Violet Light-emitting Diodes Research Articles

A facile Pt-doped g-C3N4 photocatalytic biosensor for visual detection of superoxide dismutase in serum samples

In this work, we reported a photocatalytic biosensor for visual detection of superoxide dismutase (SOD) based on Pt-doped graphite phase carbon nitride (g-C3N4). Upon illumination by a violet light-emitting diode (LED), Pt-doped g-C3N4 absorbed the light energy and catalytically produced O2− which further oxidized the dyes into a colorless end product. In the presence of SOD, it can specifically catalyze O2− into oxygen and hydrogen peroxide, leading to a reduced photooxidation and a visual color display. After screening a series of dyes, the azo dye amaranth (AM) was proven to be the best indicator for O2− since the azo bond is active and easily oxidized by O2−, resulting in a low background. Such a simple photocatalytic sensor allows visual detection of SOD at a nM level without the need of any sophisticated instrument; using spectrometry, the linear response for SOD detection ranges from 1.5 to 4500 nM with a limit of detection (LOD, 3σ) down to 0.3 nM. The sensor was also successfully applied for label-free and wash-free detection of SOD in human serum samples with a satisfactory recovery.

Visible Light as an Antimicrobial Strategy for Inactivation of Pseudomonas fluorescens and Staphylococcus epidermidis Biofilms

The increase of antimicrobial resistance is challenging the scientific community to find solutions to eradicate bacteria, specifically biofilms. Light-Emitting Diodes (LED) represent an alternative way to tackle this problem in the presence of endogenous or exogenous photosensitizers. This work adds to a growing body of research on photodynamic inactivation using visible light against biofilms. Violet (400 nm), blue (420 nm), green (570 nm), yellow (584 nm) and red (698 nm) LEDs were used against Pseudomonas fluorescens and Staphylococcus epidermidis. Biofilms, grown on a polystyrene surface, were irradiated for 4 h. Different irradiance levels were investigated (2.5%, 25%, 50% and 100% of the maximum irradiance). Surviving cells were quantified and the inactivation kinetic parameters were estimated. Violet light could successfully inactivate P. fluorescens and S. epidermidis (up to 6.80 and 3.69 log10 reduction, respectively), while blue light was effective only against P. fluorescens (100% of maximum irradiance). Green, yellow and red irradiation neither increased nor reduced the biofilm cell density. This is the first research to test five different wavelengths (each with three intensities) in the visible spectrum against Gram-positive and Gram-negative biofilms. It provides a detailed study of the potential of visible light against biofilms of a different Gram-nature.

3D Microlithography Using an Integrated System of 5-mm UV-LEDs with a Tilt-Rotational Sample Holder

This paper demonstrates a 3D microlithography system where an array of 5 mm Ultra Violet-Light Emitting Diode (UV-LED) acts as a light source. The unit of the light source is a UV-LED, which comes with a length of about 8.9 mm and a diameter of 5 mm. The whole light source comprises 20 × 20 matrix of such 5 mm UV-LEDs giving a total number of 400 LEDs which makes it a very favorable source with a large area for having a batch production of the desired microstructures. This light source is able to give a level of precision in microfabrication which cannot be obtained using commercial 3D printers. The whole light source performs continuous rotational movement once it is turned on. This can also move up and down in a vertical direction. This multidirectional light source also comprises a multidirectional sample holder. The light source teaming up with the multidirectional sample holder highly facilitates the process of fabrication of a huge range of 3D structures. This article also describes the different levels of characterization of the system and demonstrates several fabricated 3D microstructures including high aspect ratio vertical micro towers, twisted turbine structures, triangles, inclined pillar ‘V’ structures, and hollow horn structures as well.

Violet Light-Emitting Diodes Based on p-CuI Thin Film/n-MgZnO Quantum Dot Heterojunction.

As the lighting technology evolves, the need for violet light-emitting diodes (LEDs) is growing for high color rendering index lighting. The present technology for violet LEDs is based on the high-cost GaN materials and metal-organic chemical vapor deposition process; therefore, there have recently been intensive studies on developing low-cost alternative materials and processes. In this study, for the first time, we demonstrated violet LEDs based on low-cost materials and processes using a p-CuI thin film/n-MgZnO quantum dot (QD) heterojunction. The p-CuI thin film layer was prepared by an iodination process of Cu films, and the n-MgZnO layer was deposited by spin-coating presynthesized n-MgZnO QDs. To maximize the performance of the violet LED, an optimizing process was performed for each layer of p- and n-type materials. The optimized LED with 1 × 1 mm2-area pixel fabricated using the p-CuI thin film at the iodination temperature of 15 °C and the n-MgZnO QDs at the Mg alloying concentration of 2.7 at. % exhibited the strongest violet emissions at 6 V.

