Thermal Properties Research Articles

The Influence of the Addition of Basalt Powder on the Properties of Foamed Geopolymers.

Geopolymers are binder materials that are produced by a chemical reaction between silica or aluminum compounds with an alkaline activating solution. Foamed geopolymer materials are increasingly being cited as a viable alternative to popular organic insulation materials. Since the foaming process of geopolymers is difficult to control, and any achievements in improving the performance of such materials are extremely beneficial, this paper presents the effect of the addition of basalt powder on the properties of foamed geopolymers. This paper presents the results of physicochemical studies of fly ash and basalt, as well as mechanical properties, thermal properties, and structure analysis of the finished foams. The scope of the tests included density tests, compressive strength tests, tests of the thermal conductivity coefficient using a plating apparatus, as well as microstructure tests through observations using light and scanning microscopy. Ground basalt was introduced in amounts ranging from 0 to 20% by mass. It was observed that the addition of basalt powder contributes to a reduction in and spheroidization of pores, which directly affect the density and pore morphology of the materials tested. The highest density of 357.3 kg/m3 was characterized by samples with a 5 wt.% basalt powder addition. Their density was 14% higher than the reference sample without basalt powder addition. Samples with 20 wt.% basalt addition had the lowest density, and the density averaged 307.4 kg/m3. Additionally, for the sample containing 5 wt.% basalt powder, the compressive strength exceeded 1.4 MPa, and the thermal conductivity coefficient was 0.1108 W/m × K. The effect of basalt powder in geopolymer foams can vary depending on many factors, such as its chemical composition, grain size, content, and physical properties. The addition of basalt above 10% causes a decrease in the significant properties of the geopolymer.

Magnetron-Sputtered Long-Term Superhydrophilic Thin Films for Use in Solid-State Cooling Devices

Pulse-magnetron-sputtered long-term superhydrophilic coatings have been synthesized to functionalize the surfaces of solid-state cooling devices, e.g., electrocaloric heat pumps, where not only a complete wetting of the surface by a fluid is intended, but also fast wetting and dewetting processes are required. The coatings consist of a (Ti,Si)O2 outer layer that provides lasting hydrophilicity thanks to the mesoporous structure, followed by an intermediate WO3 film that enables the reactivation of the wettability through visible light irradiation, and a W underlayer which can work as a top electrode of the electrocaloric components thanks to its suitable electrical and thermal conductivity properties. Process parameter optimization for each layer of the stack as well as the influence of the microstructure and composition on the wetting properties are presented. Finally, water contact angle measurements, surface energy evaluations, and a contact line dynamics assessment of evaporating drops on the coatings demonstrate that their enhanced wetting performance is attributed not only to their intrinsic hydrophilic nature but also to their porous microstructure, which promotes wicking and spreading at the nanometric scale.

Synthesis, growth, structural, thermal, electrical and optical properties of organic NLO: N’ methyl urea oxalic acid

Synthesis, growth, structural, thermal, electrical and optical properties of organic NLO: N’ methyl urea oxalic acid

Thermal modal analysis of hypersonic composite wing on transient aerodynamic heating

Considering the influence of thermal stress and material property variations, this study employs the Navier–Stokes equations and Fourier heat conduction law to establish a semi-implicit time-domain numerical analysis method for hypersonic aerothermal-structural coupling. Study the temporal variation pattern of different regions of the composite material wing under aerodynamic heating. Using the obtained transient temperature field of the wing, the thermal modal of the wing at different time points is calculated using the finite element method. Additionally, it conducts an analysis and discussion on the factors influencing the thermal modal. Composites can be effectively utilized as thermal protection materials for aircraft. During the aerodynamic heating process, the leading edge temperature reaches thermal equilibrium first, followed by the trailing edge, and the belly plate experiences a slower thermal response. Temperature rise significantly affects higher-order modes, with the change in material properties during the early stages of heating being the dominant factor. This leads to a faster decrease in natural frequency. As heat conduction progresses, the influencing factors of thermal stresses gradually increase, and the natural frequency decreases slowly or even rises.

