Significant Increase In Microhardness Research Articles

Effect of Laser Shock Peening on Residual Stress, Microstructure and Hot Corrosion Behavior of Damage-Tolerant TC21 Titanium Alloy

The effect of laser shock peening (LSP) on the residual stress, microstructure and hot corrosion behavior of damage-tolerant TC21 alloy was investigated. The equilateral scanning pattern was adopted to obtain a large overlapping area for LSP. The hot corrosion experiments in a salt mixture composed of 75 wt.% Na2SO4 + 25 wt.% NaCl at 700 and 800 °C for a total exposure of 25 h were conducted. The results demonstrated that LSP caused a high compressive residual stress with a significant increase in micro-hardness and microstructural changes in the form of crystal defects, i.e., high density dislocations. The crystal defects promoted the outward diffusion of Al, Cr and Ti to form protective mixed oxides (Al, Cr, Ti)O2. These oxides improved the adhesion of outer oxide layer and hindered the inward diffusion of O, S and Cl, which was beneficial to improve hot corrosion resistance. The mass gains of LSP-treated specimens after hot corrosion at 700 and 800 °C were, respectively, 3.72 and 4.78 mg/cm2, which were much lower than those of untreated specimens (5.65 and 6.81 mg/cm2). Therefore, LSP leads to an improvement in resistance to hot corrosion of TC21 alloy.

Effect of betel leaf extract gel on the hardness of enamel

The main component of betel leaf (Piper betle Linn.) is tannin, which easily binds with proteins and can affect enamel hardness. Betel leaf extract was applied as a topical gel to the enamel of 18 bovine teeth specimens embedded in acrylic resin (three groups of 15%, 25%, and 35% gel applied for 1, 3, and 6 months). Enamel hardness was measured with a Knoop microindentation tester. Statistical analysis was done by repeated and one-way analysis of variance tests. A significant increase in microhardness was noted after 6 months of 15% betel leaf extract application (P < 0.05). Betel leaf extract gel can significantly affect enamel hardness.

Effect of thermal cycles on the laser beam welded joint of AA2060 alloys

Abstract

Microstructure and corrosion performance of 316L stainless steel fabricated by Selective Laser Melting and processed through high-pressure torsion

For the first time, the novel combination of severe plastic deformation (SPD) and Additive Manufacturing (AM) in a single process sequence was explored. 316L stainless steel (316L SS) alloy was firstly fabricated by Selective Laser Melting (SLM) AM process and subsequently processed by high-pressure torsion (HPT) SPD technique under a constant pressure of 6 GPa for different torsional revolutions. All the processed samples were subjected to electrochemical testing in a 3.5 wt % NaCl aqueous solution using open-circuit potential, potentiodynamic polarisation, and electrochemical impedance spectroscopy techniques, and characterised with scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The microscopic measurement results revealed that the melt pools and cellular structures obtained via SLM become increasingly refined through increased HPT revolutions, accompanied by significant porosity reduction and significant increase in microhardness. TEM observations revealed a homogeneously distributed nano-scale grains after 10 turns. Moreover, the results demonstrated that HPT processing significantly enhances corrosion performance of the 316L SS alloy in NaCl solution, due to the cellular structure refinement, homogeneous microstructure distribution, and the substantial removal of pores and defects. SEM and energy dispersive x-ray spectroscopy (EDX) analysis were also carried out on the corroded samples to determine the influence of cellular structure refinement on the corrosion characteristics of the 316L SS alloy.

Remineralization potential of nano-hydroxyapatite on enamel and cementum surrounding margin of computer-aided design and computer-aided manufacturing ceramic restoration.

