Three-dimensional Measurement Research Articles

Three-dimensional measurement based on equal spacing binary fringe coding

Abstract Binary fringe projection technology can effectively avoid the measurement error caused by nonlinearity in structured light three-dimensional measurement system. In this paper, a binary fringe projection coding based on equal spacing is proposed firstly, the image sequence projected by binary fringes with equal spacing is corresponding to the sinusoidal intensity values in the same period one by one, and then the sinusoidal fringes are generated by weighted superposition. The experimental results show that, compared with the traditional four-step and 12-step phase shifting methods, the mean square error of the synthesized sinusoidal pattern is reduced by 36.74% and 18.24% respectively, and the mean square error of the distance between the obtained spherical point cloud of the standard sphere and the center of the fitting standard sphere is reduced by 89.36% and 77.27% respectively.

A dataset describing chip parameters for rock breaking by chisel pick under deep-sea hydrostatic pressure

Chip is a visual representation of rock breaking by cutter, and their related parameters are crucial for revealing the rock breaking mechanism in deep-sea mining. Based on sieving and three-dimensional size measurement methods widely used in mining engineering, this paper reports a dataset of chip parameters for rock breaking by chisel pick under deep-sea hydrostatic pressure. Specifically, we first designed an experimental setup that can accurately simulate deep-sea hydrostatic pressure, conducted rock breaking experiments and carefully collected chips. Subsequently, those chips were sieved, high-resolution images were collected, and the coarseness index (CI), chip size uniformity (n), absolute chip size (de), and fractal dimension (D) were measured. Finally, three-dimensional size (long, intermediate and short) was measured for 3064 chips with particle sizes greater than 4.75 mm. This dataset will be used by researchers to validate numerical simulations or optimize equipment structures related to deep-sea mining, including deep-sea rock mechanics, mining cutter and conveyor pipes.

Multiethnic Growth Standards for Fetal Body Composition and Organ Volumes Derived from 3D Ultrasonography

BackgroundA major goal of contemporary obstetrical practice is to optimize fetal growth and development throughout pregnancy. To date, fetal growth during prenatal care is assessed by performing ultrasonographic measurement of two-dimensional fetal biometry to calculate an estimated fetal weight. Our group previously established two-dimensional fetal growth standards using sonographic data from a large cohort with multiple sonograms. A separate objective of that investigation involved the collection of fetal volumes from the same cohort. ObjectiveThe Fetal 3D Study was designed to establish standards for fetal soft tissue and organ volume measurements by three-dimensional ultrasonography and compare growth trajectories with conventional two-dimensional measures where applicable. Study DesignThe NICHD Fetal 3D Study included research-quality images of singletons collected in a prospective, racially and ethnically diverse, low-risk cohort of pregnant individuals at 12 U.S. sites, with up to five scans per fetus (N=1,730 fetuses). Abdominal subcutaneous tissue thickness was measured from two-dimensional images and fetal limb soft tissue parameters extracted from three-dimensional multiplanar views. Cerebellar, lung, liver and kidney volumes were measured using virtual organ computer aided analysis (VOCAL). Fractional arm and thigh total volumes, and fractional lean limb volumes were measured, with fractional limb fat volume calculated by subtracting lean from total. For each measure, weighted curves (5th, 50th, 95th percentiles) were derived from 15-41 weeks’ using linear mixed models for repeated measures with cubic splines. ResultsSubcutaneous thickness of the abdomen, arm, and thigh increased linearly, with slight acceleration around 27-29 weeks. Fractional volumes of the arm, thigh, and lean limb volumes increased along a quadratic curvature, with acceleration around 29-30 weeks. In contrast, growth patterns for two-dimensional humerus and femur lengths demonstrated a logarithmic shape, with fastest growth in the 2nd trimester. The mid-arm area curve was similar in shape to fractional arm volume, with an acceleration around 30 weeks, whereas the curve for the lean arm area was more gradual. The abdominal area curve was similar to the mid-arm area curve with an acceleration around 29 weeks. The mid-thigh and lean area curves differed from the arm areas by exhibiting a deceleration at 39 weeks. The growth curves for the mid arm and thigh circumferences were more linear with some decelerations. Cerebellar two-dimensional diameter increased linearly, whereas cerebellar three-dimensional volume growth gradually accelerated until 32 weeks and then decelerated. Lung, kidney, and liver volumes all demonstrated gradual early growth followed by a linear acceleration beginning at 25 weeks for lungs, 26-27 weeks for kidneys, and 29 weeks for liver. ConclusionGrowth patterns and timing of maximal growth for three-dimensional lean and fat measures, limb and organ volumes differed from patterns revealed by traditional two-dimensional growth measures, suggesting these parameters reflect unique facets of fetal growth. Growth in these three-dimensional measures may be altered by genetic, nutritional, metabolic or environmental influences and pregnancy complications, in ways not identifiable using corresponding two-dimensional measures. Further investigation into the relationships of these three-dimensional standards to abnormal fetal growth, adverse perinatal outcomes, and health status in postnatal life is warranted.