Photodynamic therapy in 2D and 3D human cervical carcinoma cell cultures employing LED light sources emitting at different wavelengths

Light of different wavelengths can be used to obtain a more profitable outcome of photodynamic therapy (PDT), according to the absorption bands of the photosensitizer (PS). Low-grade cervical intraepithelial neoplasias (CINs) are superficial lesions that can be treated with light of shorter wavelength than red because a large light penetration depth in tissue is not necessary. We report a comparative investigation performed to evaluate the efficacy of light-emitting diodes (LEDs) of different wavelengths in the photodynamic treatment applied to both 2D and 3D HeLa cell spheroid cultures. The spheroids are utilized as a PDT dosage model, and cell viability is evaluated at different sections of the spheroids by confocal microscopy. Cells incubated with m-tetrahydroxyphenyl chlorin are illuminated with LED systems working in the low fluence range, emitting in the violet (390–415 nm), blue (440–470 nm), red (620–645 nm) and deep red (640–670 nm) regions of the light spectrum at various exposures times (tI) comprised between 0.5 and 30 min. PDT experiments performed on both 2D and 3D cell cultures indicate that the PDT treatment outcome is more efficient with violet light followed by red light. Dynamic data from the front displacement velocity of large 2D-quasi-radial colonies generated from cell spheroids adhered to the Petri dish bottom as well as the evolution of the 3D growth give further insight about the effect of PDT at each condition. Results from 3D cultures indicate that the penetration of the violet light is appropriate to kill HeLa cells several layers below, showing cell damage and death not only in the outer rim of the illuminated spheroids, where a PS accumulation exists, but also in the more internal region. Results indicate that violet LED light could be useful to treat CINs involving superficial dysplasia.

Influence of Multiple Peak Light-emitting-diode Curing Unit Beam Homogenization Tips on Microhardness of Resin Composites.

This study evaluated the effect of light curing unit (LCU) guide type (regular or homogenizing) on top and bottom microhardness of conventional and bulk-fill resin-based composites (RBCs). A polywave light-emitting-diode (LED) LCU (Bluephase Style, Ivoclar Vivadent AG) was used with two different light guides: a regular tip (RT, 935 mW/cm2 emittance) and a homogenizer tip (HT, 851 mW/cm2 emittance). Two conventional RBCs (Herculite Ultra [HER], Kerr Corp; Tetric EvoCeram [TEC], Ivoclar Vivadent AG) and two bulk-fill RBCs (SonicFill [SOF], Kerr Corp; Tetric EvoCeram Bulk Fill [TBF], Ivoclar Vivadent AG) were tested. Disc-shaped samples (10 mm Ø), 2-mm thick for conventional composites and 4-mm thick for bulk-fill composites were prepared. Samples were light cured according to manufacturer-recommended times. Knoop microhardness values (KHN) were obtained on the top and bottom surfaces of each specimen at locations correlated with the output of the three LED chips emitting blue (456 nm) or violet light (409 nm). Beam profile analysis using both light guides was also performed. Microhardness of each composite was analyzed using three-way analysis of variance and Tukey honestly significant difference post hoc test (α=0.05). Beam profile images showed better light distribution across the surface of the HT light guide. Use of the HT decreased KHN of HER at the locations of the blue LED chips at bottom of the sample but had no effect on the top surface. For TEC, use of HT increased KHN of all three LED locations at the top surface. Use of the HT increased KHN of SOF at locations corresponding to one of the blue and the violet LED chips at the bottom surface. For TBF, HT increased KHN at all top surface locations. All RBCs showed higher mean KHN at the top compared with the bottom surfaces. In general, all composites presented a higher KHN at the blue LED areas regardless of the surface or the tip used. Results suggest that the homogenizer light guide resulted in significantly increased microhardness at the top, in composite resins containing alternative photoinitiators; however, that effect was not observed at the bottom surfaces.

