Types Of Junctions Research Articles

Influence of heat-conducting elements on temperature amplitude of inner surface of frame-supporting buildings

The paper considers the heat stability of enclosing structures of frame-supporting buildings. These buildings are characterized by a significant heterogeneity of enclosing structures. The supporting structures have a large number of uprights, beams, lintels, connectors, and heat-conducting elements such as building corners, balconies, window and door jambs, and plinth nodes. Two typical junctions are considered for a frame-supporting building with light gauge steel framing and wooden frames. The Simulation module of the SolidWorks software is used to analyze the obtained minimum and maximum temperature on the inner surface. The diagram of the temperature distribution is suggested for two design solutions, i.e., the outer corner and floor junction, and the light gauge steel framing and wooden frame-supporting structure. It is found that near the heat-conducting elements, the maximum allowable value is exceed by 5 and 3 times for the light gauge steel and wooden framing respectively, which does not meet the standard requirements. The temperature fluctuations are observed in the junction between the floor and wall. Thus, for the light gauge steel framing, the temperature fluctuations occur at a distance of ~200 mm in the room, while in wooden-frame building, this distance is ~100 mm.

A broadband detector based on series YBCO grain boundary Josephson junctions.

Modeling of a broadband receiving system based on a meander series of Josephson YBaCuO grain boundary junctions integrated into a log-periodic antenna was carried out. The electromagnetic properties of the system, namely amplitude–frequency characteristic, beam pattern, and fraction of the absorbed power in each Josephson junction were investigated. Based on the obtained results, a numerical simulation of one-dimensional arrays was carried out. The dc characteristics of the detector were calculated, that is, current–voltage characteristic, responsivity, noise, and noise-equivalent power (NEP) for a 250 GHz external signal. The optimal number of junctions to obtain the minimum NEP was found. The use of a series of junctions allows one to increase the responsivity by a factor of 2.5, the NEP value by a factor of 1.5, and the power dynamic range by a factor of 5. For typical YBaCuO Josephson junctions fabricated on a ZrYO bicrystal substrate by magnetron deposition, the following parameters were obtained at a temperature of 77 K: responsivity = 9 kV/W; NEP = 3·10−13 W/Hz(1/2); power dynamic range = 1·106.

Steady state non-Newtonian flow in a thin tube structure: equation on the graph

The dimension reduction for the viscous flows in thin tube structures leads to equations on the graph for the macroscopic pressure with Kirchhoff type junction conditions at the vertices. Nonlinear equations on the graph generated by the non-Newtonian rheology are treated here. The existence and uniqueness of a solution of this problem is proved. This solution describes the leading term of an asymptotic analysis of the stationary non-Newtonian fluid motion in a thin tube structure with no-slip boundary condition on the lateral boundary.

Simulation of scanning near-field optical microscopy spectra of 1D plasmonic graphene junctions.

We present numerical simulations of scattering-type scanning near-field optical microscopy (s-SNOM) of 1D plasmonic graphene junctions. A comprehensive analysis of simulated s-SNOM spectra is performed for three types of junctions. We find conditions when the conventional interpretation of the plasmon reflection coefficients from s-SNOM measurements does not apply. Our approach can be used for other conducting 2D materials to provide a comprehensive understanding of the s-SNOM techniques for probing the local transport properties of 2D materials.

Anisotropic topological superconductivity in Josephson junctions

We investigate the effects of magnetic and crystalline anisotropies on the topological superconducting state of planar Josephson junctions (JJs). In junctions where only Rashba spin-orbit coupling (SOC) is present, the topological phase diagram is insensitive to the supercurrent direction, but exhibits a strong dependence on the magnetic field orientation. However, when both Rashba and Dresselhaus SOCs coexist, the topological phase diagram strongly depends on both the magnetic field and junction crystallographic orientations. We examine the impact of the magnetic and crystalline anisotropy on the current-phase relation (CPR), energy spectrum, and topological gap of phase-biased JJs, where the junction is connected in a loop and the superconducting phase difference is fixed by a loop-threading magnetic flux. The anisotropic CPR can be used to extract the ground-sate phase (i.e., the superconducting phase difference that minimizes the system free energy) behavior in phase-unbiased JJs with no magnetic flux. Under appropriate conditions, phase-unbiased JJs can self-tune into or out of the topological superconducting state by rotating the in-plane magnetic field. The magnetic field orientations at which topological transitions occur strongly depend on both the junction crystallographic orientation and the relative strength between Rashba and Dresselhaus SOCs. We find that for an optimal practical application, in which the junction exhibits topological superconductivity with a sizable topological gap, a careful balancing of the magnetic field direction, the junction crystallographic orientation, and the relative strengths of the Rashba and Dresselhaus SOCs is required. We discuss the considerations that must be undertaken to achieve this balancing for various junction types and parameters.