Feasibility and reproducibility of new technique for measurement of transverse diameter of levator ani muscle hiatus using two-dimensional transperineal ultrasound in nulliparous women with term pregnancy.

The aim of the present study was two-fold. Firstly, we aimed to develop and describe a technique for measurement of the transverse diameter (TD) of the levator ani muscle (LAM) hiatus in the coronal view using two-dimensional (2D) transperineal ultrasound (TPUS) in nulliparous women with a term pregnancy. Secondly, we aimed to evaluate the feasibility and reproducibility of 2D-TPUS assessment of LAM hiatal TD and assess intermethod agreement between 2D-TPUS and three-dimensional (3D) TPUS measurement of TD in the axial plane, which is considered the gold standard in nulliparous women with term pregnancy. We recruited a group of nulliparous women with term pregnancy before the onset of labor. The study was conducted in two phases: Phase 1 involved developing and describing the 2D-TPUS technique for measuring LAM hiatal TD, and Phase 2 focused on assessing the technique's feasibility, reproducibility and intermethod agreement with 3D-TPUS measurement of LAM hiatal TD. In Phase 1, we enrolled 30 women. Each woman underwent acquisition of a 3D-TPUS volume, which was analyzed using multiplanar mode to identify and determine the appearance of the lateral borders of the LAM in the coronal plane, at the level of the plane of minimal hiatal dimensions. These borders were used as landmarks for TD measurement. Additionally, we measured the distance between the plane used for TD measurement and the center of the urethra in the axial view. In Phase 2, we recruited 100 women. Each woman underwent acquisition of three 2D-TPUS videoclips in the coronal plane, each encompassing a sweep of the entire LAM hiatus, and a 3D volume, all obtained during rest. On the 2D videoclips, TD was measured twice by one operator and once by another operator. In the 3D volume, TD was measured once, by one operator, in the axial plane; this measurement was considered the gold standard. Each operator was blinded to all other measurements during their assessments. We analyzed intraobserver and interobserver reproducibility and performed an intermethod (2D vs 3D) comparison. Bland-Altman analysis was conducted, and Levene's W0 test and Student's t-test were performed to explore clinical factors that might contribute to systematic differences. In Phase 1, we identified successfully the landmarks denoting the lateral borders of the LAM hiatal TD in the coronal view. These appeared as two symmetrical hypoechogenic indentations located at the inner border of the hyperechogenic structure of the LAM, at the point of maximum distance between the two sides of the LAM. The distance between the urethra and the plane where TD should be measured using 3D-TPUS in the axial plane had a median of 4 mm and varied from 0 to 9 mm. This enabled us to describe a method for assessing LAM hiatal TD in the coronal plane using 2D-TPUS. In Phase 2, LAM hiatal TD was measured successfully in all 2D and 3D acquisitions from the entire group of 100 women. The analyses for intraobserver and interobserver reproducibility and the intermethod comparison (2D vs 3D) revealed almost perfect agreement in TD measurements using 2D-TPUS, with intraclass correlation coefficients of 0.95 (95% CI, 0.92-0.96), 0.87 (95% CI, 0.78-0.92) and 0.85 (95% CI, 0.78-0.90), respectively. The average differences between measurements were 0.1 mm for intraobserver, 1.0 mm for interobserver and 0.2 mm for intermethod repeatability. No systematic differences were observed in any of the measurement sets, except in the interobserver analysis, although this difference was clinically not significant (38.2 vs 37.2 mm, P = 0.01). None of the examined clinical factors (maternal body mass index and maternal age) exhibited a statistically significant impact on intraobserver, interobserver or intermethod reliability. Utilizing our technique, described herein, to measure the LAM hiatal TD in the coronal view using 2D-TPUS is not only feasible but also highly reproducible and accurate in nulliparous women with term pregnancy. Moreover, it yields measurements that are comparable to those obtained in the reconstructed axial plane generated by 3D-TPUS. © 2024 International Society of Ultrasound in Obstetrics and Gynecology.