Characterization of excitation source LEDs and sensors without filters for measuring fluorescence in fluorescein and green leaf extract

This paper presents the characterization of excitation source LEDs and sensors without filters for measuring fluorescence in fluorescein and green leaf extract. For this purpose, eight light-emitting diodes (LEDs) were used with the following characteristics: one blue, one green, one red, one infrared, and four violets. The first four LEDs were used as sensors without filters to detect fluorescence induced by the other four violet LEDs in 11 samples of different fluorescein concentrations and in 14 samples of different dilutions of green leaf extract. The results show that infrared LEDs can detect the red emission of green leaf extract and red and infrared LEDs detect the fluorescence of fluorescein in concentrations of up to 1.8 μM. The developed system allows and facilitates teaching optical spectroscopy in basic education without incurring high costs.

Epitaxy of III-Nitrides on β-Ga2O3 and Its Vertical Structure LEDs

β-Ga2O3, characterized with high n-type conductivity, little lattice mismatch with III-Nitrides, high transparency (>80%) in blue, and UVA (400–320 nm) as well as UVB (320–280 nm) regions, has great potential as the substrate for vertical structure blue and especially ultra violet LEDs (light emitting diodes). Large efforts have been made to improve the quality of III-Nitrides epilayers on β-Ga2O3. Furthermore, the fabrication of vertical blue LEDs has been preliminarily realized with the best result that output power reaches to 4.82 W (under a current of 10 A) and internal quantum efficiency (IQE) exceeds 78% by different groups, respectively, while there is nearly no demonstration of UV-LEDs on β-Ga2O3. In this review, with the perspective from materials to devices, we first describe the basic properties, growth method, as well as doping of β-Ga2O3, then introduce in detail the progress in growth of GaN on (1 0 0) and (−2 0 1) β-Ga2O3, followed by the epitaxy of AlGaN on gallium oxide. Finally, the advances in fabrication and performance of vertical structure LED (VLED) are presented.

A New Approach for Dental Bleaching Using Violet Light With or Without the Use of Whitening Gel: Study of Bleaching Effectiveness.

The objective of this study was to evaluate the effectiveness of violet light-emitting diodes (LEDs) in dental bleaching treatment when used in conjunction with bleaching gels containing different concentrations of hydrogen peroxide (HP). Here, 90 bovine teeth (n=15) were randomly assigned to the following groups: GI, placebo without light; GII, 35% HP without light; GIII, 17.5% HP without light; GIV, placebo with violet LED; GV, 35% HP with violet LED; and GVI, 17.5% HP with violet LEDs. Three bleaching sessions of 45 minutes were conducted; 21 cycles involving one minute of irradiation by violet LEDs with 30-second intervals were performed during each session of bleaching (GIV, GV, and GVI). Color changes (ΔE, ΔL, Δa, and Δb) were analyzed using a visible ultraviolet light spectrophotometer 7 days after each bleaching session. The mean ΔE, ΔL, Δa, and Δb values were compared between groups by analysis of variance and Tukey tests, with a significance level of 5%. The groups treated with 35% HP had higher ΔE and ΔL and lower Δb values, regardless of whether violet light was used. The group that received only violet LED differed from the control group in terms of ΔE, and the group treated with 17.5% HP and violet LED presented higher ΔE values than the group treated with 17.5% HP only. Thus, violet light did not influence bleaching efficacy when using 35% HP, but when used in conjunction with 17.5% HP, it increased the bleaching efficacy. Moreover, use of the violet LED only also prompted a bleaching effect, although it was less marked.

Sonochemical Synthesis of Ce-doped TiO2 Nanostructure: A Visible-Light-Driven Photocatalyst for Degradation of Toluene and O-Xylene.

