Pressure Sensor Technology Research Articles

MXene-Deposited Melamine Foam-Based Iontronic Pressure Sensors for Wearable Electronics and Smart Numpads.

Iontronic pressure sensors hold significant potential to emerge as vital components in the field of flexible and wearable electronics, addressing a variety of applications spanning wearable technology, health monitoring systems, and human-machine interactions. This study introduces a novel iontronic pressure sensor structure based on a seamlessly deposited Ti3C2Tx MXene layer onto highly porous melamine foam as parallel plate electrodes and an ionically conductive electrolyte of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide/thermoplastic polyurethane coupled with carbon cloth as current collecting layers for improved sensitivity and high mechanical stability of more than 7000 cycles. MXene-deposited melamine foam-based iontronic pressure sensors (MIPS) showed a high sensitivity of 5.067 kPa-1 in the range of 45-60kPa and a fast response/recovery time of 28/18ms, respectively. The high sensitivity, high mechanical stability, and fast response/recovery time of the designed sensor make them highly promising candidates for real-time body motion monitoring. Moreover, sensors are employed as a smart numpad for integration into advanced ATM security systems utilizing machine learning algorithms. This research marks a significant advance in iontronic pressure sensor technology, offering promising avenues for application in wearable electronics and security systems.

Effect of Medial Patellofemoral Complex Reconstruction Technique on Patellofemoral Contact Pressure, Contact Area, and Kinematics.

Medial patellofemoral ligament (MPFL) reconstruction is considered by many to be the gold standard to treat lateral patellar instability; however, some investigators have reported good clinical results after isolated medial quadriceps tendon-femoral ligament (MQTFL) reconstruction or a combined MPFL/MQTFL reconstruction. A handful of studies have preliminarily investigated the biomechanical consequences of these various medial patellar stabilizing procedures. Despite this, no existing study has included multiple medial patellofemoral complex (MPFC) reconstructions and assessment of lateral patellar translation at distinct flexion angles. Combined MPFL/MQTFL reconstruction would restore patellofemoral contact areas, forces, and kinematics closest to the native state compared with isolated reconstruction of the MPFL or MQTFL alone. Controlled laboratory study. Ten adult cadaveric knee specimens were prepared and analyzed under 5 different conditions: (1) intact state, (2) transected MPFC, (3) isolated MPFL reconstruction, (4) isolated MQTFL reconstruction, and (5) combined MPFL/MQTFL reconstruction. Patellar tilt, lateral patellar translation, patellofemoral contact forces, and patellofemoral contact areas were measured in each condition from 0° to 80° through simulated knee flexion using a custom servohydraulic load frame with pressure sensor technology and a motion capture system for kinematic data acquisition. The isolated MPFL, isolated MQTFL, and combined MPFL/MQTFL reconstruction conditions produced significantly less lateral patellar tilt compared with the transected MPFC state (P < .05). No statistically significant differences were found when each reconstruction technique was compared with the intact state in patellar tilt, lateral patellar translation, contact forces, and contact areas. All 3 reconstruction techniques (isolated MPFL reconstruction, isolated MQTFL reconstruction, and combined MPFL/MQTFL reconstruction) restored native knee kinematics, contact forces, and contact areas without overconstraint. Isolated MPFL reconstruction, isolated MQTFL reconstruction, and combined MPFL/MQTFL reconstruction all restore patellofemoral stability comparable with the intact MPFC state without the overconstraint that could be concerning for increasing risk of patellofemoral arthritis.

High-Performance Pressure Sensors Based on Shaped Gel Droplet Arrays.

