Sinusoidal Pulse Width Modulation Research Articles

A comparative study of virtual synchronous generator and sinusoidal pulse width modulation in a wind high power conversion chain

The virtual synchronous generator (VSG) and sinusoidal pulse width modulation (SPWM) are two prominent control strategies that have attracted particular interest recently. In this paper, we compare these two inverter control strategies in a 5MW wind power conversion chain. The studied conversion chain includes a wind turbine, a permanent magnet synchronous generator, the power converters, namely the uncontrolled rectifier, and a two-stage inverter connected to the grid via an LCL filter. Our study of the two control methods shows that both strategies reduce the total harmonic distortion (THD) while respecting the grid connection conditions. The simulation results manifest that the VSG strategy has a better THD reduction of 0.99 % which is improved compared to the SPWM with a THD of 1.33%.

Renewable Power Energy Management for Single and Three-phase Inverters Design

This study manages solar panels, wind turbines, and fuel cells to develop single- and three-phase Sinusoidal Pulse Width Modulation (SPWM) inverter circuits. The maximum power point tracking method in direct current (DC)-DC boost converters efficiently uses these renewable sources. Photovoltaic (PV), wind turbines, fuel cells, and bidirectional batteries are utilized in energy management. Efficiency, material cost reduction, and user convenience depend on energy management. The technology fully charges the standby battery when all sources are available. Other renewable sources will power the system if one fails. Before boost converter circuits, renewable energies generated 310V for PV, 60V for wind energy conversion, 215V for fuel cells, and 25.9V for bi-directional batteries. Proportional-integral (PI) controllers govern inverter switching to maintain high-quality sinusoidal outputs while decreasing total harmonic distribution (THD). Single-phase load voltage and current at resistive load have 0.65419% THD. Load voltage and current root main square (RMS) values are 217.3617 (V) and 3.1052 (A), respectively. When connected to an R load, the three-phase inverter circuit provides 1.5146% THD for load voltage and current. Load voltage and current RMS readings are 218.4261 (V) and 2.1843 (A). THD is 1.5969% for load voltage and 1.2905% for load current with an RL load. In this example, load voltage and current RMS values are 214.201 (V) and 2.0916 (A). Simulations demonstrate the successful integration of renewable sources to meet energy needs and maintain power supply. The above solutions use renewable energy efficiently and integrate with the grid.

Z source based switched capacitor nine level boost inverter with a modified modulation strategy

This article presents a Z source (ZS) based switched capacitor multilevel inverter (SC-MLI) with low capacitors charging inrush currents utilizing a modified modulation strategy. The topology generates nine output voltage levels with quadruple voltage gain utilizing eight power switches, five capacitors, two inductors, four discrete diodes, and a single DC source. The voltage gain can be further increased by applying shoot through (ST) states to the frontend ZS-network. Owing to its high voltage gain, the topology is suitable for low voltage renewable energy sources such as photovoltaics (PV), and fuel cells (FC). A modified modulation strategy is presented based on the conventional level shifted sinusoidal pulse width modulation (LS-SPWM). The proposed modulation strategy improves the dc-link utilization at higher modulation index. A detailed mathematical analysis is provided for the gain calculation based on the modified modulation strategy. A comparative study is implemented to verify the merits of the proposed topology. A simulation model is implemented utilizing MATLAB / Simulink to verify the topology characteristics. The power losses and efficiency calculations are presented using Altair PSIM. Furthermore, an experimental prototype is constructed to verify the simulation findings. The topology is tested with different loading conditions at numerous modulation index values and ST duty ratios. Furthermore, step change conditions are implemented to test the topology response. The effect of the ZS network on the switched capacitors charging inrush currents is validated. The proposed topology shows an overall advantage in terms of the output characteristics as well as the hardware requirements.

