Superluminescent Diode Research Articles

Short-wavelength InAlGaAs/AlGaAs quantum dot superluminescent diodes

This paper reports the fabrication of J-shaped bent-waveguide superluminescent diodes utilizing an InAlGaAs/AlGaAs quantum dot active region. The emission spectrum of the device is centred at 884 nm with a full width at half maximum of 37 nm and an output power of 18 mW. By incorporating an Al composition into the quantum dot active region, short-wavelength superluminescent diode devices can be obtained. An intersection was found for the light power-injection current curves measured from the straight-waveguide facet and the bent-waveguide facet, respectively. The result is attributed to the conjunct effects of the gain and the additional loss of the bent waveguide. A numerical simulation is performed to verify the qualitative explanation. It is shown that bent waveguide loss is an important factor that affects the output power of J-shaped superluminescent diode devices.

Evaluation of caries-affected dentin with optical coherence tomography

The purpose of this study was to evaluate the degree of demineralization of artificially induced caries-affected human dentin by an in vitro microbiological method. The occlusal surfaces of 6 human molar teeth were abraded until a flat surface was obtained, and the enamel was removed to expose the occlusal dentin surface. These teeth were sectioned in 12 halves in the vestibular-lingual direction and divided into 3 groups according to the period length of the microbiological essay (n = 4): G1, 7 days; G2, 14 days; and G3, 21 days. The surfaces of all specimens were protected by an acid-resistant nail varnish, except for a window where the caries lesion was induced by a Streptoccocus mutans biofilm in a batch-culture model supplemented with 5% sucrose. The specimens were then analyzed by optical coherence tomography (OCT) with a super-luminescent light diode (Λ = 930 nm) with 6.0-µm lateral and longitudinal resolution (in the air). Qualitative and quantitative results (images and average dentin demineralization, respectively) were obtained. The mean demineralization depths were (µm) 235 ± 31.4, 279 ± 14, and 271 ± 8.3 in groups 1, 2, and 3, respectively. In addition, no significant change was observed in the lesion mean depth from 7 days of cariogenic challenge on. In conclusion, OCT was shown to be an efficient and non-invasive method to detect the depths of lesions caused by demineralization. Further, a seven-day demineralization time was considered sufficient for caries-affected dentin to be obtained.

A battery-operated, stabilized, high-energy pulsed electron gun for the production of rare gas excimers

We report on the design of a new type of hot-filament electron gun delivering fairly high current (a few hundreds of μ A) at high voltage (up to 100 kV) in continuous or pulsed mode. Its novel features are that the filament is heated by means of a pack of rechargeable batteries floated atop the high-voltage power supply in order to get rid of bulky isolation transformers, and that the filament current and, hence, the electron gun current, is controlled by a feedback circuit including a superluminescent diode decoupled from the high voltage by means of an optical fiber. This electron gun is intended for general purposes, although we have especially developed it to meet the needs of our experiment on the infrared emission spectroscopy of rare gas excimers. Our experiment requires that the charge injection into the sample is pulsed and constant and stable in time. The new electron gun can deliver several tens of nC per pulse of electrons of energy up to 100 keV into the sample cell. The new design also eliminates ripples in the emission current and ensures up to 12 h of stable performance.

Broadband superluminescent diodes and semiconductor optical amplifiers for the spectral range 750 — 800 nm

We have studied superluminescent diodes (SLDs) and semiconductor optical amplifiers (SOAs) based on an (AlxGa1-x)As/GaAs single quantum well structure with an Al content x ∼ 0.1 in a 10-nm-thick active layer. Depending on the length of the active channel, the single-mode fibre coupled cw output power of the SLDs is 1 to 30 mW at a spectral width of about 50 nm. The width of the optical gain band in the active channel exceeds 40 nm. Preliminary operating life tests have demonstrated that the devices are sufficiently reliable.