Modeling of nanoblood flow in an artery in presence of eco-friendly and biocompatible hybrid nanoparticles

Transferring biological fluid through arteries is a topic that has garnered serious interest in recent times, especially when it pertains to applications such as drug delivery. In our body, arteries serve as the primary conduits for blood flow and this study aims to model the blood flow in this situation. The working fluid is essentially pure blood, which acts as a base fluid, supplemented with nanoparticles of Titanium Dioxide (TiO2) and Gold (Au). Nanoparticles could change the thermal and rheological properties of blood which might be particularly advantageous for ensuring smoother flow or optimal distribution of drug molecules within the bloodstream. In the present work, a porous channel is considered with parallel walls that exhibit varying permeability on boundaries. Such a design enables the nanoblood to enter and exit the channel, mimicking certain natural processes like transvascular fluid exchange. Additionally, the variable height of the channel that expands and squeezes uniformly could be reminiscent of the pulsatile nature of blood flow seen in our arteries due to heartbeats. To understand the dynamics of this hybrid nanoblood flow, the governing equations are converted into a set of nonlinear ordinary differential equations using the similarity transformation approach. For solving these transformed equations, the research harnesses the BVP4C built-in function in MATLAB software. Through this computational approach, the research provides insights into the velocity and temperature profile of the fluid, the distribution of normal pressure, wall shear stress, and the Nusselt number concerning various parameters. The findings of the present study can be significant and useful in biological sciences and technologies and the detailed results are presented completely in the article’s body.

Evaluation of Edible Coatings from Components from Chlorella vulgaris and Comparison with Conventional Coatings

The present customer demand for ready-to-eat food items with higher nutritious value and longer shelf life necessitates creative solutions. An edible coating is a sustainable packaging solution that can prevent food deterioration and preserve food quality. Proteins, starch, and the addition of plasticizers are used to create edible coatings. The aim of this study was to develop coating solutions that can best preserve food using isolated starch and proteins from Chlorella vulgaris, and then compare them to coatings that comprise conventional ingredients like chitosan and starch. A number of criteria pertaining to the coatings’ mechanical, optical, thermal, and physical properties were tested. The alternative coatings performed just as well as the conventional ones, with the protein algal coating exhibiting the best thermal, optical, and physical qualities. The food product that needs to be coated can determine which coating is ideal. In conclusion, edible coatings derived from Chlorella vulgaris offer a sustainable solution to preserve ready-to-eat food items, showcasing comparable performance to conventional coatings.

Thermal and Flow Properties of Jeffrey Fluid Through Prabhakar Fractional Approach: Investigating Heat and Mass Transfer with Emphasis on Special Functions

Thermal and Flow Properties of Jeffrey Fluid Through Prabhakar Fractional Approach: Investigating Heat and Mass Transfer with Emphasis on Special Functions

Cellulose Nanocrystals and Lignin Nanoparticles Extraction from Lemna minor L.: Acid Hydrolysis of Bleached and Ionic Liquid-Treated Biomass.

Using biomass to develop and obtain environmentally friendly and industrially applicable biomaterials is increasingly attracting global interest. Herein, cellulose nanocrystals (CNCs) and lignin nanoparticles (LNPs) were extracted from Lemna minor L., a freshwater free-floating aquatic species commonly called duckweed. To obtain CNCs and LNPs, two different procedures and biomass treatment processes based on bleaching or on the use of an ionic liquid composed of triethylammonium and sulfuric acid ([TEA][HSO4]), followed by acid hydrolysis, were carried out. Then, the effects of these treatments in terms of the thermal, morphological, and chemical properties of the CNCs and LNPs were assessed. The resulting nanostructured materials were characterized by using Fourier-transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) spectroscopy, thermo-gravimetric analysis (TGA), and scanning electron microscopy (SEM). The results showed that the two methodologies applied resulted in both CNCs and LNPs. However, the bleaching-based treatment produced CNCs with a rod-like shape, length of 100-300 nm and width in the range of 10-30 nm, and higher purity than those obtained with ILs that were spherical in shape. In contrast, regarding lignin, IL made it possible to obtain spherical nanoparticles, as in the case of the other treatment, but they were characterized by higher purity and thermal stability. In conclusion, this research highlights the possibility of obtaining nanostructured biopolymers from an invasive aquatic species that is largely available in nature and how it is possible, by modifying experimental procedures, to obtain nanomaterials with different morphological, purity, and thermal resistance characteristics.