Design and Verification of Multiphase Multilevel Traction Inverter

The paper presents the practical design and implementation of a three-level neutral point clamped (TNPC) six-phase inverter rated at 100 kVA. The study initiates with prior work review, whereby most research work done earlier was mainly simulation-based. Based on the simulation results, this paper focuses on the practical aspects of inverter design, such as the development of a power board on an Insulated Metal Substrate, a gate driver board, an interconnect board, and the main control board. An inverter physical prototype has been built and tested at 500 V and 20 kW of output power. The SiC semiconductor technology is the base of the inverter, which represents the main merit of the work. Finally, high power density, compact design, and high efficiency are shown, which are major contributions of the paper. Tests performed proved that the designed converter was operating reliably and efficiently. While a simple Sinusoidal Pulse Width Modulation (SPWM) control algorithm has been implemented, the overall performance of the inverter showed great promise for higher-power applications. Compact and high-efficiency TNPC converters are developed for meeting increasing demands of advanced energy, automotive, and industrial applications.

Design and verification of monitoring system of DC microgrid based on Ethernet communication

AbstractReal‐time acquisition of microgrid (MG) operation data and remote control play a crucial role in the safe and stable operation of MG. A design scheme of monitoring system is proposed for the wind/photovoltaic/energy storage islanded direct current MG. The core controllers used in direct current MG system are programmable logic controller and digital signal processor. The monitoring system mainly adopts Ethernet communication, together with serial port communication mode Recommend Standard 232 (RS232) and Recommended Standard 485 (RS485) communication modes. A heterogeneous networking is built with controllers and data display instruments. Different monitoring interfaces are designed, the important information can be real‐time detected, collected and displayed. The multi‐energy and multi‐load dispatching operation control are realized according to scheduling operation plan. The parameters of the inverter can be adjusted, and the output voltage waveform and sinusoidal pulse width modulation waveform of the inverter can be measured. The communication of the proposed monitoring system is reliable, flexible and expandable, and easy to realize remote operation control. Moreover, the detection and control functions can be extended further. Through experiments, the effective control and monitoring of the designed monitoring system is verified, and the intelligent management is realized.

Inverter Practical Module Design for Power Electronics Course in Electrical Engineering Education Study Program

Inverter material is one of the essential materials in power electronics courses. An inverter is an electronic device that converts direct current (DC) into alternating current (AC). This concept is the foundation of electronics. Because the power electronics course is a practicum course, a practicum module is required as an intermediary teaching medium; this practical module discusses 3-phase inverter material, which uses the pulse width modulation (PWM) and sinusoidal pulse width modulation inverter (SPWM) switching methods. Through Tinkercad software, the circuit is assembled, and the output wave results from the two methods used are seen in designing the 3-phase inverter practical module using the Research and Development method. This research uses media and material validation sheet instruments to determine the feasibility of the 3-phase inverter practicum module. The research results showed that the percentage of media experts was 94%, material experts were 81%, and language experts were 84%. Hence, the 3-phase inverter practicum module is very suitable for use and can make it easier for students to understand inverters. Thus, developing a 3-phase inverter practicum module can effectively increase students' understanding of inverter material and interest in learning. It can also be an alternative for lecturers in teaching.

Improve power quality and stability of grid - Connected PV system by using series filter

As the world increasingly focuses on renewable energy sources, grid-connected PV systems will continue to play a critical role in meeting our energy needs. This integration has brought many benefits, but has also created various problems related to power quality and stability at the connection points. Various techniques are used to improve the power quality, such as passive filters, tuned passive harmonic filters, and active filters. This paper presents the use of a series active filter on the DC side of grid-connected PV systems to improve their power quality, stability, and dynamic performance. The proposed filter consists of an inductor, two capacitors, and four transistor-diode pairs, the operation of which is controlled by a sinusoidal pulse width modulation (SPWM) scheme. The MATLAB/Simulink is used to build and validate a comprehensive mathematical model of the studied system. The transfer function of the system is identified and its transient response is studied under various test input signals. A Bode plot is also generated to assess the impact of the integration of this component on the stability of the system. The results showed that incorporating the filter resulted in a significant reduction in the total harmonic distortion factor (Thd%) for both the voltage and current waves at the inverter output. Moreover, it improved the transient response characteristics of the system by significantly reducing the maximum overshoot value of the system response with respect to the test input signals. The results indicate that the stability of the system is improved after the filter addition, as evidenced by the increased gain margin and phase margin in the system Bode plot.