Unifying intensity noise and second-order coherence properties of amplified spontaneous emission sources

We present joint investigations of relative intensity noise (RIN) and second-order coherence properties of amplified spontaneous emission (ASE) generated by a superluminescent diode. We introduce a generalized intensity noise description for ASE sources that contains the shot noise contribution but also accounts for first- and second-order coherence properties reflecting the process of light generation. We find excellent agreement between pump-current-dependent RIN values and this new description, with the perspective of particular interesting consequences for the realization of low-noise broadband emitters.

Compound prism design principles, III: linear-in-wavenumber and optical coherence tomography prisms

We extend the work of the first two papers in this series [Appl. Opt. 50, 4998-5011 (2011), Appl. Opt. 50, 5012-5022 (2011)] to design compound prisms for linear-in-wavenumber dispersion, especially for application in spectral domain optical coherence tomography (OCT). These dispersive prism designs are believed to be the first to meet the requirements of high resolution OCT systems in direct-view geometry, where they can be used to shrink system size, to improve light throughput, to reduce stray light, and to reduce errors resulting from interpolating between wavelength- and wavenumber-sampled domains. We show prism designs that can be used for thermal sources or for wideband superluminescent diodes centered around wavelengths 850, 900, 1300, and 1375 nm.

Research of Angled 8° Integrated 808 nm Wavelength SLDs

Integrated 808 nm wavelength super-luminescent diodes (SLDs) with a ring seed source and a tapered amplifier were fabricated tilted at 8° from the facet normal. Max-output power of 700 mW was obtained in continuous wave (CW) mode under room temperature, and the full width at half maximum (FWHM) of the emission spectrum is 36 nm.

High Performance 785 nm Wavelength Super-Luminescent Diodes

High-performance 785 nm wavelength super-luminescent diodes (SLDs) with ring cavity were fabricated. The maximum output power of 100 mW was obtained in continuous wave (CW) mode under room temperature. The full width at half maximum (FWHM) of the emission spectrum was 24 nm.

Variations in the output characteristics of broadband superluminescent diodes during long-term operation

A method of service life tests of SLD-37 quantum-well superluminescent diodes (SLDs), which are widely used in optical coherence tomography, is described and the results of tests are presented. Special attention is given to variations in the emission spectra of SLDs during their aging. It is shown that this method can be used as an incoming test to select processed semiconductor heterostructures with the longest expected lifetime for fabrication of active elements of SLD modules.

Reduction of parasitic interferences in digital holographic microscopy by numerically decreased coherence length

Due to the large coherence length of laser light, optical path length (OPL) resolution in laser based digital holographic microscopy suffers from parasitic interferences caused by multiple reflections within the experimental setup. Use of partially coherent light reduces this drawback but requires precise and stable matching of object and reference arm’s OPLs and limits the spatial frequency of the interference pattern in off-axis holography. Here, we investigate if the noise properties of spectrally broadened light sources can be generated numerically. Therefore, holograms are coherently captured at different laser wavelengths and the corresponding reconstructed wave fields are numerically superimposed utilizing variable weightings. Gaussian and rectangular spectral shapes of the so synthesized field are analyzed with respect to the resulting noise level, which is quantified in OPL distributions of a reflective test target. Utilizing a Gaussian weighting, the noise level is found to be similar to the one obtained with the partially coherent light of a superluminescent diode. With a rectangular shaped synthesized spectrum, noise is reduced more efficient than with a Gaussian one. The applicability of the method in label-free cell analysis is demonstrated by quantitative phase contrast images obtained from living cancer cells.

Novel Optical Fiber Gas Sensing System Based on FBG Filtering

Based on law of Beer-Lambert, a novel optical fiber gas sensing system is designed to determine the concentration of gas. The narrow-band filtering characteristic of optical fiber Bragg grating is used by this system to produce the narrow spectrum light signal which is wanted in difference absorption measuring. The system has full optical fiber structure, which is mainly composed by super luminescent emitting diode (SLED), optical fiber of 10km, optical fiber gas detector, optical fiber isolator, optical fiber coupler network, optical fiber detecting grating, photoelectric detector and data processing unit. The aspheric objective optical fiber collimator is adopted by this system to compose optical fiber gas sensing detector, which enhances the optic stability of the detector, diminishes the injection loss and makes the echo signal of the optical fiber detector greatly diminished. Experimental data and results show that this system has its feasibility and it can be used for real time monitoring of gas concentration in the domains of colliery and natural gas station, etc.