Formation of tendinous intersections in the human fetal rectus abdominis.

Previous studies have poorly described the initial development process of the tendinous intersections of the rectus abdominis muscle (RAM). The present study aimed to observe the formation of tendinous intersections in the RAM during the early fetal period using diffusion tensor imaging (DTI). Fifteen human fetal specimens (crown-rump length [CRL]: 39.5-93.7 mm) were selected. Three-dimensional measurements revealed that Zone-4 (i.e., the zone between the pubic symphysis and the caudal base of the umbilical ring in the RAM) had a smaller width and was thicker than Zone-1 and Zone-2 (i.e., the zones between the costal arch and the cranial base of the umbilical ring) and Zone-3 (i.e., the zone at the umbilical ring). Characteristics of tendinous intersections in the RAM during the early fetal period were assessed according to number, size, type, laterality, and sex. The mean number of tendinous intersections on both sides was 3.1 (range: 2.0-4.0), and 21% of specimens had only two tendinous intersections, which was higher than that reported in previous adult studies. The present data suggest that the formation of tendinous intersections was still in progress in specimens with two tendinous intersections in the RAM and that the third tendinous intersection was formed in Zone-2. Ordinal logistic regression via generalized estimating equations revealed that the odds for a higher type of tendinous intersections in Zone-1 and Zone-2 were significantly higher than those in Zone-4 (adjusted odds ratio: 14.85, 8.84). The odds for the presence of incomplete types (tendinous intersections that could not completely transverse the RAM) in Zone-3 were significantly higher than those in Zone-1 (adjusted odds ratio: 7.4). The odds for missing tendinous intersections in Zone-4 were significantly higher than those in Zone-1 (adjusted odds ratio: 20.5). These zonal differences in the formation of tendinous intersections were consistent with those observed in previous adult studies. In this study, DTI detected tendinous intersections in a sample with a CRL of 45.8 mm (approximately 11 weeks of gestation), which is earlier than that in previous histological findings, indicating that the RAM does not have mature tendinous intersections until the 17th week of gestation. In conclusion, DTI could detect the premature differentiation of tendinous intersection formation. Our data may aid in elucidating the developmental processes of tendinous intersections in the RAM.