Phase disposition PWM control topology based: A novel multilevel inverter with reduced switch for power electronics applications

In the field of industrial drive applications, a neutral point clamped multilevel inverter (NPC MLI) is an extensively used option. The NPC MLI architecture involves more number of components for higher level and higher switching frequency operation. In this work paper, a novel three-phase 3-Level MLI is proposed evading the usage of clamping diodes and quadratic switches. Additionally, phase disposition pulse width modulation (PD-PWM) control technique is also employed for the proposed MLI. In comparison to NPC MLI, proposed MLI reduces the voltage switching stress as only one switch is operated per inverter leg. Another feature is that there is a considerable reduction in power losses as the current flows only through fewer elements. The proposed 3L inverter topology is explored thoroughly using the MATLAB simulation model. The evaluation of results is also demonstrated concerning the proposed PD-PWM technique by comparing its performance with the conventional sinusoidal PWM method. The Real-Time hardware-in-loop (HIL) simulator is also used to validate the simulation outcomes of the proposed model.

Sinusoidal PWM Generation for 3 Phase Inverter and RPM Measurement using Hercules TMS570LC43xx Launchpad

This project focuses on implementing a 3 phase Sinusoidal PWM generation using the Hercules TMS570LC43xx Launchpad Development Kit (Launchpad). The primary objective is to generate synchronized Sinusoidal nature PWM signals using the onboard High-End Timer (HET) and Enhanced Pulse Width Modulation (ePWM) module, which can be given to the Inverter for conversion of Direct current (DC) power into Alternating current (AC) power. This conversion is essential in various applications where AC power is required but the power source provides DC power. It is used in Solar photovoltaic (PV) systems and other renewable energy installations. These systems generate power suitable for powering household appliances or feeding into the electrical grid. Itis alsoused in electric vehicles (EVs) to drive the electric motor with variable speed. For verification of the wave nature, we have used an external lowpass filter (LPF) to transform the dynamic PWM signals into sinusoidal waveforms, ensuring compatibility with various applications like Inverters which can be further used in equipment and machinery such as Brushless DC motors, pumps and compressors. With the addon functionality to control the signal’s frequency which will be given to the Inverter to control the speed of the motor. Additionally, the project incorporates RPM measurement of the motor using an optical encoder setup interfaced with the Enhanced Quadrature Encoder Pulse (eQEP) module on the Launchpad. This feature enables accurate measurement of rotational speeds, position and Revolution per minute (RPM), enhancing the functionality of the system in real world applications like the speed of conveyor belts and other automated transport systems. Through successful implementation, this project demonstrates wide control for the Inverter, achieving reliable synchronized 3 phase signals with its variable speed having 120-degree phase shift signals alongside precise RPM measurement. The project highlights the Launchpad’s capabilities in handling complex signal processing tasks essential for modern power electronics applications. Looking forward, this project establishes a foundation for future enhancements and innovations in power electronics.

Research on Underwater Constant High-Voltage DC Switching Technology for MCSEM.

