Single-mode Research Articles

New energy levels of atomic holmium discovered by laser spectroscopy in the near infrared spectral range

A combination of optogalvanic spectroscopy and laser-induced fluorescence spectroscopy with a continuous wave tunable single mode Ti-Sa laser was applied to find new energy levels of atomic holmium. Free and excited holmium atoms were produced in a liquid nitrogen-cooled hollow-cathode lamp. In this study, we examined 35 spectral lines of Ho I in the near-infrared wavelength range from 698 nm to 833 nm. Altogether, 16 new energy levels have been discovered, 5 levels of even parity and 11 levels of odd parity. Another four energy levels have been discovered but have already been published by another research group. Data on the hyperfine structure for the new levels are presented. Additionally, hyperfine structure data of three known levels of even parity were determined for the first time. The existence of the new energy levels was confirmed by analyzing 60 lines of previously measured Fourier transform spectra to precisely determine the energy of the levels.

Optical spectra in pure-silica-core single mode optical fibers after high-fluence reactor irradiation

The paper describes the study of radiation-induced attenuation (RIA) spectra in reactor-irradiated single mode optical fibers (OFs) with differente high-temperature coatings (polyimyde, aluminum and copper). The OFs were previously irradiated up to fast neutron fluence 1.8·1020 n/cm2 and gamma dose 2.32 GGy. After three years of annealing at room temperature (RT), the RIA spectra were examined within the range of 650–1700 nm. All RIA mechanisms acting within this spectral range were identified: absorption bands attributed to non-bridging oxygen hole centers, a long-wavelength (LW) band with a maximum at λ > 1800 nm, and unsaturated “grey” loss due to coating microbendings or damage. It was found out that RIA asocciated with the LW band can be significantly annealed at room temperature in polyimide-coated OFs. RIA mechanisms influenced by the coating were found to be more stable than those causing LW-RIA.The LW-RIA arising during reactor and gamma irradiation exhibits a similar shape, approximated by the Kubo-Greenwood formula for alternative conductivity, which describes the absorption of self-trapped holes (STH) and exibits close thermal stability at RT. This suggests a STH-like nature of LW-RIA. The accurate approximation of the RIA spectrum in the near-infrared range requires considering contributions of the unsaturated loss or contributions of an absorption band peaking at an energy of 1.33 eV with a half-width of 0.45 eV.

A robust and accurate feature matching method for multi-modal geographic images spatial registration

ABSTRACT While the current research has achieved satisfactory results for the registration of single mode data, there has always been a significant challenge in the registration of multi-modal images due to the obvious nonlinear radiation differences caused by different imaging mechanisms and imaging time. For example, multi-temporal visible, visible-synthetic aperture radar, visible-near infrared, near infrared-short wave infrared, visible-MAP, etc. To address this problem, we propose a Robust and Accurate Feature Matching Method for Multi-modal Geographic Images Spatial Registration (RAMMR) to fully extract common key points between images, weaken the radiation difference between data, and finally accurately match more inliers to realize multi-modal image registration. Considering the influence of noise and edge information on key point extraction, RAMMR first constructs a new scale space by introducing the Side Window Filter (SWF); Then, we improve Harris algorithm to extract key points based on the SWF scale space; After that, we propose an enhanced log-polar descriptor based on the gradient angles and gradient amplitudes of the scale space, which effectively improves the quality of the descriptor and avoids the mismatch of key points; Based on the standard Euclidean distance, we design a re-match strategy to obtain the initial matching results, and Random Sample Consensus (RANSAC) is used to eliminate outliers. Finally, the affine transformation parameters are calculated based on inliers, and multi-modal image registration is realized. RAMMR is evaluated on different multi-modal datasets and compared with some state-of-art methods. The experimental results show that RAMMR accurately registers multi-modal geographic images and obtains comparative results compared with benchmark methods. Our source datasets are publicly available at https://github.com/RSmfmr/multimodal-dataset.

"Intelligent tutoring effects on induced emotions and cognitive load of learning-disabled learners".

