Tensile Stress Research Articles

Influence of Strain Rate on Barkhausen Noise in Trip Steel.

This paper deals with Barkhausen noise in Trip steel RAK 40/70+Z1000MBO subjected to uniaxial plastic straining under variable strain rates. Barkhausen noise is investigated especially with respect to microstructure alterations expressed in terms of phase composition and dislocation density. The effects of sample heating and the corresponding Taylor-Quinney coefficient are considered as well. Barkhausen noise of the tensile test is measured in situ as well as after unloading of the samples. In this way, the contribution of external and residual stresses on Barkhausen noise can be distinguished in the direction of tensile loading, as well as in the transversal direction. It was found that the in situ-measured Barkhausen noise grows in both directions as a result of tensile stresses and the realignment of domain walls. The post situ-measured Barkhausen noise drops down in the direction of tensile load due to the high opposition of dislocation density at the expense of the growing transversal direction due to the prevailing effect of the realignment of domain walls. The temperature of the sample remarkably grows along with the increasing strain rate which corresponds with the increasing Taylor-Quinney coefficient. However, this effect plays only a minor role, and the density of the lattice imperfection expressed especially in terms of dislocation density prevails.

Seismic Response Analysis of a New Staggered Story Isolated Structure Under Three-Dimensional Earthquakes

The new staggered story isolated structure is a new isolated structure developed from base-isolated structures and inter-layer isolated structures. This paper establishes a model of the new staggered story isolated structure and analyzes its seismic response under three-dimensional earthquakes. In cases where the tensile stress and compressive stress of the isolated bearings exceed the limit, a three-dimensional isolated bearing is introduced and compared with the traditional horizontal isolated bearing. The results indicate that the seismic response of the new staggered story isolated structure under three-dimensional earthquakes is more obvious than that under one-dimensional and two-dimensional earthquakes. After using three-dimensional isolated bearings, the seismic response of the structure is mitigated, and the seismic performance is enhanced, the tensile stress and compressive stress of the isolated bearings meet the specification requirements. This paper serves as a valuable reference for designing new staggered story isolated structures under three-dimensional earthquakes.

Microscopic simulation on triaxial compression creep of rockfill based on subcritical crack propagation theory

Over time, natural cracks within particles propagate under tensile stress, leading to the delayed breakage of these particles, which significantly contributes to the time-dependent deformation of rockfill materials. In this study, a delayed strength model for spherical particles with virtual cracks is proposed using subcritical crack propagation theory and validated through indoor single-particle creep tests. Based on the model, particles are represented as ideal spheres in the context of triaxial compression creep simulations for rockfill, with special attention to particle size effects, discreteness, and temporal factors. The combined influence of long-term strength and maximum contact force is crucial in determining the delayed particle breakage. Comparative analysis with indoor triaxial creep tests demonstrates that the Discrete Element Method (DEM) simulations accurately model the creep deformation phenomena related to delayed particle breakage in rockfill. Furthermore, statistical analysis indicates that a minor fraction of delayed particle breakage has a negligible impact on the temporal distribution of the Normalized Maximum Contact Force (NMCF).

Effect of Thermal Processing on the Structural and Magnetic Properties of Epitaxial Co2FeGe Films.

The structure and magnetic properties of epitaxial Heusler alloy films (Co2FeGe) deposited on MgO (100) substrates were investigated. Films of 60 nm thickness were prepared by magnetron co-sputtering at different substrate temperatures (TS), and those deposited at room temperature were later annealed at various temperatures (Ta). X-ray diffraction confirmed (001) [110] Co2FeGe || (001) [100] MgO epitaxial growth. A slight tetragonal distortion of the film cubic structure was found in all samples due to the tensile stress induced by the mismatch of the lattice parameters between Co2FeGe and the substrate. Improved quality of epitaxy and the formation of an atomically ordered L21 structure were observed for films processed at elevated temperatures. The values of magnetization increased with increasing TS and Ta. Ferromagnetic resonance (FMR) studies revealed 45° in-plane rotation of the easy anisotropy axis direction depending on the degree of the tetragonal distortion. The film annealed at Ta = 573 K possesses the minimal FMR linewidth and magnetic damping, while both these parameters increase for another TS and Ta. Overall, this study underscores the crucial role of thermal treatment in optimizing the magnetic properties of Co2FeGe films for potential spintronic and magnonic applications.