The marine controlled source electromagnetic (MCSEM) transmitter can transmit high currents near the seabed to detect the electrical structure of the seafloor. The use of three-phase alternating current (AC) transmission can lead to three-phase imbalance, which results in an excessive current in one phase's power line and affects the safety of the tow cable. This paper proposes an MCSEM underwater constant high-voltage direct-current (DC) switching scheme that replaces AC transmission with DC transmission. This scheme can fundamentally avoid three-phase imbalance and the AC loss caused by inductance. After establishing a simulation model to analyze the effect of the scheme, the relevant hardware units were designed. The hardware unit mainly consists of three parts: a DC switching inverter unit, a filter unit, and a step-down rectification unit. The DC inverter unit controls six insulated gate bipolar transistor (IGBT) modules with sinusoidal pulse width modulation (SPWM) signals to convert DC to three-phase AC power; the filter unit filters out extra harmonic components; and the step-down rectification unit converts high-voltage three-phase AC to low-voltage DC. The scheme ultimately achieved an adjustable DC output of 48.3-73.4 V under a constant DC input voltage of 3000 V and effectively reduced the current on the cable. This scheme has the potential to replace the previous AC transmission, reducing the risk of tow cable burnout and enhancing the safety of MCSEM operations.

IMPROVING THE QUALITY OF THE 3-PHASE INVERTER USING A 5-LEVEL NEUTRAL POINT CLAMPED INVERTER TECHNIQUE COMBINED WITH THE SINUSOIDAL PULSE-WIDTH MODULATION

The use of renewable energy sources is a global trend, aiming to limit the use of fossil energy sources that pollute the environment. Inverters are very important devices used in renewable energy conversion systems. Therefore, improving the quality of inverters isan issue that is receiving a lot of attention and research. This paper focuses on the solution to improve the quality of 3-phase inverters using the neutral point clamped (NPC)-5 level inverter technique combined with the sinusoidal pulsewidth modulation (SinPWM) technique. One of the highlight points of this study is that it has successfully reduced the number of switching times and eliminated the common-mode voltage (CMV). The simulation results have shown that the proposed technique has achieved excellent and feasible results, thereby the inverter quality is significantly improved.

Analysis, design, and implementation of a simple switched‐coupled‐inductor boost DC‐AC inverter

AbstractThis paper presents a simple switched‐coupled‐inductor inverter (SCII), as well as completes the relevant analysis, design, and implementation, for efforts aimed at achieving boost DC‐AC inversion and strengthening closed‐loop regulation. In structure, the power‐part circuit consists of switched‐coupled‐inductor booster and half‐bridge DC‐link inverter, connected in cascade between supply and output to work for the AC output range as (n: turn ratio, : ratio cycle). As adopting , , , the output can be lifted to (i.e., DC 24 V to AC 100 Vrms, 60 Hz). In control, the control‐part circuit consists of phase generator and sinusoidal pulse‐width‐modulation (SPWM) block and generates driver signals of switches according to the feedback signal of for the needs of timing sequence (to different topologies) and output regulation/robustness (to various desired output/loading variation). The related chip circuit is designed via pre‐/post‐layout Cadence procedure and then practically is implemented on a real chip (D35‐106B‐E0027, TSMC 0.35 μm, 1500 × 1500 μm2, 3.3 V, 2.146 mW, 100 kHz max., 18S/B) via the assistance of TSMC and Chip Implementation Center (CIC). In theory, some relevant analysis and design will be discussed, such as modeling, conversion ratio, power efficiency, parameter selection, system stability, and control design. In implementation, several simulation/experiment cases via testing on the SCII's prototype circuit are illustrated to examine the efficacy of the proposed scheme.

An Improved SPWM Strategy for Effectively Reducing Total Harmonic Distortion

In the inverter circuit, the speed at which the MOSFET is impacted by the presence of a parasitic inductor within the printed circuit board (PCB) leads to a delay in the switching process. Furthermore, the parasitic inductor within the circuit can easily form an LC oscillation with the parasitic capacitor of the MOSFET. These two issues result in an inconsistency between the actual output of the MOSFET and the driving signal waveform, leading to distortion in the sinusoidal pulse width modulation (SPWM) waveform and an increase in total harmonic distortion (THD). It is a common practice to mitigate gate oscillation by introducing a resistor at the gate of the MOSFET. However, elevating the resistance leads to deceleration in the charging process of the MOSFET’s parasitic capacitor, consequently causing an increase in the switching delay, and thereby increasing THD. Therefore, an effective strategy to reduce THD is proposed in this paper, while augmenting the gate resistance, computing the MOSFET switching delay, and applying corrective compensation. In this way, the inherent issues of the switch are addressed, resulting in inverter output waveforms that closely resemble sine waves and reduced THD. Through a combination of simulation and empirical experimentation, the efficacy of the proposed approach in significantly reducing THD in the inverter’s output waveform has been empirically substantiated.