ObjectiveThis study investigates the effects of nano-hydroxyapatite (NHA) gel and Clinpro (CP) on remineralization potential of enamel and cementum at the cavosurface area of computer-aided design and computer-aided manufacturing ceramic restoration.Materials and methodsThirty extracted human mandibular third molars were sectioned at 1 mm above and below the cemento–enamel junction to remove the cemento–enamel junction portions and replaced them with zirconia ceramic disks by bonding them to the crown and root portions with resin cement. The enamel and cementum with an area of 4×4 mm2 surrounding the ceramic disk was demineralized with carbopol. The demineralized surfaces were treated with either NHA or CP, while 1 group was left with no treatment. Vickers microhardness of enamel and cementum were determined before demineralization, after demineralization, and after remineralization. Analysis of variance and Tukey multiple comparisons were used to determine statistically significant differences at 95% level of confidence. Scanning electron microscopy and X-ray diffraction were used to evaluate for surface alterations.ResultsThe mean ± SD of Vickers microhardness for before demineralization, after demineralization, and after remineralization for enamel and cementum were 377.37±22.99, 161.95±10.54, 161.70±5.92 and 60.37±3.81, 17.65±0.91, 17.04±1.00 for the no treatment group; 378.20±18.76, 160.72±8.38, 200.08±8.29 and 62.58±3.37, 18.38±1.33, 27.99±2.68 for the NHA groups; and 380.53±25.14, 161.94±5.66, 193.16±7.54 and 62.78±4.75, 19.07±1.30, 24.46±2.02 for the CP groups. Analysis of variance indicated significant increase in microhardness of demineralized enamel and cementum upon the application of either NHA or CP (p<0.05). Post hoc multiple comparisons indicated significantly higher remineralization capability of NHA for both enamel and cementum than CP (p<0.05), as evidenced by scanning electron microscopy, indicating NHA particle deposition in the area of remineralization, and crystallinity accumulation, as indicated by X-ray diffraction.ConclusionNHA gel and CP were capable of remineralization of the enamel and cementum. NHA was more capable in the remineralization process than CP. NHA was extremely capable in the remineralization process for enamel and cementum surrounding the margin of the computer-aided design and computer-aided manufacturing ceramic.

Microstructure and properties of Cu-Cr powder metallurgical alloy induced by high-current pulsed electron beam

The purpose of paper is to investigate the microstructure and properties of Cu-Cr alloys induced by high-current pulsed electron beam (HCPEB) irradiation. Microstructure of the alloying layer was studied by means of X-ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscopy (TEM). The microhardness and friction property were also tested. The microstructure reveals that craters were formed which were fused and eliminated to form flat surface with increase of the pulse number. Additionally, the inter-diffusion of Cu and Cr elements caused component homogenization of the surface melted layer. Besides, the fine grains/particles and Cu (Cr) solid solution were formed. Those factors accounted for a significant increase in microhardness. The lowest COF and wear rate were attributed to the ultrafine Cr particles in the hard Cu matrix.

Influence of the Extended Use of Desensitizing Toothpastes on Dentin Bonding, Microhardness and Roughness.

The aim of this study was to evaluate the influence of an extended use of desensitizing toothpastes (DTs) on dentin bonding, microhardness and roughness. One hundred and twenty bovine incisor teeth were randomly divided into four groups: G1, distilled water (WATER); G2, Colgate Total 12 (CT12); G3, Colgate Sensitive Pro-Relief (CSPR); and G4, Sensodyne Repair ?αμπ; Protect (SRP). Dentin surfaces were etched with 17% EDTA and 2 years of simulated tooth brushing (20,000 cycles) was performed on their surfaces. Knoop microhardness, surface roughness and scanning electron microscopy (SEM) were performed before and after the simulated tooth brushing. For microshear bonding test, a 2-step self-etching adhesive system (Clearfil SE Bond) was used and 0.8 mm diameter composite resin (Filtek Z350 XT) cylinders were built. Microshear test was performed with an orthodontic wire and with a crosshead speed of 0.5 mm/min. The data were analyzed for: 1) bond strength (one-way ANOVA), 2) microhardness intra-group (Student's test) and inter-group (one-way ANOVA/Tukey's test) comparisons, 3) roughness intra-group (Student's test/Wilcoxon's test) and inter-group (Kruskal-Wallis/Student-Newman-Keuls test) comparisons. The extended use of both dentifrices (conventional and for sensitive teeth) did not affect the bond strength and produced a significant increase in microhardness and roughness of the dentin, except for the microhardness of the SRP group. The simulated tooth brushing technique with water produced an increase in roughness, without reducing significantly the dentin microhardness.

Effect of Resin Infiltration on Artificial Caries: An in vitro Evaluation of Resin Penetration and Microhardness.