Polymer gel-based pressure sensors offer numerous advantages over traditional sensing technologies, including excellent conformability and integration into wearable devices. However, challenges persist in terms of their performance and manufacturing technology. In this study, a method for fabricating gel pressure sensors using a hydrophobic/hydrophilic patterned surface is introduced. By shaping and fine-tuning the droplets of the polymer gel prepolymerization solution on the patterned surface, remarkable sensitivity improvements compared to unshaped hydrogels have been achieved. This also showcased the potential for tailoring gel pressure sensors to different applications. By optimizing the configuration of the sensor array, an uneven conductive gel array is fabricated, which exhibited a high sensitivity of 0.29 kPa-1 in the pressure range of 0-30kPa, while maintaining a sensitivity of 0.13 kPa-1 from 30 kPa up to 100kPa. Furthermore, the feasibility of using these sensors for human motion monitoring is explored and a conductive gel array for 2D force detection is successfully developed. This efficient and scalable fabrication method holds promise for advancing pressure sensor technology and offers exciting prospects for various industries and research fields.

Miniaturization of an Osmotic Pressure-Based Glucose Sensor for Continuous Intraperitoneal and Subcutaneous Glucose Monitoring by Means of Nanotechnology.

The Sencell sensor uses glucose-induced changes in an osmotic pressure chamber for continuous glucose measurement. A final device shall have the size of a grain of rice. The size limiting factor is the piezo-resistive pressure transducers inside the core sensor technology (resulting chamber volume: 70 µL. To achieve the necessary miniaturization, these pressure transducers were replaced by small (4000 × 400 × 150 nm³) nano-granular tunneling resistive (NTR) pressure sensors (chamber volume: 750 nL). For benchmark testing, we filled the miniaturized chamber with bovine serum albumin (BSA, 1 mM) and exposed it repeatedly to distilled water followed by 1 mM BSA solution. Thereafter, we manufactured sensors with glucose testing chemistry (ConcanavalinA/dextran) and investigated sensor performance with dynamic glucose changes between 0 and 300 mg/dL. Evaluation of the miniaturized sensors resulted in reliable pressure changes, both in the BSA benchmark experiment (30-35 mBar) and in the dynamic in vitro continuous glucose test (40-50 mBar). These pressure results were comparable to similar experiments with the previous larger in vitro sensors (30-50 mBar). In conclusion, the NTR pressure sensor technology was successfully employed to reduce the size of the core osmotic pressure chamber by more than 95% without loss in the osmotic pressure signal.

Carbon Dioxide Sequestration in Low Porosity and Permeability Deep Saline Aquifer: Numerical Simulation Method

Abstract The saline aquifer is the most reliable place where anthropogenic carbon dioxide gas storage has shown a promising future. This paper evaluates and predicts the capacities of different carbon dioxide storage trapping mechanisms in storing carbon dioxide gas in low porosity and permeability deep saline aquifers by using commercial reservoir simulator software i.e., Computer modeling group (CMG). Four carbon dioxide storage trapping modeled and simulated were structural or stratigraphic trapping mechanisms, residual trapping mechanisms, solubility trapping mechanisms, and mineral trapping mechanisms. Carbon dioxide gas was injected into a deep saline aquifer for 15 years, followed by 833 years of post-injection. To reflect the real field reality and have a reasonable approximation of the amount of carbon dioxide which can be stored in an aquifer, this paper included water vaporization effects that occur during carbon dioxide injection and water injection operations so as to optimize residual and solubility trapping mechanisms as the most important trapping mechanisms. Furthermore, the effects of different important parameters such as salinity, vertical-to-horizontal permeability ratio, injection rate, bottom hole pressure, and temperature on each carbon dioxide trapping mechanism were analyzed. Results revealed that each carbon dioxide trapping mechanism has a different capacity for storing carbon dioxide and could be either affected linearly or nonlinearly with various parameters. Higher aquifer temperatures are not recommended for carbon dioxide storage because most of the carbon dioxide gas is stored as free gas, which increases the risk of leakage in case of mechanical failure or imbalance. Excess salinity is the only factor that reduces aquifer storage capacity. Furthermore, it was found that an aquifer with a lower vertical-to-horizontal permeability ratio is recommended for carbon dioxide storage because it increases carbon dioxide stored in an immobile phase, which avoids risk leakages. There was an increase of 43.2% and a decrease of 16.84% for minimum and maximum vertical-to-horizontal permeability (kv/kh) ratios, respectively, compared to the base for residual trapping mechanisms. Also, there was a decrease of carbon dioxide dissolved by 19% at maximum kv/kh ratios and an increase of 58% at minimum kv/kh ratios, compared to the base case. Further, there was an increase of carbon dioxide trapped by 96.4% and dissolved by 97% when water was injected at a higher rate compared to the base case (no water injection). Thus, a high injection rate is suggested to enhance residual and solubility trapping mechanisms. It is recommended that the carbon dioxide injection rate and bottom hole pressure be kept at optimal levels to avoid mechanical failure due to aquifer pressures building up, which can increase the risk of leakages and must be monitored and controlled at the surface using pressure gauges or sensor technology.

