Structural Materials Research Articles

Design of a first-of-A-kind instrumented advanced test reactor irradiation Capsule experiment for In situ thermal conductivity measurements of metallic fuel

Metallic fuel undergoes dramatic microstructural changes early in life due to fission gas swelling until ∼2–3 at% burnup which affects the conductivity of the material, however the evolution of metallic fuel thermal conductivity during this early phase burnup has never been successfully measured in situ. The Irradiated Material Properties Accelerated Characterization Test (IMPACT) experiment will be the first in a series of experiments to irradiate advanced nuclear metallic fuel specimens with novel embedded thermal conductivity probes in ATR. In the current work the IMPACT experiment final design and supporting analysis is reported in detail. Results are evaluated for various reactor operational conditions to meet the functional requirements of the experiment. The first iteration of this IMPACT experiment will provide data regarding thermal properties evolution in uranium-zirconium (U10Zr) fuel, but this experiment vehicle is envisioned for future advanced fuels and structural materials irradiations in ATR.

A novel high-entropy alloy with excellent mechanical properties, corrosion resistance, and antibacterial properties

Microbiologically influenced corrosion is a challenge problem involving many fields and causes great corrosion losses. Developing antibacterial structural materials is one of the effective strategies to solve above issues. The current study reports a novel Al0.2CoCrFeNiCu0.3Ta0.1 HEA with outstanding mechanical properties, corrosion resistance, and antibacterial properties. The HEA exhibited a face-centered cubic (FCC) structure with L12 nanoprecipitates enriched in Al–Ni–Ta–Cu that are dispersed in the FCC matrix. Antibacterial rate of the HEA against Bacillus subtilis was more than 99.99 %, which was far superior to that of the traditional antibacterial Cu-bearing 304 stainless steel (72.84 %). The ultimate tensile strength and yield strength of the HEA were 1053.5 MPa and 602.5 MPa, respectively, which were much higher than those of traditional antibacterial Cu-bearing 304 stainless steel (530.5 MPa and 242.8 MPa, respectively) without apparent loss of ductility. In addition, this HEA displayed an excellent corrosion resistance that was superior to that of 304 stainless steel and antibacterial Cu-bearing 304 stainless steel.

Design and preparation of low-temperature curable, tough, repairable epoxy containing hindered urea-based dynamic reversible bonds

ABSTRACT Traditional epoxy resins are of technological significance for structural adhesives and composite materials, as well as many others. However, brittleness limits its further development, and achieving a combination of toughness and rigidity in epoxy networks remains a great challenge. In this work, we designed and synthesized low-temperature curable, tough and repairable epoxy networks via hindered urea bond (HUB) crosslinking strategies. Mechanical testing revealed that the material exhibited simultaneously improved toughness and stiffness, and specifically, tensile strength, elongation at break, and toughness were able to reach 78.2 MPa, 8.61%, and 4.63 MJ · m−3, respectively. More importantly, the dynamic exchange of HUB dispersed between polymer chains enables HUB crosslinked epoxy with thermal-triggered reparability and recyclability. In addition, thermal properties, chemical stability and water resistance of toughened epoxy samples were also characterized. This work provides a practical guidance for the exploration of high-performance epoxy with the potential to be extended to other polymers.

B-MAR: bidirectional artifact representations learning framework for metal artifact reduction in dental CBCT