Wild horse optimization algorithm implementation in 7-level packed U-cell multilevel inverter to mitigate total harmonic distortion

Introduction. Multilevel inverters (MLIs) are a popular industrial and, more especially, renewable energy application solution. This is because of its appetite for filters, low distortion class, and capacity to provide a multilayer output voltage that resembles a pure sine waveform. The novelty is in applying the wild horse optimization algorithm (WHOA) to adjust the sinusoidal pulse width modulation (SPWM) technique by producing the optimal reference signal parameters in a new multilevel inverter architecture known as the packed U-cell multilevel inverter (PUC-MLI). Purpose. This study helps with the idea of new inverter architecture and a modified pulse width modulation (MPWM) method to make the multilevel inverter smaller, cheaper, and with less total harmonic distortion (THD). Methods. We use the proposed approach to control a 7-level, single-phase PUC-MLI. The WHOA is used to discover the optimal parameters of the additional reference sine signal after being compared with SPWM to evaluate its performance in harmonic reduction. The simulation’s outcome was validated by building a PUC-MLI prototype. Results. Experimental results and simulations validate the effectiveness of the suggested approach. The WHOA-improved MPWM approach achieves a significant reduction in THD on the PUC-MLI output voltage, as indicated by the results. Practical value. THD in MLI output voltage will be reduced without spending any cost. The suggested solution works with many MLI topologies with varying output voltage levels. References 20, tables 6, figures 12.

Comparative harmonic elimination techniques for supraharmonic reduction in microgrid

In order to reduce voltage distortion and supraharmonic (SH) emission in microgrid (MG) systems with electric vehicle (EV) charging stations, this research compares several harmonic elimination approaches. The increasing deployment of EVs has led to the integration of EV charging stations within MG systems, presents challenges in maintaining a high power quality (PQ). Voltage distortions and SH emissions are caused due to non-linear loads and the intermittent nature of EV charging, which have an effect on the performance and dependability of the MG. In order to solve these problems, multilevel converters (MLCs) are used to produce high-quality waveforms. MLCs use harmonic elimination methods to cut down on SH emissions, which improves the PQ overall. Sinusoidal pulse width modulation (PWM), selective harmonic elimination (SHE), space vector modulation (SVM), and random-PWM (RPWM) techniques are among the harmonic elimination methods compared and analyzed. The results will enable the selection of the most appropriate strategy for minimizing voltage distortion and SH emission in MG systems, while providing valuable insights into the effectiveness of each method.

Buck–Boost DC–AC converter based on coupled inductors

In this paper, a single stage buck–boost DC–AC converter based on coupled inductors is presented for renewable energy and electric vehicle applications. The proposed topology works with only three semiconductor switches, two diodes, and three coupled inductors to transfer input DC voltage to a high gain or low gain output AC voltage. A coupled inductor is used instead of normal inductors, which will reduce core and size requirements. The sinusoidal pulse width modulation strategy is used in this paper for controlling the main switch. There are many merits in the presented topology, like high gain up to five times of input voltage, compact size, less number of components, which results in reducing the overall cost, reducing switching loss, and increasing the converter efficiency. The simulation study is carried out using MATLAB/SIMULINK to simulate the operation of the proposed converter. Also, an experimental setup is built up to examine the actual operation of the proposed converter. There is a good agreement between simulation and experimental results which increases the validation and confidence of the model.