A study on psychological stress assessment of higher educational institution's students based on computer data mining technology.

Safety begins in the human mind, and the individual's need for psychological safety is the most fundamental need. This fundamental need takes psychological safety as the starting point for the gradual formation of a connection with the outside world. Graduates are the backbone of China's economic development, and their healthy development is of great significance to the sustainable development of China's economy and society. Excessive psychological pressure may bring pain to students in physical and psychological aspects, and even lead to suicide. If students with abnormal psychological pressure can be found in time, the school can provide help and intervention in time to relieve psychological pressure. This paper uses pressure sensor technology for data collection and data mining techniques for data analysis to assess and predict the psychological stress level of Higher Educational Institutions (HEIs) students. The results show that this method can accurately and objectively evaluate the psychological stress of the students, and the evaluation results of students' psychological stress are stable, which can provide students with psychological stress assessment services. It implies that HEI's policymakers should consider these techniques to assess the psychological stress of the students proactively.

Research on vibration compensation technology of pressure sensors in shock wave overpressure measurement

In the dynamic pressure test of explosion shock wave, the interference of seismic wave and mechanical shock makes the interpretation of shock wave pressure measurement more difficult. In this paper, a comparative test is designed to peel off the vibration signal, and the source of vibration in shock wave measurement and the cause of acceleration parasitic effect of pressure sensor are analyzed combined with the data; Then, according to the experimental conclusions and the working principle of the sensor, a new pressure sensor with vibration compensation function is designed; Finally, the feasibility of the new sensor structure for vibration compensation is analyzed by finite element simulation. The results show that the vast majority of vibration interference signals are output by the sensor’s sensitive elements, and the new sensor with double sensitive element compensation can effectively suppress or eliminate the parasitic output caused by vibration interference. The design of the new structure sensor provides ideas for the design of vibration compensation structure of other pressure sensors, and has a certain reference value.

A Zinc-Ion Battery-Type Self-Powered Pressure Sensor with Long Service Life.

Accurate and continuous pressure signal detection without external power supply is a key technology to realize the miniaturization of wearable electronic equipment, the internet of things, and artificial intelligence. However, it is difficult to be achieved by using current sensor technologies. Here, a new one-body strategy, i.e., zinc-ion battery pressure (ZIB-P) sensor technology, which designs the rechargeable solid-state ZIB itself as a flexible pressure sensor is reported. In the device, an isolation layer is introduced into the sandwich configuration solid-state battery to realize the change of device internal resistance by pressure during the transformation of the mechanical signal to the electrical signal. This battery pressure sensor possesses good flexibility, fast response/recovery time (76.0/88.0ms), stable long-term response, excellent cycle stability (100 000 times), and wide pressure detection range (2.0 to 3.68 × 105 Pa). Especially, the excellent charge-discharge performance in the ZIB-P sensor endows it with the real-time detection ability of human vital signs (pulse, limb movement, etc.) and ultrahigh stability without degradation even under 100 000 times pressure stimulation. The ZIB-P sensor strategy provides a new solution for the future development of miniaturized wearable electronic devices.