Objective. Metal artifacts in computed tomography (CT) images hinder diagnosis and treatment significantly. Specifically, dental cone-beam computed tomography (Dental CBCT) images are seriously contaminated by metal artifacts due to the widespread use of low tube voltages and the presence of various high-attenuation materials in dental structures. Existing supervised metal artifact reduction (MAR) methods mainly learn the mapping of artifact-affected images to clean images, while ignoring the modeling of the metal artifact generation process. Therefore, we propose the bidirectional artifact representations learning framework to adaptively encode metal artifacts caused by various dental implants and model the generation and elimination of metal artifacts, thereby improving MAR performance. Approach. Specifically, we introduce an efficient artifact encoder to extract multi-scale representations of metal artifacts from artifact-affected images. These extracted metal artifact representations are then bidirectionally embedded into both the metal artifact generator and the metal artifact eliminator, which can simultaneously improve the performance of artifact removal and artifact generation. The artifact eliminator learns artifact removal in a supervised manner, while the artifact generator learns artifact generation in an adversarial manner. To further improve the performance of the bidirectional task networks, we propose artifact consistency loss to align the consistency of images generated by the eliminator and the generator with or without embedding artifact representations. Main results. To validate the effectiveness of our algorithm, experiments are conducted on simulated and clinical datasets containing various dental metal morphologies. Quantitative metrics are calculated to evaluate the results of the simulation tests, which demonstrate b-MAR improvements of >1.4131 dB in PSNR, >0.3473 HU decrements in RMSE, and >0.0025 promotion in structural similarity index measurement over the current state-of-the-art MAR methods. All results indicate that the proposed b-MAR method can remove artifacts caused by various metal morphologies and restore the structural integrity of dental tissues effectively. Significance. The proposed b-MAR method strengthens the joint learning of the artifact removal process and the artifact generation process by bidirectionally embedding artifact representations, thereby improving the model’s artifact removal performance. Compared with other comparison methods, b-MAR can robustly and effectively correct metal artifacts in dental CBCT images caused by different dental metals.

Efficient Transformation of Water Vapor into Hydrogen by Dielectric Barrier Discharge Loaded with Bamboo Carbon Bed Structured by Fibrous Material.

A new method of efficiently transforming water vapor into hydrogen was investigated by dielectric barrier discharge (DBD) loaded with bamboo carbon bed structured by fibrous material in an argon medium. Hydrogen productivity was measured in three different reactors: a non-loaded DBD (N-DBD), a bamboo carbon (BC) bed DBD (BC-DBD), and a quartz wool (QW)-loaded BC DBD (QC-DBD). The effects of the quality ratio of BC to QW and relative humidity on hydrogen productivity were also investigated in QC-DBD at various flow rates. The reaction process and mechanism were analyzed by scanning electron microscopy, X-ray photoelectron spectroscopy, N2 physisorption experiments, infrared spectroscopy, and optical emission spectroscopy. A new reaction pathway was developed by loading BC into the fibrous structured material to activate the reaction molecules and capture the O-containing groups in the DBD reactor. A hydrogen productivity of 17.3 g/kWh was achieved at an applied voltage of 5 kV, flow rate of 4 L/min, and 100% relative humidity (RH) in the QC-DBD with a quality ratio of BC to QW of 3.0.

The Irradiation Effects in Ferritic, Ferritic-Martensitic and Austenitic Oxide Dispersion Strengthened Alloys: A Review.

High-performance structural materials (HPSMs) are needed for the successful and safe design of fission and fusion reactors. Their operation is associated with unprecedented fluxes of high-energy neutrons and thermomechanical loadings. In fission reactors, HPSMs are used, e.g., for fuel claddings, core internal structural components and reactor pressure vessels. Even stronger requirements are expected for fourth-generation supercritical water fission reactors, with a particular focus on the HPSM's corrosion resistance. The first wall and blanket structural materials in fusion reactors are subjected not only to high energy neutron irradiation, but also to strong mechanical, heat and electromagnetic loadings. This paper presents a historical and state-of-the-art summary focused on the properties and application potential of irradiation-resistant alloys predominantly strengthened by an oxide dispersion. These alloys are categorized according to their matrix as ferritic, ferritic-martensitic and austenitic. Low void swelling, high-temperature He embrittlement, thermal and irradiation hardening and creep are typical phenomena most usually studied in ferritic and ferritic martensitic oxide dispersion strengthened (ODS) alloys. In contrast, austenitic ODS alloys exhibit an increased corrosion and oxidation resistance and a higher creep resistance at elevated temperatures. This is why the advantages and drawbacks of each matrix-type ODS are discussed in this paper.

