Thermal Stability Research Articles

Theoretical exploration of energetic molecular design strategy: functionalization of C or N and structural selection of imidazole or pyrazole.

In researching energetic materials with high energy density, it is an effective method to introduce explosophoric groups. In this study, four series of energetic compounds were designed by functionalizing with C- or N-, introducing energetic groups -CH(NO2)2, -CF(NO2)2, -C(NO2)2(NF2), -C(NO2)3, and-CH(NF2)2 into imidazole and pyrazole structures. Density functional theory was employed to optimize the structure of the target compound and subsequently to predict and evaluate its performance based on this. Meanwhile, the sensitivity of the compounds was predicted based on their electrostatic potential analysis. Following analysis of the geometric structure, detonation performance, and sensitivity of the compounds, three factors were discussed: energetic groups, functionalization methods, and skeleton structure differences. The results indicate that C-functionalization has advantages only in density, but N-functionalization is better in thermal stability, heat of formation, and sensitivity. Meanwhile, the data shows that imidazole-based compounds exhibited greater density and detonation performance in the target compounds designed within this study, while pyrazoles have a higher heat of formation and chemical stability. By analyzing the design strategy of C- or N-functionalization of novel high-energy groups on energetic imidazole or pyrazole rings and selecting a more suitable molecular construction strategy, this study provides a theoretical approach for the development of new energetic materials with excellent performance. Gaussian 09 and Multiwfn 3.8 packages are the software used for calculation, and the electrostatic potentials were depicted using the VMD program. In this study, the imidazole and pyrazole derivatives were optimized at the B3PW91/6-311G (d, p) level to acquire the relevant data for the compounds.

Photocurable Thiol-Ene/Nanocellulose Elastomeric Composites for Bioinspired and Fluorine-Free Superhydrophobic Surfaces.

Artificially prepared superhydrophobic surfaces toward a self-cleaning "lotus effect" and anticontamination performance have become critically important in the past few years. However, most approaches to create the required topology with a hierarchical roughness comprise several manufacturing steps of varying practicality. Moreover, the desired low surface energy is in most cases achieved with fluorinated moieties that are currently criticized due to biological and environmental hazards. In this work, rapidly photocuring but weak thiol-ene resins were reinforced with cellulose nanofibrils (CNFs) to replicate lotus leaves via one-step UV nanoimprint lithography. The CNFs were surface-modified using countercation exchange of carboxyl groups and grafting of thiol and methacrylate functionalities. The formulation methodology resulted in free-flowing, shear-thinning composite resins without surfactants or dispersants. The rheological and photo-cross-linking behavior of the resins, the thermal stability, the mechanical performance, and the hydrophobicity of the cured composites were characterized. Notably, the surface modifications increased the as received fibril diameter (1.9 ± 0.6 nm) by 1.6-2.3 nm and raised the fibril-resin compatibility. The resins underwent rapid polymerization and the high thermal stability of thiol-enes was retained. The methacrylated nanofibrils (10 vol %) significantly strengthened the rubbery network, outperforming the neat thiol-ene polymer in terms of hardness (3.4×), reduced modulus (5.8×), and wear resistance (>100×). Moreover, the surface of lotus-texturized composites was superhydrophobic with a water contact angle of 155°, higher than that of the neat polymer (147°), and was self-cleaning. These CNF composite resins are compatible with fast-cure processes such as 3D printing and roll-to-roll processing, are exempt of fluorine or any other hydrophobization treatment, and are extremely wear-resistant.

Insight into performance and lifetime of ecofriendly pollution barriers in landfill for emergency: A thermogravimetric analysis for novel polymer materials

The novel polymer barrier wall is an in-situ remediation technology designed to effectively control the migration of pollution and prevent the diffusion of pollutants by blocking, sealing, or altering the direction of groundwater flow. With its advantages of rapid chemical reaction (achieving 95 % strength within 15 min) and portable equipment suitable for narrow and rugged emergency sites, this innovative polymer barrier demonstrates promising prospects for practical application. Hence, ensuring the long-term durability of new materials under corrosive and high-temperature leachate conditions is crucial. In this study, a comprehensive investigation was conducted on the corrosion and thermal aging performance of novel polymer materials. Firstly, the mechanical tensile properties of the polymer materials were examined after immersion in leachates, aiming to elucidate the degradation mechanism underlying these properties. Subsequently, thermogravimetric (TG) analysis was performed on the polymer materials immersed in various leachates. And the thermal stability and oxidation stability of novel materials were investigated using a thermogravimetric analyzer coupled with a Fourier transform infrared spectrometer (TG-FTIR). Based on the results obtained from thermal analysis, the service life of polymer materials under different pollutants was ultimately predicted utilizing the Arrhenius model. The findings indicate that the novel polymer materials exhibit commendable durability and pose little risk of causing secondary pollution.

