Twinning-induced Plasticity Research Articles

Change in deformation mechanism to change TRIP to TWIP strengthening in the class of 304 austenitic stainless steel sheets by trapezoidal wavy-rolling process

ABSTRACT Strengthening of steels through twinning-induced plasticity (TWIP) has several advantages like high-strength and high-ductility combination over the transformation-induced plasticity (TRIP) mechanism which gives high strength, low ductility and product phase of martensite in the single phase solid solution of austenitic matrix. But, development of TWIP effect will be more difficult unless the steel contains high stacking fault energy (SFE) (>20mJ/M2), fine grain structure and high manganese alloying (15–30 wt.%). These are very expensive processes and susceptible to metallurgical complexity in the austenitic stainless steels. Therefore, new processing technology was developed for strengthening of the austenitic stainless steel sheets by trapezoidal wavy rolling (TWR). Type 304 austenitic stainless steel was selected for this study which is known as martensite transformation, a dominant hardening mechanism due to low SFE and coarse grained structure. Wavy deformation-induced results have been studied through strain hardening behaviour by flow stress-strain curves and microstructural changes by atomic force microscope (AFM), and phase transformations by using X-ray diffractometer (XRD) analysis. It is found that this process introduced changes from TRIP to TWIP mechanism by forming plenty of mechanical twins and shear bands type structure at initial stage of deformations and partial martensite is observed in advanced stage.

Enhanced yield stress and reduced elastic modulus of metastable β Ti–Nb alloys deformed by equal channel angular pressing attributed to the Synergistic effect of deformation mechanisms

This work aims to obtain Ti–Nb alloys with a high yield stress, good plasticity, and low elastic modulus. To this end, metastable β Ti–Nb alloys were subjected to multipass equal channel angular pressing (ECAP) deformation at room temperature, and a thorough investigation of their microstructure evolution, deformation mechanisms, and strengthening/toughening mechanisms was conducted through X-ray diffraction, transmission electron microscopy, electron backscatter diffraction, and tensile tests. In the initial deformation stages, multiple deformation mechanisms are observed, including dislocation slip, {332} <113> twinning, stress-induced martensite (SIM) α″-phase, {112} <111> twinning, and stress-induced ω-phase. However, as the strain accumulates, the ω-phase disappears, the volume fraction of the SIM α″-phase gradually decreases, and the dominant deformation mechanism changes to dislocation slip and {332} <113> twinning. The ECAP deformation results in a complex-network microstructure and the precipitation of the nanoscale SIM α″-phase, which leads to the twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP) effects. As a consequence, the Ti–Nb alloy simultaneously exhibits a high yield stress and a good plasticity. Furthermore, the high-density dislocations and interfaces generated by the ECAP deformation reduce the stability of the β-phase, and the introduced nanopores cause a decrease in density, resulting in a decrease in the elastic modulus of the alloy.

Enhanced strength–ductility synergy in Ti55531 titanium alloys through gradient microstructural design strategy

The strength-ductility trade-off dilemma still exists for titanium alloys, which is a challenging and pressing issue within the realm of microstructure design and property control. In the present work, a typical axial gradient microstructure was prepared in Ti55531 titanium alloy through a composite strengthening process involving rapid electropulsing treatment (EPT) combined with step-quench treatment (SQT). The results show that a significant improvement of 450 MPa (54 %) and 6.3 % (100 %) for the strength and ductility are obtained respectively for gradient microstructure by EPT + SQT (GMES) compared to that gradient microstructure prepared by EPT (GME) only. This indicates that the enhanced strength-ductility synergy observed in GMES is attributed to the characteristic Twinning induced Plasticity (TWIP) mechanism employed in this novel design of gradient microstructure. Furthermore, a detailed analysis and discussion are provided on the physical deformation mechanism and crack initiation behaviour of the gradient microstructure, providing valuable insights for the design of high-strength, high-ductility metals such as beta titanium alloys, advanced steels, and multi-phase alloys.