This study addresses the learning requirements of learners with learning difficulties by monitoring their learning experience in an Intelligent Tutoring System. Intelligent Tutoring Systems were developed to enrich the teaching-learning process. In the present work, the interface is designed and developed utilizing the potential of Artificial Intelligence to meet their individual needs. Designing an online learning platform for a learners with learning difficulties requires consideration of their learning problems and preferences. The interface was developed focusing on all the requirements of the LD learners. The objective of the present study is to monitor the learning experience in the form of induced emotions and cognitive load of the learners to determine the impact of learning. 83 learners were observed during various stage of learning. The results obtained through the Support Vector machine (SVM) classification technique showed the positive attitude towards intelligent tutoring. The analysis revealed that a total of 0.23% of learners were positively induced. Their learning experience was positive and effective. The cognition load on learners was minimum with single-mode instruction and least disturbed. The system was improved based on preference feedback on design features. This helps in improving content design and creating device independent and responsive visual design. The fatigue effect analysis on cognitive load implied that multiple modes of instruction increased drowsiness. Single mode of instruction have a positive impact on the learning process and it reduces the cognitive load of the learners.Implications for RehabilitationThe user interface designed and developed for learners with Dyslexia, Dysgraphia and Dyscalculia has learning disabled-friendly features. These can be used to create a device-independent and responsive design.Learning experience is monitored along with the impact on cognitive load of the learners.The research helps in understanding the stimulation and response of learners with learning disability for different learning conditions.Most existing learning systems are limited to non-learning-disabled learners. The ITS developed during research presents a Universal learning design helpful for all learners with and without learning disability.

Stabilization and correction of aberrated laser beams via plasma channelling.

High-power laser applications, and especially laser wakefield acceleration, continue to draw attention through various research topics, and may bring many industrial applications based on compact accelerators, from ultrafast imaging to cancer therapy. However, one main step towards this is the arch issue of stability. Indeed, the interaction of a complex, aberrated laser beam with plasma involves a lot of physical phenomena and non-linear effects, such as self-focusing and filamentation. Different outcomes can be induced by small laser instabilities (i.e. laser wavefront), therefore harming any practical solution. One promising path to be explored is the use of a plasma channel to possibly guide and correct aberrated beams. Complex and costly experimental facilities are required to investigate such topics. However, one way to quickly and efficiently explore new solutions is numerical simulations, especially Particle-In-Cell (PIC) simulations if, and only if, one is confidently implementing such aberrated beams which, contrary to a Gaussian beam, do not have analytical solutions. In this research, we propose two new advancements: the correct implementation of aberrated laser beams inside a 3D PIC code, showing a great consistency, under vacuum, compared to the calculations with Fresnel theory); and the correction of their quality via the propagation inside a plasma channel. We demonstrate improvements in the beam pattern, becoming closer to a single plasma mode with less distortions, and thus suggesting a better stability for the targeted application. Through this confident calculation technique for distorted laser beams, we are now expecting to proceed with more accurate PIC simulations, closer to experimental conditions, and obtained results with plasma channels indicate promising future research.

Spatial and mode selective switch for orbital angular momentum mode division multiplexing

In analogy to a wavelength selective switch in wavelength-division multiplexing (WDM) optical fiber communication systems, a spatial and optical mode selective switch (SMSS) would be an important component in future ultrahigh capacity optical fiber communication systems based on space and mode division multiplexing. In this work, a free-space SMSS for orbital angular momentum (OAM) mode-division multiplexing (MDM) is proposed and experimentally demonstrated. The SMSS consists of a separating part for transforming OAM modes to spatial modes and a recombining part for selecting and recombining the modes to any spatial channel. The SMSS is able to implement strictly non-blocking switching between a total of 36 SDM/MDM channels configured as four spatial channels each supporting nine OAM mode channels.

Advances in High-Power Vertical-Cavity Surface-Emitting Lasers

Abstract Vertical-cavity surface emitting lasers (VCSELs) have emerged as a highly promising light source with extensive applications in various fields, including consumer electronics, optical communication, metrology, sensing and ranging. Their low-cost, high conversion efficiency, and compact footprint make them particularly attractive for widespread adoption. While considerable success has been made in enhancing the performance and speed of VCSELs for optical communications, achieving high-power VCSELs with properties such as high output power, single transverse mode operation, and temperature stability for remote sensing applications remains a challenging endeavor. This review aims to provide a comprehensive overview of the recent advancements in the development of high-power VCSELs. By examining the advancements in active materials, device designs, array configurations, this review seeks to shed light on the current state-of-the-art and potential avenues for further improvement in high-power VCSEL technology.