Bioactive electrospun zein fibers integrated with ZnO nanoparticles: In vitro investigations

The objective of the current study was the fabrication and characterization of electrospun zein-ZnO fibers containing various concentrations of cumin essential oil (CEO) (0, 1, 2, and 3% (v/v)). The electrospinning solution's apparent viscosity, conductivity, and surface tension were measured. Also, the electrospun's morphological, color, encapsulation efficiency, antioxidant and antimicrobial properties, thermal stability, and release kinetic were investigated. The results represented that following the increase in CEO concentration, the conductivity and surface tension of the electrospinning solution changed from 182.92 μS/cm to 145.22 μS/cm and 19.52 mN/m to 22.35 mN/m, respectively. The scanning electron microscope (SEM) revealed the homogenous and free-bead structure of electrospun fibers. Besides, the diameter of fibers enhanced with a rise in CEO concentration from 217.13 nm to 321.67 nm. The finding estimated the maximum encapsulation efficiency and loading capacity at about 95.09% and 25.65%, respectively in electrospun containing the highest concentration of CEO (3%). CEO inclusion in electrospinning fibers augmented the value of contact angle, color difference, TPC, antioxidant, and antimicrobial properties. The favorable interaction between the CEO ingredients and electrospinning fibers was confirmed through FTIR and XRD analysis. Furthermore, the incorption of CEO enhanced the thermal stability of fibers. Release kinetic in different simulant (aqueous, acidic, alkaline, and fatty) revealed that Fick's diffusion was the main release mechanism. The highest diffusion coefficient was observed in electrospun fibers containing 3% CEO in the fatty media simulant. These findings could present a new horizon into electrospinning fiber's application in various fields of medicine, tissue engineering, food, and pharmaceutical industry.

Examining the Influence of Silver(I) Ion Coordination Environment in Ionic Liquids on Olefin-Paraffin Separations using Inverse Gas Chromatography.

Silver(I) ions (Ag+) undergo selective π-complexation with olefins and have been employed as separation media for the isolation of olefins from structurally similar paraffins. Ionic liquids (ILs) possess minimal vapor pressures, exceptional thermal stabilities, low melting points, as well as provide a favorable environment for π-complexation between Ag+ ions and olefins. The development of molecular drivers capable of highly selective olefin/paraffin separation systems with Ag+-containing ILs necessitates a comprehensive understanding of all factors that affect olefin solubility and selectivity. This study examines how coordinating different ligand species to Ag+ ions produces separation media with varying interaction strengths to olefins. Four coordination compounds, (4,4'-dimethyl-2,2'-bipyridine)silver(I) bis[(trifluoromethyl)sulfonyl]imide ([Ag+(DMBP)][NTf2-]), bis(pyridine)silver(I) [NTf2-] ([Ag+(Py)2][NTf2-]), bis(2,6-lutidine)silver(I) [NTf2-] ([Ag+(Lut)2][NTf2-]), and (triphenylphosphine)silver(I) [NTf2-] ([Ag+(PPh3)][NTf2-]) were dissolved in the 1-decyl-3-methylimidazolium [NTf2-] ([DMIM+][NTf2-]) IL and employed as stationary phases for inverse gas chromatography. Ligand coordination to the Ag+ ion was observed to modulate interactions of unsaturated hydrocarbons. The [Ag+(Py)2][NTf2-] complex offered the greatest olefin retention among the coordination complexes reaching 54% of the 1-octene retention factor of the uncoordinated [Ag+][NTf2-]. Hydrogen (H2) exposure studies showed ligand-dependent rates of reduction from Ag+ ion to elemental silver (Ag0). The [Ag+(PPh3)][NTf2-] complex exhibited superior stability, compared to the neat [Ag+][NTf2-] salt, reducing the retention factor of 1-octene by 15.3% and 19.4%, respectively, after 200 h of H2 exposure at 70 °C. The results from this study show that coordination complexes with Ag+ ions are useful in highly selective and efficient petroleum processing systems.

