Sidewall Pressure Research Articles

Effect of nozzle type on pulse-jet cleaning performance of ceramic filter tube

The dust-cleaning efficiency of the ceramic filter tube is the key factor to determine the long-term stable operation of the dust removal system, and the type of nozzle significantly influences the performance. In this study, four types of nozzles (injection hole, sudden enlargement nozzle, tubular nozzle, and induction nozzle) are used to conduct comparative experimental study on the dust-cleaning effect of the ceramic filter tube. Using the schlieren technique find that the tubular and induction nozzles can improve the deviation angle of pulse-jet airflow. The injection parameters were set as an injection pressure of 200 kPa, an injection distance of 120 mm and a pulse width of 80 ms in the experiment. Using the sidewall pressure measurement system indicates that the integrated pressure of the sudden enlargement nozzle is the largest, but the uniformity is poor. The comprehensive pressure of the sudden enlargement nozzle is increased by 64.86 %, and the non-uniformity is reduced by 28.62 % compared with those of the induction nozzle. Using the visualization filtration cycle test system implies that the degree of damage and stripping state of the dust layer are directly proportional to the sidewall pressure. Moreover, it is found that the residual pressure drop changes exponentially with the dust removal quality under different nozzle types. These conclusions can help explain the mechanism of dust stripping and provide a basis for the selection of nozzles.

New insights into the pre-ignition behavior of methane behind reflected shock waves

Pre-ignition is an undesired combustion event known to restrict kinetic modeling validation. Previous methane oxidation studies reported premature ignition as part of ignition delay time measurements in shock tubes. In this context, the effect on the pre-ignition propensity and auto-ignition behavior of stoichiometric methane mixtures at different dilution levels of hbox {N}_2, Ar, He, and hbox {CO}_2 was studied at 10 bar and 25 bar and temperatures between 1080 K and 1350 K. In addition to conventional sidewall pressure and endwall light emission measurements, a high-speed imaging setup was utilized to visualize the ignition process. Relevant physicochemical parameters to describe and predict the pre-ignition phenomenon were used. The results suggest that dilution levels up to 80% of bath gas are not successful in mitigating early ignition occurrence and its effects at moderate pressures. Replacing hbox {N}_2 by He was found to suppress early ignition at 10 bar, attributed to an enhanced dissipation of temperature inhomogeneities in the test gas section. The present findings demonstrate that hbox {CO}_2 has potential for pre-ignition heat release mitigation, while Ar was confirmed to promote premature ignition. To the best of our knowledge, we present the first detailed study on pre-ignition mitigation for methane mixtures in shock tubes, where further insights into its ignition non-idealities are given.

Experimental Study on a Generic Side-View Mirror with Slotted Cylindrical Foot

A simple model consisting of a mirror-housing and its cylindrical foot is applied to represent the automobile side-view mirror that causes unwanted aerodynamic noise and wind drag during high-speed driving. An additional slot is made on the solid foot to modify the flow around the mirror and thus reduce the side wall pressure fluctuation and aerodynamic drag. Flow fields and wall pressure fluctuations of these side-view mirror models have been investigated experimentally in a wind tunnel. The airflow rate through the slot varies with the changing of the slot area. Wall surface pressure sensors, particle image velocimetry (PIV), and six-component balance were applied to measure the acoustic and flow characteristics. The results demonstrated that, with the increase of slot airflow rate to 30%, the side wall pressure fluctuations were reduced by 5.1 dB and the drag coefficient decreased by 10.2%. The PIV measurements showed that the vortex cluster center behind the mirror was moved upward from the wall surface due to the slot airflow injection into the wake. The turbulent kinetic energy in the side-view mirror wake near the wall decreased with the increment of the airflow rate, reducing the side wall pressure fluctuations and thereby suppressing the noise generation.

A Study of the Pulse Cleaning Process for Metal Fiber Filter Bags Based on a Discrete Phase Particle Deposition Model

Emissions of airborne particulate matter are a major cause of air pollution. A numerical approach was used to establish a single-filter-bag cleaning model based on the discrete phase particle deposition distribution law to study the effect of pulse backflushing operation parameters on the cleaning performance of the specific structure of the dust collector. It was found that increasing the pulse blowing pressure (0.2 MPa to 0.6 MPa) and extending the pulse width (0.02 s to 0.1 s) resulted in an increase in the side wall pressure of the filter bag and, thus, improved its cleaning effect. The influence of the injection pressure on the side wall pressure peak of the filter bag was more obvious than that of the pulse width. However, it cannot be concluded that the greater the injection pressure and pulse width, the better the cleaning effect. Therefore, in the actual production application, the operating cost of the equipment needs to be taken into account, as well as the amount of dust on the surface of the filter bag.

