Membrane Surface Research Articles

Efficient separation of HEPES and CO2-derived fructose by nanofiltration: Optimizing pH for improved separation and proposing a potential mechanism

Utilization of an in vitro multi-enzyme catalytic system for the synthesis of fructose from carbon dioxide is a promising approach towards achieving carbon neutrality. However, the lack of effective separation methods for the buffer HEPES (4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid) and the product fructose within the system has hindered the industrialization of in vitro multi-enzyme catalytic synthesis systems. This study aimed to separate and recover HEPES and fructose using nanofiltration technology. We investigated the influence of various parameters, including total solution concentration, solute concentration ratio, pH, and temperature, on the nanofiltration separation performance. Experimental results revealed that increasing the pH to 9.0 significantly decreased the fructose retention rate while maintaining a nearly complete HEPES retention rate. The HEPES-fructose mixed solution was further subjected to diafiltration using a spiral-wound membrane, ultimately yielding fructose and HEPES solutions with purities of 90.22 % and 92.93 %, respectively. Combining separation test results with models such as DSPM-DE, and using characterization methods such as ATR-FTIR and pore size distribution analysis, we observed pore swelling during nanofiltration of the HEPES-fructose solution at pH 9.0. A mechanism for this pore swelling, induced by the dissociation of HEPES under the influence of pH, was proposed: Dissociated HEPES in the solution interacts with the membrane surface at the liquid-membrane interface, causing reversible swelling of the membrane pores at the membrane surface, thereby reducing the retention rate of fructose. The nanofiltration process developed in this study effectively separates HEPES and fructose, enabling resource recycling and cost reduction. Furthermore, this study provides theoretical foundations and practical guidance for the design of nanofiltration separation strategies for similar systems using HEPES as a buffer, holding significant scientific and practical value.

Long-Cycling Cellulose-Based Gel Polymer Electrolyte Utilizing Nanohydrotalcite as a Li+ Transport Redistributor.

The hydroxyl groups on the surface of the cellulose-based gel polymer electrolyte lead to poor interfacial compatibility due to side reactions with lithium sheets. In this paper, a novel cellulose-based gel polymer electrolyte was prepared by uniformly coating the surface of a cellulose membrane with a nanohydrotalcite/PVDF-HFP composite using electrospinning technology. This cellulose-based gel polymer electrolyte exhibits good interfacial compatibility and excellent cycling stability (91.7% specific capacity retention after 500 cycles at 0.5C). Theory and experiments have shown that nanohydrotalcite on the surface of cellulose membrane can effectively prevent the contact of hydroxyl groups with lithium sheets to reduce the side reactions. In addition, nanohydrotalcite can also act as a Li+ transport redistributor to facilitate the uniform deposition of Li+ and reduce the formation of lithium dendrites to extend the cycle life.

Waste heat recovery in carbon capture process using a novel amphipathic inorganic membrane

To reduce the CO2 regeneration heat requirement in the CO2 chemical absorption process, a novel amphipathic ceramic membrane-based transport membrane condenser was developed in this study to act as a heat transfer medium in the rich solvent-split mechanism for enhancing the waste heat recovery performance from the stripped gas (i.e., mainly the gas mixture of CO2 and water vapor). Both hydrophobic and hydrophilic segments coexisted on one membrane surface of amphipathic ceramic membrane, while the other surface was totally hydrophilic. The surface characterization and waste heat recovery performance of the flat sheet amphipathic membrane were investigated, and the original hydrophilic ceramic membrane was adopted as the control. Results showed that the water contact angle with 108.9 ± 4° was screened for the hydrophobic surface of the ceramic membrane to achieve the best waste heat recovery performance. Additionally, the waste heat recovery performance of amphipathic membrane firstly increased and then dropped with an increase in the area ratio of hydrophobic surface to the total membrane surface. The maximum waste heat recovery of 13.39 MJ/(m2·h) was achieved at a hydrophobic area ratio of 37.5 % without segmenting by the hydrophilic surface, which was 5.6 % higher than that of the original hydrophilic ceramic membrane. Furthermore, the maximum water recovery of amphipathic membrane was 8.24 % higher than the original hydrophilic ceramic membrane. When the total area of hydrophobic surface was fixed, dividing the hydrophobic surface into two equally sized hydrophobic segments spaced by the hydrophilic segments could further improve the waste heat recovery performance of amphipathic membrane. This study might provide a new insight on improving the waste heat recovery performance of ceramic membrane.

