Trough Solar Concentrator Research Articles

THEORETICAL PERFORMANCE ASSESSMENT OF A PARABOLIC TROUGH HUMIDIFYING SOLAR COLLECTOR-BASED SOLAR STILL

In this paper, a parabolic trough humidifying solar collector-based solar still (PHSC-SS) is proposed. Its purpose is to apply some important performance improvement techniques to the flat plate humidifying solar collector-based solar still (flat plate HSC-SS), to significantly improve overall system performance. These included the use of parabolic trough solar concentrators and the design of humidifying solar collectors from evacuated tube collectors. The results reveal that, unlike flat plate HSC-SS, which must operate with a turbulent airflow regime to achieve optimum overall performance, PHSC-SS must operate with a laminar airflow regime and high inlet and outlet temperatures of air (at least 55 °C and less than 100 °C, at atmospheric pressure) in the heat collector element. For 900 W/m2 of incident solar irradiance, 2 m2 of solar collector area, and 0,00042 kg/s of air flow rate, the maximum energy efficiency, exergy efficiency and daily freshwater productivity of PHSC-SS were found to be 68,12%, 14,87% and 1,697 kg/h, respectively. Whereas for the same incident solar irradiance and solar collector area, and 0,1 kg/s of air flow rate, those of the flat plat HSC-SS were 72,9%, 1,12%, and between 1,07 – 2,923 kg/h (for inlet and outlet temperatures of air less than 30 °C, at atmospheric pressure), respectively. Although in some extreme cases freshwater productivity of flat plate HSC-SS can be higher than that of PHSC-SS, it should be noted that laminar airflow regime confers great advantages to PHSC-SS. These are higher air temperatures at condenser inlet (which ease water condensation process), no need of an auxiliary cooling device (needed in the flat plate HSC-SS), less mechanical vibrations of system, reduced condenser size, and less energy consumed by air blowers. Furthermore, the upper limit of the PHSC-SS is a PHSC-SS that operates without air flow, but rather by vaporization of water droplets at boiling point from absorber, followed by their suction to condenser, similarly to a flash evaporation.

Sensitivity analysis of the thermal performance of a parabolic trough concentrator using Al2O3 and SiO2/Vegetable oil as heat transfer fluid

This paper aims to highlight the use of different heat transfer fluid (HTF) configurations based on vegetable oils in Parabolic Trough Solar Concentrator (PTSC). Rapeseed and jatropha oils as innovative heat transfer materials combined with SiO2 and Al2O3 to obtain six (6) HTF configurations are used in a 1-dimensional PTSC model. The thermophysical properties of the nanofluids are determined from correlations derived from the literature, using Gauss-Seidel method from a numerical code developed in Matlab software. Model validation is obtained. Thermal sensitivity analysis shows that the use of rapeseed increases the thermal efficiency of the PTSC by around 4.21 % compared with jatropha. The use of nanofluids reduces thermal losses within the system due to thermal gradients. For a fixed irradiance and each 1 %–4 % increase in volume fraction, thermal efficiency increases by around 1.96 % when Al2O3/rapeseed is used and by 0.47 % when SiO2/rapeseed is used compared with rapeseed. Similarly, thermal efficiency increases by around 1.98 % when Al2O3/jatropha is used and decreases by around 0.20 % when SiO2/jatropha is used compared with jatropha. However, the positive effects of nanoparticles on thermal conductivity alone are not always sufficient to improve thermal efficiency, and thermal effects on heat capacity should also be considered.

Study on the influence of dust accumulation on the optical performance of trough solar concentrator under different rainfall intensities based on alpine areas

Aiming at the typical characteristics of natural rainfall in alpine areas and the structure of the concentrator surface, based on the design scheme of the trough system test platform, the optical performance and cleaning characteristics of the mirror with rainfall intensity and concentrator tilt angle as variables are studied experimentally. The results show that small-scale rainfall has a critical tilt angle of positive and negative cleaning effect on transverse region1. Lower than this tilt angle causes pollution to the mirror surface. Rainfall above medium intensity has a positive cleaning effect on all mirror regions. The cleaning ability is the highest under the rainfall of 60° tilt angle of 38.9 mm. The bottom-up enhanced cleaning law in the transverse region is more significant under high-intensity rainfall, and the concentrator tilt angle is more sensitive to dust desorption than rainfall intensity. The average relative error and average root mean square error of the predicted reflectivity of the global mirror are 3.82% and 0.061 respectively, and the fitting accuracy is high. It provides theoretical guidance for the application of dust removal schemes and prediction of the optical performance of trough solar system in alpine areas.

