Weld Bead Research Articles

Study and Characterisation of Bimetallic Structure (316LSI and S275JR) Made by Hybrid CMT WAAM Process

The main objective of this research is to conduct an experimental investigation of the bimetallic material formed by 316LSI stainless steel and S275JR structural steel, produced via hybrid wire arc additive manufacturing technology with cool metal transfer welding and machining, and with the objective of being able to reduce the industrial cost of certain requirements for one of the materials. A methodological investigation has been carried out starting with welding beads of 316LSI on S275JR plates, followed by overlapping five beads and conducting final experiments with several vertical layers, with or without intermediate face milling. The results achieved optimal bead conditions for wire speeds of 4 m/min and 5 m/min at a travel speed of 400 mm/min. Overlap experiments show that the best deposition results are obtained with an overlap equal to or greater than 28%. Cooling time does not significantly influence the final geometry of the coatings. Regarding metallographic analysis, the filler material presents an austenitic columnar structure. In the base material, a bainitic structure with inferred grain refinement was detected in the heat-affected zone. An increase in hardness is observed in the heat-affected zone. In the results obtained from the tensile tests of the bimetallic material, an increase in mechanical strength and yield strength is observed in the tested specimens.

Study on the Electron Beam Repair Welding of 5000 Aluminum Alloys

Electron beam welding (EBW) has been attracted due to its high energy density, high depth-to-width ratio, low thermal strain, compared with arc and laser welding. In addition, it ensures high quality weld joint in structural metals in a wide range of thickness from 0.025 mm to 300 mm. Therefore, EBW is widely used in industries such as automotive, aviation, nuclear power plant, etc. Although a lot of studies on EBW for several decades have been presented, EB based repair welding with supplement of filler metal has less reported. In this work, EB repair welding for 5083 aluminum alloys was investigated because the aluminum alloys are becoming more important as a lightweight material in mobility industries. Material characterization and mechanical properties of the repair-welded specimens were evaluated, compared with characteristics of base metal and bead welding without repair. The optimized experimental conditions showed tensile strength of 294 MPa, which is a similar to base metal. Our study indicates that EB repair welding can be considered for the candidate of repair welding of aluminum alloys.

Enhancement of Additive Manufacturing Processes for Thin-Walled Part Production Using Gas Metal Arc Welding (GMAW) with Wavelet Transform

Additive manufacturing encompasses technologies that produce three-dimensional computer-aided design (CAD) models through a layer-by-layer production process. Compared to traditional manufacturing methods, additive manufacturing technologies offer significant advantages in producing intricate components with minimal energy consumption, reduced raw material waste, and shortened production timelines. AM methods based on shielded gas welding have recently piqued the interest of researchers due to their high efficiency and cost-effectiveness in manufacturing critical components. However, one of the most formidable challenges in additive manufacturing methods based on shielded gas welding lies in the irregularity of weld bead height at different points, compromising the precision of components produced using these techniques. In this current research, we aimed to achieve uniform weld heights along the welding path by considering the most influential parameters on weld bead geometry and conducting experimental tests. Input parameters of the process, including nozzle angle, welding speed, wire speed, and voltage, were considered. Simultaneously, image processing and wavelet transform were employed to assess the uniformity of weld bead height. These parameters were applied to produce intricate parts after identifying optimal parameters that yielded the smoothest weld lines. According to the results, the appropriate bead for manufacturing the part was extracted. The results show that the smoothest bead line is achieved in 27 V as the highest level of voltage, at a 90° nozzle position and the maximum wire feed rate. Parts manufactured using this method across different layers exhibited no distortions, and the repeatability of production substantiated the high reliability of this approach for component manufacturing.

Experimental and Numerical Characterization of Local Properties in Laser-Welded Joints in Thin Plates of High-Strength–Low-Alloy Steel and Their Dependence on the Welding Parameters

Laser welding on thin plates of high-strength steel is increasing in various industrial applications. The mechanical behavior of welded joints depends on their local properties, which in turn depend on the welding parameters applied to join the base material. This work characterizes the local properties of butt-welded joints of thin plates of high-strength–low-alloy (HSLA) steel. This study focuses on the effect of welding parameters on the microstructure, tensile response, microhardness, and weld bead profile. For this purpose, a factorial experimental design was formed, covering a heat input range from 53 to 75 J/mm. This study identified the main effects and interactions of welding speed and laser power on the weld bead profile and on its width. The microstructure, weld bead width, hardness, and tensile mechanical properties were significantly influenced by heat input. Furthermore, numerical simulations on real weld bead profiles revealed high values of the stress concentration factor and suggested a correlation with heat input.