Hot Deformation Behavior and Dynamic Recrystallization Mechanism of Fe-18.2Mn-0.52C Twinning-Induced Plasticity Steel

Hot Deformation Behavior and Dynamic Recrystallization Mechanism of Fe-18.2Mn-0.52C Twinning-Induced Plasticity Steel

Designing the heterogeneous microstructure via a direct warm rolling process to synergistically enhance the strength-ductility in a medium Mn steel

This work introduced a facile method for fabricating heterostructures in a medium Mn steel via a direct warm rolling process. The heavy warm rolling promoted the transformation of metastable austenite (∼12.2 vol%) into hard domain α’ martensite, which formed a heterogeneous microstructure with the untransformed γ (soft domain). After 600 °C re-annealing, the hard domain α’ re-reversed to α + γ, and the heterostructure disappeared. Compared to the homogeneous structure, the heterostructure exhibited the synergistic enhancement of strength-ductility (yield strength (YS): 782 → 1113 MPa; ultimate tensile strength (UTS): 1099 → 1304 MPa; total elongation (TEL): 20.8 % → 21.7 %). Quantitative analysis showed that the heterogeneous deformation induced (HDI) strengthening (∼261 MPa) was the primary contributor to the increased ΔYS (782 → 1113 MPa) value, rather than the traditional strengthening mechanisms. Transformation induced plasticity (TRIP) and twinning induced plasticity (TWIP) effect were the main deformation mechanisms of both homogeneous/heterogeneous structures. However, compared to the homogeneous microstructure, the heterogeneous structure possessed the more pronounced TRIP and HDI hardening effects as well as L-C locks, the cooperative effect of these three factors further improved the strain hardening ability to break through the strength-ductility trade-off dilemma.

Effect of grain size and segregation on the cryogenic toughness mechanism in heat-affected zone of high manganese steel

High manganese steels have been nominated as desirable materials used for various cryogenic applications due to their excellent cryogenic toughness caused by twinning. High manganese steel welded joints were obtained through gas metal arc welding, and the microstructural differences at three subzones of heat-affected zone (HAZ) were utilized. The aim was to investigate the effect of grain size and Mn/C/Cu segregation on the cryogenic toughness mechanism of high manganese steel welded joints. The results indicate that the average impact absorbed energies at −196 °C for 1.0, 3.0, and 5.0 mm from the fusion line (denoted by FL + 1, FL + 3, and FL + 5) is 118.6 J, 102.4 J, and 117.2 J, respectively. Compared with base metal, the embrittlement occurred in HAZ. Large grains improve toughness, while small grain boundaries, segregation, and precipitation in HAZ deteriorate toughness. Larger grain size facilitates the primary twins with thinner inter-twin spacing and twin thickness, and the high density of these primary twins inhibits the activation of secondary twins. This, in turn, enhances cryogenic impact toughness. Although the stacking fault energy (SFE) throughout the welding joint lays within the range for the twinning-induced plasticity effect, the enrichment of Mn/C/Cu slightly increases the local SFE and critical resolved shear stress for twining within the segregation zone. This phenomenon makes the activation of primary twins more challenging. Furthermore, the C segregation at grain boundaries leads to the precipitation of fine Cr23C6 carbides. These carbides serve as crack initiation points during impact tests, contributing to degradation in cryogenic impact toughness.

Superior strength and wear resistance of mechanically deformed High-Mn TWIP steel

In the present study, the mechanical and wear behaviour of the surface-mechanically treated high-manganese (high-Mn) twinning-induced plasticity (TWIP) steel were investigated. The TWIP alloy was first designed and fabricated via surface-mechanical attrition treatment (SMAT) system and the mechanical properties including strength, wear behaviour as well as the microstructural evolution were thereafter determined. Transmission electron microscopy (TEM) characterization revealed a typical dislocation as a result of the surface treatment as well as the formation of twin layers with a reduced stacking fault energy (SFE). Due to the ultra-fine grain refinement caused by plastic deformation during surface treatment, a microhardness value of 489 HV can be obtained after treatment. Likewise, the yield strength of the high-Mn TWIP steel could be enhanced from 360 MPa to 813 MPa and a reduction in elongation to failure of about 20 % can be achieved. The wear test showed that the treated TWIP steel possessed a reduced friction coefficient and improved wear resistance at different testing loads, attributed to the nanoscale refinement of grains induced during treatment. The strength, hardness, and wear resistance of the fabricated TWIP alloy improves significantly, thanks to surface treatment by SMAT.

