermodynamic prediction for the clays at lower Eh, we did not observe formation of iron selenides. These insights into the selenite reduction mechanisms by Fe-bearing clays provides valuable information for the development of effective approaches for selenite immobilization.

Fast computational approach with prior dimension reduction for three-dimensional chemical component analysis using CT data of spectral imaging.

Spectral image (SI) measurement techniques, such as X-ray absorption fine structure (XAFS) imaging and scanning transmission electron microscopy (STEM) with energy-dispersive X-ray spectroscopy (EDS) or electron energy loss spectroscopy (EELS), are useful for identifying chemical structures in composite materials. Machine-learning techniques have been developed for automatic analysis of SI data, and their usefulness has been proven. Recently, an extended measurement technique combining SI with a computed tomography (CT) technique (CT-SI), such as CT-XAFS and STEM-EDS/EELS tomography, was developed to identify the three-dimensional (3D) structures of chemical components. CT-SI analysis can be conducted by combining CT reconstruction algorithms and chemical component analysis based on machine learning techniques. However, this analysis incurs high computational costs owing to the size of the CT-SI datasets. To address this problem, this study proposed a fast computational approach for 3D chemical component analysis in an unsupervised learning setting. The primary idea for reducing the computational cost involved compressing the CT-SI data prior to CT computation and performing 3D reconstruction and chemical component analysis on the compressed data. The proposed approach significantly reduced the computational cost without losing information about the 3D structure and chemical components. We experimentally evaluated the proposed approach using synthetic and real CT-XAFS data, which demonstrated that our approach achieved a significantly faster computational speed than the conventional approach while maintaining analysis performance. As the proposed procedure can be implemented with any CT algorithm, it is expected to accelerate 3D analyses with sparse regularized CT algorithms in noisy and sparse CT-SI datasets.

Graphdiyne Enabled Nitrogen Vacancy Formation in Copper Nitride for Efficient Ammonia Synthesis.

The electrocatalytic reduction of nitrate is promising for sustainable ammonia synthesis but suffers from slow reduction kinetics and multiple competing reactions. Here, we report a catalyst featuring copper nitride (Cu3N) anchored on a novel graphdiyne support (termed Cu3N/GDY), which is used for electrocatalytic reduction of nitrate to produce ammonia. The GDY absorbed hydrogen and enabled nitrogen (N) vacancy formation in Cu3N for the fast nitrate reduction reaction (NO3RR). Further, the distinct absorption sites formed by GDY and N vacancy enabled the excellent selectivity and stability of NO3RR. Notably, the Cu3N/GDY catalyst achieved a high ammonia yield (YNH3) up to 35280 μg h-1 mgcat.-1 and a high Faradaic efficiency (FE) of 98.1% using 0.1 M NO3- at -0.9 V versus a reversible hydrogen electrode (RHE). Using electron paramagnetic resonance (EPR) technology and in situ X-ray absorption fine structure (XAFS) spectroscopy measurement, we visualized the N vacancy formation in Cu3N and electrocatalytic NO3RR enabled by GDY. These findings show the promise of GDY in sustainable ammonia synthesis and highlight the efficacy of Cu3N/GDY as a catalyst.

Highly Stable Solid Contact Calcium Ion-Selective Electrodes: Rapid Ion-Electron Transduction Triggered by Lipophilic Anions Participating in Redox Reactions of CunS Nanoflowers.

Solid contact (SC) calcium ion-selective electrodes (Ca2+-ISEs) have been widely applied in the analysis of water quality and body fluids by virtue of the unique advantages of easy operation and rapid response. However, the potential drift during the long-term stability test hinders their further practical applications. Designing novel redox SC layers with large capacitance and high hydrophobicity is a promising approach to stabilize the potential stability, meanwhile, exploring the transduction mechanism is also of great guiding significance for the precise design of SC layer materials. Herein, flower-like copper sulfide (CunS-50) composed of nanosheets is meticulously designed as the redox SC layer by modification with the surfactant (CTAB). The CunS-50-based Ca2+-ISE (CunS-50/Ca2+-ISE) demonstrates a near-Nernstian slope of 28.23 mV/dec for Ca2+ in a wide activity linear range of 10-7 to 10-1 M, with a low detection limit of 3.16 × 10-8 M. CunS-50/Ca2+-ISE possesses an extremely low potential drift of only 1.23 ± 0.13 μV/h in the long-term potential stability test. Notably, X-ray absorption fine-structure (XAFS) spectra and electrochemical experiments are adopted to elucidate the transduction mechanism that the lipophilic anion (TFPB-) participates in the redox reaction of CunS-50 at the solid-solid interface of ion-selective membrane (ISM) and redox inorganic SC layer (CunS-50), thereby promoting the generation of free electrons to accelerate ion-electron transduction. This work provides an in-depth comprehension of the transduction mechanism of the potentiometric response and an effective strategy for designing redox materials of ion-electron transduction triggered by lipophilic anions.

Investigation of hydrothermally-produced ZnO nanorods and the mechanisms of Li incorporation as a possible dopant

Zinc oxide (ZnO) has emerged as one of the most promising candidates for mass-producing cost-efficient optoelectronic devices. This is primarily because it can be synthesized in high-quality nanostructures on a wide range of substrates through relatively simple chemical methods. However, producing p-type ZnO, regardless of the chosen method, remains an open and controversial issue. In this work, Li-doped ZnO nanostructures of varying Li-cocnentration were produced via a two-step hydrothermal growth synthesis and an in-depth analysis based on with Field Emission Scanning Electron Microscopy (FE-SEM), X-ray diffraction (XRD), Raman Spectroscopy, Extended X-Ray Absorption Fine Structure (EXAFS) Spectroscopy, and temperature-dependent Photoluminescence (PL) was carried out in an effort to gain insights into the Li-incorporation mechanisms. The findings indicated a strong interplay between the native defects responsible for the inherent n-type character of the material and Li incorporation. It is suggested that this interplay hinders the successful conversion of the Li-doped nanorods into p-type nanostructures and that when employing the hydrothermal approach it is essential to identify the precise conditions necessary for genuine Li incorporation as a Zn substitutional.