Mechanisms of electromagnetic field control on mineral scaling in brackish water reverse osmosis: Combined homogenous and heterogeneous nucleation

Electromagnetic field (EMF) treatment has emerged as a promising approach for scaling control due to its cost-effectiveness, simplicity, and low energy consumption. However, there is a limited understanding of the mechanisms by which applied EMF impacts mineral scaling in reverse osmosis (RO) systems. This has led to inconclusive and varied results and uncertainties regarding its effectiveness. This study elucidates the impacts of EMF on homogenous and heterogeneous nucleation and membrane performance during RO desalination of different feedwaters. Our results reveal that EMF exhibits greater efficacy in treating near-saturated water (SI∼0), especially when coupled with extended hydraulic flushing (HF). For saturated brackish water desalination, heterogeneous scaling predominantly occurs on membrane surfaces, with the effectiveness of EMF in inhibiting scaling primarily attributed to the hydration effect. In supersaturated solutions, EMF promotes bulk precipitation due to the magnetohydrodynamic effect, quickly blocking membrane pores. Thus, when the saturation reaches a certain high level during RO desalination, magnetohydrodynamic EMF effects can accelerate flux decline caused by homogeneous scaling. This work provides an efficient method for predicting EMF efficiency, emphasizing the importance of saturation conditions and HF cleaning duration in determining membrane performance, suggesting these show promise for improving undersaturated or near-saturated feedwater desalination via RO.

In-situ confined preparation of COF@GO nanofiltration membranes for high-efficiency dye removal

Graphene oxide membrane (GOM) possesses ultrafast and tunable two-dimensional water transport pathways, making it an ideal candidate for nanofiltration separation of dye wastewater. However, GOM also faces great challenges such as poor aqueous stability, collapse of non-oxygenated regions under high pressure, and limitations imposed by trade-off effects. In this study, covalent organic frameworks (COFs) were in-situ formed within GOM interlayers and on membrane surface to enlarge interlayer spacings and enhance hydrophilicity of GOM simultaneously via a two-step method including monomer retention in GOM and in-situ confined interfacial polymerization of COFs. Fourier transformation infrared spectroscopy (FT-IR) and X-ray photoelectron spectrometry (XPS) results confirmed the successful synthesis of COF on GOM surface, which enhanced membrane surface hydrophilicity and bridged the split defects of GOM. According to X-ray diffraction measurements (XRD) and scanning electron microscope (SEM) results, COF@GO membranes possessed enlarged interlayer spacings and increased thickness of selective layer, which indicated the successful intercalation of COF into GO interlayer. COF@GO-50 membrane exhibited an ultrahigh pure water permeability (PWP) of 148.1 L/(m2·h·bar), with 99.0 % rejection for direct red 80 (DR80) aqueous solution and 9.6 % NaCl rejection. The ultrahigh water permeance might be ascribed to the enlarged interlayer pathways, the shortened vertical pathways provided by in-plane pores of COF nanosheets, and enhanced water adsorption capacity due to enhanced membrane hydrophilicity. Moreover, COF@GO nanofiltration membrane demonstrated excellent anti-fouling properties and long-term stability in 30h continuous operation, maintaining considerable separation efficiency under harsh conditions. This work provides a straightforward and applicable strategy to simultaneously enlarge interlayer spacings and enhance surface hydrophilicity of GOM via in-situ confined preparation of COFs, achieving ultrahigh water permeance and overcoming the trade-off effect between permeability and selectivity of GOM.