Dynamics of resonant magnetoelectric effect in a magnetoactive elastomer based cantilever: Magnetic field induced orientation transition and giant frequency tuning

Magnetoelectric (ME) effects in composite heterostructures containing mechanically coupled ferromagnetic and piezoelectric layers enable the mutual transformation of magnetic and electric fields and form the basis for the development of magnetic field sensors, actuators and energy harvesters. Promising materials for such composite structures are magnetoactive elastomers (MAE), which are silicone matrices with ferromagnetic particles uniformly distributed within them. The strong dependence of MAE properties on magnetic fields and their low rigidity enable contactless control of ME effects characteristics within such structures. In this work we have experimentally investigated the dynamics of resonant ME effects in a structure consisting of a MAE layer with carbonyl iron particles and a layer of polyvinylidene fluoride piezopolymer in a cantilever geometry. For the structure magnetized in a plane along the axis, the frequency tuning of the bending oscillations reached 360 % at the fields up to 2 kOe, and the maximum ME conversion coefficient was 1.74 V/(Oe·cm). For the structure magnetized perpendicular to the plane, an orientation transition was observed, which manifested itself as a jump-like bending of the structure to the angle up to ∼850 at magnetic field above the critical value. The frequency tuning by the magnetic field reached 185 %, and the maximum ME conversion coefficient was 135 V/(Oe·cm). A model has been developed that qualitatively describes the dynamics of ME effect in composite cantilever structures with a MAE layer for different orientations of the applied magnetic field.

Visualizing the Heterogeneity in Homogeneous Supramolecular Polymers.

The dynamic properties of supramolecular polymers enable new functionality beyond the limitations of conventional polymers. The mechanism of the monomer exchange between different supramolecular polymers is proposed to be closely associated with local disordered domains within the supramolecular polymers. However, a direct detection of such heterogeneity has never been experimentally probed. Here, we present the direct visualization of the local disordered domains in the backbone of supramolecular polymers by a super-resolution microscopy technique: Nile Red-based spectrally resolved point accumulation for imaging in nanoscale topography (NR-sPAINT). We investigate the local disordered domains in trisamide-based supramolecular polymers comprising a (co)assembly of benzene-1,3,5-tricarboxamide (BTA) and a variant with one of the amide bonds inverted (iBTA). The NR-sPAINT allows us to simultaneously map the spatial distribution and polarity of the local disordered domains along the polymers with a spatial precision down to ∼20 nm. Quantitative autocorrelation and cross-correlation analysis show subtle differences in the spatial distribution of the disordered domains between polymers composed of different variants of BTA monomers. Further, statistical analysis unraveled high heterogeneity in monomer packing at both intra- and interpolymer levels. The results reported here demonstrate the necessity of investigating the structures in soft materials at nanoscale to fully understand their intricacy.

Effect of external magnetic field on microstructures and mechanical properties of Ti-2Al-1.5Mn titanium alloy resistance spot welds

The excellent specific strength and elevated-temperature mechanical properties make titanium alloys essential structural materials in aerospace. Resistance spot welding (RSW) has high efficiency and cost-effective and is widely used in titanium joining. However, the exceeded welding penetration and coarse martensite α′ limit the mechanical properties of titanium welds. This paper implemented an external magnetic field (EMF) in the RSW process of Ti-2Al-1.5Mn titanium alloy, with detailed investigations into microstructure and mechanical properties. It was found that the penetration rate was reduced, and the nugget diameter was increased under the EMF. Moreover, the coarser columnar prior β grains (PBGs) and martensite α′ formed in traditional RSW transformed into the equiaxed PBGs and widmannstatten structure with α colonies. Due to the significantly improved microstructure and larger nugget diameter, the lap-shear properties were also improved.