Mechanical Properties of Novel Hybrid Bamboo Fibre/Aluminium Mesh Reinforced Polymer Composite

Bamboo fibres are one of the sustainable lignocellulosic resources explored for polymer composites in recent years. Research has shown that bamboo fibres have the potential to be used in a variety of critical applications. Nevertheless, bamboo fibres are susceptible to thermal and hygroscopic loads, and their mechanical properties are limited by the unequal interfacial strength and varying fibre dimensions. Implementing hybrid procedures or incorporating alternative materials, such as aluminium metal, is strongly advised to address this issue. Thus, this study investigates the tensile and flexural performances of the hybrid bamboo fibre/aluminium expanded mesh-reinforced polymer composites. The composites were fabricated using epoxy resin reinforced with bamboo fibre, and an aluminium expanded mesh sheet was constructed using a vacuum infusion process utilising various stacking sequences and mesh sizes. The test findings indicated that the composite material exhibited tensile stress values ranging from 27 to 34 MPa and a corresponding tensile strain value between 1.1% and 1.6%. The flexural strength and strain values were measured within the range of 44 Mpa to 59 Mpa and 2.2% to 3.2%, respectively. ANOVA analysis showed that both stacking sequences and mesh size significantly affected the tensile performances of the composites, while only stacking sequences affected the flexural performance significantly. Overall, a hybrid composite of bamboo fibre and aluminium mesh is well-suited as a substitute material in industries requiring exceptional mechanical properties.

Biomechanical effects of functional clear aligners on the stomatognathic system in teens with class II malocclusion: a new model through finite element analysis

ObjectivesThe Functional Clear Aligner (FCA) is a novel orthodontic appliance designed for the treatment of Class II malocclusion with mandibular retrognathia in adolescents. The aim of this study was to investigate the biomechanical characteristics of the masticatory muscles, jawbone, and temporomandibular joint (TMJ) during mandibular advancement using either FCA or Class II elastics combined with clear aligner (Class II elastics) through finite element analysis.Materials and methodsA 3D finite element model of the ‘muscle-jawbone-TMJ-appliance’ system was constructed based on CBCT and MRI images of a boy with skeletal Class II malocclusion. Masticatory muscles included masseter, temporal, medial pterygoid, and lateral pterygoid muscles. The TMJ consists of the temporal bone’s glenoid fossa, disc, and mandibular condyle. To observe the biomechanical characteristics of the muscles and TMJ during orthodontic appliance wearing and the retention phase, two different protocols were used: Model 1: The mandibular advancement using FCA; Model 2: The mandibular advancement using Class II elastics.ResultsThe FCA group produced greater and more coordinated masticatory muscle forces compared to the Class II elastics group. Temporal and masseter muscles exhibited the most pronounced variation in muscle strength during mandibular advancement. The FCA group exhibited greater TMJ region stress compared to the Class II elastics group. Interestingly, the stress on the articular discs in both models decreased over time. Tensile stresses were observed in both the condyle and the posterior region of the articular fossa.ConclusionDuring skeletal Class II malocclusion treatment, masticatory muscle forces and stress on the TMJ were higher in the FCA group compared to the Class II elastics group. In both models, stress cushioning was provided by the articular disc.