Impact of Heat Input on the Cladding of Super Austenitic Stainless Steel Through the Gas Tungsten Arc Welding Process on ASTM A516 Grade 70 Steel

The cladding process reduces manufacturing costs by depositing super austenitic stainless steel onto low-carbon steel. Arc welding techniques, especially gas tungsten arc welding (GTAW), are commonly used for this purpose. This study evaluates the influence of heat input on cladding performance. Macroscopic analysis showed good fusion of the weld beads to the base metal with no defects. Higher heat input resulted in a lower dilution rate due to increased reinforcement. A microstructural analysis of the heat-affected zones revealed similar characteristics, with martensite formation attributed to cooling conditions. Increased microhardness was observed at the interface between the cladding and base metal, corroborating the microstructural findings. Additionally, a significant enhancement in corrosion resistance was noted in the deposited layers. This research contributes to optimizing cladding processes, ensuring better material performance in industrial applications.

Process development and heat flow analysis for thin walls made of aluminum using extreme high-speed laser material deposition (EHLA3D)

Extreme high-speed laser material deposition (EHLA) is an adapted variant of directed energy deposition (DED-LB-P/M), also known as laser material deposition, and has been developed for the efficient manufacturing of thin layers with high deposition speeds. With precise control of the energy input into the powder gas jet and the substrate, EHLA allows deposition speeds of up to 200 m/min and weld beads as thin as 25 μm. Advantages include a smaller melt pool and a heat-affected zone, allowing the processing of difficult-to-weld material combinations. The development of EHLA for additive manufacturing (EHLA3D) aims to produce highly customized components with improved structural accuracy compared to standard LMD at increased build rates compared to laser powder bed fusion (PBF-LB/M). A promising application is complex lightweight structures for the aerospace industry. However, there is a lack of systematic investigation on lightweight materials processed with EHLA3D at feed rates >20 m/min. In this work, a specially designed tripod machine (maximum feed rate 200 m/min) was used to investigate the buildup of aluminum in process regimes at 30 m/min. After confirming the existing single-track parameters, the tracks were metallographically examined and checked for pores, cracks, and bonding defects. The process was applied to thin-wall geometries and line energies as well as return-times that were varied. To gain an understanding of process-induced heat development, the process was monitored using thermography. Since the process shows geometry-specific heat flow patterns, guidelines have been developed that enable the buildup using different process adaptions.

A Review On Multi objective Optimisation of Process Parameters in Shielded Metal Arc Welding For Joining Stainless Steel 3041 And Mild Steel 1018

Due to Mechanical properties of the welding metal and heat affected zone (HAZ) is quality of welding in this research work the review of Multi-objective optimization of welding process parameters for obtaining best weld strength with good mechanical properties of dissimilar metals like stainless steel 3041 and Mild steel 1018 is done. This process used for welding is shielded Metal Arc welding and dissimilar metal are stainless steel 3041 and mild steel 1018. Welding speed, depend on electric property like current Voltage electrode angle, feed rate, Arc length are taken as controlling variables. The weld strength (N/mm2) and Bead geometry variables and Heat Affected Zone are obtained by set of experiment, the possible best outcomes and best method has been chosen by this research. Keywords: HAZ, Multi objective optimization, Response surface Methodology, Shielded metal arc welding

Effect of slag recycling on bead geometry, dilution and microstructure in submerged arc cladding of stainless steels

The submerged arc welding (SAW) process generates a large quantity of slag, which, when disposed-of, harms the environment and wastes valuable ingredients. A technology was developed to recycle the SAW slag generated in stainless steel cladding, enabling its reuse as flux. Bead geometry and dilution play crucial roles in weld cladding. Dilution determines the minimum number of layers needed to achieve the desired chemistry, while bead width dictates the fewest passes required to cover the entire surface area. Additionally, bead geometry influences the mechanical strength of the clad layers. The microstructure and solidification mode also significantly affect clad quality. Therefore, understanding the impact of recycled slag on bead geometry, dilution, and microstructure is essential. This paper presents a systematic investigation into the effects of process variables and recycled slag on bead geometry and dilution in clad welding. It includes a comparison of microstructures obtained using fresh flux versus recycled slag. The results indicate that increasing the welding current (I) by 37.5% enhances weld penetration (p), bead width (w), reinforcement (r), and dilution (d) by 50.9%, 14.4%, 69.5%, and 5.5%, respectively. Conversely, increasing the travel speed (V) by 90%, decreases p, w, and r by 19.29%, 11.9%, and 25.3%, respectively; however, dilution (d) increases by 17.6%. On the other hand, increasing the open-circuit voltage (V) by 26.7% increases bead width (w) and dilution (d) by 10.4% and 5.4%, respectively, while reinforcement (r) decreases by 7.5%. Both single and multilayer claddings prepared with fresh flux and recycled slag exhibit similar microstructures.