Effects of inner cone length on continuous rotating detonation in a variable cross-section combustor

A variable cross-section combustion chamber with different inner cone length L is designed, composing of an annular part with divergent width and a cylinder part without inner cone. Ethylene-air and hydrogen-air continuous rotating detonation (CRD) experimental tests are conducted. The results show that the ethylene-air CRD wave can be achieved in the variable cross-section combustor with the short inner cone. The propagation velocity of ethylene-air CRD wave can be 1661.37 m/s with the equivalence ratio of 0.91 and L of 10 mm. With L increasing from 0 mm to 30 mm, the combustion mode varies in the single wave mode, the sawtooth wave mode, and the hybrid mode. The combustor width is not the main factor leading to the failure of detonation in this study. The acceleration of propellent mixture caused by the expansion of the annulus channel, and the downstream movement and reduction of recirculation zone around the inner cone both increase the difficulty in CRD realization. While the hydrogen-air CRD can self-sustain with the intensive reaction zone in the annular part in the critical configuration of ethylene-air CRD. This study will contribute to the understandings of self-sustaining mechanism of CRD in the divergent combustor and the combustor design of the hollow chamber.

High-efficiency self-focusing metamaterial grating coupler in silicon nitride with amorphous silicon overlay

Efficient fiber-chip coupling interfaces are critically important for integrated photonics. Since surface gratings diffract optical signals vertically out of the chip, these couplers can be placed anywhere in the circuit allowing for wafer-scale testing. While state-of-the-art grating couplers have been developed for silicon-on-insulator (SOI) waveguides, the moderate index contrast of silicon nitride (SiN) presents an outstanding challenge for implementing efficient surface grating couplers on this platform. Due to the reduced grating strength, a longer structure is required to radiate the light from the chip which produces a diffracted field that is too wide to couple into the fiber. In this work, we present a novel grating coupler architecture for silicon nitride photonic integrated circuits that utilizes an amorphous silicon (α-Si) overlay. The high refractive index of the α-Si overlay breaks the coupler’s vertical symmetry which increases the directionality. We implement subwavelength metamaterial apodization to optimize the overlap of the diffracted field with the optical fiber Gaussian mode profile. Furthermore, the phase of the diffracted beam is engineered to focalize the field into an SMF-28 optical fiber placed 55 µm above the surface of the chip. The coupler was designed using rigorous three-dimensional (3D) finite-difference time-domain (FDTD) simulations supported by genetic algorithm optimization. Our grating coupler has a footprint of 26.8 × 32.7 µm2 and operates in the O-band centered at 1.31 μm. It achieves a high directionality of 85% and a field overlap of 90% with a target fiber mode size of 9.2 µm at the focal plane. Our simulations predict a peak coupling efficiency of − 1.3 dB with a 1-dB bandwidth of 31 nm. The α-Si/SiN grating architecture presented in this work enables the development of compact and efficient optical interfaces for SiN integrated photonics circuits with applications including optical communications, sensing, and quantum photonics.

High-power and narrow-linewidth nanosecond pulsed intracavity crystalline Raman laser operating at 1.7 µm

We report on a high-power and narrow-linewidth nanosecond pulsed intracavity crystalline Raman laser at 1.7 µm. Driven by an acousto-optically Q-switched 1314 nm two-crystal Nd:YLF laser, the highly efficient cascaded YVO4 Raman laser at 1715nm was obtained within the well-designed L-shaped resonator. Thanks to the absence of spatial hole burning in the stimulated Raman scattering process, significant spectral purification of second-Stokes radiation was observed by incorporating a fused silica etalon in the high-Q fundamental cavity. Under the repetition rate of 4 kHz, the highest average output power for single longitudinal mode operation was up to 2.2 W with the aid of precision vibration isolation and precision temperature controlling, corresponding to the pulse duration of ∼2.8 ns and the spectral linewidth of ∼330 MHz. Further increasing the launched pump power, the second-Stokes laser tended toward be always multimode, and the maximum average output power amounted to 4.8 W with the peak power of ∼0.8 MW and the spectral linewidth of ∼0.08 nm. The second-Stokes emission was near diffraction limited with M2 < 1.4 across the whole pump power range.