The effect of replacing molybdenum with vanadium on the tendency to amorphisation, structure and thermal properties of high-entropy alloys of the Fe–Co–Ni–Cr–(Mo,V)–B system

The effect of replacing molybdenum with vanadium on the tendency to amorphisation, structure and thermal properties of high-entropy alloys of the Fe–Co–Ni–Cr–(Mo,V)–B system

A short banana fiber—PLA filament for 3D printing: Development and characterization

AbstractThis study aims to develop a 3D printable composite filament using short banana fiber and polylactic acid (PLA). The filament was acquired through a single screw extruder, employing various blending techniques. Various fiber loadings were examined, impacting PLA's mechanical, thermal, and printability properties. The results revealed altered mechanical characteristics, with reduced tensile and flexural properties compared with pure PLA. However, these values are at an acceptable level for non‐structural applications. Compared with previous works, the filament developed in the present work is found out to be second strongest among the cellulose fiber‐reinforced PLA filaments. 3D printing with the composite filament encountered no significant issues. A modified mixing method improved mechanical characteristics, although 3D‐printed samples showed deteriorated mechanical characteristics due to poor interfacial bonding. This research introduces an environmentally viable strategy for advancing 3D printing technology by integrating banana fibers into PLA filament. The proposed strategy can be effectively utilized in making cellulose/PLA filaments for 3D printing applications. This innovative approach preserves PLA's natural biodegradability while carefully managing the integration of banana fibers and their potential effects on mechanical properties.Highlights Fiber loading influences mechanical, with minimal impact on thermal properties. Solution casting improved fiber/matrix bonding and filler homogeneity. Plasticizing effect reduces the tensile strength. Modified mixing resulted in even filament diameter and improved tensile properties.

Mechanical recycling process: An alternative for a viable disposal of carbon fiber‐reinforced thermoplastic waste

AbstractConcern for the environment has increased the interest of the automotive and aerospace industries in evaluating the feasibility of mechanical recycling of waste carbon‐fiber‐reinforced polymer composites (CFRP) and waste from protective films used during the transport and storage of thermosetting composites, which are removed and discarded during manufacturing. Therefore, this work aimed to develop a recyclable composite from protective film waste by incorporating carbon fiber/poly(aryl ether ketone) (CF/PAEK) composite particles obtained through grinding in knife mills, followed by an analysis of the particle size distribution. Protective film residues (PEres) were cut to facilitate processing. A mixture of low‐density polyethylene and PEres (50/50) was used as the composite matrix, and 5, 10, 15, and 20 wt% CF/PAEK composite particles were added as the reinforcing agents. Then, these recycled composites were prepared by melt mixing using a twin‐screw extruder and injection molding to obtain standardized samples. Mechanical, thermal, electrical, and electromagnetic properties were evaluated. It was possible to observe that the increase in the addition of CF/PAEK composite particles contributed to a 290% increase in elastic modulus values and a 9.1% increase in Shore D hardness, electrical conductivity, and attenuation of the electromagnetic wave. Furthermore, satisfactory adhesion between filler and matrix contributed to a good interface and reinforcement of the final material.Highlights Mechanical recycling by extrusion of waste from the automotive and aerospace sectors Grinding of carbon fiber/poly(aryl ether ketone) composite waste to be used as filler Protective film waste used as matrix Composites developed with waste with good electrical and electromagnetic properties The addition of thermoplastic composite residues does not affect thermal and mechanical properties

A new nano-sachet manufactured by solution blow spinning to retard ripening of bananas using biodegradable nanostructured polymeric mats emitting 1-methylcyclopropene

The aim of this study was to produce nanostructured poly (lactic acid) (PLA) mats incorporated with the 1-MCP/α-CD complex (F1-MCP) by the solution blow spinning (SBS) technique and to apply them as a nano-sachet emitting 1-MCP in a banana packaging system. The nanofibers that comprise the mats presented uniform morphology with diameters between 157 and 184 nm. Scanning electron microscopy showed that crystals of 1-MCP/α-CD were encapsulated and found on the nanofibers' surface, changing their thermal properties and contact angles. The release of 1-MCP gas from the nano-sachet of nanostructured PLA mats with encapsulated 1-MCP/α-CD was proven based on the delay of banana ripening during storage (21 °C and 90 % RH). Therefore, the nanostructured PLA mats with encapsulated MCP/α-CD, produced by SBS, proved viable and applicable in packaging systems that aim to delay ripening and increase the postharvest shelf life of climacteric fruit, such as bananas.