Assessment of a parabolic trough solar thermal concentrator under two-phase flow conditions

In the present work, a mathematical model is developed to describe the heat, mass, and momentum transfer of a biphasic flow during its trajectory in the absorber tube of a parabolic trough solar concentrator (PTSC) for thermal processes in a transitory simulation, showing the evolution of the parameters in a dynamic system. The working fluid is water. The numerical solution of the model is implemented in C++ code. The model is validated with the results obtained from the DISS Project experiment. The results of the numerical solution have a maximum variation in the fluid temperature profile of 6.45 % and a maximum difference of 2.02 % in the outlet pressure of the fluid with respect to the experimental results. The case study consists of the analysis of a PTSC under different radiation conditions from two different cities in Mexico, Piedras Negras and Mexico City, on an average spring day. The results obtained allow us to analyze the behavior of the fluid temperature, the quality of the steam, and pressure drop through the absorber tube and time; under the conditions studied, the concentrator reached an efficiency of 52 %. It is observed that the model is sensitive to changes in climate.

Experimental Investigation of An Industrial Wastewater Treatment Unit Using Multi Filter Hybrid with Parabolic Trough Solar Concentrator

Experimental Investigation of An Industrial Wastewater Treatment Unit Using Multi Filter Hybrid with Parabolic Trough Solar Concentrator

Performance efficiency effectiveness of incidence angle of concave trough solar concentrator

Performance efficiency effectiveness of incidence angle of concave trough solar concentrator

Internally shielded receivers for parabolic trough solar concentrators operating with supercritical carbon dioxide: Analytical assessment

An urgent need to enable the operation of parabolic trough concentrators at higher temperatures for higher efficiency of the coupled power cycles is manifested in the state-of-art literature. Supercritical carbon dioxide is a promising fluid for the next generation of these concentrators. However, the inflated radiative thermal losses at elevated temperatures are the main challenge, and the relatively large absorber diameters are questionable for supercritical pressures. This study proposes a novel 1-D analytical model, coupled with Monte Carlo ray tracing, for evaluating internally shielded receivers based on the absorber tube’s diameter and eccentricity, the heat shield’s opening angle, as well as the operating conditions. The results suggest that increasing the tube diameter reduces the performance dependency on tube eccentricity, but also reduces the optical performance. Shielding the receiver is favorable for opening angles up to 160°. The impact of operating pressure is marginal, compared to flow rate and temperature. A shielded receiver with an opening angle of 160°, eccentricity of −10 mm, and tube diameter of 50 mm maximizes the exergy efficiency up to 45.9%, whereas a receiver with corresponding values of 80°, −15 mm, and 80 mm, respectively, maximizes the energy efficiency up to 77.2%. Shielded receivers also boost the efficiency by up to 10.6%, compared to conventional 70 mm receivers. These performance enhancements are expected to elevate the efficiency of the integrated systems with minimal economic and environmental impacts due to the simplicity of the proposed solution.

Performance Simulation of Solar Trough Concentrators: Optical and Thermal Comparisons

The solar trough concentrator is used to increase the solar radiation intensity on absorbers for water heating, desalination, or power generation purposes. In this study, optical performances of four solar trough concentrators, viz. the parabolic trough concentrator (PTC), the compound parabolic concentrator (CPC), the surface uniform concentrator (SUC), and the trapezoid trough concentrator (TTC), are simulated using the Monte Carlo Ray Tracing method. Mathematical models for the solar trough concentrators are first established. The solar radiation distributions on their receivers are then simulated. The solar water heating performances using the solar trough concentrators are finally compared. The results show that, as a high-concentration ratio concentrator, the PTC can achieve the highest heat flux, but suffers from the worst uniformity on the absorber, which is only 0.32%. The CPC can generate the highest heat flux among the rest three low-concentration ratio solar trough concentrators. Compared with the PTC and the CPC, the TTC has better uniformity, but its light-receiving ratio is only 70%. The SUC is beneficial for its highest uniformity of 87.38%. Thermal analysis results show that the water temperatures inside the solar trough concentrators are directly proportional to their wall temperature, with the highest temperature rise in the PTC and the smallest temperature rise in the TTC. The solar trough concentrators’ thermal deformations are positively correlated to their wall temperatures. The radial deformation of the SUC is much larger than those of other solar trough concentrators. The smallest equivalent stress is found in the SUC, which is beneficial to the long-term operation of the solar water heating system.