Ce-doped TiO2 nanostructures (CeT) with different amounts of Ce (0.5, 0.75, 1.0, 1.5, and 2.0 wt. %) were synthesized using a sonochemical processing method. The physicochemical properties of the prepared samples were explored using UV-visible diffuse reflectance spectroscopy (UV-vis DRS), field-emission TEM (FE-TEM), XRD, X-ray photoelectron spectroscopy (XPS), photoluminescence spectroscopy (PL), and surface area and pore size analyzers. The photocatalytic performance of the prepared CeT was assessed by monitoring their degradation efficiencies for gaseous toluene and o-xylene—widely known as significant indoor air pollutants—under daylight irradiation. The prepared CeT exhibited significantly improved photocatalytic performance towards the degradation of toluene and o-xylene, which was much higher than that observed for pure TiO2 and commercial P25 TiO2. Particularly, photocatalytic degradation efficiencies by the prepared CeT catalysts increased remarkably in the case of o-xylene (up to 99.4%) compared to toluene (up to 49.1%). The degradation efficiency by the CeT was greatest for the CeT-0.75 sample, followed by, in order, CeT-1.0, CeT-0.5, CeT-1.5, and CeT-2.0 samples in agreement with the order of the surface area and the particle size of the catalysts. According to the change of light source, the average decomposition efficiencies for toluene and o-xylene by CeT-0.75 were shown in the order of conventional daylight lamp > violet light emitting diodes (LEDs) > white LEDs. The decomposition efficiencies normalized to supplied electric power, however, were estimated to be in the following order of violet LEDs > white LEDs > conventional daylight lamp, indicating that the LEDs could be a much more energy efficient light source for the photodecomposition of target toluene and o-xylene using the CeT-0.75 photocatalyst.

Carrier transport mechanisms of InGaN-based light-emitting diodes using a single pulsed current

The current-voltage characteristics of InGaN-based light-emitting diodes (LEDs) with various In compositions are analyzed. The emission spectra and ideality factors of ultraviolet, violet, and blue LEDs are investigated in a single pulsed current mode. A comparison of the emission spectra shows that with an increase in the current density, diffusion, recombination, and tunneling dominate the carrier transport mechanism, and a correlation exists between the carrier transport mechanisms and the broadening of the emission spectrum. However, the increase in defect-related emissions and the blue shift of the emission peak are more noticeable with an increase in the current density in In-rich blue LEDs. Theoretical modeling revealed that the carrier density increases drastically when the current density is above a certain threshold. The increase in carrier density in the quantum well causes a growth of the carrier tunneling, recombination, diffusion, and overflow due to which the ideality factor and efficiency decrease.

Luminescence Spectra of High-Power Violet and Ultraviolet Gallium Nitride-Based LEDs

The electroluminescence spectra of high-power light-emitting diodes (LEDs) based on p–n heterostructures of the InGaN/AlGaN/GaN type emitting in the visible short-wavelength and ultraviolet spectral regions (the range from 370 to 460 nm) are investigated. The shape of spectra is described by a model taking into account a two-dimensional combined density of states and potential fluctuations. Additional long-wavelength peaks are found in emission spectra. The emission power of ultraviolet and violet LEDs reaches 233 mW at a current of 350 mA, and the external quantum yield reaches 23% at the maximum (near a current of 100 mA).

C60 fullerene accumulation in human leukemic cells and perspectives of LED-mediated photodynamic therapy

Recent progress in nanobiotechnology has attracted interest to a biomedical application of the carbon nanostructure C60 fullerene since it possesses a unique structure and versatile biological activity. C60 fullerene potential application in the frame of cancer photodynamic therapy (PDT) relies on rapid development of new light sources as well as on better understanding of the fullerene interaction with cells.The aim of this study was to analyze C60 fullerene effects on human leukemic cells (CCRF-CEM) in combination with high power single chip light-emitting diodes (LEDs) light irradiation of different wavelengths: ultraviolet (UV, 365 nm), violet (405 nm), green (515 nm) and red (632 nm). The time-dependent accumulation of fullerene C60 in CCRF-CEM cells up to 250 ng/106 cells at 24 h with predominant localization within mitochondria was demonstrated with immunocytochemical staining and liquid chromatography mass spectrometry. In a cell viability assay we studied photoexcitation of the accumulated C60 nanostructures with ultraviolet or violet LEDs and could prove that significant phototoxic effects did arise. A less pronounced C60 fullerene phototoxic effect was observed after irradiation with green, and no effect was detected with red light. A C60 fullerene photoactivation with violet light induced substantial ROS generation and apoptotic cell death, confirmed by caspase3/7 activation and plasma membrane phosphatidylserine externalization. Our work proved C60 fullerene ability to induce apoptosis of leukemic cells after photoexcitation with high power single chip 405 nm LED as a light source. This underlined the potential for application of C60 nanostructure as a photosensitizer for anticancer therapy.

Polystyrene Oxygen Optodes Doped with Ir(III) and Pd(II) meso-Tetrakis(pentafluorophenyl)porphyrin Using an LED-Based High-Sensitivity Phosphorimeter.