Cooperative roles of twinning, transformation and strain partitioning on the excellent cryogenic strength-toughness synergy of dual-heterogeneous metastable high entropy alloys

In a metastable Fe50Mn30Co10Cr10 high entropy alloy (HEA), a dual-heterogeneous structure, encompassing both grain size and dislocation heterogeneity, has been constructed to obtain excellent cryogenic mechanical performance by varying the annealing temperature (630 and 740 °C) following severe deformation. The HS-630 sample, consisting of recovered coarse-grains (CG), recrystallized fine-grains (FGs) and un-recrystallized ultrafine-grains (UFGs), possesses higher yield strength (YS) of ∼965 MPa, ultimate tensile strength (UTS) of ∼1680 MPa and uniform elongation (UEL) of ∼45 % when compared to the fully-recrystallized HS-740 sample at liquid nitrogen temperature (LNT). The difference in YS is primarily caused by the grain boundary and dislocation strengthening of UFGs, whereas the higher ductility of the HS-630 sample is associated with the hierarchical activation of transformation- and twinning-induced plasticity (TRIP and TWIP) effects, and compatible strain partitioning between heterogeneous domains. The dual-heterogeneity results in different critical stresses of ε-phase nucleation in heterogeneous domains, and promotes sustainable TRIP effect in CGs and the emergence of TWIP effect in UFGs with strain progressing. Moreover, the strain of the ductile transformed ε-phase is mainly accommodated by non-basal slip, which contributes to the strain hardening in the later deformation stage. Furthermore, the higher cryogenic impact toughness of the HS-630 sample can be attributed to the synergistic effects of the fracture mode, the transformation characteristics, and the heterogeneous strain partitioning.

Unveiling the Stacking Fault-Driven Phase Transition Delaying Cryogenic Fracture in Fe-Co-Cr-Ni-Mo-C-Based Medium-Entropy Alloy.

In this work, the tensile deformation mechanisms of the Fe55Co17.5Cr12.5Ni10Mo5-xCx-based medium-entropy alloy at room temperature (R.T.), 77 K, and 4.2 K are studied. The formation of micro-defects and martensitic transformation to delay the cryogenic fracture are observed. The results show that FeCoCrNiMo5-xCx-based alloys exhibit outstanding mechanical properties under cryogenic conditions. Under an R.T. condition, the primary contributing mechanism of strain hardening is twinning-induced plasticity (TWIP), whereas at 77 K and 4.2 K, the activation of martensitic transformation-induced plasticity (TRIP) becomes the main strengthening mechanism during cryogenic tensile deformation. Additionally, the carbide precipitation along with increased dislocation density can significantly improve yield and tensile strength. Furthermore, the marked reduction in stacking fault energy (SFE) at cryogenic temperatures can promote mechanisms such as twinning and martensitic transformations, which are pivotal for enhancing ductility under extreme conditions. The Mo4C1 alloy obtains the optimal strength-ductility combination at cryogenic-to-room temperatures. The tensile strength and elongation of the Mo4C1 alloy are 776 MPa and 50.5% at R.T., 1418 MPa and 71.2% in liquid nitrogen 77 K, 1670 MPa and 80.0% in liquid helium 4.2 K, respectively.

Thermodynamic Prediction and Experimental Verification of Transformation‐Induced Plasticity/Twinning‐Induced Plasticity Effects in Advanced Low‐C High‐Mn Steel at Different Deformation Temperatures

The effectiveness of transformation‐induced plasticity (TRIP)/twinning‐induced plasticity (TWIP) effects in Fe–0.06C–26Mn–3Si–3Al advanced ferrous alloy is analyzed over a wide temperature range of −40 to 200 °C. The specific deformation mechanisms in the steel are experimentally investigated and predicted using thermodynamic calculations of stacking fault energy (SFE). These predictions were correlated with the microstructure of the steel and its mechanical behavior. The study finds that applied thermodynamic models effectively predict the occurrence of TRIP/TWIP effects at different deformation temperatures, aligning well with experimental observations in terms of ε/α′ martensite formation, indicative of the TRIP mechanism. Some discrepancies in SFE results are observed at Mn contents significantly higher or lower than the nominal composition of steel.

High dislocation density TWIP steel with an excellent combination of strength and plasticity

After undergoing 75% hot deformation and 40% cold deformation, a variant of TWIP (Twin Induced Plasticity) steel with a composition of Fe–22Mn−2.7Al−0.95C−0.75Si (wt.%) was subjected to annealing at various temperatures (850 °C, 650 °C, 550 °C) for 20min. The recovery annealed C550 sample exhibited a yield strength of 1289.20 MPa, a tensile strength of 1442.29 MPa and an elongation of 30.78%. Characterization and comparison of the samples were conducted using XRD, SEM, EBSD, TEM and uniaxial tensile tests. The yield strength of the sample was assessed through different strengthening mechanisms to analysis the exceptional properties of the recovery annealed sample. Experimental findings indicate that the high-density dislocation and the refinement of slip bands in the recovery annealed C550 samples contribute to their superior performance compared to the partially and fully recrystallized samples.