Microhardness Distribution of Long Magnesium Block Processed through Powder Metallurgy

Powder metallurgy is a popular method of making raw powders into specific shaped samples. However, the pressure distribution and the microhardness difference within the sample are nonnegligible and unclear when the sample is long or exceeds a specific size. In this study, the long magnesium blocks, with a ratio of about 2.8 between the sample height and the sample side length, are successfully synthesized under three uniaxial and two biaxial conditions. Then, the sample hardness values on the outer surface and the center plane are tested to study the microhardness distribution. The modified analytical expression indicates that the normal pressure exponentially decreases along the compression direction, which is consistent with the hardness distribution trend. Because higher pressure leads to a more compact arrangement of the powders, more metal bonds are formed after sintering. During the first pressing, the sidewall pressure makes the surface hardness higher. The secondary reverse compression mainly improves the bottom and core hardness due to the re-orientation and re-location of the powders. The obtained relationship between the applied pressure and the hardness distribution is instructive in predicting and improving the sample quality.

An Efficient Ash Cleaning Method for Flat Box Cartridge Filter: Structure, Parameters and Cleaning Mechanism of Slotted Blowing

The problem of serious ash accumulation at the lower part of flat box filter cartridges is an important limitation for the improvement of ash cleaning efficiency in this kind of filter. To solve the above-mentioned problem, the type of slotted blowing hole impacting the performance of the ash removing under the same ash cleaning area was studied. In the present work, a total of four types of slotted blowing holes with different length were designed. The influence of blowing distance and blowing pressure on dust removal performance were investigated. Numerical simulation was conducted to demonstrate the mechanism of the dust removal process. An industrial coating test was also carried out to investigate and verify the actual ash cleaning performance under the optimal conditions as obtained from the above investigations. The results showed that: (1) the performance of dust cleaning produced by a three-slit blowhole was better than that by a four-slit blowhole; (2) 0.2 MPa was determined to be the optimal blowing pressure, which meets the requirement of ash cleaning; (3) 20 mm was selected as the optimal blowing distance, as this was the distance at which the surface side wall pressure at the non-positive-to-blow hole area was obviously increased, indicating that the whole performance of ash cleaning could be improved. The results obtained in this study are of great significance for improving the efficiency of dust removal in the use of flat box filters, promoting the development of dust removal technology, protection of environment, and reduction of human health damage.

Impact response of flowing-fluid filled square vessels

The concept of cavitation drag reduction is widely known in many fields. However, the existence of cavitation is not beneficial to the protection of structures. In this study, an attempt was made to improve the protection efficiency of fluid-filled vessels by adopting the reverse approach of increasing drag forces by reducing cavitation: The vessels were filled with flowing fluids to reduce the pressure and change the shape of cavitation during penetration. Ballistic tests, numerical simulations, and theoretical analyses were conducted to evaluate the impact response of flowing-water filled square vessels impacted by a spherical projectile. The impact responses of flowing-water filled square vessels were analyzed and compared with static-water filled vessels, in terms of the deformation and failure of target panels as the vessel's walls, sidewall pressure time histories, and cavitation processes. Moreover, the mechanism of increasing drag forces due to the fluid flow was elucidated. The effects of fluid flow on the cavitation and pressure distribution were determined. This study elucidated the active attenuation mechanism of fluid flow on mitigating the damage of rear panel. The results show that fluid flow can increase the drag forces, leading to a higher protection efficiency of flowing-water filled vessels than static-water filled vessels. Owing to the effect of fluid flow, sidewall pressures are evidently lower than those in static fluid cases. Fluid flow can change pressure distributions in the vicinity of cavitation, which can alter not only the cavitation shape but also the action direction of cavitation jetting. The active attenuation effect of fluid flow predominantly contributes to mitigating the pressure accumulation on the inner surface of rear panel during penetration, resulting in lower pressures and subsequently less damage to the structures. This study sheds light on the benefits of flowing-fluid filling on increasing the drag forces as well as mitigating the cavitation pressures.