High-Energy–Density Fiber Supercapacitors Based on Transition Metal Oxide Nanoribbon Yarns for Comprehensive Wearable Electronics

AbstractFiber supercapacitors (FSs) based on transition metal oxides (TMOs) have garnered considerable attention as energy storage solutions for wearable electronics owing to their exceptional characteristics, including superior comfortability and low weights. These materials are known to exhibit high energy densities, high specific capacitances, and fast redox reactions. However, current fabrication methods for these structures primarily rely on chemical deposition, often resulting in undesirable material structures and necessitating the use of additives, which can degrade the electrochemical performance of such structures. Herein, physically deposited TMO nanoribbon yarns generated via delamination engineering of nanopatterned TMO/metal/TMO trilayer arrays are proposed as potential high-performance FSs. To prepare these arrays, the target materials were initially deposited using a nanoline mold, and subsequently, the nanoribbon was suspended through selective plasma etching to obtain the desired twisted yarn structures. Because of the direct formation of TMOs on Ni electrodes, a high energy/power density and excellent electrochemical stability were achieved in asymmetric FS devices incorporating CoNixOy nanoribbon yarns and graphene fibers. Furthermore, a triboelectric nanogenerator, pressure sensor, and flexible light-emitting diode were synergistically combined with the FS. The integration of wearable electronic components, encompassing energy harvesting, energy storage, and powering sensing/display devices, is promising for the development of future smart textiles. Graphical Abstract

Recycled Cathodes in Rechargeable Aqueous Batteries as Ready-Made Electrodes for Oxygen Evolution Catalysis.

The development of a low-cost and efficient oxygen evolution reaction (OER) electrode is of critical importance for water electrolysis technologies. The general approach to achieving a high-efficiency OER electrode is to regulate catalytic material structures by synthetic control. Here we reported an orthogonal approach to obtaining the OER electrode without intentional design and synthesis, namely, recycling MnO2 cathodes from failed rechargeable aqueous batteries and investigating them as ready-made catalytic electrodes. The recycled MnO2 cathode showed very little Zn2+ storage capacity but surprisingly high OER activity with a low overpotential of 307 mV at 10 mA cm-2 and a small Tafel slope of 77.9 mV dec-1, comparable to the state-of-the-art RuO2 catalyst (310 mV, 86.9 mV dec-1). In situ electrochemical and theoretical studies jointly revealed that the accelerated OER kinetics of the recycled MnO2 electrode was attributed to the enlarged active surface area of MnO2 and optimized electronic structure of Mn sites. This work suggests failed battery cathodes as successful catalysis electrodes for sustainable energy development.

Eco-friendly, lightweight, and high-strength sandwich corrugated particleboard from tea oil camellia (Camellia oleifera Abel.) shells

This study investigates the potential of developing corrugated panels from tea oil camellia shell (TOCS), an abundant agricultural waste in the southern provinces of China, with an annual production of approximately 4 million tons, using experimental and computational methods. Hence, various corrugated geometries were designed using AutoCAD software, and finite element analysis (FEA) was conducted using Ansys Mechanical software to optimize the panel geometry based on TOCS engineering data. Bending performance simulations revealed that a trapezoidal geometry with a 3 mm edge radius exhibited superior bending performance. Therefore, this geometry was selected to fabricate corrugated panels of different densities to assess the impact of density variation. Mechanical characterization included evaluation of bending stiffness, maximum moment, total deflection, compression strength, ultimate strength, dowel bearing strength, and face screw resistance of the panels was performed. Furthermore, specific energy absorption and failure mechanisms of mechanical tests were analyzed. The results indicate that TOCS-based sandwich panels, characterized by their lightweight and sustainable nature, not only meet, or exceed the criteria specified in APA PS 2–10 for use as structural materials but also mitigate the environmental hazards associated with landfill disposal or burning of agricultural waste.

Natural Fiber-Reinforced Mycelium Composite for Innovative and Sustainable Construction Materials

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcases a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composites for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the applicability of mycelium-based materials has extended beyond their original domains of biology and mycology to architecture.