Theoretical investigation of a surface-emitting superluminescent diode with a circular grating

A novel surface-emitting superluminescent diode (SLD) having a round active region surrounded by a circular grating is theoretically investigated. When the superluminescent light produced in the active region transmits to the passive region, it is coupled out of the device by the detuned circular grating, forming a symmetric surface-emitting beam that could not be obtained from previous devices. The calculation of the grating shows that a reflectivity below 10−3 can be achieved and is low enough to avoid lasing. Performances of devices using single and double quantum wells in the active regions have been simulated, which confirms feasibility of the new design, but also shows that the proposed SLD is unsuitable for high-power applications because of its relatively short length of gain compared to common stripe devices.

Noninvasive imaging of the human rod photoreceptor mosaic using a confocal adaptive optics scanning ophthalmoscope

The rod photoreceptors are implicated in a number of devastating retinal diseases. However, routine imaging of these cells has remained elusive, even with the advent of adaptive optics imaging. Here, we present the first in vivo images of the contiguous rod photoreceptor mosaic in nine healthy human subjects. The images were collected with three different confocal adaptive optics scanning ophthalmoscopes at two different institutions, using 680 and 775 nm superluminescent diodes for illumination. Estimates of photoreceptor density and rod:cone ratios in the 5°–15° retinal eccentricity range are consistent with histological findings, confirming our ability to resolve the rod mosaic by averaging multiple registered images, without the need for additional image processing. In one subject, we were able to identify the emergence of the first rods at approximately 190 μm from the foveal center, in agreement with previous histological studies. The rod and cone photoreceptor mosaics appear in focus at different retinal depths, with the rod mosaic best focus (i.e., brightest and sharpest) being at least 10 μm shallower than the cones at retinal eccentricities larger than 8°. This study represents an important step in bringing high-resolution imaging to bear on the study of rod disorders.

Broadband tunable external cavity laser using a bent-waveguide quantum-dot superluminescent diode as gain device

A broadband tunable grating-coupled external cavity laser is realized by employing a self-assembled InAs/GaAs quantum-dot (QD) superluminescent diode (SLD) as the gain device. The SLD device is processed with a bent-waveguide structure and facet antireflection (AR) coating. Tuning bandwidths of 106 nm and 117 nm are achieved under 3-A and 3.5-A injection currents, respectively. The large tuning range originates essentially from the broad gain spectrum of self-assembled QDs. The bent waveguide structure combined with the facet AR coating plays a role in suppressing the inner-cavity lasing under a large injection current.

Reflective afocal broadband adaptive optics scanning ophthalmoscope

A broadband adaptive optics scanning ophthalmoscope (BAOSO) consisting of four afocal telescopes, formed by pairs of off-axis spherical mirrors in a non-planar arrangement, is presented. The non-planar folding of the telescopes is used to simultaneously reduce pupil and image plane astigmatism. The former improves the adaptive optics performance by reducing the root-mean-square (RMS) of the wavefront and the beam wandering due to optical scanning. The latter provides diffraction limited performance over a 3 diopter (D) vergence range. This vergence range allows for the use of any broadband light source(s) in the 450-850 nm wavelength range to simultaneously image any combination of retinal layers. Imaging modalities that could benefit from such a large vergence range are optical coherence tomography (OCT), multi- and hyper-spectral imaging, single- and multi-photon fluorescence. The benefits of the non-planar telescopes in the BAOSO are illustrated by resolving the human foveal photoreceptor mosaic in reflectance using two different superluminescent diodes with 680 and 796 nm peak wavelengths, reaching the eye with a vergence of 0.76 D relative to each other.