Hierarchically structured hollow PVDF nanofibers for flexible piezoelectric sensor

The emergence of flexible sensors addresses the limitations of traditional detection equipment, such as large size, high cost, and inconvenient portability. These sensors have significantly advanced the development of wearable electronic devices for applications in electronic skin, energy harvesting, and energy storage. To enhance the sensitivity of flexible sensors, we developed a hierarchical polyvinylidene fluoride (PVDF) nanofiber-based piezoelectric sensor. By utilizing coaxial electrospinning, we fabricated nanofibers with hollow interiors and porous outer walls. Additionally, microstructures were constructed on the fiber membrane surface by modifying the collector’s shape. The resulting microstructured hollow PVDF nanofiber membrane exhibited high β-phase content (91.31 %), excellent flexibility (maximum strain 56.9 %), and high porosity (88.94 %). The sensor demonstrated a sensitivity of 2.7 V/N (1.08 V/kPa) and a maximum output voltage of 10.1 V, approximately three times higher than that of solid PVDF nanofibers without microstructures. Even after 14,400 cycles of impact, the sensor maintained stable output. The sensor was successfully applied to human activity monitoring and gesture recognition, showcasing its ability to monitor various human activities, respond rapidly (60.4 ms), and synchronously control a mechanical palm to perform different gestures. This work highlights the potential of hierarchically structured hollow PVDF nanofibers in advancing the performance and application scope of flexible piezoelectric sensors.

Engineering mineralized interlayers for enhanced nanofiltration: Synergistic modulation of polyamide layer structure and catalytic self-cleaning performance

High permselectivity and antifouling/self-cleaning nanofiltration (NF) membranes are ideal materials for water treatment, and this vision is expected to be reached through the design of multifunctional self-cleaning interfaces. In this study, we employed metal - polyphenol network (MPN) to mediate in situ mineralization of porous substrates, enabling simultaneous modulation of interfacial polymerization (IP) and catalytic self-cleaning. The findings demonstrate that the mineralized layers employ an interlayer modulation strategy to produce a polyamide (PA) layer that is more hydrophilic, thinner, and structurally denser. As a result, the resulting PA-Fe3O4-PSF membrane exhibited a 2.5-fold increase in permeance (19.2 L m−2 h−1 bar−1) and a 7.3-fold enhancement in Cl−/SO42− selectivity (66.4), compared to the control membrane (PA-PSF). Additionally, its highly polarized membrane surface significantly improved its antifouling performance. Compared to membranes with mineralized layers on the surface (Fe3O4-PA-PSF), PA-Fe3O4-PSF constructs a confined space that facilitates more efficient regeneration through in situ catalytic self-cleaning and ensures greater stability during multiple fouling-regeneration cycle operations. This study paves the way for fabricating multifunctional NF membranes with sustainable applications in material concentration, wastewater treatment, and environmental remediation.

Impact of PCLNPG Nanopolymeric Additive on the Surface and Structural Properties of PPSU Ultrafiltration Membranes for Enhanced Protein Rejection

This research explored the use of a partially cross-linked graft copolymer (PCLNPG) as an innovative nanopolymer pore-forming agent to enhance polyphenylsulfone (PPSU) membranes for protein separation applications. The study systematically examined the impact of incorporating PCLNPG at varying concentrations on the morphological and surface properties of PPSU membranes. A thorough characterization of the resulting PPSU-PCLNPG membranes was performed, focusing on changes in morphology, water affinity, porosity, pore size, and pore size distribution. The experimental findings demonstrated that the use of PCLNPG led to a significantly more porous structure, as confirmed by SEM analysis, with notable increases in porosity and pore size (nearly double). Additionally, the hydrophilicity of the PPSU membrane was remarkably enhanced. Performance evaluations revealed a substantial improvement in pure water flux, with the flux nearly tripling. The BSA retention was directly correlated with the concentration of the PCLNPG pore former for a loading range of 0.25–0.75 wt.%. The incorporation of PCLNPG also reduced the membrane fouling propensity by reducing both cake layer resistance (Rc) and pore plugging resistance (Rp). These results underscore the potential of PCLNPG-PPSU membranes for wastewater reclamation and nutrient recovery applications.