Functionality of Flexible Pressure Sensors in Cardiovascular Health Monitoring: A Review.

As the highest percentage of global mortality is caused by several cardiovascular diseases (CVD), maintenance and monitoring of a healthy cardiovascular condition have become the primary concern of each and every individual. Simultaneously, recent progress and advances in wearable pressure sensor technology have provided many pathways to monitor and detect underlying cardiovascular illness in terms of irregularities in heart rate, blood pressure, and blood oxygen saturation. These pressure sensors can be comfortably attached onto human skin or can be implanted on the surface of vascular grafts for uninterrupted monitoring of arterial blood pressure. While the traditional monitoring systems are time-consuming, expensive, and not user-friendly, flexible sensor technology has emerged as a promising and dynamic practice to collect important health information at a comparatively low cost in a reliable and user-friendly way. This Review explores the importance and necessity of cardiovascular health monitoring while emphasizing the role of flexible pressure sensors in monitoring patients' health conditions to avoid adverse effects. A comprehensive discussion on the current research progress along with the real-time impact and accessibility of pressure sensors developed for cardiovascular health monitoring applications has been provided.

Pharyngo-Esophageal Modulatory Swallow Responses to Bolus Volume and Viscosity Across Time.

Objectives/HypothesisModulation of the pharyngeal swallow to bolus volume and viscosity is important for safe swallowing and is commonly studied using high‐resolution pharyngeal manometry (HRPM). Use of unidirectional pressure sensor technology may, however, introduce variability in swallow measures and a fixed bolus administration protocol may induce time and order effects. We aimed to overcome these limitations and to investigate the effect of time by repeating randomized measurements using circumferential pressure sensor technology.Study DesignSub‐set analysis of data from the placebo arm of a randomized, repeated measures trial.MethodsHRPM with impedance was recorded using a solid‐state catheter with 36 circumferential pressure sensors and 18 impedance segments straddling from hypopharynx to stomach. Testing included triplicates of 5, 10, and 20 ml thin liquid and 10 ml thick liquid boluses, the order of the thin liquid boluses was randomized. The swallow challenges were repeated approximately 10 minutes after finishing the baseline measurement.ResultsWe included 19 healthy adults (10/9 male/female; age 24.5 ± 4.1 year). Intrabolus pressure, all upper esophageal sphincter (UES) opening and relaxation metrics, and flow timing metrics increased with larger volumes. A thicker viscosity decreased UES relaxation time, UES basal pressure, and flow timing metrics, whereas UES opening extent increased. Pre‐swallow UES basal pressure and post‐swallow UES contractile integral decreased over time.ConclusionUsing circumferential pressure sensor technology, the effects of volume and viscosity were largely consistent with previous reports. UES contractile pressures reduced over time. The growing body of literature offers a benchmark for recognizing aberrant pharyngo‐esophageal motor responses.Level of Evidence3 Laryngoscope, 132:1817–1824, 2022

Virtual Pressure Sensor for Electronic Expansion Valve Control in a Vapor Compression Refrigeration System

Virtual sensor technology, which uses simulation models/algorithms to calculate a value to represent an unmeasured variable or replace a directly measured reading, has attracted many studies in the heating, ventilation, air conditioning and refrigeration (HVAC&amp;R) industry. However, most virtual sensor technologies are developed for fault detection and diagnostics (FDD) purposes, which generally compare the virtual sensor values with actual measured values to detect if any fault occurred and identify the causes that led to the fault. It is rare to see studies focus on control performance of virtual sensors after substituting an actual sensor. This is particularly important for the system with no redundant sensor since a virtual sensor is the most effective way to operate the system in the desirable region when any sensor failure occurs. To address this gap, this paper develops a new virtual pressure sensor technology to substitute the actual pressure measurement for electronic expansion valve (EXV) control in a vapor compression refrigeration system by integrating compressor and valve characteristics. The control performance of this proposed virtual pressure sensor technology under various operating conditions is validated with experimental data. Closed loop EXV control simulations with the proposed virtual pressure sensor are conducted, and the results are analyzed.