IEZ-Source Inverter Topology with Tuned PID Controller of Carrier SPWM Technique in Grid Connected System

Z-source inverters are used in controller applications, which offer higher performance than the buck-boost converter. This work presents the Improved Embedded Z (IEZ)-source inverter used for the impedance network. The Z-source inverter includes the switching topologies, so the double inductor is added to the EZ source inverter circuit. IEZ source inverter manages the Total Harmonic Distortion (THD), and the PID controller controls the inverter voltage. The Social Ski Driver (SSD) Optimization algorithm is used to tune the parameters of the PID controller. The harmonic content of the Z-source inverter is reduced by the carrier based sinusoidal Pulse Width Modulation (SPWM) technique. The Improved Embedded Z-source Inverter (IE-ZSI) is utilized to apply a grid-connected system. The inverters receive the power from the DC voltage and supply the grid-connected load with controllable voltage. The proposed work is implemented in the platform MATLAB/SIMULINK to evaluate the performance of the voltage across the capacitor, the voltage across the inductor, grid current and grid voltage. Inverter DC link voltage performance was compared to conventional Z-source inverters and embedded Z-source inverters. The proposed work achieved 1.52% THD compared with existing techniques.

Comparative Study of TLP250 and IR2132 Driver-Based Inverter for Induction Motor Driving

As time progresses, electric motors are used for industrial or commercial purposes. The need for a motor that is robust, simple, and easy to maintain has been answered by creating an induction motor that can handle the purpose. At the beginning of its use, induction motors were more often used at constant speeds. Using an inverter becomes one of the solutions at hand to control the induction motor. Nowadays, most inverters are controlled by the SPWM (Sinusoidal Pulse Width Modulation) method. This method can adjust the output voltage and frequency by setting the carrier signal's frequency value and the reference signal's amplitude. A driver circuit is needed to implement an SPWM-based inverter. This driver circuit is needed to isolate the power circuit from the controller. Moreover, this circuit is also used to increase the microcontroller output signal to trigger the IGBT gate switch. The IR2132 and TLP250 drivers are often used in three-phase inverter applications. These drivers have advantages and disadvantages. This paper discusses the capabilities of these two drivers when applied to a three-phase inverter that functions as an induction motor drive. This inverter-controlled induction motor is advantageous because it can be rotated at a nominal speed and frequency.

APPLICATION OF SOFT SWITCHING IN THREE-PHASE VOLTAGE INVERTERS OF TRACTIONAL ROLLING STOCK

Autonomous voltage inverters with PWM, which are used in electric drive systems with brushless motors, occupy an important place in the complex of electrical equipment of modern traction rolling stock of railways. The article presents the results of the research of the traction three-phase bridge voltage inverter with soft switching of power switches. Using the soft switching mode allows you to reduce the switching losses in the power transistors of the keys, increase the PWM frequency and improve other performance indicators of the converter. It is advisable to implement soft switching in the key transistors of the three-phase voltage inverter using soft switching nodes with fast-acting four-quadrant switches based on IGBT. It is proposed to consider the possibility of using transistor switches of a voltage inverter with capacitive non-dissipative snubbers at high PWM frequencies. For this purpose, a synthesis of the scheme and algorithm for the implementation of soft switching in a three-phase bridge voltage inverter with bipolar sinusoidal PWM with soft switching nodes with high-speed four-quadrant switches based on IGBT was performed. An analysis of the characteristics of the three-phase voltage inverter was carried out when using high-speed switches in the soft switching nodes to implement soft switching in the power transistors of the inverter switches.On the basis of the study, it is proposed to modernize the scheme of the soft switching unit in order to provide better preparation for the switching of the power transistors of the keys at large load currents. The improved soft switching unit includes low-voltage sources of constant voltage, which will compensate for energy losses in the recharging circuit of the snubber capacitors and contribute to the soft switching on of the power transistors of the voltage inverter keys. The performance test was carried out and the characteristics of the converter were analyzed when using a modernized soft switching node using simulation modeling in the MATLAB package.

Assessment of vertical shifted carrier schemes for sinusoidal pulsewidth modulation

Assessment of vertical shifted carrier schemes for sinusoidal pulsewidth modulation