Humidity Sensing Using a Multimode Fiber Ring Laser with Thermal Compensation

We propose a multimode fiber laser sensor utilizing PI-SMF (polyimide-coated single mode fiber) for low-error relative humidity (RH) measurement, which is temperature compensated based on FBG. The PI-SMF in the laser cavity is used as a sensing element, and its length varies with humidity and temperature by volume-variation induced strain, which leads to frequency shift of the longitudinal mode beat frequency signal (BFS). When the 2000 MHz BFS is selected as the sensing signal, a RH sensitivity of −2.68 kHz/%RH and a temperature sensitivity of −14.05 kHz/°C are achieved. The peak shift of the FBG-based laser emission spectrum is only sensitive to temperature rather than RH with a temperature sensitivity of 9.95 pm/°C, which is used as the temperature compensation for RH measurements. By monitoring the response of the BFS and the laser wavelength, the cross-sensitivity effect of RH and temperature is overcome, and low-error RH measurement in the temperature range of 20 to 65 °C is realized with errors within ±0.67 %RH (25 to 85 %RH). The scheme does not require the design and production of complex structures and hygroscopic material coating processes, owning the advantages of simple structure, easy operation and high accuracy, and is expected to be practically applied in food safety and environmental monitoring.

Mining Multimodal Travel Mobilities with Big Ridership Data: Comparative Analysis of Subways and Taxis

Understanding traveler mobility in cities is significant for urban planning and traffic management. However, most traditional studies have focused on travel mobility in a single traffic mode. Only limited studies have focused on the travel mobility associated with multimodal transportation. Subways are considered a green travel mode with large capacity, while taxis are an energy-consuming travel mode that provides a personalized service. Exploring the relationship between subway mobility and taxi mobility is conducive to building a sustainable multimodal transportation system, such as one with mobility as a service (MaaS). In this study, we propose a framework for comparatively analyzing the travel mobilities associated with subways and taxis. Firstly, we divided taxi trips into three groups: competitive, cooperative, and complementary. Voronoi diagrams based on subway stations were introduced to divide regions. An entropy index was adopted to measure the mix of taxi trips. Secondly, subway and taxi trip networks were constructed based on the divided regions. The framework was tested based on the automatic fare collection (AFC) data and global positioning system (GPS) data of a subway in Beijing, China. The results showed that the proportions of taxi competition, taxi cooperation, and taxi complements were 9.1%, 35.6%, and 55.3%, respectively. The entropy was large in the central city and small in the suburbs. Moreover, it was found that the subway trip network was connected more closely than the taxi network. However, the unbalanced condition of taxis is more serious than that of the subway.

Personalized driving behavior oriented autonomous vehicle control for typical traffic situations

autonomous driving systems not only provide services for human drivers, but also need to consider the personalized driving requirements of human beings. In current road traffic environments, the driving behaviors of drivers differ significantly. This suggests that the various needs of different drivers cannot be met by a single behavior mode in an autonomous driving decision-making system. This paper looks at the personalized characteristics of various drivers and considers the implications of their differences. First, a Proportional Integral Differential (PID) feedback channel is introduced in a traditional Model Predictive Control (MPC) to improve the performance of the controller, and comprehensively considering the collision risk, motion hysteresis and rule constraints, referring to the MPC idea, a collision avoidance method based on Q-ABSAS optimization is proposed. Then based on the Chance Constrained Programming, the control constraint is combined with driver personalization to reflect a variety of driving personality characteristics. Finally, the proposed method is tested using Hardware-in-the-loop (HIL) experiments. The experiment results demonstrate that the proposed method can successfully implement vehicle tracking control and make the vehicle's state of movement match the driver's expectations, which can increase driver comfort and driving safety.