Low interfacial resistivity in CoSi2/ZrCoSb thermoelectric junctions

Both p-type and n-type MCoSb (M = Ti, Zr, Hf) half-Heusler compounds have been found to exhibit high thermoelectric performance for power generation, but there is still a lack of research on the suitable interfacial materials to connect both p-type and n-type MCoSb for device assembly. Here, CoSi2 was selected as the electrode to connect p-type Hf0.5Zr0.5CoSb0.8Sn0.2 and n-type (Hf0.6Zr0.4)0.88Nb0.12CoSb, and the interfacial microstructure and interfacial contact resistivity were studied before and after thermal aging. In both types of thermoelectric junctions, the interface layer with a thickness from several to tens of μm is formed, which ensures a good bonding strength. The interfacial contact resistivity of both as-sintered thermoelectric junctions was less than 1 μΩ cm2, which rises to 3–4 μΩ cm2 after aging for 8 days at 1,073 K and keeps almost unchanged during the longer aging treatment. The present work demonstrates that CoSi2 is a suitable electrode material for both p- and n-type MCoSb due to the good bonding strength and the low interfacial resistivity, which paves the way for the applications of MCoSb-based TE materials.

Dynamics Modeling and Vibration Analysis of Planar 3-RRR Flexible Parallel Robot

To address the issue of complicated dynamics modeling and difficult solution of 3-RRR flexible parallel robot, we propose a method of building a flexible parallel robot dynamics model using screw bond graph. Firstly, the structure of the flexible parallel robot is analyzed; secondly, the multi-energy domain dynamics model of the robot is built using screw bond graph and vector bond graph considering the elastomeric transformation in the middle flexible linkage; finally, based on the model, the closed-loop control strategy for suppressing harmful vibration of the system, and the speed loop error compensation for different control parameters is also studied. Author establishes the vector bond and spin bond conversion junction type based on the power conservation transfer principle, which realizes the combination of rigid and flexible system in this paper. And we construct the dynamical model of multi-energy domain flexible parallel robot system.

P194 A modified Rutgeerts score of i2a after ileocolic resection for Crohn’s Disease: endoscopic recurrence or anastomotic healing?

Abstract Background The reliability and reproducibility of scoring endoscopic recurrence is of utmost importance because it generally determines initiating postoperative medical therapy and it is used as outcome parameter in clinical trials. Variability in endoscopic scoring may result in inappropriate therapeutic decisions and study conclusions. It is hypothesised that different types of anastomoses have an influence on scoring endoscopic recurrence using the Rutgeerts’ score. The aim of this study is to analyse to what extent the ulcerations are determined by the type of anastomosis and how it interferes with the scoring of Crohn’s recurrence. Methods This is a retrospective review of endoscopy videos to re-assess endoscopic recurrence. All videotapes of the ileocolonoscopy were blinded and scored by a trained gastroenterologist (MD) and a surgeon (WB). Videos were excluded if the quality of the video was low or if the anastomosis was not visualised properly. The primary outcome is the presence of ulcerations six months after surgery, on individual parts of the anastomosis: inverting stapled anastomosis (side to side conjunction) and everting type of junction (transection ends). In the latter group, at least one site – colon, ileum or both – was scored. Results Of 99 available endoscopy videos, eighty-nine eligible patients were included in this retrospective study for analysis. The inverting and everting stapled anastomosis were scored individually using the SES-CD. A SES-CD of zero was found in 21/89 (23.6%) of the inverting anastomoses versus 74/75 (98.67%) in the everting anastomoses. Conclusion This study demonstrated a significant difference in wound healing of the inverting anastomosis versus the everting anastomosis. Inverting anastomoses show ulcerations and a circular scar long after surgery irrespective of the presence of ulcerations of terminal ileum. A normal wound healing phenomena might mistakenly be seen for recurrent Crohns’ disease. Everting anastomosis, on the contrary, heal without residue.