Real-time induced magnetic vibrational based antifouling mechanism for ultrafiltration (UF) membrane

Despite the widespread adoption of membrane technologies for efficient water treatment, membrane fouling remains a significant challenge, reducing separation efficiency, shortening lifespan, and increasing operational costs. Various studies have explored chemical membrane modifications to mitigate fouling, often resulting in adverse effects on flux and selectivity. Based on numerical modeling and experimental investigation, this work introduces real-time induced magnetic vibration as a sustainable approach for membrane antifouling without compromising permeability and selectivity. By preventing or delaying particle deposition on the membrane surface, magnetic vibration reduces fouling intensity. Experimental results demonstrated that different frequencies of magnetic vibration influenced the deposition of foulants (Humic Acid and Sodium Alginate) on the membrane surface. Notably, vibrating the membrane at 10 Hz with centrally attached iron particles led to a 22.4 % reduction in flux when treated with Humic Acid, compared to a 33.9 % reduction without vibration. Exposure to vibrations at the resonance frequency (5 Hz) for 6 h resulted in only a 10 % reduction in flux, effectively preventing the formation of a dense cake layer. Similarly, in the case of Sodium Alginate, a 10 Hz vibration for 2 h decreased the flux reduction from 21.4 % without vibration to 7.3 %, suggesting the preventive effect of vibration on aggregated SA deposition or facilitating continuous displacement for flux retention. Moreover, the study examined the influence of the configuration of iron particles attached to the membranes on the effectiveness of vibration. The study revealed that a striped configuration was more effective than a centralized configuration, owing to the distributed vibration effect across each part of the membrane. Furthermore, the fouling mechanism and rejection percentage were further investigated to enhance understanding of the fouling processes.

Enhancing virus inhibition in track-etched membranes through surface modification with silver nanoparticles and curcumin

The present work reports on the use of silver nanoparticles (AgNPs) and curcumin immobilized on the surface of microfiltration track-etched membranes (mTMs) as antiviral filtration materials. AgNPs were synthesized through the direct reduction of silver nitrate by sodium borohydride in the presence of a stabilizing agent. The synthesized nanoparticles and curcumin were immobilized on polyethyleneimine (PEI)-modified mTMs through a static sorption process. TEM, SEM, UV–vis. spectroscopy and luminescence measurements revealed a uniform distribution of AgNPs and confirmed the presence of curcumin on the membrane surface. The resulting TM-PEI-AgNPs-PVP and TM-PEI-Curcumin hybrid membranes were employed for the filtration of HSV-1, VSV, IAV, and EMCV viruses. While both membrane types exhibited insignificant inhibition for the latter two, they achieved 95 and 99 % inhibition for HSV-1 and VSV, respectively. These findings suggest that hybrid membranes with immobilized AgNPs and curcumin can have potential as antiviral filtration materials.

Oxidative Phosphorylation Does Not Violate the Second Law of Thermodynamics.

In a recent series of papers, James W. Lee reported that mitochondrial oxidative phosphorylation violates the second law of thermodynamics and that it is allowed to do so because it is a "Type-B" process that features lateral and longitudinal membrane asymmetry. We show here that these contentions are based on problematic interpretations of the literature. More reliable values of ΔGredox and ΔGATPsynthesis show that the second law is not violated. More recent reports on the structures of the redox-driven proton pumps (Complexes I, III, and IV) suggest that longitudinal membrane asymmetry does not exist. Finally, Lee's predictions for the concentration of protons localized at the P-side surface of the bioenergetic membrane are likely to be much too high due to several errors; thus, his predicted high values of ΔpHsurface that violate the second law are likely to be wrong. There is currently no strong experimental or theoretical evidence to support the contention that oxidative phosphorylation violates the second law of thermodynamics.