Scientific Results of the Hydrate-01 Stratigraphic Test Well Program, Western Prudhoe Bay Unit, Alaska North Slope

The United States Department of Energy, the MH21-S Research Consortium of Japan, and the United States Geological Survey are collaborating to enable gas hydrate scientific drilling and extended-duration reservoir response testing on the Alaska North Slope. To feasibly execute such a test, a location is required that is accessible from existing roads and gravel pads and that can be occupied without disrupting ongoing industry operations. A review of potential locations meeting these criteria determined the likely occurrence of gas hydrate in two fine-grained marginal-marine sands of Tertiary age in the vicinity of the inactive “Kuparuk State 7-11-12” exploration pad in the western Prudhoe Bay Unit (PBU). Existing well and seismic data for that site were insufficient to preclude the potential for free gas occurrence within the deeper (and most prospective) target sand. Therefore, with support from the PBU Working Interest Owners, Alaska Department of Natural Resources, and Petrotechnical Resources Alaska, the Hydrate-01 Stratigraphic Test Well (STW) was drilled in December 2018 to confirm the suitability of the site for future gas hydrate scientific testing. The Hydrate-01 well was successfully drilled to −3290 ft (1003 m) subsea vertical depth at a bottom hole location of approximately 900 ft (∼275 m) east of the surface location. The drilling program featured acquisition of a full suite of logging while drilling data, the collection of side-wall pressure cores, and the installation of distributed temperature and distributed acoustic sensor fiber-optic cables. The log data acquired confirmed the occurrence of gas hydrate at high saturation in two target sands. Integrated evaluation of log and sidewall core data provide petrophysical and geomechanical property information that allow for potential reservoir response to depressurization to be simulated. The deeper “B1 sand” is deemed to be most favorable for reservoir response testing as a result of confirmed gas hydrate occurrence in sediments of high intrinsic permeability, location within 100 ft (30 m) of the base of gas hydrate stability, and minimal risk for direct communication with permeable water-bearing (hydrate-free) zones. The shallower “D1 sand” provides a secondary target that is differentiated by colder in situ temperatures and the interpreted direct hydraulic communication to a lower section of non-hydrate-bearing, water-saturated sand. The Hydrate-01 log data also confirm the occurrence of at least one sub-seismic fault in close proximity to the B1 sand reservoir. To better image the distribution of the gas-hydrate-bearing reservoir sections and associated faults, a three-dimensional (3D) vertical seismic profile was conducted in early 2019 using the distributed acoustic sensors installed as part of the Hydrate-01 STW completion. Detailed two-dimensional (2D) and 3D geologic models have been constructed to enable numerical simulations to inform the planning for potential future scientific tests of reservoir response to depressurization at the site.

Effect of the Dynamic Response of a Side-Wall Pressure Measurement System on Determining the Pressure Step Signal in a Shock Tube Using a Time-of-Flight Method.

Technological progress demands accurate measurements of rapidly changing pressures. This, in turn, requires the use of dynamically calibrated pressure meters. The shock tube enables the dynamic characterization by applying an almost ideal pressure step change to the pressure sensor under calibration. This paper evaluates the effect of the dynamic response of a side-wall pressure measurement system on the detection of shock wave passage times over the side-wall pressure sensors installed along the shock tube. Furthermore, it evaluates this effect on the reference pressure step signal determined at the end-wall of the driven section using a time-of-flight method. To determine the errors in the detection of the shock front passage times over the centers of the side-wall sensors, a physical model for simulating the dynamic response of the complete measurement chain to the passage of the shock wave was developed. Due to the fact that the use of the physical model requires information about the effective diameter of the pressure sensor, special attention was paid to determining the effective diameter of the side-wall pressure sensors installed along the shock tube. The results show that the relative systematic errors in the pressure step amplitude at the end-wall of the shock tube due to the errors in the detection of the shock front passage times over the side-wall pressure sensors are less than 0.0003%. On the other hand, the systematic errors in the phase lag of the end-wall pressure signal in the calibration frequency range appropriate for high-frequency dynamic pressure applications are up to a few tens of degrees. Since the target phase measurement uncertainty of the pressure sensors used in high-frequency dynamic pressure applications is only a few degrees, the corrections for the systematic errors in the detection of the shock front passage times over the side-wall pressure sensors with the use of the developed physical dynamic model are, therefore, necessary when performing dynamic calibrations of pressure sensors with a shock tube.