Efficient and robust 3D reconstruction: Absolute phase extraction algorithm based on three gray images

The structured light three-dimensional (3D) measurement technology based on optical metrics has gained increasing applications, and there is a growing demand for capturing transient trajectory changes in dynamic scenes. Conventional temporal phase unwrapping (TPU) approaches often require multi-frequency fringe patterns for application. However, the inevitable conflict arises between the number of projected fringe patterns and the measurement speed. This paper proposes a highly accurate and robust 3D measurement method using only 3-step phase-shifting fringe patterns. To precisely reconstruct the 3D shape using the fewest fringe patterns, it is essential to extract as much information as possible from the available patterns. Therefore, we calculate the wrapped phase distribution using 3-step phase-shifting fringe patterns to ensure accuracy. Simultaneously, the trapezoidal phase-shifting method is employed to calculate the intensity ratio distribution. Through the proposed region-based indexing method, the intensity ratio map is transformed into an unwrapped phase map. Additionally, a novel self-correction method is introduced to correct the non-linear errors in the unwrapped phase map, which is then utilized for the calculation of the fringe order required for phase unwrapping. This high-speed measurement method utilizes only 3-step phase-shifting fringe patterns while retaining the advantages of TPU, meeting the requirements of high-speed and full-field measurements. Experimental results on both static and dynamic scenes validate the effectiveness and versatility of the proposed method, demonstrating its flexibility and simplicity in application. In our 3D measurement system, the method achieves 3D reconstruction of the dynamic object's trajectory at a measurement speed of 107 frames per second.

Visiting experience of digital museum interior design based on virtual reality and sensor networks

China's computer technology and image sensor technology are both rapidly developing, and the related advantages of digital holography technology are gradually expanding. These technologies have been applied in many fields. For example, three-dimensional measurement, deformation measurement, and anti-counterfeiting fields. This article combines holographic technology and virtual reality technology, and applies them to the interior design of digital museums and the optimization of auxiliary visits. A corresponding mathematical calculation model is established for digital holographic images, and in-depth research is conducted on this mathematical calculation model. Relevant personnel have also conducted relevant research on commonly used digital holography technology, and provided a detailed introduction to the principles of virtual reality technology. They have also conducted in-depth research on the specific working principles of VR technology and the application technology of virtual reality systems. Finally, an analysis and research were conducted on the development of Chinese museums, and a new perspective was proposed on the indoor space of museums under the new digital concept, which has certain reference significance. Currently, Chinese museums are thriving, so deepening the interior space of museums is very important. This article hopes to provide some guidance and practical value for the development of Chinese museums.

Indirect Head of the Rectus Femoris Tendon as a Graft for Segmental Hip Labral Reconstruction: An Anatomic, Radiographical, and Biomechanical Study in Comparison With Iliotibial Labral Reconstruction

Background: The indirect head of the rectus femoris (IHRF) tendon has been used as an autograft for segmental labral reconstruction. However, the biomechanical properties and anatomic characteristics of the IHRF, as they relate to surgical applications, have yet to be investigated. Purpose: To (1) quantitatively and qualitatively describe the anatomy of IHRF and its relationship with surrounding arthroscopically relevant landmarks; (2) detail radiographic findings pertinent to IHRF; (3) biomechanically assess segmental labral reconstruction with IHRF, including restoration of the suction seal and contact pressures in comparison with iliotibial band (ITB) reconstruction; and (4) assess potential donor-site morbidity caused by graft harvesting. Study Design: Descriptive laboratory study. Methods: A cadaveric study was performed using 8 fresh-frozen human cadaveric full pelvises and 7 hemipelvises. Three-dimensional anatomic measurements were collected using a 3-dimensional coordinate digitizer. Radiographic analysis was accomplished by securing radiopaque markers of different sizes to the evaluated anatomic structures of the assigned hip.Suction seal and contact pressure testing were performed over 3 trials on 6 pelvises under 4 different testing conditions for each specimen: intact, labral tear, segmental labral reconstruction with ITB, and segmental labral reconstruction with IHRF. After IHRF tendon harvest, each full pelvis had both the intact and contralateral hip tested under tension along its anatomic direction to assess potential site morbidity, such as tendon failure or bony avulsion. Results: The centroid and posterior apex of the indirect rectus femoris attachment are respectively located 10.3 ± 2.6 mm and 21.0 ± 6.5 mm posteriorly, 2.5 ± 7.8 mm and 0.7 ± 8.0 mm superiorly, and 5.0 ± 2.8 mm and 22.2 ± 4.4 mm laterally to the 12:30 labral position. Radiographically, the mean distance of the IHRF to the following landmarks was determined as follows: anterior inferior iliac spine (8.8 ± 2.5 mm), direct head of the rectus femoris (8.0 ± 3.9 mm), 12-o’clock labral position (14.1 ± 2.8 mm), and 3-o’clock labral position (36.5 ± 4.4 mm). During suction seal testing, both the ITB and the IHRF reconstruction groups had significantly lower peak loads and lower energy to peak loads compared with both intact and tear groups (P = .01 to .02 for all comparisons). There were no significant differences between the reconstruction groups for peak loads, energy, and displacement at peak load. In 60° of flexion, there were no differences in normalized contact pressure and contact area between ITB or IHRF reconstruction groups (P > .99). There were no significant differences between intact and harvested specimen groups in donor-site morbidity testing. Conclusion: The IHRF tendon is within close anatomic proximity to arthroscopic acetabular landmarks. In the cadaveric model, harvesting of the IHRF tendon as an autograft does not lead to significant donor-site morbidity in the remaining tendon. Segmental labral reconstruction performed with the IHRF tendon exhibits similar biomechanical outcomes compared with that performed with ITB. Clinical Relevance: This study demonstrates the viability of segmental labral reconstruction with an IHRF tendon and provides a detailed anatomic description of the tendon in the context of an arthroscopic labral reconstruction. Clinicians can use this information during the selection of a graft and as a guide during an arthroscopic graft harvest.