Flexible inner surface of polysulfone membranes prevents platelet adhesive protein adsorption and improves antithrombogenicity in vitro.

We investigated whether the condition of the inner surface of hollow fibers affects the blood compatibility of hemodialyzers. We used scanning probe microscope/atomic force microscopy (SPM/AFM) to investigate the height of the swelling and flexible layers (thickness and softness) on the inner surfaces of the hollow fibers. Next, we tested the blood compatibility between dialyzers comprising a hollow fiber membrane, in which the other dialyzers, except for PVP, were additionally coated using PS membranes coated with other materials. After blood was injected into the dialyzer and plugged, dynamic stimulation was performed by slightly rotating the dialyzer for 4 h, although there was no blood circulation. The vitamin E-coated polysulfone (PS) membrane showed a higher thickness and softness of the flexible layer than the asymmetric cellulose triacetate membrane without polyvinylpyrrolidone (PVP) and the PS membranes with PVP. We found that the dialyzer with vitamin E coating significantly suppressed the decrease in platelets, increase in β-TG, and increase in PF4 compared to those coated with NV polymer. Additionally, as the adsorbed protein on the inner surface, the total protein, fibronectin, and vWF levels were significantly lower in the vitamin E-coated dialyzer. The thickness and softness of the flexible layer of the inner surface of the hollow fiber membrane in vitro affect differences in blood coagulation performance in clinical research. Future clinical trials are required to confirm our results.

Development of a local wall concentration model for the design of single pass tangential flow filtration (SPTFF) systems with viral vector surrogates

Recent advances in the use of viral vectors for gene therapy has created a need for efficient downstream processing of these novel therapeutics. Single-pass tangential flow filtration (SPTFF) can potentially improve final product quality via reductions in shear, and it can increase manufacturing productivity via simple implementation into continuous/intensified processes. This study investigated the impact of variations in pressure and flow rate along the length of the membrane on overall SPTFF performance. Constant-flux filtration experiments at feed fluxes from 14 to 420 L/m2/h (Reynolds numbers <20) were performed using Pellicon® 3 TFF cassettes with fluorescent nanoparticles as model viral vectors. The location of nanoparticle accumulation shifted towards the filter outlet at high conversion and was also a function of the permeate flow configuration. These phenomena were explained using a newly developed concentration polarization model that predicts the distribution in local wall concentration over the length of the membrane. The model accurately captured the observed nanoparticle accumulation trends, including the effects of the permeate flow profile (co-current, divergent, or convergent flow) on nanoparticle accumulation within the SPTFF module. Nanoparticle accumulation at moderate conversion was more uniform using convergent flow, but nanoparticle accumulation at 80 % conversion (5x concentration factor) can be minimized using a divergent flow configuration. The local wall concentration model was also used to evaluate the critical flux by assuming that fouling occurs when the nanoparticle concentration at any point along the membrane surface exceeds 15 % by volume. These results provide important insights for the design and operation of SPTFF technology for inline concentration of viral vectors.

Anti-Toxoplasma gondii effects of XYP1-derived peptides and regulatory mechanisms of XYP1