A promising pullulan/PLA composite: Influence of pullulan in the scaffolds morphology constructed by 3D printing

AbstractManufacturing three‐dimensional scaffolds with significant rough and porous structures is advantageous in tissue regeneration approaches influencing cell growth. Thus, this work aims to study the effect of using different Pullulan contents (PULL) in the poly(lactic) acid (PLA) matrix for 3D printing scaffolds. PLA composites filler with PULL (5 and 10% wt.) were prepared in a thermokinetic mixer, extruded in a machine, and then used to print samples using a fused deposition modeling (FDM) 3D printer. The prepared filaments and scaffolds were characterized using Field emission scanning electron microscopy (FESEM), Fourier‐transform infrared spectroscopy (FTIR), thermogravimetry analyses (TGA), water contact angle (WCA), differential scanning calorimetry (DSC), and hardness techniques. The insertion of PULL into the PLA matrix influenced the increase in diameter and roughness, and density reduction of the composite filaments compared to pristine PLA. Furthermore, the filler promoted an increase in thermal stability, shore hardness, and the development of promising morphological characteristics for cell growth because the walls of the scaffolds are more robust and have more regular‐sized holes. The scaffold fabrication reinforced with 10% PULL presented high surface roughness (up to 1022% if compared with pristine PLA), and open pores can be confirmed successfully compared to pristine PLA. Thus, the use of PULL as a filler in a PLA matrix guarantees the development of composite scaffolds with improved morphological and hardness properties, which could allow the possibility of future research into the application of the proposed material (10% wt. PULL) as an ecologically correct and biocompatible alternative for application in tissue engineering.

Surface Reaction Induced Compressive Strain for Stable Inorganic Perovskite Solar Cells

AbstractCesium‐based inorganic perovskites have emerged as promising light‐harvesting materials for perovskite solar cells (PSCs) due to their promising thermal‐ and photo‐stability. However, obstacles to commercialization remain regarding their phase instability. In this work, we report a facile and effective strategy to regulate the surface compressive strain via in situ surface reaction to stabilize CsPbI3 perovskite. The use of a chelating ligand with a molecular configuration closely matching the integer multiples of the unit cell lattice parameters of CsPbI3 induces compressive strain at the surface of CsPbI3. The chemical bonding and strain modulation synergistically not only passivate film defects, but also inhibit perovskite phase degradation, thus significantly improving the intrinsic stability of inorganic perovskite. Consequently, enhanced power conversion efficiency (PCE) of 21.0 % and 18.6 % were respectively achieved in 0.16‐cm2 lab‐scale devices and 25.3‐cm2 solar modules. Further, surface reaction enables PSCs with enhanced thermal and operational stability; these devices retain over 95 % of their initial PCE after damp‐heat tests (i.e., in 85 °C and 85 % R. H. air) for 2000 h, and remain 99 % of their initial PCE after operating for 2000 h, representing one of the most stable inorganic PSCs reported so far.

Iodide Management and Oriented Crystallization Modulation for High-Performance All-Air Processed Perovskite Solar Cells.

Halide-related defects at the buried interface not only cause nonradiative recombination, but also seriously impair the long-term stability of perovskite solar cells (PSCs). Herein, a bottom-up, all-in-one modification strategy is proposed by introducing a multisite antioxidant ergothioneine (EGT) at the buried interface to manage iodide ions and manipulate crystallization dynamics. The findings demonstrate that EGT not only passivates uncoordinated Sn4+/Pb2+ defects, but also firmly anchors iodide ions and inhibits their oxidation to I2. Additionally, the modification by EGT enhances the oriented crystallization of perovskite, improves the carrier dynamics, and releases residual stresses. Consequently, the optimized all-air processed device (Rb0.02(FA0.95Cs0.05)0.98PbI2.91Br0.03Cl0.06) achieves a remarkable power conversion efficiency (PCE) of 25.13%, which is among the highest values reported for devices fabricated in air, along with ultrahigh open-circuit voltage (VOC) of 1.191V and fill factor (FF) of 84.9%. The optimized device without encapsulation exhibits strong humidity, thermal, and operational stability under ISOS protocol. Specifically, the initial efficiency of the device is retained at 90.12% after 1512 h of thermal ageing at 65°C and 90.14% after 930 h of continuous maximum power point tracking (MPPT) under simulated AM1.5 illumination.