Sapphire Fabry–Perot Pressure Sensor at High Temperature

There is a need for pressure sensor technology that can operate for longer times at very high temperatures. We propose a sapphire pressure sensor designed to operate at high temperature. A Fabry-Perot (FP) sensing cavity created by directly bonding two sapphire wafers through reactive-ion etching functions as a single sapphire structure for pressure measurement at high temperatures. Applying white-light interferometry and diaphragm deflection theory, the fabricated device is experimentally tested by measuring the pressure over a range of 0.1 to 2.1 MPa at 25-1000 °C. The FP sensing cavity length depends on the pressure and the temperature simultaneously. The FP sensing cavity length varies linearly with pressure at 25 °C, and the linearity is preserved with different sensitivity at high temperatures. The structure of the sensor body, enveloping the cavity inside, varies via the coefficient of thermal expansion of sapphire like a single sapphire wafer, and the FP sensing cavity is tightly sealed without any air leakage at high temperature.

Ultraminiature and Flexible Sensor Based on Interior Corner Flow for Direct Pressure Sensing in Biofluids.

Conventional pressure sensing devices are well developed for either indirect evaluation or internal measuring of fluid pressure over millimeter scale. Whereas, specialized pressure sensors that can directly work in various liquid environments at micrometer scale remain challenging and rarely explored, but are of great importance in many biomedical applications. Here, pressure sensor technology that utilizes capillary action to self-assemble the pressure-sensitive element is introduced. Sophisticated control of capillary flow, tunable sensitivity to liquid pressure in various mediums, and multiple transduction modes are realized in a polymer device, which is also flexible (thickness of 8 µm), ultraminiature (effective volume of 18 × 100 × 580 µm3 ), and transparent, enabling the sensor to work in some extreme situations, such as in narrow inner spaces (e.g., a microchannel of 220 µm in width and 100 µm in height), or on the surface of small objects (e.g., a 380 µm diameter needle). Potential applications of this sensor include disposables for in vivo and short-term measurements.

A New Blood Pulsation Simulator Platform Incorporating Cardiovascular Physiology for Evaluating Radial Pulse Waveform.

To meet the need for “standard” testing system for wearable blood pressure sensors, this study intends to develop a new radial pulsation simulator that can generate age-dependent reference radial artery pressure waveforms reflecting the physiological characteristics of human cardiovascular system. To closely duplicate a human cardiovascular system, the proposed simulator consists of a left ventricle simulation module, an aorta simulation module, a peripheral resistance simulation module, and a positive/negative pressure control reservoir module. Simulating physiologies of blood pressure, the compliance chamber in the simulator can control arterial stiffness to produce age-dependent pressure waveforms. The augmentation index was used to assess the pressure waveforms generated by the simulator. The test results show that the simulator can generate and control radial pressure waveforms similar to human pulse signals consisting of early systolic pressure, late systolic pressure, and dicrotic notch. Furthermore, the simulator's left ventricular pressure-volume loop results demonstrate that the simulator exhibits mechanical characteristics of the human cardiovascular system. The proposed device can be effectively used as a “standard” radial artery pressure simulator to calibrate the wearable sensor's measurement characteristics and to develop more advanced sensors. The simulator is intended to serve as a platform for the development, performance verification, and calibration of wearable blood pressure sensors. It will contribute to the advancement of the wearable blood pressure sensor technology, which enables real-time monitoring of users' radial artery pressure waveforms and eventually predicting cardiovascular diseases.