2D Bifurcation diagram of capacitively coupled Josephson junctions in high-Tc superconductors

We study the nonlinear dynamics in an array capacitively coupled Josephson junctions with N=3 junctions. We consider the superconductor/ insulator/ superconductor, SIS, type junctions as a model for high temperature superconductors with layered structure. In this study, we introduce the 2D bifurcation diagrams for the Josephson junctions. First we show a current voltage characteristics (CVC) of Intrinsic Josephson Junctions (IJJs) with N=3 Junctions, then we show the breakpoint region,BPR (a region in which a net electric charge appear on superconducting layers, (S-layers), of junctions), in the CVC of the system, then we try to investigate the chaos in BPR region by the 2D bifurcation diagram of the system. We show the 2D bifurcation diagrams in two cases in which either the coupling factor, α or the β parameter which is related to dissipation, be variable. In the later case we showed there is a range of β parameter in which the chaotic region of BPR is disappeared, also we show that there is another range of β in which the BPR structure disappeared.

Electronic structure of epitaxially grown and regrown GaN pn junctions characterized by scanning Kelvin probe and capacitance microscopy

Epitaxial regrowth of GaN pn junctions is a key technology for realization of a variety of high-performance GaN power electronic devices. However, the regrowth process can introduce impurities and defects that degrade a device’s performance. Here, we show that scanning Kelvin probe force microscopy and scanning capacitance microscopy can be used in a cross-sectional geometry to probe dopant distributions and an electronic structure in epitaxially grown GaN pn junctions. These measurements enable profiling of potential and dopant distributions across GaN pn junctions produced by uninterrupted epitaxial growth and by regrowth on an etched surface. Clear differences are observed in comparisons to the electronic structure of these two types of junctions that can be correlated with results of complementary characterization of dopant distributions reported for similarly grown structures. These measurements also suggest the presence of defects in etch-and-regrow pn junction structures that extend nearly 1 μm below the regrown interface.

Characterization of carrier transport using a bifacial structure for rational design of p-n junction PbS solar cells

In this study, a difference in the mobility of holes and electrons as a minority carrier has been systematically characterized in PbS quantum dot (QD) solar cells. While the mobility of electrons and holes is important in designing the p-n junction solar cells, it is still challenging to measure them during the normal operation of QD solar cells. When the solar includes only one transparent contact, it is difficult to separate the transport of electrons from that of holes during the normal operation of the device. We fabricated the bifacial solar cells and characterized the carrier transport by measuring the decay of photocurrent under pulsed illumination. The electron and hole mobility of p-type, n-type, and p-n junction type PbS QD film was examined and its connection to the performance of the solar cells was studied. In n-type PbS layer, the diffusion length of both electron and hole is ∼300 nm. In contrast, the diffusion length of hole and electron of p-type PbS layer is 250 nm and 175 nm. The asymmetric charge kinetics between holes and electrons in p-type PbS is systematically discussed. This result offers a rationale design rule of p-n junction type QD solar cells. 1) A difference in the mobility of holes and electrons is measured. 2) In n-type PbS layer, the diffusion length of both electron and hole is ∼300 nm 3) In p-type PbS, the asymmetric charge kinetics between holes and electrons is observed. 4) This study guides the design of the p-n junction type solar cells.

Conservation laws with discontinuous flux function on networks: a splitting algorithm

<abstract><p>In this article, we present an extension of the splitting algorithm proposed in [<xref ref-type="bibr" rid="b22">22</xref>] to networks of conservation laws with piecewise linear discontinuous flux functions in the unknown. We start with the discussion of a suitable Riemann solver at the junction and then describe a strategy how to use the splitting algorithm on the network. In particular, we focus on two types of junctions, i.e., junctions where the number of outgoing roads does not exceed the number of incoming roads (dispersing type) and junctions with two incoming and one outgoing road (merging type). Finally, numerical examples demonstrate the accuracy of the splitting algorithm by comparisons to the exact solution and other approaches used in the literature.</p></abstract>

Comparative Study of Y‐Junction Nanotubes with Vertex‐Edge Based Topological Descriptors

The current results of various forms of carbon nanostructures and its applications in different areas attract the researchers. In pharmaceutical, medicine, industry and electronic devices they used it by its graphical invariants. The detection of different types of carbon nanotubes junctions enhanced the attention and interest for forthcoming devices like transistors and amplifiers. A topological index plays a very important role in the study of physicochemical properties of biological and chemical structures. In this paper, we determine results of ve‐degree topological indices for various type of carbon nanotubes Y‐junctions and their comparisons. The particular indices called as The first ve‐degree Zagreb β index, the second ve‐degree Zagreb index, ve‐degree Randic index, ve‐degree atom‐bond connectivity index, ve‐degree geometric‐arithmetic index, ve‐degree harmonic index and ve‐degree sum‐connectivity index.