One-pot aqueous-phase synthesis of polyimides from typical monomers

One-pot aqueous-phase synthesis of polyimides (PIs) offers great economic and environmental benefits and improves the hydrolytic stability of the precursor (polyamic acid) obviously. However, this method is only suitable for the polymerization of very limited dianhydride and diamine monomers up to now. In this study, the most commonly used dianhydrides and diamines for the preparation of commercially available PI products were selected for one-pot aqueous-phase synthesis of various polyamic acid salts (PAAS). The effects of the structure of monomers, the reaction temperature and the adding process of the organic base on the polymerization reaction were explored by rotational rheology, nuclear magnetic resonance (NMR) and Fourier transform infrared (FTIR) spectroscopy. The polymerization products obtained via the aqueous-phase route show high molecular weight when the reaction conditions have been optimized. Various PI films prepared by the thermal imidization of corresponding PAAS demonstrate good optical transparency, excellent thermal stability, and outstanding mechanical and electrical properties. This work proposes the reaction mechanism of PAAS via one-pot aqueous-phase route and utilizes this novel polymerization strategy to synthesize high-molecular-weight PIs from typical aromatic dianhydride and diamine monomers.

Superhydrophobic Electrospun PI/PTFE Membranes with Ultralow Dielectric Constants for High-Frequency Telecommunication.

High-frequency, high-power, and high-speed telecommunication in a complex environment promotes the development of dielectric materials toward a low dielectric constant, low dielectric loss, good thermal properties, and long-term reliability. Here, polyimide/polytetrafluoroethylene (PI/PTFE) nanofiber membranes with an inherent super hydrophobicity, excellent dielectric properties, good thermal stability, and enhanced tensile strength were prepared via a simple electrospinning strategy and an imidization reaction. The obtained PI/PTFE membranes demonstrate a superlow average dielectric constant of 1.22-1.27 and a dielectric loss of 0.032-0.048 in high frequency, together with an enhanced tensile strength, benefiting from the special nanofiber-bead structure formed in the composite membrane. The mixing of polyamic acid (PAA) and PTFE in the electrospinning solution endows the obtained PI/PTFE nanofiber membrane with a uniform distribution of PTFE and thus an inherent superhydrophobicity with a water contact angle of 156.1 and 159.2° for PI/PTFE-30% and PI/PTFE-40%, respectively. Besides, the hydrophobicity could be kept even after standing more than 10,000 water drops, and the thermal properties exhibited promising results with Tmax = 587 °C and Td5% = 423 °C, rendering these PI/PTFE membranes favorable alternatives for prospective telecommunication.

Sonochemical synthesis of guar gum - Zirconium phosphate composite for efficient capture of uranium from water

The increasing presence of uranium as a radionuclide contaminant in water is a threat to human health and the environment. Sonication-assisted crosslinking of guar gum, a biopolymer, is carried out with zirconium phosphate to form an adsorbent (GG@ZrP) for the removal of uranium from water. The surface characteristics, functionalities, and thermal stability of the composite were established using various analytical and spectral tools. Langmuir, Freundlich, and Sips models were used to evaluate the batch adsorption parameters. The adsorbent exhibited an excellent Langmuir adsorption capacity of 500 mg g−1 towards adsorption of uranium at pH 6. The adsorption was endothermic (ΔH, 22.63 kJ mol−1) and followed pseudo-second order kinetics. The synergistic influence of hydroxyl-rich guar gum and phosphate moieties resulted in efficient binding of uranium. With a high selectivity towards interfering cations and anions and applicability over a good range of pH, this adsorbent is a promising candidate for uranium remediation from water.

Attaining the Utmost Stability and Energy of Carbonyl Azides by the Synergistic Improvement of Conjugation and H-bonding.

Carbonyl azides are important precursors to isocyanates and are used as energetic compounds. However, the further development of these compounds is limited by their inherently poor stability. In this study, we present a new family of carbonyl azides, 5-nitro-1H-1,2,4-triazol-3-yl-carbamoyl-azide (NTCA), which was synthesized through in situ oxidation cleavage of amino-tetrazole. Compared with its precursor (nitrocarbamoyl azide, HNCA), X-ray data and quantum calculations indicate that NTCA has much stronger conjugation (dihedral angle decreased from 13.39° to 1.35°) and more H-bonds (increase from 2 to 7 pairs). As a result, NTCA exhibits the highest thermal stability (decomposition temperature of 212 °C) and highest density (1.820 g cm-3) among all known carbonyl azides. In addition, a series of Curtius rearrangements were performed to generate substituted ionic derivatives, which also exhibit high stability and energy. This study provides an effective strategy for synthesizing carbonyl azides with high stability and energy, paving the way for future practical applications.