How – and How Much? An Analysis of Major Conflict Lines Regarding the Transformation of German Animal Farming

Based on the concept of a 'future workshop', this paper contributes to the understanding of major conflict lines and future pathways for animal farming in Germany. Participants in the future workshop were tasked with outlining their ideal vision of the future of animal farming, focusing on both its mode and quantity. We found three different types of visions differing in their motivation, farming methods, and the scale of envisioned animal farming: ‘Higher Standards’ (V1), ‘System Change and Reduction’ (V2), ‘Alternatives to Animal Farming’ (V3). V1 seeks to secure the quantities of supply and demand of animal products in Germany with minor adjustments towards improved animal welfare and investments in resource-efficiency and climate friendliness. V2 advocates for comprehensive social and environmental systemic changes throughout the agri-food sector, with substantially fewer animals involved. V3 aims to replace animal farming, with plant-based and other alternatives, whenever and wherever possible. Our findings suggest that there is little ground for a societal consensus on a single future mode and scale of animal farming. Stakeholder dialogues and policy initiatives should therefore allow for different pathways while focusing on compromises in the near future. Short-term solutions may be acceptable to supporters of all three visions, however, achieving this requires reframing the debate from ‘securing the future of animal farming’ to ‘guiding the future of animal farming’, acknowledging the potential – albeit partly – replacement of animal farming by suitable alternatives.

Investigating changes in the electric field profiles of transverse modes in fibres due to bending

AbstractA model is presented for calculating the electric field profiles of transverse modes in fibres. Using this model, the electric field propagation of transverse modes was calculated and compared in both bent and straight Yb and Ho fibres. Our simulations revealed that the field intensities of the modes did not consistently increase or decrease by bending as expected, but rather fluctuated as the bending radii of the fibres changed from 1 to 100 cm. Additionally, it was observed that at certain bending radii, the modes of the fibres became deformed and transitioned into higher modes. Furthermore, the extent to which the modes stretched towards cladding due to bending was calculated. To provide a more comprehensive analysis of the results and investigate the effects of the physical parameters of the fibres on the bent fibre modes, simulation results were presented for two different V numbers and core radii.

Harmonic motion modes in parabolic GRIN fibers

Harmonic motion modes in parabolic GRIN fibers

Direct investigations of interactions between nucleolins and aptamers on pancreatic cancer and normal cells by atomic force microscopy

Nucleolin is overexpressed on the surface of pancreatic cancer cells and are regarded as the remarkable therapeutic target. Aptamers are capable of binding the external domain of nucleolin on the cell surface with high affinity and specificity. But nucleolin has not been localized on pancreatic cancer cells at very high spatial resolution, and the interactions between nucleolin and aptamers have not been investigated at very high force resolution level. In this work, nucleolin was localized on pancreatic cancer and normal cells by aptamers (9FU-AS1411-NH2, AS1411-NH2 and CRONH2) in Single Molecule Recognition Imaging mode of Atomic Force Microscopy. There are plenty of nucleolin on the surfaces of pancreatic cancer cells (area percentage about 5 %), while there are little nucleolin on the surfaces of normal cells. The interactions between three types of aptamers and nucleolins on the surfaces of pancreatic cancer cells were investigated by Single Molecule Force Spectroscopy. The unbinding forces of nucleolins-(9FU-AS1411-NH2) are larger than nucleolins-(AS1411-NH2). The dissociation activation energy on nucleolin-(9FU-AS1411-NH2) is higher than nucleolin-(AS1411-NH2), which indicates that the former complex is more stable and harder to dissociate than the later complex. There are no unbinding forces between nucleolin and CRONH2. All these demonstrate that nucleolin was localized on pancreatic cancer and normal cells at single molecule level quantitatively, and the interactions (unbinding forces and kinetics) between nucleolin and aptamers were studied at picoNewton level. The approaches and results of this work will pave new ways in the investigations of nucleolin and aptamers, and will also be useful in the studies on other proteins and their corresponding aptamers.