Enhancing the strength of tissue paper through pulp fractionation and stratified forming

Abstract The potential of combining stratified paper forming with pulp fractionation was investigated to improve the balance between low density, which enhances water absorbency and softness, and the dry strength of tissue papers. The selected fractionation approaches allowed us to separate especially stiff, low-fibrillated fibers (A fractions) from flexible, fibrillated fibers containing fines (detached segments of fibers, fibrils, or lamellae fragments) (B fractions). After characterizing the morphological properties of each fiber fraction, 20 g/m2 model papers were produced with and without wet pressing to tune the paper density. At a density of 0.3 g/cm³, the tensile breaking stress of B papers was at least three times higher than that of A papers. The strain at break of B papers was also close to two times higher than that of A papers. Interestingly, bilayer papers A/B exhibited breaking stress values intermediate between those of A and B papers, while native pulp papers, i.e., without fractionation and stratified forming, followed the trend of A papers. Notably, bi-layering the paper improved the breaking stress by up to twice as much without increasing the paper density, which could be highly beneficial in improving the balance of properties in tissue paper grades.

Residual Fatigue Life Estimation of Damaged Welded Structures

This paper presents a finite element modeling procedure to determine of crack growth behaviour of butt welded joints under the subject of load for mode I. This paper presents a computation procedure to determine the ratio of fatigue crack growth in butt welded plates for mode I fracture mechanics loading conditions. The presence of residual stresses in welded structures can significantly affect the material’s resistance to fatigue under cyclic loading. The presence of tensile residual stresses adversely affects the fatigue crack growth rate increased it. Change of microstructure and hardening material as a result of the welding process also has a negative impact on the growth of the crack. Accurate prediction and reliable assessment of the residual stress are important for the structural integrity and residual life assessment of welded parts design. Although there are several techniques for the determination of residual stresses, the finite element method (FEM) is one of the most convenient and useful. This paper presents a finite element modeling procedure to determine of crack growth behaviour of butt welded joints under tensile load for mode I. Keywords: Welding, Residual stress, Residual life, Crack growth, FEM, Butt welded joint

Cryogenic fracturing efficacy in granite rocks: Fracture toughness and brazilian test differences after elevated temperatures and liquid nitrogen exposure

Hot dry rock (HDR) is a significant contingent as a thermal energy source. Due to its low permeability, considerable depth, high temperature (150–650 °C), and high pressure, the stimulation of HDR is challenging. This research work aims to examine the efficacy of cryogenic fracturing on HDR. We performed fracture toughness and indirect tensile stress (Brazilian tests) on granite specimens with three different initial temperatures before exposure to liquid nitrogen (LN2). Fracture toughness tests were implemented on semicircular bend (SCB) specimens containing a pure mode-I fracture, and Brazilian tests were performed with discs. The experimental outcomes show that, overall, both critical load in Brazilian tests and the fracture toughness of LN2-treated specimens of granites both diminished with increasing initial temperature. When the initial temperature exceeded 300 °C (in this instance, 500 °C), the amplitude of thermally induced fractures in granite moderately increased after LN2 treatment, secondary fractures prolonged, and the plastic characteristics increased. Moreover, permeability measurements indicated amelioration with elevated temperatures and subsequent LN2 exposure. SEM analysis showed that an increase in initial temperatures along with LN2 treatment led to further intensified granite microdamage while the quantity and the magnitude of thermal fractures augmented.