Effects of cooling process on the microstructure and mechanical properties of a novel high-V high-Mn TWIP steel for cryogenic storage tank applications

In the present work, a novel high-V high-Mn twinning induced plasticity (TWIP) steel for cryogenic storage tank applications was developed. Furthermore, innovative two-stage cooling processes encompassing ultra-fast cooling and the subsequent furnace cooling were proposed. Effects of cooling process on the microstructure and mechanical properties of the experimental steel were investigated. It was observed that with the change in cooling process (the initial temperature of furnace cooling rised gradually), the dwell time of hot-rolled plates above 600 °C was extended. The extension in dwell time facilitated the precipitation of secondary phase particles, leading to the change in average diameter and volume fraction of secondary phase particles. The yield strength increased with the increasing initial temperature of furnace cooling due to the combined effect of small-sized secondary phase particles inside the grains and large-sized ones located at the grain boundaries. The occurrence of intergranular cracking, primarily caused by the presence of large-sized secondary phase particles at the grain boundaries, was the main factor responsible for the significant reduction in total elongation. The small-sized secondary phase particles inside the grains inhibited deformation twinning, while the large-sized ones at the grain boundaries weaken the binding force between grain boundaries, which ultimately resulted in a decrease in cryogenic impact toughness. The implementation of two-stage cooling processes effectively mitigated the trade-off between yield strength and cryogenic impact toughness, offering a novel approach and valuable insights for optimizing the strength and toughness characteristics of cryogenic high-Mn steels.

Microstructural mechanisms endowing high strength-ductility synergy in CoCrNi medium entropy alloy prepared by laser powder bed fusion

CoCrNi medium entropy alloy (MEA) exhibits significant potential as a structural component for engineering applications. However, the traditional processing methods for pursuing the superior mechanical properties of CoCrNi MEA are often time-consuming and inefficient. Laser powder bed fusion (LPBF) offers substantial processing flexibility without the need for complex secondary processing. In this study, we optimized the processing parameters for CoCrNi MEA through an orthogonal experimental design, achieving as-printed CoCrNi components with a relative density of up to 99.4 %. The microstructure of the as-printed CoCrNi revealed hierarchical features, including the molten pools, equiaxed and elongated columnar grains, sub-grain cellular microstructures, and high-density dislocation networks. The mechanical properties of as-printed CoCrNi were exceptional, demonstrating a synergistic combination of strength and ductility (yield strength: approximately 660.91 MPa, tensile strength: approximately 892.78 MPa, elongation: approximately 33.28 %, and a product of strength and elongation: 27.45 GPa %). Experimental characterization elucidated the activation and interplay of mechanisms such as dislocations, stacking faults, twinning-induced plasticity, and transformation-induced plasticity. These mechanisms collaboratively enhanced the refinement and heterogeneity of substructures, thereby endowing the as-printed CoCrNi with significant strength-ductility synergy. Molecular dynamics simulations indicated that, in the initial stages of plastic deformation, a significant activation of Shockley partial dislocations occurred, leading to the formation of stacking faults and the emergence of Hexagonal Close-Packed (HCP) phases. As plastic deformation progressed, a reverse phase transformation from HCP to Face-Centered Cubic (FCC) took place, resulting in the formation of nanotwins. This transformation generated a heterogeneous microstructure comprised of both nanotwins and HCP phases, suggesting a sequential twinning and phase transformation pathway in as-printed CoCrNi: from FCC to HCP, and subsequently to FCC nanotwins.

Impact Toughness Dependent on Annealing Temperatures in 0.16C-6.5Mn Forged Steel for Flywheel Rotors

For the application of forged medium-Mn steels on flywheel rotors, the effect of annealing temperatures from 300 °C to 650 °C on the impact toughness of 0.16C-6.5Mn forged steel was investigated to demonstrate the microstructural characteristics and austenite reverse transformation determining the impact toughness. The results obtained through standard Charpy V-notch impact tests at ambient temperature show that the impact absorbed energy holds at lower than 10 J almost constantly at annealing temperatures of 300 °C to 500 °C, and a representative intergranular fracture is presented. At an annealing temperature of 600 °C, the impact absorbed energy increases to 147 J, with the ductile fracture characteristics showing plenty of fine dimples, and the high impact toughness is attributed to the high volume fraction above 30% and the moderate stability of reverted austenite. Subsequently, the annealing temperature rises higher than 600 °C, the impact absorbed energy decreases, and the fracture morphology shows brittleness characterized by more flat facets of intergranular fractures and small quasi-cleavage facets, presumably corresponding to the insufficient transformation and twinning-induced plasticity effect due to weakening the Mn partitioning from quenched martensite to reverted austenite, which results in lower austenitic stability. Furthermore, the ductile-to-brittle transition temperature (DBTT) of the 0.16C-6.5Mn forged steel annealed at 600 °C, which holds the highest impact absorbed energy, and is explored for the possibility of flywheel rotor application in a service environment. The DBTT reaches −21 °C, obtained through the Boltzmann function, and the impact absorbed energy is approximately 72 J.