This paper presents a gaseous oxygen detection system based on time-resolved phosphorimetry (time-domain), which is used to investigate O optical transducers. The primary sensing elements were formed by incorporating iridium(III) and palladium(II) meso-tetrakis(pentafluorophenyl)porphyrin complexes (IrTFPP-CO-Cl and PdTFPP) in polystyrene (PS) solid matrices. Probe excitation was obtained using a violet light-emitting diode (LED) (low power), and the resulting phosphorescence was detected by a high-sensitivity compact photomultiplier tube. The detection system performance and the preparation of the transducers are presented along with their optical properties, phosphorescence lifetimes, calibration curves and photostability. The developed lifetime measuring system showed a good signal-to-noise ratio, and reliable results were obtained from the optodes, even when exposed to moderate levels of O. The new IrTFPP-CO-Cl membranes exhibited room temperature phosphorescence and moderate sensitivity: <>/<> ratio of ≈6. A typically high degree of dynamic phosphorescence quenching was observed for the traditional indicator PdTFPP: <>/<> ratio of ≈36. Pulsed-source time-resolved phosphorimetry combined with a high-sensitivity photodetector can offer potential advantages such as: (i) major dynamic range, (ii) extended temporal resolution (/[O]) and (iii) high operational stability. IrTFPP-CO-Cl immobilized in polystyrene is a promising alternative for O detection, offering adequate photostability and potentially mid-range sensitivity over Pt(II) and Pd(II) metalloporphyrins.

Highly stable and tunable white luminescence from Ag-Eu3+ co-doped fluoroborate glass phosphors combined with violet LED.

Ag-Eu3+ co-doped fluoroborate glass phosphors doped with various Eu3+-concentrations were prepared by a melt-quenching technique. The luminescent properties of these glass phosphors were characterized by excitation and emission spectra. Broad excitation and emission bands located, respectively, at 300-450 nm and 390-700 nm originating from silver aggregates were observed. Strong red emissions were detected under 404 nm violet light-emitting diode (LED) excitation for those Ag-Eu3+ co-doped samples. It was found that these red emissions of Eu3+ well compensated the deficiency of the red spectral components in glasses containing Ag aggregates. In addition, it was confirmed that stable white light could be achieved from the combination of a specific Ag-Eu3+ co-doped fluoroborate glass phosphor and LEDs with different output wavelengths. By adjusting the luminescence intensity ratio of the glass phosphor to the 404 nm violet LED, tunable emitting color was realized, and the studied glass phosphors showed excellent emitting color stability toward LED drive currents. Our results demonstrated that this kind of easy fabrication, low-cost, and highly stable Ag-Eu3+ co-doped fluoroborate glass phosphors had potential application in white LED.

Спектры люминесценции мощных светодиодов на основе нитрида галлия в ультрафиолетовой и фиолетовой областях спектра

AbstractThe electroluminescence spectra of high-power light-emitting diodes (LEDs) based on p – n heterostructures of the InGaN/AlGaN/GaN type emitting in the visible short-wavelength and ultraviolet spectral regions (the range from 370 to 460 nm) are investigated. The shape of spectra is described by a model taking into account a two-dimensional combined density of states and potential fluctuations. Additional long-wavelength peaks are found in emission spectra. The emission power of ultraviolet and violet LEDs reaches 233 mW at a current of 350 mA, and the external quantum yield reaches 23% at the maximum (near a current of 100 mA).

Can narrow-bandwidth light from UV-A to green alter secondary plant metabolism and increase Brassica plant defenses against aphids?

Light of different wavelengths is essential for plant growth and development. Short-wavelength radiation such as UV can shift the composition of flavonoids, glucosinolates, and other plant metabolites responsible for enhanced defense against certain herbivorous insects. The intensity of light-induced, metabolite-based resistance is plant- and insect species-specific and depends on herbivore feeding guild and specialization. The increasing use of light-emitting diodes (LEDs) in horticultural plant production systems in protected environments enables the creation of tailor-made light scenarios for improved plant cultivation and induced defense against herbivorous insects. In this study, broccoli (Brassica oleracea var. italica) plants were grown in a climate chamber under broad spectra photosynthetic active radiation (PAR) and were additionally treated with the following narrow-bandwidth light generated with LEDs: UV-A (365 nm), violet (420 nm), blue (470 nm), or green (515 nm). We determined the influence of narrow-bandwidth light on broccoli plant growth, secondary plant metabolism (flavonol glycosides and glucosinolates), and plant-mediated light effects on the performance and behavior of the specialized cabbage aphid Brevicoryne brassicae. Green light increased plant height more than UV-A, violet, or blue LED treatments. Among flavonol glycosides, specific quercetin and kaempferol glycosides were increased under violet light. The concentration of 3-indolylmethyl glucosinolate in plants was increased by UV-A treatment. B. brassicae performance was not influenced by the different light qualities, but in host-choice tests, B. brassicae preferred previously blue-illuminated plants (but not UV-A-, violet-, or green-illuminated plants) over control plants.