Analysis of unfavorable postoperative outcomes in patients with lumbosacral junction anomalies

The absence of a unified diagnostic approach and heterogeneous treatment strategies in patients with lumbosacral transitional vertebra contribute to registration of contradictory data on postoperative outcomes in these patients. A retrospective analysis of postoperative outcomes in patients with degenerative lumbar spine diseases associated with lumbosacral junction anomalies and causes of unfavorable results. Lumbosacral transitional vertebra was preoperatively verified and classified according to Castellvi A.E. in 352 cases between 2007 and 2017. Full-time examination, phone and e-mail survey covered 314 (89.2%) patients throughout 5.2-year follow-up period. There were unfavorable clinical outcomes in 42 cases. We analyzed the causes of these results and relationship of surgical strategy with the type of lumbosacral junction anomaly. Lumbosacral transitional vertebra Castellvi type IIA (30.9%) and IIIA (34.9%) prevailed. Unfavorable outcomes occurred in 7 cases after percutaneous interventions, in 12 patients after decompression surgery and in 23 patients after decompression and stabilization procedures. In all cases (n=42), redo surgery was performed: rigid fixation or extension of stabilization system in 16 cases, additional intracanal decompression in 10 patients, foraminal/extraforaminal decompression in 8 patients. Seven patients underwent repeated laser denervation. Of these, 5 patients underwent dorsal decompression without discectomy due to ineffective denervation. Correlation analysis showed the relationship between unfavorable outcomes after percutaneous procedures with LV transverse process dysplasia and sacralization, decompressive interventions with additional articular joints and lumbarization, decompression/stabilization procedures with LV transverse process dysplasia and sacralization. Unfavorable outcomes occurred after percutaneous interventions for anomaly type IB and IIIB, decompressive procedures for anomaly type IIA, IIB and IV, decompression/ stabilization procedures for types IA and IIIA. It is the first report devoted to analysis of relationships between unsatisfactory postoperative outcomes, surgical technique and type of lumbosacral dysgenesis.

The nature of metabolic processes in human dental hard tissues depending on their morphological structure

Was to give a comparative assessment of the movement of enamel and dentin fluid depending on the morphological structure of different sections of human dental hard tissues. The research involved 140 female subjects aged 21-30 years. Sizes, form, surface of enamel-dentin junction, enamel prisms and their crystals in superficial, middle and deep sections, width, tortuosity, facing of dentin tubules of tested teeth were analyzed by scanning electron microscope Jeol JCM-5700 and atomic force microscope NTEGRA Prima. The biochemical study examined the quantitative content of water in the samples of enamel, dentin, enamel-dentin junction by weighing sample weights before and after drying. The data obtained were processed by methods of variation statistics using standard packages Microsoft Excel 2008, Statistica 12.0. The enamel-dentine junction of large-fastened type is characterized by zones of dentin integration into enamel at the distance of more than 10 mm, with regular arrangement of enamel prisms and wide dentine tubules of 3.55 to 4.70 μm in diameter; no water content reduction was found. The small-fastened type has less pronounced spots of dentin interference with enamel from 2 to 10 μm, the dentinal tubules are slightly curved with a diameter of 2.90 to 3.60 μm, the water content in dentin is reduced. In microfastened type, a linear structure with interpenetration zones up to 2 μm, enamel prisms slightly ordered, dentin tubules narrowed and curved in diameter from 1.30 to 1.95 μm, water content in enamel and dentin is reduced. At microfastened type of enamel-dentin junction, chaotic arrangement of enamel prisms and narrow dentin tubules water movement is broken and metabolic processes are reduced that determines high probability of exposure of dental hard tissue diseases.

Temperature-dependent thermal transport of single molecular junctions from semiclassical Langevin molecular dynamics

Thermal conductance of single molecular junctions at room temperature has been measured recently using picowatt-resolution scanning probes. However, fully understanding thermal transport in a much wider temperature range is needed for the exploration of energy transfer at single-molecular limit and the development of single-molecular devices. Here, employing a semiclassical Langevin molecular dynamics method, a comparative study is performed on the thermal transport of an alkane chain between Au and graphene electrodes, respectively. We illustrate the different roles of quantum statistics and anharmonic interaction in the two types of junctions. For a graphene junction, quantum statistics is essential at room temperature, while the anharmonic interaction is negligible. For a Au junction, it is the other way. Our study paves the way for theoretically understanding thermal transport of realistic single-molecular junctions in the full temperature range by including both quantum statistics and anharmonic interaction within one theoretical framework.

Van der Waals Antiferroelectric Magnetic Tunnel Junction: A First-Principles Study of a CrSe2/CuInP2S6/CrSe2 Junction.