Development of craquelure patterns in paintings on canvas

Canvas paintings are layered structures composed of canvas support sized with animal glue, a preparatory layer of the ground, and paint and varnish layers on the top. Preventing or limiting humidity-induced stresses in these structures requires an understanding of the relevant processes and risks. A three-dimensional model of a canvas painting was used to analyse stresses and crack development in the two-layer structure comprised of a glue-sized canvas on a wooden stretcher with a layer of stiff chalk-glue ground representing a pictorial layer in historic canvas paintings. The model was subjected to a large relative humidity fall which induced shrinkage of the glue-sized canvas. The modelling revealed that when a stretcher with flexible wooden bars is considered, high tensile stresses arise in the ground layer at the corners of the painting, and cracks are formed in these areas in the direction perpendicular to the painting’s diagonal. Ratios of critical distances between cracks to the ground layer thickness for which stresses in the midpoints between the cracks dropped to below the level inducing fracture in the material were estimated for various magnitudes of the relative humidity drop and thicknesses of the ground layer. Increasing ground layer thickness limits the hygric response of the sized canvas and makes the paintings less vulnerable to humidity variations. The ratio of stress along the diagonal calculated for painting with one crack to the solution without cracks was described by the double Lorentz function. A simple procedure of calculating stress variations along the diagonal—using the function—on a sequential addition of cracks was developed. Cracks in central parts of canvas painting were found to be induced by permanent cumulative drying shrinkage of the oil-based paints and grounds due to the evolution of the molecular composition of the oil binder. The outcome of the modelling indicated that the risk of cracking of the pictorial layers in canvas paintings due to drops in ambient relative humidity was small.

Exploring residual stress analysis in the machining of hypoeutectic high chromium white cast iron alloys through the hole-drilling method

Abstract High chromium white cast irons (HCWCIs), ASTM A352, Type A and Class III, i.e., 25%Cr iron in as-cast condition consists of proeutectic austenite (γ-Fe), transformed martensite (α-Fe) and discontinuous Cr-rich, i.e., M7C3/ (Cr, Fe)7C3 type of carbides, which are hard and brittle in nature. Fully annealed thermal treatment was performed to improve iron’s machinability leading to fully pearlitic matrix with minor retained γ-Fe content. Eutectic (Cr, Fe)7C3 type of carbides are not affected by heat treatment processes. Resulting from corresponding manufacturing process, the magnitude and distribution of residual stresses (RSs) in as-cast and after machining were measured using hole-drilling method (HDM), as they are known to be harmful to corrosion and fatigue resistance. Furthermore, general metallurgical material characterisation was performed in as-cast and heat-treated conditions. As a result, this study revealed hardness variation, 547 and 555BHN in as-cast as compared to 327BHN in heat-treated condition. Furnace and actual cast component chemical analysis revealed a slight variation, especially between carbon (C) and chromium (Cr). Furthermore, eutectic type of carbides and precipitated secondary, i.e., (Cr, Fe)23C6 type of carbides within fully pearlitic matrix with minor amounts of retained γ-Fe were detected within the dominant matrix, i.e., pearlitic matrix in as-annealed condition. Detected magnitude and distributions of RSs on heat-treated sample resulted in higher tensile stresses in the surface and compressive in the interior as compared to sample in as-cast condition. Thus, this study was successfully in measuring RSs in as-cast and upon machining of hypoeutectic irons of HCWCI alloys using HDM.

Influence of phase composition and stress on the corrosion behavior of metastable β titanium alloy Ti-5Mo-5V-6Cr-3Al in 15 wt% HCl solution

Immersion experiments, electrochemical tests under different tensile stresses, and microstructure observation using SEM, EBSD, and TEM were carried out on three Ti-5Mo-5V-6Cr-3Al alloys with different phase compositions in 15 wt% HCl solution to clarify the effects of the phase compositions and stresses on the corrosion behavior of metastable β-titanium alloys in acidic media. The microstructure with only primary α-phase on the β-matrix (No. M1) presents the smallest corrosion current density and the highest corrosion potential, indicating relatively the best corrosion resistance; the microstructure with both primary and secondary α-phase on the β matrix (No. M2) has moderate corrosion resistance; and the microstructure with secondary α-phase precipitated on the β matrix (No. M3) has the relatively poorest corrosion resistance. The results of the immersion experiments show the same regularity as the electrochemical tests. The corrosion resistance of all three microstructures decreases as the degree of stress loading increases. The apparently small amount of α-phase content in M1 is the reason for the difference in corrosion resistance between M2 and M3, M3 alloys with larger average grain sizes exhibit better corrosion resistance than M2 alloys. Under tensile loading, disruption of the surface passivation film and pitting promoted by dislocation slip are the main reasons for the reduction in the corrosion resistance of the alloy.