Aim To evaluate the effectiveness of resin infiltration on artificial caries lesion by assessing the depth of resin penetration and the change in microhardness of lesion postinfiltration.Materials and methods Totally 45 human extracted premolars were used to create an artificial demineralized lesion in enamel using demineralizing solution. A total of 15 samples (group I) were infiltrated with resin. The depth of resin penetration was studied using scanning electron microscope (SEM). Other half (n = 30) of samples was equally divided into three subgroups and Vickers hardness number (VHN) values were obtained to measure the surface microhardness as group 11 a—before demineralization, 11 b—after demineralization, IIc—postresin infiltration.Results Mean depth of penetration in group I was 516.8 urn. There was statistically significant increase in VHN values of demineralized lesion postresin infiltration (independent Student’s t-test, p < 0.001).Conclusion Penetration depth of the resin infiltrant was deep enough to render beneficial effects, while significant increase in microhardness was observed postresin infiltration.Clinical significance Infiltrant used can be considered as a valid treatment option for noncavitated lesions.How to cite this article Prajapati D, Nayak R, Pai D, Upadhya N, Bhaskar VK, Kamath P. Effect of Resin Infiltration on Artificial Caries: An in vitro Evaluation of Resin Penetration and Microhardness. Int J Clin Pediatr Dent 2017;10(3):250-256.

Strength and fatigue of an ultrafine-grained Al-Cu-Mg alloy

The dependence of strength and fatigue on microstructure of the Al-Cu-Mg alloy has been investigated. Various microstructures of the alloy were produced: the one with a coarse-grained (CG) structure after T6 heat treatment; the one with a homogeneous ultrafine-grained (UFG) structure and the one with a bimodal (mixed) structure, both processed by equal-channel angular pressing (ECAP). The mean grain size and morphology of precipitates were studied by transmission electron microscopy. The ultimate tensile strength and the fatigue endurance limit were determined using the tensile and fatigue tests of standard specimens. It is established that the formation of a homogeneous UFG structure and of a bimodal (mixed) structure alloy contributes to a significant increase in microhardness by 16% and 60%, and an increase of the ultimate tensile strength by 20 and 52%, respectively, as compared to the samples subjected to T6 heat treatment. Fatigue tests show that the alloy with a bimodal (mixed) structure has the highest fatigue endurance limit, 45% higher than in the sample subjected to T6 heat treatment. In contrast, the formation of a homogeneous UFG structure enables increasing the fatigue endurance limit by 15% only.

Effect of P codeposition on the structure and microhardness of Co–W coatings electrodeposited from gluconate bath

Effects of addition of P to Co–W coatings from gluconate bath using direct current (DC) and pulse current (PC) methods have been investigated in this study. Co–W–P coatings with different P concentrations are prepared by varying hypophosphite concentration in the bath. Current efficiency of the Co–W–P electrodeposition is lower than that for Co–W coatings. Increase in NaH2PO2 concentration increases the cobalt content significantly and decreases the tungsten content drastically. Co–W–P coatings display ‘cauliflower‐like’ morphology and roughness of the coatings increases with increasing P content. As‐deposited Co–W–P deposits are amorphous while heat treatment at different temperatures has rendered them crystalline with the precipitation of stable species like, Co3W, Co2P, etc. Unlike Co–W coatings, Co–W–P shows two‐step crystallization in differential scanning calorimetry (DSC) and on heat treatment, which is similar to the behavior of Co–P electrodeposited from gluconate baths. Moreover, inclusion of phosphorous and heat treatment have led to significant increase in microhardness of the Co–W–P coatings. X‐ray photoelectron spectroscopy (XPS) studies provide a detailed insight into the nature of Co, W and P species in as‐deposited and sputtered coatings. Microhardness of the heat‐treated coatings is higher than the as‐deposited counterparts and is comparable with that of hard chromium. Copyright © 2016 John Wiley &amp; Sons, Ltd.

Peculiarities of forming diffusion bimetallic joints of aluminum foam with a monolithic magnesium alloy

Abstract The work is carried out to determine an optimal method to obtain the welded bimetallic joints of monolithic Mg-alloy with porous Al-alloy using gallium as chemical activator and heating up to 300 °C by two different methods: long-term in vacuum oven and short-term without vacuum by passing of low voltage current. There is no microstructure change in Al-foam but indentation test records the negligible reduction of the mechanical properties. SEM showed the crystallization of two types of Mg 5 Ga 2 and Mg 2 Ga inter-metallic phases in the wavy uneven diffusion zone on Mg-alloy side with significant increase of micro-hardness and Young's modulus. The narrow depth of the diffusion zone takes place in joints by short-term heating, so this method is more applicable for welding of monolithic and porous alloys at chemical activation using gallium.