Geometric Error Identification of Gantry-Type CNC Machine Tool Based on Multi-Station Synchronization Laser Tracers

Laser tracers are a three-dimensional coordinate measurement system that are widely used in industrial measurement. We propose a geometric error identification method based on multi-station synchronization laser tracers to enable the rapid and high-precision measurement of geometric errors for gantry-type computer numerical control (CNC) machine tools. This method also improves on the existing measurement efficiency issues in the single-base station measurement method and multi-base station time-sharing measurement method. We consider a three-axis gantry-type CNC machine tool, and the geometric error mathematical model is derived and established based on the combination of screw theory and a topological analysis of the machine kinematic chain. The four-station laser tracers position and measurement points are realized based on the multi-point positioning principle. A self-calibration algorithm is proposed for the coordinate calibration process of a laser tracer using the Levenberg–Marquardt nonlinear least squares method, and the geometric error is solved using Taylor’s first-order linearization iteration. The experimental results show that the geometric error calculated based on this modeling method is comparable to the results from the Etalon laser tracer. For a volume of 800 mm × 1000 mm × 350 mm, the maximum differences of the linear, angular, and spatial position errors were 2.0 μm, 2.7 μrad, and 12.0 μm, respectively, which verifies the accuracy of the proposed algorithm. This research proposes a modeling method for the precise measurement of errors in machine tools, and the applied nature of this study also makes it relevant both to researchers and those in the industrial sector.

Study on gamma correction for three-dimensional fringe projection measurement based on attention U-Net network

Study on gamma correction for three-dimensional fringe projection measurement based on attention U-Net network

Three 1-bit speckle-embedded pulse-width modulation patterns for robust absolute 3D measurement

In three-dimensional (3D) shape measurement techniques using structured light, 1-bit pulse-width modulation (PWM) patterns and 1-bit speckle patterns can be projected at high speed. However, when combining PWM and speckle patterns to integrate their advantages, the decoupling problem is insurmountable. In this work, a novel 1-bit speckle-embedded PWM (SPPWM) method was proposed to achieve absolute 3D shape measurement using only three binary patterns. Our method consists of three main steps: First, a sinusoidal pattern reconstruction network was proposed to eliminate the high-order harmonics and speckle patterns in the SPPWM patterns and obtain high-quality sinusoidal patterns. Second, a multi-temporal spatial correlation matching algorithm was proposed to obtain a coarse disparity map from the three SPPWM patterns. Third, the high-accuracy wrapped phase map is used as an additional constraint for refining the coarse disparity map to obtain the final high-accuracy disparity map for absolute 3D measurement without phase unwrapping. Our method combines the advantages of fringe projection profilometry techniques for high-precision wrapped phase retrieval and speckle correlation matching algorithms for robust and unambiguous disparity map calculation. The experimental results demonstrated that our method could realize high-precision absolute 3D shape measurement with an accuracy of 0.057 mm using only three 1-bit SPPWM patterns. Furthermore, different simulation noises were used to demonstrate the robustness of the proposed method.