Magnetic tunnel junctions (MTJs), ferroelectric/antiferroelectric tunnel junctions (FTJs/AFTJs), and multiferroic tunnel junctions (MFTJs) have recently attracted significant interest for technological applications of nanoscale memory devices. Until now, most of them are based on perovskite oxide heterostructures with a relatively high resistance-area (RA) product and low resistance difference unfavorable for practical applications. The recent discovery of the two-dimensional (2D) van der Waals (vdW) ferroelectric (FE) and magnetic materials has opened a new route to realize tunnel junctions with high performance and atomic-scale dimensions. Here, using first-principles calculations, we propose a new type of 2D tunnel junction: an antiferroelectric magnetic tunnel junction (AFMTJ), which inherits the features of both MTJ and AFTJ. This AFMTJ is composed of monolayer CuInP2S6 (CIPS) sandwiched between 2D magnetic electrodes of CrSe2. The AFTJ with nonmagnetic electrodes of TiSe2 on both sides of CIPS and the asymmetric AFTJ with both CrSe2 and TiSe2 electrodes are also investigated. Based on quantum-mechanical modeling of the electronic transport, sizeable tunneling electroresistance effects and multiple nonvolatile resistance states are demonstrated. More importantly, a remarkably low RA product (less than 0.1 Ω·μm2) makes the proposed vdW AFMTJs superior to the conventional MFTJs in terms of their promising nonvolatile memory applications. Our calculations provide new guidance for the experiment and application of nanoscale memory devices.

Ureter-first Approach and Reduction of Pelvis: Standardizing Handling of Ureteropelvic Junction During Pyeloplasty

ObjectiveTo present our “ureter-first” approach as a standardized step-wise incision-making technique to deal with all types of uretero-pelvic junction (UPJ) anatomy during pyeloplasty. Pyeloplasty is a common surgery performed for UPJ obstruction, with Anderson-Hynes’ pyeloplasty being the commonest. However, there is great variability in handling UPJ and incision-making among the surgeons with no detailed standardized description that can be followed in all cases, notwithstanding broad descriptions of incision lines. We underscore this aspect of pyeloplasty and present our universal technique with a goal to minimize surgical errors. MethodsA standardized step-by-step handling of UPJ and sequential incision-making was developed for pyeloplasty. It avoids unwarranted loss of any pelvis tissue before confirming individual UPJ anatomy, emphasizes preservation of lower lip of pelvis and minimizes tension on anastomosis. This standardized technique was uniformly used in all cases over 5 years. The peri-operative and functional outcome results are presented. ResultsFifty-one consecutive cases were done using ureter-first approach. UPJ was >1 cm in eight cases. Three of these had UPJ >2 cm. Eight other cases had a low-insertion below level of kidney while three had high insertion of ureter. There were no cases which were deemed to be done under tension or unsatisfactory repair by the surgeon. There were no failures requiring any kind of redo repair at mean follow up of 39 months. ConclusionA uniform standardized approach saves the surgeon from unwarranted or wrongly designed incisions on the pelvis and thus has the potential to reduce surgical mistakes.

Roles of triple and quadruple junctions on plasticity by phase-field crystal approach

Roles of non-/symmetric triple and quadruple junctions on plasticity of ploycrystals are examined using phase-filed crystal model combined with an isovolumetric deformation technique. We designed four polycrystalline samples containing the four types of junctions respectively to simulate the deformation process under a strain rate comparable to practical situations. Our results uncover relationships between the ability of resistances to external deformations and the deformation mechanisms. For the ploycrystals containing quadruple junctions, the symmetric junction is beneficial to maintain the stability of the junctions during deformations, while asymmetric ones would be disjointed and result in formation and growth of sub-grains. For the polycrystals containing triple junctions, the stability of the junction is strongly related to the misorientation angles of the associated grains. The triple junction composed with high-angle GBs exhibits excellent stability under successive deformations and the deformation is dominated by GB migrations. Low-angle GBs migrate more easily than the high-angle ones.

Road Traffic Safety Analysis Of Different Junction Types On The State Roads

The highest number of road accidents occurs at junctions. One of the aims of traffic organisation is to improve traffic safety in these areas. Based on a variety of indices – road capacity, points of conflict, number, and severity of road traffic accidents – different alternatives for junctions are evaluated. However, the road network has many junctions and roads serve to travel from point "A" to point "B" at a given time. Therefore, one of the most important tasks when addressing the issue of road safety is to find a rational way of improving the safety without losing the importance of the road. The aim of this paper is to analyse the impact of different junctions on the road network and basing on actual data develop a method for the evaluation of different types of junctions with respect to road class.