BackgroundToxoplasmosis, caused by Toxoplasma gondii , poses serious health issues for humans and animals. Individuals with impaired immune systems are more susceptible to severe toxoplasmosis. Pregnant women infected by T. gondii can face the possibility of birth defects and miscarriages. While pyrimethamine and sulfadiazine are commonly used drugs in clinical practice, concerns over their side effects and resistance are on the rise. A spider peptide XYP1 isolated from Lycosa coelestis had potent anti-T. gondii effects, but it had a high synthesis cost and strong cytotoxicity.MethodsThis study intended to modify XYP1 for producing derived peptides via amino acid truncation and substitution. The anti-T. gondii effect was evaluated by trypan blue staining assay and killing experiment of RH strain tachyzoites. The CCK8 and hemolysis assays were used to compare their safeties. The morphological changes of T. gondii were observed by scanning electron microscope and transmission electron microscope. In addition, the mechanism of XYP1 against T. gondii through RNA-sequencing was further explored.ResultsIn vivo and in vitro experiments revealed that XYP1-18 and XYP1-18-1 had excellent anti-T. gondii activity with lower cytotoxicity and hemolysis activity than XYP1. XYP1, XYP1-18, and XYP1-18-1 were able to disrupt the surface membrane integrity of T. gondii tachyzoites, forming pores and causing the disruption of organelles. Furthermore, RNA-sequencing analysis indicated that XYP1 could stimulate the host immune response to effectively eliminate T. gondii and lessen the host’s inflammatory reaction.ConclusionsXYP1-18 had lower cytotoxicity and hemolysis activity than XYP1, as well as significantly extending the survival time of the mice. XYP1 played a role in host inflammation and immune responses, revealing its potential mechanism. Our research provided valuable insights into the development and application of peptide-based drugs, offering novel strategies and directions for treating toxoplasmosis.Graphical

Ultra-hydrophilic MOF-303 on electrospun nanofibers with Burr Puzzles structure for the purification of oily wastewater containing heavy metal ions

The current oil-water separation field is extremely complex and the material system is variable. Therefore, the full process applicability of membrane technology is extremely demanding, both in terms of high oil-water separation efficiency and the treatment of soluble substances in wastewater, such as heavy metal ions. The high demand for membrane performance is accompanied by the complexity of the membrane manufacturing process, resulting in the development of membrane technology being hindered. If we can purify heavy metal ions from wastewater while meeting the conditions of oil-water treatment, and simplify the process flow, it is an innovation that we are happy to see. Herein, the use of a seed pre-embedded growth strategy is taking polyacrylamide (PEI) as a breakthrough point, we take advantage of blending to introduce embedding sites in polyacrylonitrile (PAN) membranes. Uniform growth of MOF-303 with Burr Puzzle structure on membrane surface using in situ hydrothermal growth method. The Burr Puzzles structure on the membrane surface is not only able to effectively deal with nanoscale stabilized oil-water mixture and effectively adsorb heavy metal ions, but also enables the MOF-303 crystals to grow more firmly on the membrane surface, so that the modified membrane still maintains good performance in harsh environments. The separation fluxes of the oil-in-water emulsions were all higher than 6987 L m−2 h−1 for oil-in-water emulsion with a separation efficiency of 98.4 %, and the adsorption efficiency of heavy metal ions was also as high as 98.3 %. After 20 cycles, the membrane maintains its promising performance. Due to its simple preparation process and excellent efficiency of emulsions separation and heavy metal ions separation, simplifies complex membrane processes while meeting the rigors of wastewater treatment. it has great prospects for development in the current complex wastewater treatment process.

Multifunctional membranes with super-wetting interface and in-situ Fenton-like sites for efficient oil-in-water emulsion separation

The surge in oil-in-water (O/W) emulsions poses a threat to the ecological environment. Membrane separation technology can achieve complete O/W emulsion separation through size sieving; however, its efficiency is limited by membrane fouling. In this study, an efficient O/W separation membrane with passive and positive anti-fouling properties was fabricated using Fe3O4 functionalized attapulgite (ATP) nanofibers. The anti-fouling mechanism of the multifunctional membranes for the separation of various O/W emulsions was studied. During separation process, a hydration layer, which mitigates oil adhesion with binding energy as low as −169 kcal·mol−1, forms on the interface of Fe3O4-ATP. When a cationic surfactant is present, positively charged oil droplets are attracted to the membrane surface, where they compress against each other, leading to demulsification and escape. Synergistic effects including electrostatic shielding, interaction energy, and steric hindrance were demonstrated through characterization and simulation. Our findings showed that the membrane exhibited a high filtration efficiency with an oil rejection of over 99 % and a steady flux of over 73 % of its initial value. After filtration, oil fouling degraded into smaller sizes and escaped from the membrane structure through the Fenton-like catalytic function of Fe3O4, resulting in a flux recovery ratio of up to 90 %. This study provides a reference for the construction of multifunctional membranes for efficient separation processes and advancing anti-fouling research on membrane interfaces.