Achieving ultrahigh strength and ductility via high-density nanoprecipitates triggering multiple deformation mechanisms in a dual-aging high-entropy alloy with precold deformation

How to achieve high-entropy alloys (HEAs) with ultrahigh strength and ductility is a challenging issue. Precipitation strengthening is one of the methods to significantly enhance strength, but unfortunately, ductility will be lost. To overcome the strength–ductility trade-off, the strategy of this study is to induce the formation of high-density nanoprecipitates through dual aging (DA), triggering multiple deformation mechanisms, to obtain HEAs with ultrahigh strength and ductility. First, the effect of precold deformation on precipitation behavior was studied using Ni35(CoFe)55V5Nb5 (at.%) HEA as the object. The results reveal that the activation energy of recrystallization is 112.2 kJ/mol. As the precold-deformation amount increases from 15 % to 65 %, the activation energy of precipitation gradually decreases from 178.8 to 159.7 kJ/mol. The precipitation time shortens, the size of the nanoprecipitate decreases, and the density increases. Subsequently, the thermal treatment parameters were optimized, and the DA process was customized based on the effect of precold deformation on precipitation behavior. High-density L12 nanoprecipitates (∼3.21 × 1025 m−3) were induced in the 65 % precold-deformed HEA, which led to the simultaneous formation of twins and stacking fault (SF) networks during deformation. The yield strength (YS), ultimate tensile strength, and ductility of the DA-HEA are ∼2.0 GPa, ∼2.2 GPa, and ∼12.3 %, respectively. Compared with the solid solution HEA, the YS of the DA-HEA increased by 1,657 MPa, possessing an astonishing increase of ∼440 %. The high YS stems from the precipitation strengthening contributed by the L12 nanoprecipitates and the dislocation strengthening contributed by precold deformation. The synergistically enhanced ductility stems from the high strain-hardening ability under the dual support of twinning-induced plasticity and SF-induced plasticity.

Discovery of microsegregation-aided transformation and twinning-induced plasticity in low Mn steel through directed energy deposition of functionally graded materials

Functionally graded materials (FGMs) combining two dissimilar steels, stainless steel 316 L and high-strength low-alloy steel, were additively manufactured using directed energy deposition. High-throughput characterization of the dissimilar steel FGM led to the discovery of a low Manganese (Mn<1 wt.%) TRIP (transformation-induced plasticity) and TWIP (twinning-induced plasticity) steel with a metastable microstructure enabled by additive manufacturing. Microsegregation from non-equilibrium solidification caused phase stability and stacking fault energy heterogeneity, leading to TRIP and TWIP effects in the as-built condition without heat treatment. Tensile testing of the new as-built TRIP and TWIP steel resulted in ultimate tensile strength of 960 MPa, yield strength of 415 MPa, total elongation of 26 %, and a unique strain hardening rate that increases after yielding. We compare experimental measurements of microsegregation with thermodynamic modeling to discuss the impact of microsegregation on phase stability, stacking fault energy, and solidification cracking susceptibility in additively manufactured FGMs. The highlights of this work include the discovery of a novel pathway for achieving TRIP and TWIP effects in additively manufactured steels without heat treatment. This work also shows that the TWIP effect can be introduced without high Manganese content playing a critical role in adjusting stacking fault energy.