LOMOS-mini: A coupled system quantifying transient water and heat exchanges in streambeds

The LOMOS-mini is a new experimental system monitoring transient water and heat fluxes in the hyporheic zone at a sub-daily resolution. Given the coupling of high-frequency hydraulic head gradient and temperature measurements, its innovation when compared to currently available monitoring systems is to operate under transient conditions and to allow the quantification of coupled water and heat exchanges with an unprecented fine temporal resolution, such as the rainfall event time scale. The LOMOS-mini is low-cost, easy to construct from individual microelectronic components and has an autonomy of several months in the field. Its robust implementation protocol makes it suitable for a wide variety of geological environments, from soft loamy, sandy, clayey streambeds to compact colluvial environments. Hydraulic head gradients are measured using the pressure sensor technology presented in Greswell et al. (2009). The sensibility of pressure estimates to ambient temperature is demonstrated; the measurement error is evaluated to decrease by up to one order of magnitude when accounting for temperature in the calibration relationship. Coupled with a physically-based hydrothermal model, the LOMOS-mini provides transient estimates of vertically distributed Darcy fluxes, conductive and advective heat fluxes. The methodology is illustrated on a colluvial streambed case study.

Navvus FFR to reduce CONTRAst, Cost and radiaTion (CONTRACT); insights from a single-centre clinical and economical evaluation with the RXi Rapid-Exchange FFR device

ObjectivesTo assess whether the RXi Navvus system compared to the use of standard Fractional Flow Reserve (FFR) wires reduces total contrast volume, radiation and overall study cost in a real world patient population referred for coronary angiography or percutaneous coronary intervention. BackgroundFFR is the mainstay of functional hemodynamic assessment of coronary artery lesions. The RXi Navvus system (ACIST Medical Systems, Eden Prairie, MN) is a monorail microcatheter with FFR-measurement capability through optical pressure sensor technology. MethodsThis is an investigator-initiated, prospective, single-center, observational cohort study. A total of 238 patients were enrolled, 97 patients with Navvus and 141 with conventional pressure-wire based FFR (PW-FFR). Final analyses were performed on the cohort in which only 1 device was used (82 Navvus procedures vs. 136 PW-FFR procedures). ResultsNo significant differences were found in the total amount of contrast used (150±77 vs 147±79ml; p=0.81), radiation use (6200±4601 vs. 5076±4655 centiG∗cm2; p=0.09) or costs (€1994,- vs. €1930,-; p=0.32) in the Navvus vs. PW-FFR groups respectively. ConclusionsNo significant differences were found in the amount of contrast used, total procedural costs or radiation when the Navvus system was used as compared to conventional FFR wires. Condensed abstractCONTRACT is an investigator-initiated, prospective, single-center, observational cohort study that evaluated whether the RXi Navvus system compared to the use of standard Fractional Flow Reserve (FFR) wires reduces total contrast volume, radiation and overall study cost in a real world patient population referred for coronary angiography or percutaneous coronary intervention. Use of the RXi Navvus system was associated with comparable procedural costs, amount of radiation and contrast used as compared to PW-FFR systems.

Large Area One-Step Facile Processing of Microstructured Elastomeric Dielectric Film for High Sensitivity and Durable Sensing over Wide Pressure Range.

Once the requirement of sensitivity has been met, to enable a flexible pressure sensor technology to be widely adopted as an economic and convenient way for sensing diverse human body motions, critical factors need to be considered including low manufacturing cost, a large pressure detection range, and low power consumption. In this work, a facile approach is developed for one-step processing of a large area microstructured elastomer film with high density microfeatures of air voids, which can be seamlessly integrated into the process flow for fabricating flexible capacitive sensors. The fabricated sensors exhibit fast response and high sensitivity in the low pressure range to be able to detect very weak pressure down to 1 Pa and perform reliable wrist pulse monitoring. Compared to previous work, more advantageous features of this sensor are relatively high sensitivity being maintained in a wide pressure range up to 250 kPa and excellent durability under heavy load larger than 1 MPa, attributed to the formed dense air voids inside the film. A smart insole made with the sensor can accurately monitor the real-time walking or running behaviors and even a small weight change less than 1 kg under a heavy load of a 70 kg adult. For both application examples of wrist pulse monitoring and smart insole, the sensors are operated in a 3.3 V electronic system powered by a Li-ion battery, showing the potential for power-constrained wearable applications.