Mathematical model for estimation of strength and weld bead geometry of dissimilar metal laser welds

Mathematical model for estimation of strength and weld bead geometry of dissimilar metal laser welds

Effect of Microgravity on the Metal Droplet Transfer and Bead Characteristics in the Directed Energy Deposition-Arc Process

Abstract Directed energy deposition-arc (DED-arc) is a viable method of metal 3D printing for manufacturing in-space under microgravity conditions. This study investigates the effect of reduced gravity on the droplet transfer in a gas metal arc welding (GMAW)-based DED-arc process. Single bead deposited using GMAW welding process under microgravity and standard terrestrial gravity (1 g) are compared. Microgravity was simulated in a drop tower where the experimental capsule was subjected to 2.5 s of free-fall. The experimental setup for GMAW welding process, including high-speed cameras and sensors, was present within the experimental capsule. Droplet frequency and diameter were measured and compared between microgravity and 1 g using the images obtained. Further, the impact of reduced gravity on weld bead geometry and the distribution of gas porosity was investigated. Microhardness analysis was also conducted on both 1 g and reduced gravity samples to assess variations in material hardness. A statistically significant difference in droplet diameter and frequency was found. This difference is attributed to the reduction in gravitational force. Upon analyzing the weld bead geometry, noticeable variations are detected in the contact angles and the reinforcement of beads formed under different gravity conditions. These differences are attributed to alterations in convection within the molten weld pool. The blowhole analysis revealed a noticeable trend, wherein reduced gravity facilitated the coalescence of gas porosity, resulting in larger diameters due to alterations in weld pool convection. There were no statistically significant changes observed in both microhardness and surface finish.

Weld Pool Flow Characteristics in Double-Wire Arc Welding of Aluminum Alloys: Research by Numerical Simulations

Double-wire arc welding involves simultaneously feeding two wires into a molten pool, improving the efficiency and flexibility of traditional welding techniques. However, the interactions between the two wires and the molten pools are complex, which increases the difficulties in process and composition control. This work focuses on the weld pool flow characteristics in double-wire TIG arc welding. A CFD model incorporating a liquid bridge transfer model was developed to simulate the fluid flow phenomenon. Results show that the bead-forming appearances and flow characteristics of double-wire arc welding show no significant differences from single-wire arc welding. Welding current and welding speed have significant effects on the weld bead dimensions, while only welding current has effects on the flow characteristics. Wire feed XOZ angles show no significant influences on weld bead forming appearances and molten pool flow characteristics. Wire feed XOY angles influence the symmetry of the weld bead and the fluid flow. In 5B71/7055 heterogeneous double-wire arc welding, achieving a uniform distribution of alloy elements is difficult due to the complex convection patterns within the molten pool.

Parametric optimization of weld bead of aluminium 6061 fabricated through wire arc additive manufacturing

Parametric optimization of weld bead of aluminium 6061 fabricated through wire arc additive manufacturing

Phase quantification in a duplex stainless steel welds using NDT techniques

ABSTRACT Duplex stainless steels are composed of ferrite and austenite in equal volume fractions of these phases, which provides an excellent combination of mechanical properties and corrosion resistance, especially when compared with conventional stainless steel grades. When these steels are welded, there are significant changes in the austenite-to-ferrite ratio therefore in their final properties. Nowadays, the ferritoscope is the unique non-destructive technique used to quantify these two phases content in situ. This tester instrument is limited to the evaluation of large areas, is not suitable for the heat affected zone and is also very sensitive to the surface finish, being considered an intermediate precision technique. So, it is necessary to develop more reliable field techniques. In this research, thermoelectric power measurements and induced current techniques are proposed to evaluate the phase quantification in S32205 welds. According to the results, both techniques are reliable and highly sensitive to phase changes in the weld bead, heat affected zone and base metal. For the thermoelectric power technique, a probe with nickel tip should be used to obtain the highest sensitivity and for the induced current technique, a probe type-pencil with a central frequency of 6 MHz should be used.