Scaling behavior of cation exchange membrane induced by Ca2+ during the electrodialysis for enriching lithium-containing solutions

Membrane fouling, particularly Ca2+-induced scaling on cation exchange membranes (CEM), hinders the application of electrodialysis in lithium extraction. This study investigated the fouling mechanisms of Ca2+ coexisting with Cl− and SO42− on sulfonated CEM, using CaCl2 and CaSO4 solution as the targeted foulants. The conductivity, pH, turbidity, particle size distribution, chemical composition and morphology of the membrane surface were monitored to verify the evolution of the bulk solution and the membrane during the Ca2+-induced fouling. Online detection of conductivity and pH revealed distinct trends in fouling solutions containing Ca2+-Cl- and Ca2+-SO42-. Noticeable changes in turbidity and particle distribution were observed in the concentrated chamber of the highly saturated Ca2+-SO42- solution, whereas the concentrated chamber of the Ca2+-Cl- solution showed turbidity and particle size distribution similar to the initial values. SEM showed that there are different morphologies of scaling crystals in the two types of solution. These fundamental differences are the root cause of the distinct fouling mechanisms between the Ca2+-Cl- solution and Ca2+-SO42- solution. To further investigate the fouling mechanisms, the electrochemical impedance spectroscopy (EIS) was employed to differentiate the impedance of the electric double layer and diffusion layer, providing insights into the characteristics of the CEM-solution interfaces fouled by different lithium-containing solutions. Additionally, adsorption experiments, quartz crystal microbalance with dissipation (QCM-D) and computational simulations (COMSOL, DFT) were conducted to provide detailed insights into the effects of fouling solutions on the properties of the desalted solution, the probability of crystal precipitation, and particularly the interaction between Ca2+ and the functional sites on the CEM. Finally, the Ca2+-induced scaling mechanism of CEM for enriching the lithium-containing solutions with and without SO42− was proposed, elucidating the synergistic effects of Ca2+-induced crystallization in the bulk solution and Ca2+ adsorption on the CEM surface. The research results could offer theoretical guidance for developing pollution control strategies.

Barrier Membrane with Janus Function and Structure for Guided Bone Regeneration.

Guided bone regeneration (GBR) technology has been demonstrated to be an effective method for reconstructing bone defects. A membrane is used to cover the bone defect to stop soft tissue from growing into it. The biosurface design of the barrier membrane is key to the technology. In this work, an asymmetric functional gradient Janus membrane was designed to address the bidirectional environment of the bone and soft tissue during bone reconstruction. The Janus membrane was simply and efficiently prepared by the multilayer self-assembly technique, and it was divided into the polycaprolactone isolation layer (PCL layer, GBR-A) and the nanohydroxyapatite/polycaprolactone/polyethylene glycol osteogenic layer (HAn/PCL/PEG layer, GBR-B). The morphology, composition, roughness, hydrophilicity, biocompatibility, cell attachment, and osteogenic mineralization ability of the double surfaces of the Janus membrane were systematically evaluated. The GBR-A layer was smooth, dense, and hydrophobic, which could inhibit cell adhesion and resist soft tissue invasion. The GBR-B layer was rough, porous, hydrophilic, and bioactive, promoting cell adhesion, proliferation, matrix mineralization, and expression of alkaline phosphatase and RUNX2. In vitro and in vivo results showed that the membrane could bind tightly to bone, maintain long-term space stability, and significantly promote new bone formation. Moreover, the membrane could fix the bone filling material in the defect for a better healing effect. This work presents a straightforward and viable methodology for the fabrication of GBR membranes with Janus-based bioactive surfaces. This work may provide insights for the design of biomaterial surfaces and treatment of bone defects.