Effects of postpolymerization microwave irradiation on provisional dental acrylics: physical and mechanical properties.

This study aimed to evaluate the effects of microwave irradiation on the physical and mechanical properties of poly(methyl methacrylate) (PMMA) provisional resins. Twenty bars and 20 disc-shaped specimens were fabricated for each selected provisional restorative material (Dencor and Duralay). Test groups were subjected to microwave irradiation (3 minutes at 600 W) after polymerization. Bar specimens were subjected to a flexural strength test. Disc-shaped specimens were used to evaluate microhardness. Backscattered Raman spectroscopy was employed for each group to define the degree of conversion of the monomer/polymer. The frequency bands corresponding to C = C and C = O groups were used to determine the conversion of methyl methacrylate (MMA) monomers into polymers. Glass transition temperature was determined using a differential scanning calorimeter. Microwave irradiation of both tested autopolymerizing PMMA provisional materials resulted in a statistically significant increase in microhardness, degree of conversion and glass transition temperature values. Also, the results demonstrated a significant increase in flexural strength after postpolymerization microwave irradiation for the Dencor specimens. It is concluded that mechanical and physical properties are positively influenced by microwave irradiation.

A comparative evaluation of remineralizing ability of bioactive glass and amorphous calcium phosphate casein phosphopeptide on early enamel lesion.

This study was done to evaluate remineralizing potential of bioactive glasses (BAGs) and amorphous calcium phosphate-casein phosphopeptide (ACP-CPP) on early enamel lesion. Twenty freshly extracted mandibular premolars were sectioned sagittally. The buccal half was impregnated in acrylic resin blocks and treated with 37% phosphoric acid in liquid form, to demineralize enamel surface to simulate early enamel lesion. The samples were divided into two groups. The samples in Group I were treated with ACP-CPP (GC Tooth Mousse) and in Group II with BAG (Sensodyne Repair and Protect) and stored in saliva to prevent dehydration. The samples were tested for microhardness. The data obtained was analyzed using ANOVA post hoc multiple comparison and independent sample t- test and presented as a mean and standard deviation. All the samples showed a decrease in the microhardness after demineralization. After application of remineralizing agents, Group II showed a highly significant increase in the microhardness (P < 0.05) after 10 days, while Group I showed a significant increase in microhardness after 15 days (P < 0.05). Both the remineralizing agents tested in this study can be considered effective in repair and prevention of demineralization. BAG showed better results initially, but eventually both have similar remineralizing potential.

Investigation on femto-second laser irradiation assisted shock peening of medium carbon (0.4% C) steel

In the present study, the effect of femtosecond laser irradiation on the peening behavior of 0.4% C steel has been evaluated. Laser irradiation has been conducted with a 100μJ and 300fs laser with multiple pulses under varied energy. Followed by laser irradiation, a detailed characterization of the processed zone was undertaken by scanning electron microscopy, and X-ray diffraction technique. Finally, the residual stress distribution, microhardness and wear resistance properties of the processed zone were also evaluated. Laser processing leads to shock peening associated with plasma formation and its expansion, formation of martensite and ferrito–pearlitic phase in the microstructure. Due to laser processing, there is introduction of residual stress on the surface which varies from high tensile (140MPa) to compressive (−335MPa) as compared to 152MPa of the substrate. There is a significant increase in microhardness to 350–500VHN as compared to 250VHN of substrate. The fretting wear behavior against hardened steel ball shows a significant reduction in wear depth due to laser processing. Finally, a conclusion of the mechanism of wear has been established.

Glass‐Forming Ability and Crystallization Behavior of Al86Ni9La5 Metallic Glass with Si Addition

The glass‐forming ability (GFA) of (Al86Ni9La5)100−xSix alloys, where x = 0.0, 0.2, 0.5, 1.0 and 2.0, were determined with the crystallization behavior of these alloys. As the Si content increases, the GFA reaches a maximum at x = 0.2 and then continuously decreases. The thermal stability of the metallic glass is also deteriorated owing to the Si addition, which is accompanied by a gradual disappearance of the glass transition in the DSC traces. It is demonstrated that the peak in GFA at x = 0.2 is due to the increase in atomic packing efficiency while the deterioration of GFA at larger x is related to the chemical action between Si and other elements, which leads to a heterogeneous amorphous structure and a significant increase in microhardness at x = 0.5.