Planning and Operations of the Hydrate 01 Stratigraphic Test Well, Prudhoe Bay Unit, Alaska North Slope

The National Energy Technology Laboratory, the Japan Oil, Gas and Metals National Corporation, and the U.S. Geological Survey are leading an effort to conduct an extended gas hydrate production test in northern Alaska. The proposed production test required the drilling of an initial stratigraphic test well (STW) to confirm the geologic conditions of the proposed test site. This well was completed in January 2019 in cooperation with the Prudhoe Bay Unit Working Interest Owners. The Prudhoe Bay Unit Hydrate-01 STW was spudded on 10-December-2018. Downhole data acquisition was completed on 25-December-2018, and the rig was released on 01-January-2019. The Hydrate-01 STW was drilled in two sections, including the surface hole that was drilled to a depth of 2248 ft measured depth (MD) (685 m MD) and cased, and the production hole section that was drilled to a depth of 3558 ft MD (1084 m MD) and also cased. A thermally chilled mineral-oil-based mud was used in the main (production) hole section of the well to maintain wellbore stability and quality of the wellbore acquired data. The primary wellbore data were acquired using logging-while-drilling tools. A sidewall pressure core system was also deployed to gather grain size and other data needed for the design of the future production test wells. In addition to confirming the geologic conditions at the test site, the Hydrate-01 STW was designed to serve as a monitoring well during future field operations. Therefore, two sets of fiber-optic cables, each including a bundled distributed acoustic sensor (DAS) and a distributed temperature sensor (DTS), were clamped to the outside of the production casing and cemented in place. In March 2019, the project team acquired three-dimensional (3D) DAS vertical seismic profiling data in the Hydrate-01 STW. Temperature surveys were also acquired with the DTS as deployed in the Hydrate-01 STW during the completion of the well and nearly continuously since March-2019.

A novel method for online bulk density measurement in stamped charging machine using force sensors

ABSTRACT Stamped charging of coal has become increasingly demanded in blast furnaces, as pulverized coal injection is more used. In the stamped charging process, the bulk density of the coal is the most important parameter, which affects the productivity and campaign life of the coke oven batteries. Hence, online measurement of coal bulk density is very crucial for increased productivity. In this paper, a novel methodology that exploits the relationship between coal bulk density and sidewall pressure is discussed. The relationship has been quantitatively established by lab-scale experiments. Also, the lab-scale experiment describes a unique methodology, which enables pressure sensor mounting on the actual stamping machine for the actual application. The obtained relationship can be used directly for determining the bulk density of the actual stamped charge coal cakes in coke plants.

Characteristics and evaluation index of pulse-jet dust cleaning of filter cartridge

In this study, we investigated the influence of tubular nozzle and upper opening diffuser on the performance of pulse-jet dust cleaning of filter cartridges through experimental tests. The optimal tubular nozzle injection distance was 200 mm, the sidewall pressure increased along the height of the filter cartridge, and the pressure at the lower part of the filter cartridge was much higher than that at the upper part. However, under the upper open diffuser, the uniformity of the pressure distribution along the height of the cartridge was effectively improved. Combined with the entropy weight method and considering the peak pressure and pressure uniformity, the integrated pressure was proposed as a comprehensive index to evaluate the dust cleaning effect on filter cartridges. this result was verified using data from the literature，and can be used to evaluate the dust cleaning effect of filter cartridges.

Experimental study on the shape of plunge pool in the Horizontal Swirl Spillway Tunnel

According to the study on the shape of plunge pool in the horizontal swirl spillway tunnel, the design scheme of a plunge pool with better energy dissipation effect is proposed. Based on the hydraulic physical model test, which includes atmospheric pressure and decompression tests, and combined with the different design scheme of a plunge pool, measurement results of fluctuating pressure. Main frequency and sidewall pressure are analysed. The results show that the inlet section of the plunge pool is connected by a gradual variable section which length of gradient segment 6m. The shape of the gradient section is a long round variable gate hole. To improve the side wall pressure, the inlet section is increasing from 6.0m to 14.0m. Finally, the proposed plunge pool has the advantages of simple design and convenient construction, and these studies provide reference and support for the design of hydropower dams in western China.