Triplex steel powder design to avoid hot cracking in laser-powder bed fusion using computational thermodynamics

High manganese steels offer exceptional combinations of high strength and ductility, resulting in weight reduction when utilized in structural applications. Nevertheless, the conventional manufacturing routes of these steels is hindered by many production problems. Additive Manufacturing (AM) has emerged as a reliable solution to fabricate thin or complex shape compounds using these steel grades. Indeed, several studies have demonstrated the success to fabricate high manganese twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP) steels by laser-powder bed fusion (L-PBF). However, a recent study on a high manganese triplex steel composition has revealed the occurrence of both hot cracking and micro segregation during rapid solidification in L-PBF, highlighting potential processability issues of this family of high alloy steels. In this study, the hot cracking susceptibility of different triplex steels is evaluated, focusing on the impact of the composition on the solidification paths and final microstructures. A Computer Coupling of Phase Diagrams and Thermochemistry (CALPHAD) approach is employed to predict alloy-dependent hot cracking susceptibility so as to establish guidelines for preventing hot cracking and provide insights into alloy design for AM. Microstructural observations are used to determine the accuracy of CALPHAD predictions in terms of elemental segregation, phase formation and hot cracking susceptibility. To this end, scanning transmission electron microscopy is used to evaluate elemental segregation at grain boundaries, while the local distribution of phases and their relative amount is measured by electron backscattered and X-ray diffraction, respectively. Hot cracking susceptibility is experimentally evaluated by measuring the length of cracks (when present) in the cross section of printed specimens.

Effect of Al on the low cycle fatigue deformation behavior and microstructure evolution of Fe–22Mn-0.6C TWIP steel

The dependence of low cycle fatigue (LCF) behavior and microstructure evolution of Fe–22Mn-0.6C twinning-induced plasticity (TWIP) steel on the alloying element Al has been investigated under fully reversed total strain amplitude control with a nominal strain rate of 0.006 s−1 and strain amplitudes ranging from 0.002 to 0.010 at room temperature. The results indicate a strong dependence of LCF response and evolved microstructure on the addition of Al, owing to its effect on the stacking fault energy (SFE). At all strain amplitudes, the 3Al steel with a higher SFE exhibits a visibly lower cyclic hardening and a higher cyclic softening, resulting in a lower cyclic yield strength than the 0Al steel. As compared with the 0Al steel, the relatively higher SFE of the 3Al steel causes higher accumulated plastic strain, decreased slip planarity and weaker reversibility of dislocations, thereby decreasing the fatigue life. The optical microstructure is featured by increase in slip band density with increasing strain amplitude for both steels. However, the slip band density of the 3Al steel is higher than that of the 0Al steel. Moreover, cyclic loading promotes the formation of dislocation cells, rough labyrinths as well as planar dislocation arrays. Deformation twins are observed only in the 0Al steel with a visible lower critical twinning stress due to its low SFE as compared to the 3Al steel.

The {332} Twinning Behavior of a Ti-15Mo Medical Alloy during Cyclic Deformation and Its Effect on Microstructure and Performance.

In this study, the microstructural evolution of a Ti-15Mo medical alloy was investigated, when the in situ cyclic tensile strain had 2% amplitude and the tension-compression cyclic deformation had 1%, 2%, and 3% amplitude. The Vickers hardness and wear resistance of the alloy were also optimized due to the grain-refining effect after cyclic deformation and annealing. The twinning-induced plasticity (TWIP) was considered the main deformation mechanism of the Ti-15Mo alloy during the tensile-compressive cycle deformation with suitable strain amplitude. The {332}<113> twins and boundaries were the main contributors to the grain refinement. The optimal microstructure, hardness, and wear resistance were obtained in the alloy deformed by tension-compression cyclic strain with a 3% strain amplitude. The wear resistance of the annealed alloy in Hank's solution was excellent in contrast to the original Ti-15Mo alloy due to its reasonable microstructure and hardness. It is clear that abundant twins were formed and retained in the coarse grains of the original alloy after cyclic deformation and annealing, which provided the expected refined grains and performance.

Strain-induced solid-state coating of TWIP steel sheets with zinc

We propose the strain-induced solid-state coating process of twinning-induced plasticity (TWIP) steel with zinc, achieved through concurrent rolling of TWIP steel and zinc sheets. Our study explores the effects of strain, strain rate, and rolling temperature on the morphology and intermixing at the Zn-TWIP steel interface. We found that two simultaneous mechanisms are responsible for the formation of a joint interface between the sheets in the rolling temperature range of 100–380 °C, namely mechanical intermixing at the interface and accelerated diffusion along moving dislocations and other defects introduced during rolling. Since it is impossible to deconvolute these mechanisms, we introduced the concept of an ‘apparent diffusion coefficient’ to represent the diffusion-like mass transfer resulting from mechanical intermixing and diffusion. These diffusion coefficients were determined by primary electron energy variation method in scanning electron microscope and by energy-dispersive X-ray spectroscopy in transmission electron microscope. Notably, these diffusion coefficients were found to be higher than the grain boundary diffusion coefficients of Zn in γ-Fe, primarily due to the dynamic nature of interface microstructure formation during rolling.