In situ (α-Al2O3+ZrB2)/Al composites with network distribution fabricated by reaction hot pressing

In situ (α-Al2O3+ZrB2)/Al composites with network distribution were fabricated using low-energy ball milling and reaction hot pressing. Differential thermal analysis (DTA) was used to study the reaction mechanisms in the Al–ZrO2–B system. X-ray diffraction (XRD) and scanning electron microscopy (SEM) in conjunction with energy-dispersive X-ray spectroscopy (EDX) were used to investigate the composite phases, morphology, and microstructure of the composites. The effect of matrix network size on the microstructure and mechanical properties was investigated. The results show that the optimum sintering parameters to complete reactions in the Al–ZrO2–B system are 850°C and 60 min. In situ-synthesized α-Al2O3 and ZrB2 particles are dispersed uniformly around Al particles, forming a network microstructure; the diameters of the α-Al2O3 and ZrB2 particles are approximately 1–3 μm. When the size of Al powder increases from 60–110 μm to 150–300 μm, the overall surface contact between Al powders and reactants decreases, thereby increasing the local volume fraction of reinforcements from 12% to 21%. This increase of the local volume leads to a significant increase in microhardness of the in situ (α-Al2O3–ZrB2)/Al composites from Hv 163 to Hv 251.

CHARACTERIZATION AND MICROHARDNESS OF ELECTRODEPOSITED Ni–W COATINGS OBTAINED FROM GLUCONATE BATH

Ni – W alloy coatings are electrodeposited with direct and pulse current using gluconate bath at pH5. Effects of direct current (DC) and pulse current (PC) on structural characteristics of the coatings have been investigated by energy dispersive X-ray spectroscopy (EDXS), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), differential scanning calorimetry (DSC) and X-ray photoelectron spectroscopy (XPS). EDXS shows that W contents are 13.3 and 12.6 at.% in DC and PC (10:40) Ni – W coatings, respectively. FESEM analysis exhibits the homogeneous coarse nodular morphology in DC plated deposits. DSC studies reveal that Ni – W coatings are thermally stable up to 400°C. XPS studies demonstrate that DC plated coating has significant amount of Ni and W in elemental form along with their respective oxidized species. In contrast, mainly oxidized metals are present in the as-deposited coatings prepared with PC plating. The microhardness of pulse current (100:400) deposited Ni – W coating is about 750 HK that is much higher than DC plated coating (635 HK). Heat treatment of the deposits carried out at different temperatures show a significant increase in microhardness which can be comparable with hard chromium coatings.

Effects of Treatment with Various Remineralizing Agents on the Microhardness of Demineralized Enamel Surface.

Background and aims. Remineralization of incipient caries is one of the goals in dental health care. The present study aimed at comparing the effects of casein phosphopeptide-amorphous calcium phosphate complex (CPP-ACP), Remin Pro®, and 5% sodium fluoride varnish on remineralization of enamel lesions.Materials and methods. In this in vitro study, 60 enamel samples were randomly allocated to six groups of 10. After four days of immersion in demineralizing solution, microhardness of all samples was measured. Afterward, groups 1-3 underwent one-time treatment with fluoride varnish, CPP-ACP, and Remin Pro®, respectively. Microhardness of groups 4-6 was measured not only after one-month treatment with the above-mentioned materials (for eight hours a day), but also after re-exposing to the demineralizing solution. The results were analyzed by one-way analysis of variance (ANOVA), repeated measures ANOVA, and Fisher’s least significant difference (LSD) test.Results. None of the regimens could increase microhardness in groups 1-3. However, one-month treatment regimens in groups 4-6 caused a significant increase in microhardness. The greatest microhardness was detected in the group treated with CPP-ACP (P = 0.001). In addition, although microhardness reduced following re-demineralization in all three groups, the mean reduction was minimum in the CPP-ACP-treated group (P < 0.001).Conclusion. While long-term repeated application of all compounds improved microhardness, the remineralization potential of CPP-ACP was significantly higher than that of Remin Pro® and sodium fluoride varnish.