Self-healable epoxy/graphene oxide vitrimers and their recyclable glass fiber reinforced composites

Glass fiber-reinforced polymers (GFRPs) made from thermoset polymers have been widely used across various industries. However, these composites have significant drawbacks, including poor interfacial adhesion between the fiber and matrix, as well as a substantial contribution to waste and environmental pollution due to the challenges in recycling, reprocessing, and reuse. Herein, firstly graphene oxide (GO) was incorporated in vitrimer matrix to fabricate recyclable vitrimer nanocomposites with improved interfacial interaction, high thermal stability, low dielectric constant, fast stress relaxation as well as rapid self-healing ability. The nanocomposite with 0.2 wt% GO is optimized to achieve excellent remoulding (89% of flexural strength) and self-healing (60 min for a 48 μm scratch) properties due to dynamic disulfide bond exchange mechanism. Furthermore, epoxy/GO matrix was used to develop glass fiber reinforced composites via vacuum assisted resin infusion molding process (VARIM). The developed composites demonstrate tremendous mechanical strength (250 MPa), shape-memory, weldability, and degradable properties. Due to the rapid chemical degradation of epoxy vitrimer under mild conditions in the thiol (2-mercaptoethanol and 1-otanethiol), facilitated by thiol disulfide exchange reaction, glass fibers (GFs) can be effectively recycled. The performance of recycled glass fibers closely matches that of original fibers, exhibiting nearly identical woven structure and mechanical properties. The single yarn of recycled glass fibers can achieve tensile strength of 85% (1-octanethiol) and 72% (2-mercaptoethanol) of the original glass fibers, thus, the recycling of glass fibers would be highly advantageous in terms of achieving the sustainability goals.

Green synthesis of boehmite-reinforced cashew gum/polypyrrole biopolymer blend for advanced biomaterials

Electrically conducting biopolymer blend nanocomposites based on different contents of boehmite (BHM) reinforced cashew gum (CG) /polypyrrole (PPy) blend is synthesized by an in situ polymerization technique using water as a green solvent. The resulting bio-blend nanocomposites underwent comprehensive analysis concerning their structural, morphology, thermal, and electrical properties, such as dielectric constant, dielectric loss, electric modulus, and AC conductivity. The Fourier transform infrared spectroscopy (FTIR) spectra revealed the presence of metal oxide stretching in the blended nanocomposite at 512 cm−1. Field emission scanning electron microscopy (FE-SEM) confirmed the attachment and uniform dispersion of BHM within the CG/PPy blend at 7 wt% loading, and beyond this loading, the nanoparticles get agglomerated in the biopolymer blend. The glass transition temperature and thermal stability of all the blended nanocomposites are higher than that of the pure CG/PPy blend and these thermal properties increase with the loading of nanoparticles. Conductivity experiments demonstrated that as the nanofiller content increases up to 7 wt%, there is a concurrent rise observed in AC conductivity, dielectric loss, and dielectric constant. There is a substantial difference of 1.21 Scm−1 between the maximum and minimum AC electrical conductivity, at 102 Hz. However, a decrease in electrical properties is observed at the highest loadings of BHM due to the agglomeration of nanoparticles in the polymer blend matrix. The lowest activation energy value (0.049 × 10−4 eV) is also exhibited by 7 wt% BHM nanocomposites. Furthermore, the electrical properties of both CG/PPy and CG/PPy/BHM nanocomposites exhibited a temperature-dependent behavior, progressively increasing until reaching maximum values. This study suggests that such bio-based polymer dielectrics could be promising materials for various applications, offering enhanced thermal and electrical properties through careful control of nanofiller content and dispersion.

Enhanced thermal stability and mechanical performance of epoxy resin with amine-terminated aromatic amide oligomer: unveiling the ring-opening curing phenomenon

Enhanced thermal stability and mechanical performance of epoxy resin with amine-terminated aromatic amide oligomer: unveiling the ring-opening curing phenomenon

Study on the Thermal Safety of 3,7‐Dinitro‐1,3,5,7‐Tetraazabicyclo[3.3.1]nonane Synthesized by Nitrolysis of Hexamine

AbstractThe thermal flow curves of the nitrolysis for the synthesis of 3,7‐dinitro‐1,3,5,7‐tetraazabicyclo[3.3.1]nonane (DPT) from hexamine in the presence of different amounts of acetic anhydride were obtained using reaction calorimetry. The maximum heat release rates during the feeding process, the corresponding maximum adiabatic temperature rises, and the Maximum Temperature of the Synthesis Reaction (MTSR) were determined, respectively. The thermal stability of the reaction product DPT and the reaction mixture was analyzed, and data on their thermal decomposition characteristics were obtained. The thermal decomposition kinetic model was utilized to simulate the stability under adiabatic conditions. TD24 (The temperature corresponding to the time required to reach the maximum reaction rate under adiabatic conditions for 24 hours) of the reaction mixture was calculated as 69.65°C. According to the thermal hazard parameters of the reaction, the process's hazard level under various acetic anhydride addition conditions was determined to be level 5 using the cooling failure scenario method.