Sit-To-Stand (STS) timing among older adults in their homes: Two measurement approaches

Sit-to-stand (STS) times required by older adults exiting from their beds at home were compared simultaneously using under mattress pressure sensor technology and video analysis. Six older adults consented to participate in the study and had under mattress pressure technology installed in their homes. Participants were visited monthly over a period of 2-10 months by a researcher who asked them to perform three bed exits which were videotaped. The pressure sensor technology calculated a portion of STS time based on changes in pressure between the end of stable sitting on the edge of the bed and pressure leaving the bed. The video analysis approach calculated this corresponding initial phase of the same STS transfer by determining the difference between the first forward movement from the quiet sitting position and the initiation of vertical rise. The remaining period of vertical rise into a complete standing position was calculated using video analysis but not pressure sensor technology. A Spearman’s rank order correlation analysis revealed that there was a moderate, positive correlation between the video and pressure-sensor measures of the initial phase of STS which was statistically significant (r s =0.50, n=97, p<0.001). Wilcoxon signed-rank tests indicated that pressure sensor times were longer (Z=-7.91, p<0.000) and more variable than video times (Z=-3.14, p=0.002). Analysis of video data revealed that this initial phase of STS represented between 15 to 81% of the total STS time among the 97 sampled STS in this study. Results highlight how the home environment presents a number of conditions affecting differences in STS values obtained by each of these measurement approaches.

Improving Chest Compressions Following Cardiac Arrest: Pushing Ahead

In Canada there are in excess of 40,000 annual cardiac arrests. Unfortunately, survival remains low following both out-of-hospital and in-hospital cardiac arrest, and many premature deaths are believed to be preventable. Studies have shown that high-quality chest compressions are key to survival, and the American Heart Association has summarized the need for: 1) adequate compression depth 2) adequate compression rate 3) avoiding leaning 4) minimizing interruptions 5) and minimizing chest rise. However, both laypersons and professionals are failing to reliably achieve these recommendations. Several devices (which provide real-time visual and audio feedback) have been developed with the goal of improving performance. Voice advisory manikins and motion capture technology utilize accelerometer technology and infrared sensors. Portable devices- including the CPREzyTM, PocketCPRTM, and CPRmeterTM- use accelerometer or pressure sensor technology. A number of defibrillators have been modified to provide real-time feedback. Recently, two applications, iCPR and PocketCPR, have been developed to capitalize on the ubiquity and familiarity of smartphones. These novel devices have shown the potential to improve the quality of chest compressions. What is needed is further research (and development) into how to translate these exciting opportunities into improved survival following cardiac arrest.

A Real Time Vehicle Collision Sensor and Reporting System Using Load Sensor, GSM and GPS Technology

Vehicle collision sensor system and reporting accident to police is an electronic device installed in a vehicle to inform police man in case of accident to track the vehicles location. This system works using pressure sensor, GPS and GSM technology. These technology embedded together to sense the vehicle collision and indicate the position of the vehicle or locate the place of accident in order to solve the problem immediately (as soon as possible).For doing so AT89S52 microcontroller is interfaced serially to a GSM modem, GPS receiver, and pressure sensor. A GSM modem is used to send the position (Latitude and Longitude) of the vehicle, the plate of the vehicle and the SMS text from the accident place. The GPS modem will continuously give the data (longitude and latitude) and Load sensor senses the collision of the vehicle against obstacles and input to microcontroller. As load sensor senses the collision, the GSM start to send the plate of the vehicle, text message and the position of the vehicle in terms of latitude and longitude in real time.