Numerical investigation on dynamic characteristics of oil-water annular flow-induced vibration in curved pipes

To improve the stability of water-lubricated transportation and reliability of pipes in service, the fluid–structure interaction numerical model has been established to investigate the dynamic characteristics of oil-water annular flow-induced vibration in curved pipes and the effect of main parameters in this study. The results illustrate that a single vibration mode of curved pipes is excited by oil-water annular flow, and there exists no multi-modality due to the limited pulsation of pressure and interface of two-phase flow. The change of velocities and oil-water ratios leads to change of flow pattern, making the dynamic response severer. When the oil-water ratio is larger than 2.035, its effect is greater than velocity. The physical properties of oil have a significant effect on the dynamic response. The root-mean-square dimensionless displacement AY,RMS/D and maximum dimensionless displacement AY,MAX/D of fuel oil-water annular flow-induced vibration decrease to 75.6% and 76.5% respectively, which means that the increase of dynamic viscosity reduces the fluid force and suppresses the vibration. AY,RMS/D and AY,MAX/D increases by 1.62 times when the bending angle θ increases from 30° to 90°, indicating that the increase of bending angles also leads to the severer dynamic response.

Q-switched temperature fiber sensing device based on graded index and D-shaped multimode fiber

In the paper, a Q-switched temperature sensing device is proposed and verified, which consists of a modulator based on a large core multimode fiber and a graded index multimode optical fiber (LMF-GIMF), and a sensing unit formed by sandwiching a D-shaped multimode fiber (MMF) between two single mode fibers (SMF). Utilizing the modulator to transform continuous light into pulsed laser, a stable Er3+-doped Q-switched laser with a repetition frequency of 23.04 kHz and a modulation depth of 7.47 % has been achieved. Under its pumping, the SMF-MMF-SMF sensing structure performed thermal detection with a sensitivity of −81.5 pm/℃ as temperature varies in the range of 25 °C to 65 °C. The temperature sensing device based on Q-switching can be used as an independent pulse laser to realize the switch between the light source and the sensing device. At the same time, the sensing device can provide real-time feedback according to the change of the central wavelength, which allows for immediate adjustments in the operational state, enhancing the flexibility and responsiveness. In addition, the characteristics of the sensor based on Q-switched laser can reduce thermal damage and extends the service life of the sensor. As far as we know, this is the first report on Q-switched temperature sensing based on the LMF-GIMF modulator. The proposed sensing device has the advantages of high signal-to-noise ratio, low operating threshold, minimal thermal damage, and serves as an independent Q-switched laser source, which can be applied to pulse laser measurement with high precision and time resolution in the future.

Energizing geriatric healthcare: A triboelectric energy harvester with self-powered morse code generator and IoT-Enabled remote sensing tactile patch

Self-powered tactile sensors unleash a diverse array of distinctive interaction techniques and other possibilities in the contemporary world of small-scale electronics. In many circumstances of information exchange, the touch sensor is a fundamental and crucial human-machine interface (HMI). Rapid advancements in portable, wearable, and Internet of Things technologies demand a tactile sensing system to be thin, flexible, effective, self-powered, and secure. Triboelectric nanogenerator (TENG) based touch sensors are the future of flexible and self-powered sensors. Triboelectric nanogenerator based sensors exhibit excellent material compatibility and can produce substantial electrical signals even when frequencies are low and forces are moderate; this motivates researchers to develop self-powered triboelectric sensors. Here, we have proposed a skin-conforming and flexible tactile sensor with a micro-patterned dielectric surface, driven by a stencil-printed activated carbon electrode (Printed carbon PC-TENG). The device performance has been enhanced through the optimization of its output, achieved by analysing its structure using Finite Element Analysis in conjunction with the electrostatic module of COMSOL Multiphysics. The fabricated device produces a voltage in an open circuit measuring 242V along with a power density of 14.69 μW/cm2 in single electrode mode. Further, it can be employed as an energy harvester, demonstrated through energizing LEDs, LCD, Wristwatches, and digital ring counter. The proposed TENG can also serve as an international Morse code generator and self-powered sensor for IoT-enabled remote-sensing finger patches, providing medical assistance to geriatric and bedridden patients.