Inorganic Metal Thiocyanates.

Metal thiocyanates were some of the first pseudohalide compounds to be discovered and adopt a diverse range of structures. This review describes the structures, properties, and syntheses of the known binary and ternary metal thiocyanates. It provides a categorization of their diverse structures and connects them to the structures of atomic inorganic materials. In addition to this description of characterized binary and ternary thiocyanates, this review summarizes the state of knowledge for all other binary metal thiocyanates. It concludes by highlighting opportunities for future materials development.

Intelligent Monitoring System for Integrated Management of Historical Buildings

This study demonstrates the effectiveness of a multi-method approach for the restoration of a historic building (train station) in Poland. The project employed field investigations, laboratory analyses, and close-range photogrammetry to create a Historic Building Information Model (HBIM). This comprehensive data set informed the development of targeted conservation strategies that addressed the station’s specific needs while respecting its historical significance. Interventions prioritized the use of locally sourced and sustainable materials, minimized the visual impact on the exterior, and achieved net-zero emissions through improvements to the building envelope and a switch to a heat pump heating system. Additionally, an intelligent monitoring system was implemented to continuously collect data on environmental conditions and structural displacement. These data will be used to develop a predictive model for future maintenance needs, allowing for a preventative approach to conservation and minimizing resource consumption. Overall, this project serves as a model for integrating advanced technologies in historical building conservation, promoting sustainable practices, and ensuring the longevity of irreplaceable cultural landmarks. The key findings derived from this approach encompass a comprehensive assessment of the station’s condition, optimized conservation strategies, insights from HBIM modeling, and the ongoing benefits of the intelligent monitoring system. Field investigations revealed several areas of concern, such as structural cracks, material deterioration, moisture infiltration, and significant heat loss through the building envelope. This information was crucial for developing targeted conservation strategies. The use of internal thermal insulation systems, particularly capillary active mineral blocks, significantly improved thermal performance. Moisture management interventions, including the restoration of the rainwater drainage system and the application of moisture-proof insulation, reduced reliance on the municipal water supply. The intelligent monitoring system, with sensors measuring temperature, humidity, and structural displacement, plays a crucial role in ongoing conservation efforts. This system allows for continuous monitoring and the development of predictive models, ensuring targeted and preventative maintenance, reducing resource consumption, and extending the lifespan of the building.

Preliminary tritium transport analysis for the water cooled ceramic breeder blanket system based on a system level code

This paper presents a dynamic analysis tool for evaluating the tritium inventory, tritium extraction and tritium losses for the Water Cooled Ceramic Breeder (WCCB) blanket system of Chinese Fusion Engineering Test Reactor (CFETR). We have developed a program for the tritium transport analysis at the system level, which aims to estimate the tritium related quantities for the WCCB blanket system. The tritium inventory in the material defects is likewise taken into account. The sensitivity analysis is conducted on key parameters is carried out. The key output quantities of the WCCB blanket system include the tritium inventory in structural material, purge gas and coolant loops, tritium extracted by the TES and CPS, and tritium losses.

Localized surface plasmon-enhanced nanorod micro-LEDs with Ag nanoparticles embedded in insulating and planarizing spin-on glass

To enhance the emission of GaN-based Micro-LEDs (μLEDs), we etched uniform nanorods (NRs) on the μLED surface and filled the nanorod gaps with spin-on glass (SOG) containing mixed Ag nanoparticles (NPs). The nanorod structure creates a conducive environment for close interaction between Ag NPs and quantum wells (QWs), facilitating the coupling of Ag NPs as localized surface plasmons (LSPs) with the QWs to enhance light emission. The SOG acts as an insulating layer between Ag NPs and NRs, preventing electron leakage, while also serving as a planarization material for the nanorod structure. This configuration allows for the fabrication of a planar Indium Tin Oxide layer without short-circuiting the nanorod structure. Compared to traditional planar Micro-LEDs, NR-μLEDs with SOG-encased Ag NPs exhibit a 50% increase in electroluminescence (EL) intensity and a 56% increase in photoluminescence (PL) intensity. This work paves the way for broader applications of LSP in μLEDs.