Trough-Type Free-Form Secondary Solar Concentrator for CPV/T Application

Imaging concentrators like the parabolic trough solar concentrators have been widely employed for energy production in solar power plants. The conventional imaging solar concentrators form a non-uniform Gaussian distribution on receiving absorbers yielding the highest temperatures. The traditional CSP system normally truncated a peripheral region of heat flux to better use the central part. CPV/T systems using the waste heat recovery method can largely improve the total efficiency. However, for the CPV module, the coolant temperature was usually below 80 °C, which limited the applications of the thermal cycle such as the ORC system. In this article, a novel trough-type free-form secondary solar concentrator (TFSC) for PV/Thermal hybrid application has been proposed. Different from other CPV/T concepts using a combined PV panel and cooling tunnel/tube, the current concept separates the receiver in two parts. The secondary free-form reflector is generated by the geometric construction method, resulting in uniform heat flux in the edge region and high concentration in the central region. Through the ray tracing method, the optical properties have been verified. Sensitivity analysis of the concentrating structure is also conducted. The results provide supports for the design and applications of novel CPV/T systems.

Concentration ratio for a solar trough concentrator with circular mirror and flat receiver

We present a simple analytical formula for the geometric concentration ratio of a circular trough optical concentrator coupled to a flat (planar) receiver. The receiver is sized to achieve full collection (no spillage) for any combination of acceptance and rim angle. The development reveals the existence of two concentration ratio regimes, one controlled by the edge ray caustics, and the other controlled by the intersection of the edge rays from the rim alone. Notably, we show that in the latter rim ray regime, the circular trough achieves the exact same geometric concentration ratio as a parabolic trough. The provided formula fills a gap towards the development of a complete catalogue of concentration ratio formulas for different concentrator/receiver geometries.

Impact of the Thermophysical Properties of a Cuo-H<sub>2</sub>O-Based Nanofluid on the Performance of a Cylindrical Solar Concentrator

Sustainability in energy production, energy security, and global warming are major concerns facing the globe today. Cylindrical Solar Concentrator is extensively utilized for technologically advanced processes, heat, and power plant applications by utilizing daylight sunshine at no running cost. Numerous inputs and characteristics impact the concentrator's performance, with the type of heat transfer fluid and its mass flow rate being two of the most important. This paper gives a numerical investigation of the influence of thermo-physical attribute of CuO water-based nanofluids on the effectiveness of the Parabolic Trough Solar Concentrator in Ogbomosho weather condition (lat. 8o011, long. 4o111).The governing equations of nanofluids with laminar flow and steady state, using iterative relaxation techniques, as well as the efficiency of the concentrator, were solved. A C++ simulation program was developed to investigate the impacts of thermo physical parameters on concentrator efficiency, with nanoparticle sizes ranging from 1 to 10 percent and mass flow rates of 0.1 kg/s, 0.15 kg/s, and 0.2 kg/s, at a constant incident solar insolation flux of 186 W/m2. The results demonstrated that increasing the mass flow rate of the nanofluids improves the heat transmission properties. The thermo physical properties of CuO-based nanofluids and its effects on the performance of the solar parabolic trough collector are being examined. The impact of thermophysical attributes on thermal effectiveness results in improved thermal efficacy, heat transfer characteristics of nanofluids, and factors influencing its features in solar collectors, which determines its usability. The Parabolic Trough Collector system based on nanofluids is a promising technology with applications in green surroundings.

Thermal-Optical Evaluation of an Optimized Trough Solar Concentrator for an Advanced Solar-Tracking Application Using Shape Memory Alloy.

One of the modern methods for enhancing the efficiency of photovoltaic (PV) systems is implementing a solar tracking mechanism in order to redirect PV modules toward the sun throughout the day. However, the use of solar trackers increases the system’s electrical consumption, hindering its net generated energy. In this study, a novel self-tracking solar-driven PV system is proposed. The smart solar-driven thermomechanical actuator takes advantage of a solar heat collector (SHC) device, in the form of a parabolic trough solar concentrator (PTC), and smart shape memory alloy (SMA) to produce effective mechanical energy for solar tracking applications from sun rays. Furthermore, a thermal–optical analysis is presented to evaluate the performance of the solar concentrator for the simulated weather condition of Dammam City, Saudi Arabia. The numerical results of the thermal and optical analyses show the promising feasibility of the proposed system in which SMA springs with an activation temperature between 31.09 °C and 45.15 °C can be utilized for the self-tracking operations. The work presented adds to the body of knowledge an advanced SMA-based SHC device for solar-based self-actuation systems, which enables further expansions within modern and advanced solar thermal applications.

