Shear Bond Strength Values Research Articles

Improving the Mechanical Properties of Glass Ionomer Cement With Nanocrystalline Cellulose From Rice Husk.

This study aimed to evaluate the effect of incorporating nanocrystalline cellulose (NCC) sourced from rice husk on the mechanical properties of a commercial glass ionomer cement (GIC). NCC was isolated through acid hydrolysis, and its crystallinity, chemical structure, and morphology were characterized through x-ray diffractometry, Fourier-transform infrared spectroscopy, and transmission electron microscopy, respectively. Various concentrations of NCC (0%, 0.5%, 1%, and 1.5%) were added to reinforce the GIC matrix. Mechanical tests including compressive strength, flexural strength, hardness, and shear bond strength were conducted on the modified GIC samples. The addition of NCC resulted in increased hardness and shear bond strength values, with 1% NCC showing the highest values compared to other concentrations. However, there was no significant improvement observed in the compressive and flexural strength of the modified GIC. Failure mode test revealed a reduction in adhesive failure with the addition of NCC. Incorporating small amounts of NCC (0.5%-1%) suggests a promising and affordable modification of GIC restorative material using biomass residue, resulting in improved mechanical properties.

Effect of Different Liquids and Thermal Aging Procedures on the Shear Bond Strength of APC II, APC Flash-Free, and Conventional Ceramic Brackets: An In Vitro Study.

The purpose of this study was to compare the effects of cherry juice, coffee, coke, gastric acid, and the thermo-aging procedure (TAP) on the shear bond strength (SBS) of APC II, APC flash-free, and conventional ceramic brackets. A total of 180 human premolar teeth were randomly divided into three major groups according to the type of ceramic bracket. Then, six subgroups (n=10) were established from each major group: Group 1: control; Group 2: only TAP; Group 3: 72 hours of cherry juice exposure + TAP; Group 4: 72 hours of coffee exposure + TAP; Group 5: 72 hours of coke exposure + TAP; and Group 6: 24 hours gastric acid exposure + TAP. SBS was assessed for each specimen using a universal test device, and the adhesive remnant index (ARI) was scored under a light microscope. Kruskal-Wallis and post-hoc Tamhane tests were used to analyze the data. Among the control groups, the highest SBS value belonged to conventional ceramic brackets (p<0.01). SBS values for all groups decreased as a result of each liquid and TAP. Gastric acid and coke had the greatest detrimental effects on SBS, while TAP had the least negative effects. The SBS values of APC II, APC flash-free, and conventional brackets were found to be statistically insignificant after different liquid exposures and TAP. TAP and various fluids had a negative impact on the SBS value of ceramic brackets. SBS values, however, were still higher than clinically acceptable (8-9 MPa) values, even after exposure to gastric acid and coke.

Comparative analysis of shear bond strength of MTA and Theracal PT with different restorative materials

BackgroundThis study aimed to compare the in vitro shear bond strength (SBS) of mineral trioxide aggregate (MTA) and dual-cured, resin-modified calcium silicate material (Theracal PT) to composite resin, compomer, and bulk-fill composite, and to evaluate the bond failure mode under a stereomicroscope.MethodsNinety acrylic specimens, each with a 4 mm diameter and 2 mm height central hole, were prepared. These specimens were randomly divided into two groups based on the capping materials: MTA and Theracal PT. Each group was further subdivided into three subgroups (n = 15) according to the restorative materials: composite resin, compomer, and bulk-fill composite. The specimens were then subjected to shear testing using a universal testing machine at a crosshead speed of 1 mm/min. Post-test, the fracture locations were examined using a stereomicroscope. Data were analyzed using a two-way analysis of variance (ANOVA) and the Tukey test.ResultsThe SBS values for the Theracal PT group were significantly higher than those for the MTA group (p < 0.001). Within the MTA groups, no significant differences were observed in SBS values across the different restorative materials. However, a significant difference was found between the mean SBS values of the Theracal PT + composite resin group and the Theracal PT + compomer group (p < 0.001).ConclusionsTheracal PT shows promise in dentistry due to its superior bond strength. Given its bond values, Theracal PT appears capable of forming durable and long-lasting restorations by establishing reliable bonds with various restorative materials commonly used in dentistry.