Temperature dependence of the optical properties of violet, blue and green InGaN/GaN single quantum well light-emitting diodes

Temperature dependence of the optical properties of InGaN/GaN single quantum well light-emitting diodes (LEDs) with different indium (In) contents is investigated by using the effective mass theory taking into account the band-gap shrinkage and lattice thermal expansion. The peak intensity of the spontaneous emission spectrum is decreased by 30.6%, 30.4%, and 30.3% for the violet, blue, and green LEDs in the temperature range 300 K–400 K, while the reductions of internal quantum efficiency (η) with temperature are ~0.13, ~0.11, and ~0.1 respectively at the injection current density of 100 A cm−2. Moreover, two different slopes for all the η–T curves are observed: a lower absolute value of the slopes at T = 300–350 K; a larger absolute value of the slopes at T = 350–400 K. The numerical results also indicate that the efficiency droop effect with increasing the temperature becomes more serious, especially for the InGaN/GaN LED structures with the lower In-content.

Performance of electrokinetic stacking enhanced paper-based analytical device with smartphone for fast detection of fluorescent whitening agent

Quantification is a fundamental aspect of performance of an analytical system. Paper-based analytical device (PAD) as an on-site detection platform has drawn wide attention mainly due to its portability and cost effectiveness. In this work, a portable and low-cost PAD for online preconcentration and sensitive determination of fluorescent whitening agent (FWA) was demonstrated, which was consisted of ultra violet light-emitting diode (UV LED), macro-focusing lens, smartphone and miniaturized DC voltage source. Taking a widely used FWA component VBL as the analyte, the performance of the PAD enhanced with electrokinetic stacking (ES) and fluorescence imaging detection was systematically investigated. With ES, the sensitivity of the PAD system was 160-fold enhanced, and a limit of detection (LOD) of 0.06 μg mL−1 was achieved. The dynamic range was 0.1–10.0 μg mL−1 (linear in 0.1–0.7 μg mL−1, R2 = 0.99). With manual operation, the relative standard deviation (RSD) of intra-day and inter-day were all below 15%. Eventually, VBL from different napkin samples and toilet paper was determined with average recovery rates in the range of 90%–95% (RSD = 8.0%–12.0%). This work shows that with ES, the sensitivity of PAD can be greatly improved, and a LOD close to a desktop fluorescent spectrophotometer can be achieved as demonstrated by the detection of FWA component.

2D reduced graphene oxide–titania nanocomposites synthesized under different hydrothermal conditions for treatment of hazardous organic pollutants

Two-dimensional reduced graphene oxide–titania (RGO–TiO2) composites were prepared using a single-step hydrothermal method under various hydrothermal reaction conditions. The morphological and surface characteristics of the RGO–TiO2 composites and reference materials were determined. The RGO–TiO2 composites showed photocatalytic activity for the decomposition of two target pollutants that was superior to both pure TiO2 and RGO under fluorescent daylight lamp illumination. The photocatalytic activity of the RGO–TiO2 composite increased as the hydrothermal treatment time increased from 1 to 24h, but then it decreased as the time increased to 36h, which indicated the presence of an optimal treatment time. RGO–TiO2 composites activated by violet light-emitting diodes (LEDs) displayed lower decomposition efficiency than those activated by a daylight lamp, likely because of the lower light intensity of violet LEDs (0.2mW/cm2) when compared with that of the daylight lamp (1.4mW/cm2). However, the photocatalytic decomposition of the target pollutants using the RGO–TiO2 composite was more energy-efficient using the violet LEDs. The photocatalytic reaction rates increased as the residence time decreased, whereas the reverse was true for the decomposition efficiency.