Older age is associated with decreased overall shoulder strength but not direction-specific differences in the three-dimensional feasible torque space

Shoulder strength is reduced in older adults but has only been assessed in planar motions that do not reflect the diverse requirements of daily tasks. We quantified the impact of age on strength spanning the three degrees of freedom relevant to shoulder function, referred to as the feasible torque space. We hypothesized that the feasible torque space would differ with age and expected this age-effect to reflect direction-specific deficits. We measured strength in 32 directions to characterize the feasible torque space of the shoulder in participants without shoulder pain or tendinous pathology (n = 39, 19–86 years). We modeled the feasible torque space for each participant as an ellipsoid, computed the ellipsoid size and direction-specific metrics (ellipsoid position, orientation, and shape), and then tested the effect of age on each metric. Age was negatively associated with ellipsoid size (a measure of overall strength magnitude; −0.0033 ± 0.0007 (Nm/kg)/year, p < 0.0001). Contrary to our expectation, the effect of age on the direction-specific metrics did not reach statistical significance. The effect of age did not differ significantly between male and female participants. Three-dimensional strength measurements allowed us to constrain the direction of participants’ maximum torque production and characterize the entire feasible torque space. Our findings support a generalized shoulder strengthening program to address age-related shoulder weakness in those without pain or pathology. Clinical exam findings of imbalanced weakness may suggest underlying pathology beyond an effect of age. Longitudinal studies are needed to determine the positive or negative impact of our results.

Dynamic three-dimensional measurement by spatial-domain phase-shifting method based on fringe projection profilometry

Dynamic three-dimensional measurement by spatial-domain phase-shifting method based on fringe projection profilometry

Highly accurate three-dimensional measurement of large structures using multiple stereo vision with improved two-step calibration algorithm

A multiple stereo-based three-dimensional (3D) measurement method of large-scale structures is presented, which replaces time-consuming and laborious 3D measurement procedure of laser-based conventional equipment. To have 3D reconstruction accuracy with millimeter-precision, two-step calibration algorithms are improved. Specifically, we use 2D epipolar constraint, using fundamental matrix determined by matched points, to new combination of objective function for intrinsic parameter calibration. We additionally propose an onsite structure parameter calibration algorithm using different epipolar constraint of measurement points in images of large ship block as well as reprojection error of checkerboard, to bypass the limitation of the coverage of checkerboard in large-scale measurement. The actual 3D measurement of the three ship blocks is conducted, and the 3D reconstruction accuracy is validated by comparing the 3D coordinates measured by total station. The experimental results showed that the mean 3D reconstruction error ranged from 6 to 14 mm.

Three-dimensional shape measurement technique for hot and shiny forging

For hot and shiny forging, rapid optical three-dimensional (3D) shape measurement can find the defects in time, improve manufacturing efficiency and reduce manufacturing cost. Optical 3D measurement of hot and shiny forging faces following three challenges. (a) Influence of blackbody radiation on the red band of visible light leads to saturation of captured fringe pattern. (b) Infrared band of blackbody radiation causes the camera to heat up. (c) Specular reflection of shiny forging leads to local saturation of captured fringe pattern. To address the above issues, we propose an effective optical 3D measurement scheme for hot and shiny forging in this paper. Firstly, the experiments demonstrate that the influence of blackbody radiation on visible light is concentrated in red light band and has no crosstalk in the blue light band, so we adopt blue light projection and blue light band-pass filter (BBF) to capture clear fringe pattern. Secondly, since the BBF cannot block the near-infrared component, we use an infrared light cutoff filter (ICF) to reduce the thermal effect of blackbody radiation. Finally, we analyze the Fourier transform (FT) spectrum of saturated fringe pattern caused by specular reflection, and propose an efficient Butterworth low-pass filtering (BLPF) method that does not require additional hardware, algorithm processing, and image assistance. The experimental results verify the effectiveness of the proposed scheme.