Revealing the Hygroscopic Behavior of Ultrahigh Nitrogen Content Cyclo‐Pentazolate Salts

AbstractThree representative cyclo‐pentazolate salts including N2H5+N5−, NH3OH+N5− and NH4+N5−, are highly favored for their ultrahigh nitrogen content (80–96%). However, their ambiguous nature has severely restricted the application exploration. Herein, the relationships between humidity and moisture content of salt were established by quantitative analysis. Among the three salts, the hygroscopic ability has the following order: NH3OH+N5−>NH4+N5−>N2H5+N5−. Especially in the range of 40% RH −60% RH, the NH3OH+N5− has a high sensitivity to water, and the absorbed moisture content can be as high as 20.8% at 60% RH. When the relative humidity exceeds 60% RH, the hygroscopic rate of NH3OH+N5− rises sharply, at 80% RH, NH3OH+N5− will absorb excess moisture and turns into liquid form. After treating NH3OH+N5− at 40% RH, the very sensitive friction sensitivity (FS) and impact sensitivity (IS) of dried NH3OH+N5− (FS=20 N, IS=2 J) will change into insensitive salt (FS>360 N, IS>40 J). The higher moisture content in NH3OH+N5−, the lower the thermal stability, its thermal decomposition temperature (103.22°C) is 3.24°C lower than that of dry salt (106.46°C) at 75% RH (moisture content is 30.2%). The other two salts N2H5+N5− and NH4+N5− have the similar properties. Molecular dynamics simulation was further applied to explain the strong hygroscopicity of salts.

Prediction of the thermal-physical properties of amorphous nickel alloys Ni2B, Ni44Nb56, Ni62Nb38 according to component data

The replacement of traditional materials with amorphous alloys and the operation of products made from them are determined by the structural, temporal and temperature stability of disordered environments. In particular, the thermal stability of an amorphous alloy directly depends on its thermophysical characteristics. Therefore, the article demonstrates the applicability of the rule of mixing components and the use of their data on thermophysical properties in the crystalline state to evaluate similar characteristics of alloys from the metal – metalloid and transition metal – transition metal groups in the amorphous phase. It has been established that for the transition metal – transition metal group, the assessment of the heat capacity of amorphous nickel alloys gives a better approximation to the experimentally established values than for an alloy from the metal – metalloid group. The reasons for the discrepancy between the assessment and experimental data for an alloy from the metal – metalloid group are possibly the covalency of the atomic bonds in contrast to the metallic bond for alloys from the transition metal – transition metal group, the smaller size of the metalloid atoms, its greater mobility and the effect on the refinement of alloy grains. The possibility of an amorphous alloy inheriting some properties of one of the components is indicated, which requires experimental verification.

Enhancing thermal stability and electrical conductivity performance of silica aerogel via graphene oxide integration

Enhancing thermal stability and electrical conductivity performance of silica aerogel via graphene oxide integration

Pyrene‐Functionalized Silicon Hybrid Porous Polymer for an Efficient Adsorption of Dyes

AbstractPyrene‐functionalized silicon hybrid porous polymer (TAPPy‐HPP). The hybrid polymer was successfully prepared via a Schiff base reaction using tetra(4‐aminophenyl)pyrene (TAPPy) and tetra(4‐formylphenyl)silane (TFS) as the building blocks.. This hybrid polymer was characterized using IR, solid‐state 13C and 29Si NMR, and elemental analysis. Its morphology was analyzed by PXRD and SEM. Thermal analysis using Thermal analysis using TGA shows that the synthetic polymer has greater thermal stability than its monomers at a temperature of 5 % weight loss (Td5 %) of 392 °C. Although TAPPy‐HPP has a Brunauer‐Emmet‐Teller surface area of 45.4 m2 g−1, it adsorbed dyes with high efficiency, particularly the anionic dye Congo Red (CR), with an adsorption capacity of up to 358 m2 g−1. Moreover, TAPPy‐HPP showed excellent recycling and regenerative properties. This polymer is a promising candidate for a fluorescent chemical sensor for the absorption of dyes due to its exceptional physiochemical stability and intense luminescence.