Ginsenoside Rh2 Alleviates LPS-Induced Inflammatory Responses by Binding to TLR4/MD-2 and Blocking TLR4 Dimerization.

Lipopolysaccharide (LPS) triggers a severe systemic inflammatory reaction in mammals, with the dimerization of TLR4/MD-2 upon LPS stimulation serving as the pivotal mechanism in the transmission of inflammatory signals. Ginsenoside Rh2 (G-Rh2), one of the active constituents of red ginseng, exerts potent anti-inflammatory activity. However, whether G-Rh2 can block the TLR4 dimerization to exert anti-inflammatory effects remains unclear. Here, we first investigated the non-cytotoxic concentration of G-Rh2 on RAW 264.7 cells, and detected the releases of pro-inflammatory cytokines in LPS-treated RAW 264.7 cells, and then uncovered the mechanisms involved in the anti-inflammatory activity of G-Rh2 through flow cytometry, fluorescent membrane localization, Western blotting, co-immunoprecipitation (Co-IP), molecular docking and surface plasmon resonance (SPR) analysis in LPS-stimulated macrophages. Our results show that G-Rh2 stimulation markedly inhibited the secretion of LPS-induced interleukin-6 (IL-6), tumor necrosis factor-α (TNF-α) and nitric oxide (NO). Additionally, G-Rh2 blocked the binding of LPS with the membrane of RAW 264.7 cells through direct interaction with TLR4 and MD-2 proteins, leading to the disruption of the dimerization of TLR4 and MD-2, followed by suppression of the TLR4/NF-κB signaling pathway. Our results suggest that G-Rh2 acts as a new inhibitor of TLR4 dimerization and may serve as a promising therapeutic agent against inflammation.

Investigating the In Vivo Biodistribution of Extracellular Vesicles Isolated from Various Human Cell Sources Using Positron Emission Tomography.

Positron emission tomography (PET) is a powerful tool for investigating the in vivo behavior of drug delivery systems. We aimed to assess the biodistribution of extracellular vesicles (EVs), nanosized vesicles secreted by cells isolated from various human cell sources using PET. EVs were isolated from mesenchymal stromal cells (MSCs) (MSC EVs), human macrophages (Mϕ EVs), and a melanoma cell line (A375 EVs) by centrifugation and were conjugated with deferoxamine for radiolabeling with Zr-89. PET using conjugated and radiolabeled EVs evaluated their in vivo biodistribution and tissue tropisms. Our study also investigated differences in mouse models, utilizing immunocompetent and immunocompromised mice and an A375 xenograft tumor model. Lastly, we investigated the impact of different labeling techniques on the observed EV biodistribution, including covalent surface modification and membrane incorporation. PET showed that all tested EVs exhibited extended in vivo circulation and generally low uptake in the liver, spleen, and lungs. However, Mϕ EVs showed high liver uptake, potentially attributable to the intrinsic tissue tropism of these EVs from the surface protein composition. MSC EV biodistribution differed between immunocompetent and immunodeficient mice, with increased spleen uptake observed in the latter. PET using A375 xenografts demonstrated efficient tumor uptake of EVs, but no preferential tissue-specific tropism of A375 EVs was found. Biodistribution differences between labeling techniques showed that surface-conjugated EVs had preferential blood circulation and low liver, spleen, and lung uptake compared to membrane integration. This study demonstrates the potential of EVs as effective drug carriers for various diseases, highlights the importance of selecting appropriate cell sources for EV-based drug delivery, and suggests that EV tropism can be harnessed to optimize therapeutic efficacy. Our findings indicate that the cellular source of EVs, labeling technique, and animal model can influence the observed biodistribution.