A Study on the Green Laser Weldability of Copper-aluminum Battery Materials

Copper is widely utilized in electric vehicle batteries due to its excellent electrical conductivity, lightweight, and excellent corrosion resistance. However, copper has a high reflectivity of about 97% for infrared lasers, which makes it difficult to achieve stable welding quality. This study investigated using a green laser to weld nickel-coated copper and aluminum materials. After performing welding by changing the laser power and scan speed, the weld cross-section was observed with an optical microscope, and it was confirmed that the welding penetration depth and bead width increased as the heat input increased. The spatter on the bead surface and defects such as pores and cracks in the weld were caused by excessive heat input. Analysis of the weld cross-section using SEM-EDS showed that high heat input increased the formation of intermetallic compounds including CuAl2 and Cu9Al4. The mechanical properties of the weld were examined using a shear tensile test. The analysis results showed that intermetallic compounds caused brittleness in the weld joint, which lowered mechanical properties and caused defects such as pores and cracks. P60 (1.2 kW, scan speed: 250 mm/s), P80 (1.6 kW, scan speed: 375 mm/s), and P100 (1.2 kW, scan speed: 375 mm/s) were examples of excellent mechanical quality. The fastest welding condition, P100 (power: 2 kW, scan speed: 450 mm/s), was suggested as the most efficient welding condition.

Fabricating complex parts through optimizing weld bead geometry in WAAM: A comparative study of surface tension transfer and cold metal transfer

Wire arc additive manufacturing (WAAM) technology is being employed in industries such as aerospace, maritime and automotive to produce high-valued metallic parts. With a growing demand for products with complex structures, it is crucial to develop an effective and reliable method for fabricating such parts to meet the demand. Currently, cold metal transfer (CMT), is one of the waveform-controlled short circuit transfer processes, commonly adopted in the WAAM process to fabricate medium to large-scale parts due to its perceived low heat input. However, the approach of using synergic control of wire feed speed and torch travel speed to control weld bead geometry in CMT may not be applicable for fabricating parts with complex structures. In these circumstances, surface tension transfer (STT), a waveform controlled short circuit transfer process, or one of the alternative variants of controlled short circuit transfer with low heat input, may provide more options to control weld bead geometry. There appear to have been few systematic investigations of alternative controlled short circuiting variants for use in WAAM. This paper provides a comparative study to explore the potential of the STT process for fabricating parts with complex geometries in WAAM. Firstly, the working principles of the STT and CMT processes are reviewed. Then, the impacts of welding parameters in the STT and CMT on weld bead geometry are analysed based on experiment results. Finally, a comparison between these two welding processes with regard to flexibility in welding parameter adjustment, heat input and overlapping performance is conducted. Finally, a comparison between these two welding processes is conducted from three critical aspects: (i) Flexibility in parameter adjustment: STT has 333 % and 174 % larger average width and height variation ranges than CMT; (ii) Heat input: STT's heat input is 74.66 % higher than CMT's at TS = 300 mm/min; (iii) Overlapping performance: the average surface roughness of the tested CMT and STT groups is 0.1312 and 0.1823, respectively. Suggestions for using STT and CMT to fabricate parts with complex geometries are provided accordingly.

Effect of welding gas mixtures on weld material and bead geometry

Abstract Shielding gas is an essential parameter in welding processes, serves to shield the molten material from the atmosphere and external contaminations while providing a stable electric-arc pathway during the process, thus influencing the quality of the weld bead and several other aspects of the process. Therefore, any welding-based process, such as wire-arc additive manufacturing, could benefit from shielding gas mixture optimisation to selectively improve the processing and possibly the final mechanical properties of the welded material. In this study welding of EN AW 5183 aluminium (single weld bead and wire-arc additive manufacturing build-up) was conducted using several gas mixtures and their influence on final geometry defects, and microstructure measured. The gas mixtures used were a combination of varying amounts of carbon dioxide, nitrogen, and oxygen. These were added to commercially available argon gas. It was observed that: CO2 additions led to an unfavourable bonding defect and increased mean grain size; nitrogen additions caused a decrease in mean grain size, decreased pore count while maintaining a similar pore volume fraction to the reference argon mixture samples; oxygen additions showed slight reduction of mean grain size, decreased pore count and decreased pore volume fraction. These results further showcase that varying shielding gas mixtures influence the final material properties and should be considered as an additional improvement route for conventional welding and additive manufacturing.