Multiple physical properties of gas hydrate-bearing sediments recovered from Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well

Knowledge of the petrophysical and geomechanical properties of gas hydrate-bearing sediments is essential for predicting reservoir responses to gas production from gas hydrate reservoirs. In December 2018, Stratigraphic Test Well Hydrate-01 was drilled in the western part of the Prudhoe Bay Unit, Alaska North Slope, as part of the technical planning effort for a future long-term gas hydrate production test. Side-wall pressure coring was conducted to recover gas hydrate-bearing sediments from two reservoir sections named Unit B and Unit D. A total of 34 cores were successfully recovered during five runs of a wireline deployed pressure corer, and a total of 17 cores were preserved for advanced laboratory analysis. The samples were frozen inside the pressure core autoclave by liquid nitrogen while at high pressure before being removed and stored under liquid nitrogen at atmospheric pressure. High-resolution X-ray computed tomography showed the samples were high-quality, with undisturbed lithological layers. The Unit B and D sediments were categorized as sand or sandy silt with high hydrate saturation. Gas compositions suggest the hydrates formed with thermogenic and microbial mixed gases. Permeability tests and triaxial compression tests were conducted on the hydrate-bearing sediments. Low strengthening and high permeability at hydrate saturation Sh > 80% were observed. There was a small permeability reduction during the triaxial compression tests owing to porosity loss with increasing effective stress in the highly permeable sandy sediment after hydrate dissociation. The apparent minimal changes in porosity and permeability during the tests were due to the low-clay content and low compressibility of the quartz sand grains in the recovered cores. X-ray powder diffraction and thermal conductivity analysis also suggested a high quartz content for the analyzed samples.

Why is the measured maximum lift in wind tunnels dependent on the measurement method?

The present study investigates the differences in the predicted lift for a wind tunnel model from either surface pressures or side wall pressures. The investigated model is the NACA63-418 tested in the Poul la Cour tunnel. The measurements are compared with previous conducted wind tunnel campaigns for a Reynolds number of 3E6. The 3D CFD model of the wind tunnel will be used for investigating details of the flow mechanisms, and to validate assumptions and findings from the experimental data. The CFD simulations show that when the flow is attached the lift based on the side wall pressures results in almost the same lift as calculated from the surface pressures. Around the maximum lift and in the stalled region the flow is not anymore 2D. For the NACA63-418 airfoil the lift based on the side wall pressures are generally highest. The CFD simulations confirm that the method used to predict the lift from the limited side wall pressure strips in the wind tunnel is applicable.

Shock-induced ignition and pyrolysis of high-pressure methane and natural gas mixtures

A high-pressure shock tube was used to study ignition delay times (IDT) of CH4/O2/Ar and natural gas/O2/Ar mixtures behind reflected shock waves. Reaction progress was monitored using sidewall pressure and direct laser absorption diagnostics of CH4 near 3.175 µm and ethylene near 10.532 µm. Stoichiometric, fuel-rich and fuel-lean mixtures of CH4/O2, highly dilute in argon, were studied over a temperature range from 1450 to 1850 K and pressures between 10 and 55 atm. Of note are the experiments conducted with fuel-rich mixtures, as there is a lack of literature data in this regime. In the current study, the methane absorption diagnostic provided a unique tool enabling both speciation of methane and a clear definition of ignition delay time. In addition to methane oxidation, we have measured ignition delay times of commercial natural gas blends over a temperature range of 1408–1541 K, at pressures near 12 atm, and at an equivalence ratio of 1. To understand the effects of minor constituents (such as ethane and propane) in commercial natural gas blends, ethylene concentration during pyrolysis experiments was monitored using a two-wavelength scheme (10.532 µm and 10.674 µm) using a CO2 gas laser. The deficiency of existing kinetic models towards predicting the high-temperature kinetics of natural gas blends was highlighted through our measurements. Therefore, this study also provides data critical for refining these models. Extensive sensitivity analysis emphasizes the importance of the reaction CH3+C2H6→CH4+C2H5 during natural gas pyrolysis, and the accuracy of the chemical kinetic models is significantly improved by using a revised reaction rate constant (Shao et al. 2019) for this reaction. These measurements extend the test conditions of earlier studies of methane and commercial natural gas.