A three-dimensional algorithm for precise measurement of human auricle parameters

Measurement of auricle parameters for planning and post-operative evaluation presents substantial challenges due to the complex 3D structure of the human auricle. Traditional measurement methods rely on manual techniques, resulting in limited precision. This study introduces a novel automated surface-based three-dimensional measurement method for quantifying human auricle parameters. The method was applied to virtual auricles reconstructed from Computed Tomography (CT) scans of a cadaver head and subsequent measurement of important clinically relevant aesthetical auricular parameters (length, width, protrusion, position, auriculocephalic angle, and inclination angle). Reference measurements were done manually (using a caliper and using a 3D landmarking method) and measurement precision was compared to the automated method. The CT scans were performed using both a contemporary high-end and a low-end CT scanner. Scans were conducted at a standard scanning dose, and at half the dose. The automatic method demonstrated significantly higher precision in measuring auricle parameters compared to manual methods. Compared to traditional manual measurements, precision improved for auricle length (9×), width (5×), protrusion (5×), Auriculocephalic Angle (5–54×) and posteroanterior position (23×). Concerning parameters without comparison with a manual method, the precision level of supero-inferior position was 0.489 mm; and the precisions of the inclination angle measurements were 1.365 mm and 0.237 mm for the two automated methods investigated. Improved precision of measuring auricle parameters was associated with using the high-end scanner. A higher dose was only associated with a higher precision for the left auricle length. The findings of this study emphasize the advantage of automated surface-based auricle measurements, showcasing improved precision compared to traditional methods. This novel algorithm has the potential to enhance auricle reconstruction and other applications in plastic surgery, offering a promising avenue for future research and clinical application.

No significant change of tibiofemoral rotation after femoral rotational osteotomy in patients with patellofemoral instability.

An increased value of tibiofemoral rotation is frequently observed in patients with patellofemoral instability or maltracking. Nevertheless, the appropriate approach for addressing this parameter remains unclear so far. One potential approach for correcting tibiofemoral rotation is femoral rotational osteotomy. We hypothesized that femoral rotational osteotomy affects tibiofemoral rotation. All patients who underwent femoral rotational osteotomy between January 2018 and May 2022 were included in this study. Pre- and postoperative tibiofemoral rotation and the degree of femoral rotation were measured using two-dimensional (2D) and three-dimensional (3D) measurements. The effect of femoral rotation on tibiofemoral rotation was assessed. Forty knees (18 rightand 22 left) of 36 patients (28 femalesand 8 males) were included. Mean preoperative femoral torsion was 32.1 ± 10.1° in 2D and 30.8 ± 10.1° in 3D. Femoral rotation was performed by -14.1 ± 8.3° using 2D measurements and -15.0 ± 8.0° using 3D measurements. Tibiofemoral rotation changed from 9.9 ± 6.2° to 9.7 ± 6.0° (p = n.s.) in 2D, and from 10.2 ± 5.5° to 9.4 ± 5.4° (p = n.s.) in 3D. Tibiofemoral rotation showed no significant changes after femoral rotational osteotomy. Hence, femoral rotational osteotomy cannot be used to correct tibiofemoral rotation in addition to correcting the femoral version. Other surgical techniques need to be evaluated if correction of tibiofemoral rotation is required. Level III.