Evaluation of remineralization capacity of casein phosphopeptide-amorphous calcium phosphate on the carbamide peroxide treated enamel.

Objective:The aim of this study was to evaluate the potential of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) in remineralizing the bleached enamel surface using micro-hardness.Materials and Methods:Thirty human enamel slabs were randomly divided into three groups (n = 10). Groups A and B were exposed to 20% carbamide peroxide and 35% carbamide peroxide gel, respectively. After the exposure to the bleaching agent, the slabs were kept in artificial saliva for 1-week. Group C (control group) were kept in artificial saliva for 1-week. Vickers micro-hardness test was performed by Leica VMHT-Mot micro-hardness tester. CPP-ACP (Gc Tooth Mousse, Melbourne, Australia) was then applied to specimens of Groups A and B for 3 min for 2 weeks. Micro-hardness values of postbleach Group A (Ar) and Group B (Br) were recorded and statistically analyzed by paired t-test and one-way analysis of variance at the significance level of α =0.05.Results:There was a significant decrease in micro-hardness of enamel in carbamide peroxide bleached groups. However, there was a significant increase in micro-hardness after the remineralization by CPP-ACP and the extent of remineralization is more for the Group B.Conclusions:That bleaching agents reduced enamel micro-hardness and the use of CPP-ACP after bleaching can significantly enhance the micro-hardness of bleached enamel.

Comparation between Laser Surface Nitriding and Nitrogen Plasma Immersion Ion Implantation (N-PIII) on Creep Behavior of Ti-6Al-4V Alloy

Titanium alloys are widely used in machine building, aircraft manufacturing, medicine, motors, chemistry, and biomedicine due to their high strength-to-weight ratio, elasticity, corrosion resistance, and biocompatibility. In particular, Ti-6Al-4V containing (α + β) structure plays a very important role in aerospace industry in the manufacturing of components such as disks and blades for aircrafts turbines and structural forgings. However, one of the major factors limiting the life of titanium alloys in service is their degradation due to gaseous environments, in particular, to environments containing oxygen at elevated temperatures during long-term use. The sensitivity of titanium alloys to high-temperature exposure is a well-known phenomenon. When titanium alloys are heated to temperatures above approximately 800oC, oxygen, hydrogen and nitrogen can penetrate into them. The penetration of these elements increases hardness and brittleness while decreasing the toughness of the alloy. Laser surface nitriding is a technique used to modify the near-surface microstructure and/or composition by melting the surface using a high-power laser beam with reactive gas as a shrouding environment, forming a nitride layer on the surface of Ti–6Al–4V to improve the alloy’s tribological and mechanical properties. The results of laser gas nitriding of Ti–6Al–4V showed a significant increase of microhardness and enhanced erosion resistance significantly compared with untreated Ti–6Al–4V, since the nitride layer acts as a diffusion barrier for inward oxygen diffusion into the alloy, reducing the contribution of oxygen dissolution in the substrate to the total mass gain. Other important technique that was developed for the beneficial modification of surface sensitive properties is Nitrogen Plasma Immersion Ion Implantation N-PIII. A sample is immersed in plasma and subjected to negative high-voltage pulses. In the electrical field, the ions are accelerated to high energies and incorporated into the sample. Enhancing of the hardness and wear process of the materials due to the N-enriched layer caused by diffusion of N in the sample at PIII process can be expected. Both techniques provide an improvement in the creep resistance. The objective of this work was evaluating the creep resistance of the Ti-6Al-4V alloy with superficial treatments of laser nitriding and Nitrogen Plasma Immersion Ion Implantation N-PIII in creep test of Ti-6Al-4V alloy. It was used Ti-6Al-4V alloy as cylindrical bars under forged and annealing of 190 oC by 6 hours condition and cooled by air. The Ti-6Al-4V alloy after the superficial treatment of laser nitriding and N-PIII was submitted to creep tests at 600 oC in the stress of 250 MPa and 319 MPa, under constant load mode. The creep parameters are determined and a comparative analysis is established with the results gotten from the alloy with both treatments. The laser nitrided has showed an improved creep behavior compared with the same alloy with N-PIII coating, with a reduction in the creep rate and increasing the creep lifetime.