Machining mechanism of CoCrFeNiAlX high entropy alloys via ultrasonic elliptical vibration cutting

Abstract This study investigates the micro-cutting mechanism of CoCrFeNiAl X high entropy alloys, focusing on the impact of amplitude, vibration frequency, cutting depth, and the Al element content. The mechanical response of the material is analyzed using simulation methods for both conventional cutting and ultrasonic elliptical vibration assisted cutting (UEVAC). The results show that under different vibration parameters and cutting depth, the cutting temperature produced by UEVAC is significantly higher than that of conventional cutting temperature. When the Y-axis amplitude is reduced from 90 μm to 30 μm, the cutting temperature is reduced by 50%. In addition, the cutting temperature is positively correlated with the Al content, and when the molar ratio is 20%, the cutting temperature is about 2.1 times that of 13%. While keeping the cutting parameters unchanged, the cutting force generated by UEVAC is significantly reduced compared to conventional cutting. It is worth noting that when the X-axis amplitude is 40 μm, the Y-axis amplitude is 90 μm, and the vibration frequency is 25 KHz, the cutting force of UEVAC is the smallest, which is only about 13% of the conventional cutting force. With the increase of the mole ratio of aluminum in the high entropy alloy, when the mole ratio of aluminum increases from 0% to 13%, the cutting force begins to decrease by about 33%. However, when the molar ratio increases from 13% to 20%, the cutting force increases by about 214%. On the surface of the workpiece (within the range of 0–3 μm from the machining surface), the residual stress generated by UEVAC is mainly manifested as compressive stress or tensile stress, which is significantly less than the residual stress generated by conventional cutting. The relation of residual compressive stress of workpiece under different aluminum content is Al1 > Al0.6 > Al0.

Study on anti-reflection of deep soft and high gas coal seam floor by deep hole controlled blasting

Addressing the practical challenges of difficult drilling for blasting-induced permeability enhancement in deep, soft, and high-gas coal seams, where fractures remain underdeveloped and prone to re-compaction, this study proposes blasting operations within the floor strata. This approach aims to enhance the permeability of soft coal seams, thereby extending the duration of effective gas extraction. A bidirectional loading gas–solid coupling blasting simulation system was established in the laboratory, enabling multi-faceted analysis of experimental models through macroscopic crack patterns, internal damage mechanisms, and strain data of coal and rock masses. Comparative experiments were conducted, contrasting various control hole spacings with conventional blasting techniques. The findings reveal that as the blasting stress wave traverses the control hole walls, tensile stress waves are reflected, facilitating crack propagation. The guiding effect of the control holes and the spatial compensation they provide significantly increase the extension distance of explosion-induced cracks, resulting in directional failure of the test specimens and heightened damage in the far field of the blast. After the blasting process, the arrangement of control holes can result in an increase of up to 133% in damage to the coal seam and a reduction of up to 167% in damage to the floorboard compared to the model without control holes. Notably, when the control holes are proximal to the coal-rock interface, the near-end coal body experiences the most pronounced effects, with peak damage and tensile strain in the d = 20 mm model being 1.93 and 1.79 times higher, respectively, than those in models without control holes. Conversely, for control holes located further from the interface, the distal coal body experiences the greatest influence, exhibiting 1.53 and 1.55 times higher peak damage and tensile strain, respectively, in the d = 80 mm model compared to uncontrolled counterparts. Field observations at the C13 coal seam of a mine within the Huainan mining area corroborate these findings, where the volume of gas extraction and its concentration experienced a rapid increase following blasting and penetration enhancement. Optimum permeability enhancement occurs when the blasting hole is situated 4 m from the extraction point, resulting in a 131% increase in gas extraction purity from 0.15 × 10–3 m3/min to 1.97 × 10–3 m3/min. Furthermore, gas concentration soars by 373%, from 5.86% to 21.86%. These research outcomes offer valuable insights and hold considerable reference significance for blasting-induced permeability enhancement in deep, soft, and high gas coal seams.