Coexisting single-atomic Fe and Fe2O3 on nitrogen-deficient g-C3N4 with enriched Fenton-like oxidation and photocatalytic performances for tetracycline degradation: DFT calculation, degradation mechanism and toxicity evaluation

The regulation of heterogeneous material properties to strengthen the peroxymonosulfate activation to destroy refractory pharmaceuticals remains a challenge. Herein, a promising nitrogen-deficient catalyst (FeCN) with single atom Fe and Fe2O3 nanoparticles dispersing on g-C3N4 matrix was synthesized and applied as a competent peroxydisulfate (PDS) activator for tetracycline (TC) degradation under visible light. The K-edge X-ray absorption fine structures and 57Fe Mössbauer measurements confirmed the unique configuration of Fe2O3 and single atom Fe active sites (pyrrolic and pyridinic FeN4) induced by the neighbouring nitrogen vacancies. The theory calculations and experiments provided a deep insight into the PDS activation and TC degradation via radical and non-radical pathways. The pyrrolic FeN4 active sites dominated the electron transfer, while the pyridinic FeN4 and Fe2O3 decomposed PDS to produce free radicals. The synergistic effect between the Fenton-like oxidation and photocatalysis is responsible for efficient TC degradation. This study offers a new strategy by integrating novel catalysts and advanced oxidation technology for effective wastewater purification.

Vacancy modulation on NiTi-layered double hydroxides towards highly selective CO2 photoreduction

Photoreduction of carbon dioxide (CO2) is a promising way to achieve sustainable energy production and alleviate environmental problems. Herein, we report a NiTi-layered double hydroxides photocatalyst with bivalent and trivalent metal vacancies (denoted as NiVTiV-LDHs) via alkali-etching amphoteric metal cations (Zn and Al) from NiZnTiAl-LDHs precursor. The NiVTiV-LDHs attains a CH4 selectivity of 94% with a production rate of 2398 µmol g−1 h−1, which is preponderant to the state-of-the-art photocatalysts. Operando X-ray absorption fine structure (XAFS) and Fourier-transform infrared spectroscopy (FT-IR) characterizations combined with density functional theory (DFT) calculations corroborate that Ni2+δ−O(H)−Ti3+ζ sites modulated by adjacent vacancies exhibits a declined 3d-orbital occupancy, accelerating the charge transfer for boosting CH4 formation. Moreover, the unique adsorption configuration (Ni2+δ/Ti3+ζ−CO) not only stabilizes the key intermediate *CO for further protonation, but also induces a decreased energy barrier of the rate-determining step (hydrogenation of *OCH3), accounting for the robust photocatalytic CO2 reduction towards CH4.

Superstructure of Fe5-xGeTe2 Determined by Te K-Edge Extended X-ray Absorption Fine Structure and Te Kα X-ray Fluorescence Holography.

The local structure of the two-dimensional van der Waals material, Fe5-xGeTe2, which exhibits unique structural/magnetic phase transitions, was investigated by Te K-edge extended X-ray absorption fine structure (EXAFS) and Te Kα X-ray fluorescence holography (XFH) over a wide temperature range. The formation of a trimer of Te atoms at low temperatures has been fully explored using these methods. An increase in the Te-Fe distance at approximately 150 K was suggested by EXAFS and presumably indicates the formation of a Te trimer. Moreover, XFH displayed clear atomic images of Te atoms. Additionally, the distance between the Te atoms shortened, as confirmed from the atomic images reconstructed from XFH, indicating the formation of a trimer of Te atoms, i.e., a charge-ordered superstructure. Furthermore, Te Kα XFH provided unambiguous atomic images of Fe atoms occupying the Fe1 site; the images were not clearly observed in the Ge Kα XFH that was previously reported because of the low occupancy of Fe and Ge atoms. In this study, EXAFS and XFH clearly showed the local structure around the Te atom; in particular, the formation of Te trimers caused by charge-ordered phase transitions was clearly confirmed. The charge-ordered phase transition is fully discussed based on the structural variation at low temperatures, as established from EXAFS and XFH.

Negative comonomer effect induced by TiCl3-like clusters in MgCl2-based Ziegler-Natta catalysts

The comonomer effect of ethylene/α-olefin copolymerization in the Ziegler-Natta (Z-N) catalytic system, remaining largely elusive and less understood at the molecular level, has been of huge industrial importance and absorbing research interest for decades. Herein, four catalysts with similar physical structures but different polymerization activities and comonomer effects were synthesized by using n-butanol in combination with different secondary electron donors. By tracking catalyst formation, it was found that altering the secondary donor changes the ν(O-H) stability and in turn the MgCl2 facet growth, to influence the polymerization activity. In situ diffuse reflectance Ultraviolet–visible spectra show that different types of active Ti centers are in function in the ethylene polymerization and the ethylene/1-butene copolymerization. Tracing further the microscopic structures of active species upon triethylaluminium (TEA) activation by using Extended X-ray Absorption Fine Structure, it is found that: (i) for the catalysts with negative comonomer effect, the enhanced donor migration promotes the aggregation of active species and leads to the formation of TiCl3-like clusters; (ii) by contrast, for the catalysts with positive comonomer effect, the less mobile donors hinder the aggregation of active species, thus inducing the formation of isolated Ti3+ sites. Our work reveals an evident correlation between the active center and the comonomer effect, which may be strongly modified by the aggregation of the former.