In situ control and monitoring of photonic device intermixing during laser irradiation

Apparatus and method for the in situ control of photonic device intermixing processes are described. The setup utilises an optical fiber splitter which delivers photons to selectively anneal the photonic device and simultaneously measures the emission spectra from the device to monitor the intermixing process in real time. The in situ monitoring of a laser annealing process for the modification of a semiconductor laser diode facet is demonstrated using the instrumentation. A progressive blueshift in the emission wavelength of the device can clearly be observed in real time while high energy photons are delivered to anneal the device facet, hence enabling the control on the degree of intermixing required. This instrumentation is also ideal for broadening of emission spectra in quantum dot and quantum well based light emitting devices such as superluminescent diodes and broadband laser.

Basic characteristics of interference image obtained using spatially phase-modulated mirror array

Single-shot full-field optical coherence tomography (OCT) using spatially phase-modulated reference light has been proposed to achieve a higher sensitivity.16) The reference light can be generated by a spatially phase-modulated mirror array (SPMA). The basic characteristics of an interference image using SPMA have been demonstrated using a superluminescent diode (SLD) with a center wavelength of 840 nm as a popular low-coherence light source. SPMA consisted of a small mirror of 10 × 10 mm2 and had a full area of 5 × 5mm2. The magnifications in the reference arm were 3, 2, and 1. The corresponding magnifications in the signal arm were 18.1, 12.2, and 5.2. The ratios of the interference area to the full CCD area were 0.68, 0.32, and 0.13. Visibilities and ratios for calculations were measured at 0.38 (54%), 0.19 (28%), and 0.062 (8.2%). The periodical background noise was high owing to interferences with scattered lights from SPMA. From the spectra of signal intensity profiles in the subtracted image between two interference images, it was confirmed that the optical phase in the reference light was spatially and periodically modulated by SPMA.

Axial-scanning low-coherence interferometer method for noncontact thickness measurement of biological samples

We investigated a high-precision optical method for measuring the thickness of biological samples regardless of their transparency. The method is based on the precise measurement of optical path length difference of the end surfaces of objects, using a dual-arm axial-scanning low-coherence interferometer. This removes any consideration of the shape, thickness, or transparency of testing objects when performing the measurement. Scanning the reference simplifies the measurement setup, resulting in unambiguous measurement. Using a 1310 nm wavelength superluminescent diode, with a 65 nm bandwidth, the measurement accuracy was as high as 11.6 μm. We tested the method by measuring the thickness of both transparent samples and nontransparent soft biological tissues.

Highly dynamic and versatile pulsed fiber amplifier seeded by a superluminescence diode

We propose and investigate a high power superluminescence diode (SLD) as a pulsed seed source for a highly dynamic and versatile pulse fiber amplifier system. The SLD provides, contrary to conventional Fabry–Perot laser diodes, a smooth and broad output spectrum which is independent of the input pulse parameters. The output pulses from the SLD are as short as 10 ns with up to 150 mW peak power. Moreover, the pulses can be directly shaped by modulating the injection current of the SLD. Pulse shaping in an amplifier configuration is demonstrated without the observation of stimulated Brillouin scattering (SBS) due to the provided spectral bandwidth of 10 nm FWHM. Further spectral shaping was realized with a band pass filter in the amplifier chain.

Measurement of the fluid-velocity profile using a self-mixing superluminescent diode

A novel optical Doppler velocimeter using a self-mixing superluminescent diode is proposed and demonstrated. The operation mechanism uses the photodiode on the back-face of a commercial superluminescent diode to detect the Doppler signal from an interferometer. Thanks to the low coherence length of the optical source, the position of the measuring volume can be easily moved into the sample under test by adjusting the reference arm length, thus allowing us to measure the velocity profile of the flowing scatterers even in turbid media. The proposed velocimeter is expected to have several industrial as well as medical applications.