Poly(HEMA-co-MMA) Hydrogel Scaffold for Tissue Engineering with Controllable Morphology and Mechanical Properties Through Self-Assembly.

Poly(2-hydroxyethyl methacrylate) (PHEMA) has been widely used in medical materials for several decades. However, the poor mechanical properties of this material have limited its application in the field of tissue engineering. The purpose of this study was to fabricate a scaffold with suitable mechanical properties and in vitro cell responses for soft tissue by using poly(HEMA-co-MMA) with various concentration ratios of hydroxyethyl methacrylate (HEMA) and methyl methacrylate (MMA). To customize the concentration ratio of HEMA and MMA, the characteristics of the fabricated scaffold with various concentration ratios were investigated through structural morphology, FT-IR, mechanical property, and contact angle analyses. Moreover, in vitro cell responses were observed according to the various concentration ratios of HEMA and MMA. Consequently, various morphologies and pore sizes were observed by changing the HEMA and MMA ratio. The mechanical properties and contact angle of the fabricated scaffolds were measured according to the HEMA and MMA concentration ratio. The results were as follows: compressive maximum stress: 254.24-932.42 KPa; tensile maximum stress: 4.37-30.64 KPa; compressive modulus: 16.14-38.80 KPa; tensile modulus: 0.5-2 KPa; and contact angle: 36.89-74.74°. In terms of the in vitro cell response, the suitable cell adhesion and proliferation of human dermal fibroblast (HDF) cells were observed in the whole scaffold. Therefore, a synthetic hydrogel scaffold with enhanced mechanical properties and suitable fibroblast cell responses could be easily fabricated for use with soft tissue using a specific HEMA and MMA concentration ratio.

Integrated Control of Thermal Residual Stress and Mechanical Properties by Adjusting Pulse-Wave Direct Energy Deposition.

Directed energy deposition with laser beam (DED-LB) components experience significant residual stress due to rapid heating and cooling cycles. Excessive residual tensile stress can lead to cracking in the deposited sample, resulting in service failure. This study utilized digital image correlation (DIC) and thermal imaging to observe the in situ temporal evolution of strain and temperature gradients across all layers of a deposited 316 L stainless steel thin wall during DED-LB. Both continuous-wave (CW) and pulsed-wave (PW) laser modes were employed. Additionally, the characteristics of thermal cracks and geometric dislocation density were examined. The results reveal that PW mode generates a lower temperature gradient, which in turn reduces thermal strain. In CW mode, the temperature-stress relationship curve of the additive manufacturing sample enters the "brittleness temperature zone", leading to the formation of numerous hot cracks. In contrast, PW mode samples are almost free of cracks, as the metal avoids crack-sensitive regions during solidification, thereby minimizing hot crack formation. Overall, these factors collectively contribute to reduced residual stress and improved mechanical properties through the adjustment of pulsed-wave laser deposition.

Enhanced casein organohydrogel coating with the liquid metal catalyst for electric leather in human-machine interaction

Leather’s durability and multi-level structure make it an excellent substrate for electronics. Integrating leather with modern electronic technology to create electronic leather is becoming increasingly popular. However, significant challenges remain, such as adhering conductive media to leather, their penetration and dispersion, and the complexity of preparation. This study presents a new strategy for fabricating electronic leather by combining leather with a casein-based organic hydrogel using coating chemistry techniques. This hydrogel is simple to prepare and exhibits excellent biocompatibility and self-adhesive properties, offering a promising approach to overcome these challenges. Here, we designed casein-stabilized core-shell liquid metal-based catalysts and utilized acrylamide (AM), 2-acrylamido-2-methylpropane sulfonic acid (AMPs), CNTs, and glycerol (Gly) to achieve in situ organohydrogel formation on leather under mild conditions (60 s, 25 °C). The resulting organohydrogel-coated material exhibits outstanding stretchability (tensile stress: 70.3 kPa, tensile strain: 1491.8 %), rapid response (423 ms), and high sensitivity (GF: 7.67) as a strain sensor. This substrate can be employed in designing flexible wearable electronic gloves, facilitating seamless information interaction between humans and devices. This innovation demonstrates significant potential in enhancing the functionality of leather as a wearable electronic device. Combining leather’s natural properties with cutting-edge organohydrogel technology is promising to revolutionize the wearable electronics industry, potentially creating highly versatile and multifunctional electronic skins.