An integrated uncrewed aerial vehicle platform with sensing and sampling systems for the measurement of air pollutant concentrations

Abstract. In this study, an uncrewed aerial vehicle (UAV) platform with sensing and sampling systems was developed for three-dimensional (3D) measurements of air pollutant concentrations. The sensing system of this platform contains multiple microsensors and Internet of Things devices for determining the 3D distributions of four critical air pollutants and two meteorological parameters in real time. Moreover, the sampling system comprises remote-controllable gas sampling kits, each of which contains a 1 L Tedlar bag for the 3D measurement of volatile organic compound (VOC) concentrations according to the Toxic Organics-15 (TO-15) method of the US Environmental Protection Agency. The performance of the developed UAV platform was verified in experiments where it was used to detect air pollutant emissions from a large industrial zone in Taiwan that included a traditional industrial park, a precision machinery park, and a municipal waste incineration plant. Three locations were selected as field measurement sites according to the prevailing local wind direction. The vertical distributions of four critical air pollutants, the ambient temperature, and the relative humidity were determined from data gathered at the aforementioned sites in March and May 2023. A total of 56 and 72 chemical species were qualitatively and quantitatively analyzed in these two periods, respectively. The experimental results verified the feasibility of using the proposed UAV platform for accurately evaluating the air pollutant concentration distribution and transport in an industrial zone. The sampling system can be used as the sampling part of the TO-15 method, thus extending the method to measure the 3D distribution of VOCs in an area. The UAV platform can serve as a useful tool in the management of and decision-making process for air pollution in industrial areas.

Three-dimensional micro-force measurement method based on broadband optical coherence

In response to the high-precision and multi-dimensional force measurement requirements in the fields of biology and medicine, this paper proposes a novel three-dimensional microforce measurement method based on the broadband optical coherence. A novel, compact, and low-coupling elastic element was designed, with a maximum outer diameter of 26 mm and a capacity of 50 g in the X-, Y-, and Z-directions, respectively. The functional relationship between the displacements of the three detecting points on the elastic element and the applied external force was derived based on the elastic mechanics theory. And it was also verified by the finite element method. A self-built optics system was set up to sense the displacements of the three points on the elastic element. The experiments results showed that the resolution in the X-, Y-, and Z-directions was 0.10 mN, 0.11 mN and 0.13 mN, respectively. In the measuring range of (10–50) g, the maximum coupling rate was 4.55 %, and the maximum linear error was 4.70 %. The maximum repeatability error was only 0.615 %. The method and sensor were verified with good characteristics of high resolution, low coupling rate, high linearity and high accuracy, comparing to other reported researches. The multi-dimensional force measuring method could be used in the fields of biology and medicine.

Morphological insights into the three-dimensional complexity of rhodolith beds

The ecological importance of rhodolith beds stems from their role as structurally complex three-dimensional habitat formed by free-living red calcareous algae. Their structural singularity is due to the great variety of complex and branching morphologies exhibited by rhodoliths that create interstitial spaces and increase their surface area. This increases the ecological niches for cryptofauna and provide refuge for a high number of organisms, which is why rhodolith beds are considered biodiversity hotspots. In this work, we studied a rhodolith bed located in the Menorca Channel, formed by several species of red calcareous algae that exhibit a great variety of morphologies and form an extensive and heterogeneous habitat. This study explored the morphological diversity of the rhodolith bed, comparing the ‘Core Habitat’ (within the center of the bed with the highest densities of rhodoliths) with the boundaries or ‘Adjacent Habitat’ where rhodolith density was lower. Our results show that all rhodolith growth forms (branched, pralines and boxwork) in the Core Habitat had higher interstitial space and were larger than the ones from adjacent zones. Moreover, we explored the three-dimensional techniques to study the morphological characteristics that have historically been studied in two dimensions. This study contributes to the knowledge of morphological diversity in well-preserved rhodolith beds from continental shelves in the western Mediterranean Sea and reinforces the use of three-dimensional measurements, specifically the interstitial space of branched rhodoliths, to provide more accurate data on habitat complexity.