Highly Concentrated Solar Flux of Large Fresnel Lens Using CCD Camera-Based Method

Fresnel lens is a kind of lens that can concentrate sunlight up to a level of thousands of suns with small space occupation which is widely used in the research of sunlight concentration and transmission systems via optical fiber. Most studies on the concentrated flux of lenses use experimental methods to measure the flux distribution on the receiver of parabolic trough solar concentrators, solar power towers, and parabolic dish concentrators, while for Fresnel lenses, especially large-aperture Fresnel lenses such as the one in this manuscript, the simulation approach was mostly used. In response to this problem, this study has developed an experimental system for measuring the concentrated flux density of Fresnel lenses. A charge-coupled device (CCD) camera was used to capture the image of spot of large-aperture (968 mm) Fresnel lenses in the CCD camera-based method, and a heat flow meter was used to calibrate the spot brightness image obtained by the CCD camera. Experimental data show that the peak flux of concentrated spot can reach 4.06 MW/m2. This method confirms the simulation results of previous studies that using the rays tracing method, that is, the flux level of the Fresnel lenses can reach 5000 suns. The experimental results demonstrated the CCD camera-based method combined with a heat flow meter is competent in measuring the intensity of flux with a level of 5000 suns.

Influence of sunshape and optical error on spillover of concentrated flux in solar thermal power tower plant

It is important to calculate and evaluate the spillover of flux reflected by heliostats on the heat shields for the construction, operation and optimization of solar thermal power tower plant. By establishing a concentrated flux distribution model of power tower plant based on the real sunshape and taking haze, optical error, shadowing and blocking effect into consideration, the authors calculated the flux density distribution on the receiver and heat shields under various conditions. The results show that the radiation energy on heat shields can reach about 15–45 MW under typical conditions, accounting for 1%–8% of the total received energy of the system. The flux density on heat shields is between 30 and 70 kW/m2, which is equivalent to the flux level of trough solar concentrator system. The calculations and fitting results show that the energy proportion on heat shields is positively correlated with circumsolar ratio(CSR) and optical error. The effect of CSR on the energy proportion of heat shields is linearly increasing, while the effect of optical error is nonlinear. This indicates that the spillover flux on heat shields can compensate for the loss of the receiver caused by haze, optical errors of heliostats.

Performance Optimization of Solar Photovoltaic System using Parabolic Trough and Fresnel Mirror Solar Concentrator

An attempt has been taken to design parabolic trough and Fresnel mirror solar concentrator with the purpose of optimizing the output power of a photovoltaic system for both bright sunny day and cloudy day by using a 72-cell 5W photovoltaic solar panel. The PV system's efficiency has been analyzed in terms of output voltage, current, and power of the solar panel. Accordingly, to our expectation, we observed that on a bright sunny day, the output power improvement of the solar panel is 26.81% for the parabolic trough and 17.89% for the Fresnel mirror concentrator. On a cloudy day, both concentrators improve output power by 22.3% and 14.1%, respectively. In terms of power optimization of a photovoltaic system, the following has been discerned: a solar photovoltaic concentrator system with a parabolic trough is much more effective than one with a Fresnel mirror.

Focusing Characteristics of Solar Trough Concentrator Based on Parabolic Mirror Rotating Array with Same Parameters

Focusing Characteristics of Solar Trough Concentrator Based on Parabolic Mirror Rotating Array with Same Parameters

Design and Evaluation of Polygonal Trough Solar Concentrator

In this paper, a solar concentrator is designed in the form of a concave half-cylindrical mirror consisting of polygonal reflective surface plates. The plates are arranged to give a hemispherical shape to the design. These surfaces work to receive solar radiation and focusing by reflecting it to the receiver that is placed in front of the reflecting surfaces. The results are compared with a system consisting of a concave reflecting surface of the same dimensions to obtain a good criterion for evaluating the design performance. The results showed a low acceptance angle for the design for all the samples used due to the geometrical design nature. The optical efficiency affected by the angle of incidence greatly by all the samples used, which differ in the concentration ratio, width and location of the receiver.