Highly oriented as-grown beta-phase bismuth oxide for optical MEMS

AbstractReactive sputtering of bismuth has been used to form highly oriented beta-phase Bi2O3 thin films at 120 °C. Notably, the films consist of nearly vertical ~ 50 nm diameter nano-filaments of highly aligned β phase pure bismuth oxide. The optical characteristics of the films include a direct optical bandgap of 3.95 eV at 300 K and nearly negligible optical absorption in the wavelength range from 500 to 3000 nm. Nanoindentation experiments show that the mechanical characteristics of the films include reduced modulus and hardness values of 90 and 4.5 GPa, respectively. As fabricated, the films exhibit tensile stress which in combination with a relatively high refractive index value in the range of 2.4–2.5 makes the realized Bi2O3 films structurally and optically suitable for fabrication of optical microelectromechanical (MEMS) devices with applications in the visible to mid-infrared wavelength region, such as MEMS-based Fabry–Pérot microspectrometers, which is demonstrated through simulations. Graphical Abstract

Evaluation of fatigue damage of structural steel based on attenuation of laser-induced surface acoustic wave

ABSTRACT In this paper, the fatigue damage degree of low-alloy structural steel is evaluated by using the attenuation characteristics of laser-induced surface acoustic wave (SAW) during propagation. Taking the typical structural steel material Q345 as an example, a cracks model of fatigue damage is established, and the finite element method is used to solve the model. The results showed that the attenuation coefficient of SAW can reflect the depth and density of fatigue cracks. The surface measurement experiments of specimens with stress cycles of 0, 50000, 100000, 150000, and 200,000 showed that with the increase of stress cycles, the attenuation coefficient of SAW increases as a whole, indicating that it is feasible to evaluate the fatigue damage degree based on the attenuation of SAW. A method of applying tensile stress to the material to improve the sensitivity of fatigue damage evaluation is proposed. The tensile stress is used to offset the horizontal amplitude of the SAW, keeping the fatigue cracks in an open state and increasing the attenuation coefficient of SAW. The attenuation coefficient measurement experiment shows that this method is feasible.

The Effect of Steel Over Strength Ratio on Structure Behavior

Seismic design of steel building structures according to SNI 7860:2020 determining the necessary strength of structural members based on the expected yield stress, Ry.Fy, and the expected tensile stress, Rt.Fu. However, the values of Ry and Rt in SNI 7860:2020 are not yet based on the testing of steel products in Indonesia and are still based on the provisions in AISC 341-16. This research was conducted by collecting data on steel tensile test results to obtain the over-strength ratio and then modeling the steel frame building using the over-strength steel provisions of SNI 7860:2020 and based on the tensile test results to determine the difference in structural behavior. Based on the tensile test results, WF300 steel has a yield strength ratio (Ry) of 1.78, which is higher than the SNI specification of 1.5, and a tensile strength ratio (Rt) of 1.35, which is higher than the SNI specification of 1.2. Based on pushover analysis, the deviation value at the initial formation of the plastic hinge on Structure A1 (Ry=1.5) in the x-axis direction of 79.352 mm is smaller than Structure B1 (Ry=1.78) by 94.01 mm. This indicates that the plastic hinge of Structure A1 is formed earlier than Structure B1.