Electroluminescence from pure resonant states in hBN-based vertical tunneling junctions

Defect centers in wide-band-gap crystals have garnered interest for their potential in applications among optoelectronic and sensor technologies. However, defects embedded in highly insulating crystals, like diamond, silicon carbide, or aluminum oxide, have been notoriously difficult to excite electrically due to their large internal resistance. To address this challenge, we realized a new paradigm of exciting defects in vertical tunneling junctions based on carbon centers in hexagonal boron nitride (hBN). The rational design of the devices via van der Waals technology enabled us to raise and control optical processes related to defect-to-band and intradefect electroluminescence. The fundamental understanding of the tunneling events was based on the transfer of the electronic wave function amplitude between resonant defect states in hBN to the metallic state in graphene, which leads to dramatic changes in the characteristics of electrons due to different band structures of constituent materials. In our devices, the decay of electrons via tunneling pathways competed with radiative recombination, resulting in an unprecedented degree of tuneability of carrier dynamics due to the significant sensitivity of the characteristic tunneling times on the thickness and structure of the barrier. This enabled us to achieve a high-efficiency electrical excitation of intradefect transitions, exceeding by several orders of magnitude the efficiency of optical excitation in the sub-band-gap regime. This work represents a significant advancement towards a universal and scalable platform for electrically driven devices utilizing defect centers in wide-band-gap crystals with properties modulated via activation of different tunneling mechanisms at a level of device engineering.

Topological hydrogen-bonded organic frameworks (HOFs) and their electronic applications in sensor, memristor, and neuromorphic computing

Recently, an emerging class of hydrogen-bonded organic frameworks (HOFs) has become an appealing member of organic material family, attributed to their layered self-assembly structures, high-crystalline, and environmentally friendly characteristics, which have rapidly propelled their development in the field of electronic devices. In this context, we focus on the latest category of topological HOFs, with particular attention given to cutting-edge experimental demonstrations, exceptional electrical performances, and promising applications. First, a concise concept and fundamental mechanism of HOFs are provided, elucidating the potential correlation between structural designs and material properties. Subsequently, a comprehensive summary is presented on the preparation and synthesis methods, such as hydrothermal techniques, epitaxial growth, electro-deposition, among others. Notably, the latest advancements in HOFs-based electronics are thoroughly introduced and discussed, along with their applications in sensors, memristors, artificial synapses, neuromorphic computing, and human perception systems. Finally, the future challenges and prospects of topological HOFs are elaborated upon with the aim of providing valuable guidance for high-performance HOF-based electronics.

Gendering Zoom Diplomacy: Women’s Participation in Digital Diplomacy

Abstract In the wake of the COVID-19 pandemic and the subsequent emergence of “Zoom diplomacy,” scholarship on digital diplomacy has shifted attention from the nexus between social media and foreign policy to exploring the use of digital technologies in diplomatic encounters. While these studies have generated important insights on the affordances and limitations of digital diplomacy, we know much less about the impact of digitalization on the gendered hierarchies and power dynamics that characterize diplomatic practices. In what ways does digitalization of diplomacy shape these hierarchical and gendered practices of diplomacy? In taking stock of recent empirical findings on digital diplomacy, the analysis reviews the varied effects of digitalization on women’s diplomatic agency. Focusing on peace diplomacy, it suggests that digitalization of diplomacy produces ambivalent agency where digitalization opens up some opportunities for disrupting gendered diplomatic practices, but within patriarchal gender structures. The analysis highlights the ways in which digital diplomatic agency and competence are shaped by gendered material and normative structures, suggesting that on the borders of what is conventionally regarded as diplomacy, digitalization may be reinforcing diplomacy as a masculine practice.