Optimization of thermal efficiency on solar parabolic collectors using phase change materials - experimental and numerical study.

Solar energy is a one-of-a-kind renewable energy source that has many uses, and in the thermal applications, it is receiving more attention and is becoming more feasible. The present work presents numerical and experimental studies to investigate the performance of a parabolic trough solar concentrator (PTC) integrated with a thermal energy storage system. A new receiver design is built that stores thermal energy using phase change material (PCM). A concentric absorber tube with two different kinds of PCM - MgCl2·6H2O and erythritol (filling the annular-space of absorber tube) - were used to construct a PTC, and its thermal performance and thermal efficiency were investigated under two different HTF flow rates of 0.005 kg/s and 0.033 kg/s. Solar energy is transformed into heat, which is then used to store in the PCM before being discharged to cold water, which is the final heat transfer fluid in the receiver's inner pipe. The simultaneous studies of the PTC with and without PCM are investigated. A commercial Mat Lab's operating model through an imperialist competitive algorithm of the entire PTC system is presented, and the numerical results were compared to the experimental results, which were carried out with and without PCM in PTC. With the PCM in PTC (0.005 kg/s and 0.033kg/s), the HTF exhibited gain in peak temperatures of 11°C (erythritol) and 9°C (MgCl2·6H2O) at 0.05 kg/s, whereas the peak temperatures further increase to 14°C (erythritol) and 12°C (MgCl2·6H2O) respectively at 0.033 kg/s, as compared to HTF without PCM. Average thermal efficiency of PTC with HTF flow rate of 0.033 kg/s was highest with usage of erythritol (40.6%), among all the cases. The experimental and predicted thermal efficiency performance indices for different flow rates and PCM are found to be with a deviation of around ± 1.9%, demonstrating the accuracy of the developed numerical model.

Enhancing the energy utilization in parabolic trough concentrators with cracked heat collection elements using a cost-effective rotation mechanism

The risk of vacuum loss in linear solar heat collection elements (HCEs) is one of the major practical challenges that are facing the parabolic trough solar concentrator (PTSC) systems in concentrating solar power (CSP) plants. Despite the long-life span of CSP systems, HCEs are frequently replaced due to permeated hydrogen (due to saturation of getters) or leaked air (due to failures in end metal-to-glass welding or cracked glass shells). This study proposes a low-tech solution for boosting the performance of PTSCs with partial or lost vacuum through rotating the HCEs. A carefully validated integrated 3D optical-thermal model is developed and used to quantify the energetic and exergetic performances of PTSCs with rotated and fixed HCEs for both cases of lost and maintained vacuum. Both steady and unsteady simulations are reported using high-precision ground measurements of direct irradiance and meteorological parameters. As the rotational speed increases from 0 to 20 rad/s, the energy efficiency of PTSCs with new and damaged HCEs is improved by ∼47 and 52%, respectively, at a Reynolds number of 4000 and an inlet temperature of 350 °C. By rotating a damaged HCE at only 10 rad/s, maximum improvements of ∼26 and 53% in the useful heat gain are obtained, compared to non-rotating evacuated and non-rotating damaged HCEs, respectively, at the same operating conditions. Overall, the advantage of the proposed concept is more pronounced when the PTSC is operating at relatively low flow rates, high temperatures, or under high irradiance levels.

A design method for optimizing the secondary reflector of a parabolic trough solar concentrator to achieve uniform heat flux distribution

Non-uniform solar flux distribution in a parabolic trough concentrator (PTC) causes large temperature gradients on absorber tube surface, making the PTC inefficient and damaged. To solve the problem, a novel method is proposed for designing the additional secondary reflector (SR) in a PTC to improve uniform heat flux distribution on absorber tube surface. In the design, the heat flux between upper and lower surfaces of absorber tube is well balanced by optimizing the location of absorber. Then, the SR with segmented broken-line type composed of multiple plane mirrors is delicately designed with local heat flux compensation strategy. Two case studies are conducted to compare the performances of the newly designed SRs with other existing SR designs. It is shown that the uniformity of heat flux distribution can be improved to over 90% for present SR design, much higher than those for other existing SR designs. Also, the optical efficiency of the PTC with present SR design is also increased as compared with other designs. The results indicate that this proposed method is competent for designing SR in a PTC with uniform heat flux distribution.