Experimental Study of Sidewall Pressure Induced by Ferroparticles in Fluid under a Pulsating Magnetic Field

For several decades, magnetic nano- and microparticles have been used in various applications, as they can be attracted and controlled using external magnetic fields. Recently, carbonyl iron microparticles were used in a feasibility study of a new cardiac pacing application. The particles were inserted into a heart, attracted to its sidewall using a pulsating magnetic field, and applied pulsating pressure on its sidewall. The magnitude of the sidewall pressure is a critical parameter for the success and safety of the application, and it was evaluated analytically using a simplified model. In the present study, the behaviour of carbonyl iron microparticles in a water chamber was studied experimentally. Several masses of these particles were attracted to the sidewall of the chamber using an external pulsating magnetic field; the behaviours of the masses of particles, the particle–particle interaction, and the influence of fluid dynamics on them were examined during different periods of pulses. The sidewall pressure during their attraction was measured using an in-house piezoelectric polyvinylidene fluoride sensor. The relations between the measured sidewall pressure and the mass of the particles, their sizes, and the magnetic field exposure time were investigated. The obtained results suggest an asymptotic sidewall pressure value for the specified magnetic field. The measurements of the sidewall pressure are compared with evaluated results from the analytical model, showing that the model over-predicts the sidewall pressure.

Numerical Simulation Study on The Degree of Submarine Cable Protection by Riprap Protection Layer Against Anchor

Based on the discrete element theory, the rockfill-anchor-cable discrete element model was built on the PFC3D simulation platform. Combined with the engineering practice, numerical simulation of the penetration process of anchor into the submarine cable riprap protection layer was carried out, the relationship between force and displacement and the sidewall pressure of the submarine cable under the anchor partial penetration were obtained, and the anti-anchor damage ability of the submarine cable was evaluated quantitatively. The results show that the resistance force of the riprap to the anchor increases gradually with the increase of anchor invasive displacement, and eventually stabilize, which reflects the forming, developing, rupturing and restructuring process of the physical chain of the ripped-rock. Furthermore, the riprap protection layer has a significant protective effect on the submarine cable.

Side-wall pressure distribution of cylindrical granular containers with flat bottom

The side-wall pressure distribution in static silos is an important and open problem related to storage safety of granular materials. Referring to Lvin's theory [Powder Technology 4, 280 (1971)] and Rodolfo's 2D numerical result [Phys. Rev. E 97.1(2018)], a new theoretical model of side-wall pressure is established by assuming the friction coefficient as well as the ratio of horizontal to vertical stress changing with depth position in granular columns. Furthermore, the transition of stress state between hydrostatic-like and Janssen-like in a cylindrical granular container with flat bottom is systematically investigated by our model and experiment, and finally an empirical expression describing this transition is proposed.

Shock tube studies of ethanol preignition

Understanding premature ignition or preignition is of great importance as this phenomenon influences the design and operation of internal combustion engines. Preignition leading to super-knock restricts the efficiency of downsized boosted engines. To gain a fundamental understanding of preignition and how it affects an otherwise homogeneous ignition process, a shock tube may be used to decipher the influence of fuel chemical structure, temperature, pressure, equivalence ratio and bath gas on preignition. In a previous work by Javed et al. (2017), ignition delay time measurements of n-heptane showed significantly expedited reactivity compared to well-validated chemical kinetic models in the intermediate-temperature regime. In the current work, ethanol is chosen as a representative fuel that, unlike n-heptane, does not exhibit negative temperature coefficient (NTC) behaviour. Reactive mixtures containing 2.9% and 5% of ethanol at equivalence ratios of 0.5 and 1 were used for the measurement of ignition delay times behind reflected shock waves at 2 and 4 bar. Effect of bath gas was studied with mixtures containing either Ar or N2. In addition to conventional side-wall pressure and OH* measurements, a high-speed imaging setup was utilized to visualize the shock tube cross-section through a transparent quartz end-wall. The results suggest that preignition events are more likely to happen in mixtures containing higher ethanol concentration and that preignition energy release is more pronounced at lower temperatures. High-speed imaging shows that low-temperature ignition process is usually initiated from an individual hot spot that grows gradually, while high-temperatures ignition starts from many spots simultaneously which consume the reactive mixture almost homogeneously.