Effect of laser beam incident angle on welding of Ti6Al4V with fiber lasers

Laser beam welding (LBW) is widely used for welding Ti6Al4V alloys in aerospace applications. LBW has localized high-energy fluence with low-energy input compared to other fusion welding processes, resulting in narrower heat-affected zones. On the other hand, most metals are highly reflective when the laser beam impinges perpendicular to the surface, making the process inefficient. Hence, this work proposes to employ shallow angle incidence to reduce the reflectivity during the welding of Ti6Al4V material. To explore the potential of this idea, the current study focuses on studying the effect of laser incident angle (15°-90°), power (300 W-1500 W), and feed rate (10 mm/s-25 mm/s) on autogenous weld bead geometry. For this purpose, bead-on plate (BOP) LBW is conducted on mill-annealed Ti6Al4V material of dimensions 25 mm × 25 mm × 3 mm by employing a fiber laser source with a maximum power of 3 kW and a wavelength of 1080 nm. It is observed from the results that at a normal incident angle and low laser power (< 600 W), the penetration depth is too low to generate a weld bead. Analyzing the cross-section of the weld bead, obtained from SEM, perpendicular to the weld direction reveals that the increase in laser incident angle up to an optimal angle resulted in increased bead dimensions (width and height), and beyond that, the dimensions decreased. However, the optimal incident angle changed when the laser power was changed. The major finding of this study is that at 600 W and a normal incident angle, the laser could not penetrate and generate a weld bead due to low absorptivity, while at an incident angle of 300, 450, and 600, weld beads are generated because of increased absorptivity. Similarly, the increase in weld dimensions with the increase in laser power is observed. At higher laser power, underfill and oxide formation are observed. The feed rate is less predominant than the incident angle and the power.

Dissimilar MIG Welding Optimization of C20 and SUS201 by Taguchi Method

This study looks at how welding intensity, speed, voltage, and stick-out affect the structural and mechanical characteristics of metal inert gas (MIG) welding on SUS 201 stainless steel and C20 steel. The Taguchi method is used to optimize the study’s experiment findings. The results show that the welding current has a more significant effect on the tensile test than the welding voltage, stick-out, and welding speed. Welding voltage has the lowest influence. In addition to the base metals’ ferrite, pearlite, and austenite phases, the weld bead area contains martensite and bainite microstructures. The optimal parameters for the ultimate tensile strength (UTS), yield strength, and elongation values are a 110 amp welding current, 15 V of voltage, a 500 mm.min−1 welding speed, and a 10 mm stick-out. The confirmed UTS, yield strength, and elongation values are 452.78 MPa, 374.65 MPa, and 38.55%, respectively, comparable with the expected value derived using the Taguchi method. In the flexural test, the welding current is the most critical element affecting flexural strength. A welding current of 110 amp, an arc voltage of 15 V, a welding speed of 500 mm.min−1, and a stick-out of 12 mm are the ideal values for flexural strength. The flexural strength, confirmed at 1756.78 MPa, is more than that of the other samples. The study’s conclusions can offer more details regarding the dissimilar welding industry.

Real-time monitoring and control of the layer height in laser metal deposition with coaxial wire feeding using optical coherence tomography

Laser metal deposition (LMD) with coaxial wire feeding is an additive manufacturing technology in which a metal wire is fed into a laser-induced melt pool. The repeated deposition of weld beads allows three-dimensional geometries to be created that can be used for manufacturing, repair, and modification of metal components. However, the process is highly sensitive to disturbances because the fed wire must always be fully melted, and no self-regulating effects as in powder-based LMD exist. The layer height is particularly important for process stability, as even small deviations accumulate over many layers and, ultimately, lead to the termination of the process. Therefore, monitoring and closed-loop control of the layer height during the deposition process are crucial. Due to process emissions, an interruption of the process is usually necessary for the accurate optical measurement of the layer height, which negatively affects the overall productivity. In order to overcome this drawback, an in-axis optical coherence tomography (OCT) sensor was employed in this work, which enabled real-time measurements of the layer height. It was found that positioning the OCT measurement spot as close as possible to the center of the wire provided the highest signal quality. Based on the real-time height data, a closed-loop layer height control was implemented, applying the wire feed rate as the manipulated variable. The experimental results showed that the proposed system was able to compensate for significant disturbances, ensuring dimensional accuracy and process stability.

Microhardness and element transfer investigation of weld bead using formulated SiO2−CaO−CaF2−BaO SMAW electrode coatings

Microhardness and element transfer investigation of weld bead using formulated SiO2−CaO−CaF2−BaO SMAW electrode coatings