Exploring the spectral and nonlinear optical properties of phenyl isothiocyanate through density functional theory and molecular docking studies: A comprehensive analysis of a potent biologically active phytochemical

Quantum chemical calculations employing Density Functional Theory (DFT) with 6–31G (d,p) basis sets have yielded valuable insights into the molecular structure, Frontier Molecular Orbitals (FMOs), Mulliken Charges, and Molecular Electrostatic Potential Maps of the phenyl isothiocyanate (PITC) molecule. Spectral analysis of PITC has been conducted including Fourier transform infrared (FTIR), Fourier transform Raman (FT-RAMAN), Nuclear Magnetic Resonance (NMR), and ultraviolet–visible (UV–Vis) spectroscopy by theoretical method. Additionally, global descriptive parameters and thermal properties have also been determined. The Nonlinear Optical characteristic (NLO) has been assessed in the gas phase using the same level of theory. The investigation into toxicity revealed that the studied molecule exhibits drug-like characteristics and is non-toxic. Molecular docking studies have been employed to investigate hydrogen bond interactions, elucidating the minimal binding energy of the compound. The outcomes of the docking studies strongly suggest the significant biological activity of Phenyl Isothiocyanate, emphasizing its potential as a potent phytochemical.

Comparative Investigation of Thermal Properties Improvement of Nano-Enhanced Organic Phase Change Materials

Thermal energy storage (TES) using phase change materials (PCMs) is one of the potential solutions for stockpiling thermal energy and utilizing it for different applications, which results in effective energy usage. The main drawback of organic PCMs in practical applications is poor heat transfer due to low thermal conductivity (TC). Therefore, investigations into nano-enhanced PCMs are being explored to improve their thermophysical properties. In this work, the various thermophysical characteristics of nano-enhanced lauryl alcohol as a PCM were investigated using carbon-based and metallic nanoparticles. The results indicated that the addition of nanoparticles improved its thermal properties and affected other physical properties, such as viscosity. The latent heat was degraded with the addition of nanoparticles. The results revealed that by adding MWCNTs and CuO nanoparticles, a maximum of 82.6% and 49.6% improvement in TC was achieved, respectively. The maximum drop in latent heat during melting and freezing for the PCM with MWCNTs was about 10.1% and 9.3%, respectively, whereas for the PCM with CuO, they were about 11% and 10.3%, respectively. The lowest supercooling for the PCM with MWCNTs and CuO nanoparticles was 8.6 and 8.3 °C, respectively. The present work confirms that nano-enhanced PCMs can be a potential material for storing thermal energy for various applications.

Enhancing performance: insights into the augmentation potential of acrylonitrile butadiene styrene/boron nitride composites

Abstract This work aims to investigate the morphological, mechanical and thermal characteristics of boron nitride (BN)-reinforced acrylonitrile-butadiene styrene (ABS) composites. ABS and ABS/BN composites with a maximum BN loading up to 8 wt% were developed using two-roll mill followed by compression molding. Scanning electron microscopy (SEM) images presented interlinking of BN flakes in the dimple texture of ABS. A modest decrease in tensile properties was observed for the composites. The tensile strength and impact strength for the ABS/BN8 specimen were lowered by 4.7 and 81.7 %, respectively. On the other hand, hardness increased by 3.39 % for ABS/BN8 composite. The interaction effect of BN in the ABS matrix on the thermal properties was assessed using thermo-gravimetric analysis (TGA). An enhancement in the thermal-stability was observed for BN incorporated ABS. There is a modest shift in glass transition (T g) temperature to a higher value for the ABS/BN composites.

Mechanical and thermal characterization of elastomer modified polypropylene hybrid composites reinforced with hazelnut shell and wollastonite fillers

AbstractThe demand for sustainable and recyclable materials in industrial applications has led to a surge in interest in green composites, particularly those incorporating natural fillers derived from agro‐food industry waste. This study investigates the mechanical and thermal properties of polypropylene (PP) hybrid composites filled with hazelnut shell and wollastonite, along with the effect of styrene‐ethylene/butylene‐styrene (SEBS) and SEBS‐g‐maleic anhydride (SEBS‐g‐MA) compatibilizers. Various characterization techniques, including tensile, flexural, and impact tests, as well as differential scanning calorimetry (DSC), thermogravimetry (TGA), and scanning electron microscopy (SEM) analyses, were employed to evaluate the composites. Results demonstrate that the addition of wollastonite significantly improves mechanical properties, while hazelnut shell filler affects thermal behavior and stability. SEBS and SEBS‐g‐MA compatibilizers enhance impact resistance; however, they lead to a decrease in other mechanical properties. DSC and TGA analyses demonstrate changes in crystallization behavior and thermal stability due to filler and compatibilizer incorporation. SEM microstructure images show the distribution of SEBS and SEBS‐g‐MA within the composite structure, affecting mechanical and thermal properties. Overall, this study highlights the importance of filler selection, compatibilizer addition, and their distribution in attaining desired properties for industrial applications. Future research should focus on optimizing formulations for specific uses and assessing long‐term performance under real‐world conditions.

Understanding the microstructure evolution of carbon-doped Sb2Te3 phase change material for high thermal stability memory application

The Sb2Te3 phase change material shows a growth-dominated crystallization mechanism with fast phase transition but poor thermal stability of the amorphous state. This work investigated the effects of carbon doping on the thermal stability, microstructure, and electrical properties of the Sb2Te3 material. The 10-year data retention temperature of the material increased to ∼147.3 °C and the size of the grains was limited to ∼10 nm by carbon doping. The formation of the C cluster upon crystallization was found at the grain boundaries, which was accelerated as the temperature increased due to the break of the Sb–C bonds. The memory device based on the carbon-doped Sb2Te3 material exhibited a switching speed of 15 ns and an endurance of ∼105 cycles with a resistance ratio of more than two orders of magnitude. This work suggests that the carbon-doped Sb2Te3 material is a promising candidate for memory applications that require high thermal stability, fast speed, and high endurance.

Evaluation of Energy Density in Hexadecane Phase Change Emulsions in Comparison to Water

The development of energy-dense, thermomechanically stable, and low-viscous phase change emulsions (PCMEs) is proposed as an alternative thermal energy storage solution for building air conditioning. A set of oil-in-water (O/W) nanoemulsions with hexadecane concentration varied between 10, 20, 25, 30, 35, and 40 wt. % is prepared and characterized with respect to their physical, thermal, and rheological properties. The storage characteristics are evaluated in terms of storage density, phase transition behaviour, supercooling, and dynamic viscosity. A systematic comparison in terms of energy density between the PCMEs and water is carried out at different temperature conditions. For this purpose, the storage break-even temperature TBE is proposed as a novel parameter to determine suitable operating temperature ranges and cycling conditions. The cycle stability is evaluated by rheological measurements, applying thermomechanical loads to the samples for a high number of cycles. According to the results, the energy density of the PCMEs is always higher than that of water, when the minimum temperature used for the cycling is below the storage break-even temperature. The emulsion with 30 wt. % hexadecane fraction is considered particularly promising, thanks to its high stability when exposed to thermomechanical stress, relatively low viscosity between 10 and 22 mPa s (0–30°C), and a storage density of 98 MJ/m3 within a cycling temperature range of 12 K.

Experimental investigations of temperature-sensitive shape memory polymer composites for 4D printing

Shape memory polymers (SMPs) and their composites (SMPCs) have emerged as popular materials in a variety of industries due to their unique properties of shape-changing behavior in response to external stimuli. The inclusion of reinforcement may modify the SMPs to enhance their thermal and shape memory properties. Different types of bio ceramics have already been used to alter the thermal and shape memory behavior of SMPs. However, using bioactive glass (BG) as filler to modify these properties has not yet been explored. Despite the significant advantages that shape-memory polymers (SMPs) offer when combined with 3D/4D printing technology, their potential in 3D printing has been explored only to a limited extent. This work created a solvent-based 4D-printed temperature-sensitive shape memory polymer composites (SMPCs) system using polylactic acid (PLA) and bioactive glass (BG). The influence of BG on the thermal as well as shape-memory capabilities of composites was further examined. An increase in the degree of crystallinity and viscoelastic characteristics of PLA/BG composites led to improved shape memory properties, like shape fixity and shape recovery. These findings suggest the potential for using the developed SMPC printed through 4D printing technology, to develop complex shapes for self-foldable structures and smart biomedical devices in the future.

Aging-Induced Changes in Popping, Structural, Functional, Thermal, and Crystalline Properties of Roasted Makhana Seeds

Aging-Induced Changes in Popping, Structural, Functional, Thermal, and Crystalline Properties of Roasted Makhana Seeds