Development of a graphene oxide/hydroxyapatite-containing orthodontic primer: An in-vitro study

Fixed orthodontic appliances increase the risk of enamel demineralization and the development of white spot lesions (WSLs). This study aimed to develop a novel orthodontic primer that incorporates graphene oxide (GO) and hydroxyapatite (HA), investigate their cell viability, bonding strength, and enamel damage, and evaluate their antibacterial and remineralization properties. Nine groups were prepared by adding different concentrations of GO (0.1, 0.25, and 0.5 wt%) and HA (2, 5, and 7 wt%) to Transbond™ XT orthodontic primer. After observing the surface morphology of the material by a Field Emission Scanning Electron Microscope (FESEM), the phase of the materials by X-ray diffraction (XRD), and their chemical compositions by Energy Dispersive X-ray spectroscopy (EDX). The prepared primers were compared to the control primer group in terms of cell viability, shear bond strength (SBS), adhesive remnant index (ARI), enamel damage index (EDI), and antibacterial test. Then the groups with higher antibacterial properties (GOHA 0.1–2, GOHA 0.1–5, GOHA 0.25–2) were selected to evaluate their remineralization properties. Primers with all the prepared concentrations of GO/HA revealed acceptable cell viability levels within the limit of the ISO standards with comparable SBS and ARI values with the control primer (p > 0.05). Simultaneously, the EDI significantly reduced, and the antibacterial properties enhanced when compared to the control group (p < 0.05). The result of remineralization properties revealed that the selected groups had significantly higher remineralization ability than the control group which was more pronounced in GOHA 0.25–2 group. All the prepared orthodontic primers with different concentrations of GO/HA are safe biologically with adequate SBS, ARI, and EDI values for clinical application with enhanced antibacterial properties. The GOHA 0.25–2 experimental primer reveals the best antibacterial and remineralization properties which require further in-vitro and in-vivo investigation as a preventive measure of WSL.

Influence of luting strategies on dentin bond performance of self-adhesive resin luting cement in combination with a universal adhesive.

This study aimed to evaluate the dentin bond performance of various resin luting cement (RLC) systems combined with universal adhesives in different luting strategies. Three self-adhesive resin luting cements (SRLCs) were used with universal adhesives as primers. Twelve specimens per group were prepared to measure shear bond strength (SBS) under distinct luting strategies in etch-&-rinse and self-etch modes. Regarding luting strategies, the bonded specimens were categorized into four groups based on tooth primer application and the curing mode of the SRLC paste: (i) with light irradiation of the tooth primer (wL) + dual-cure mode (DC) of the SRLC paste, (ii) wL + self-cure mode (SC) of the SRLC paste, (iii) without light irradiation of the tooth primer (woL) + DC mode of the SRLC paste, and (iv) woL + SC mode of the SRLC paste. Specimens were also subjected to different storage conditions: 24h in water (baseline condition) and 10,000 cycles of thermal cycling. Luting strategy, storage condition, and SRLC system type significantly influenced dentin SBS values in both etching modes. Notably, certain SRLCs exhibited significantly higher dentin SBS when the primer was light-irradiated compared with no primer irradiation. Most SRLCs demonstrated higher dentin bond strength with light-irradiated primers, suggesting potential enhancement of dentin bond performance via primer light irradiation.

Evaluation of the shear bond strength between CAD/CAM blocks and sonic/thermoviscous bulk-fill composites with different surface treatments

Background/purposeTo evaluate the shear bond strength (SBS) of nanoceramic hybrid CAD/CAM blocks with two bulk-fill composites in deep margin elevation following different surface pretreatments. Materials and methodsForty cylindrical-shaped samples (3 mm diameter × 4 mm height) were prepared from each group of bulk-fill resin composites (BRC) (SonicFill 3/SF, VisCalor bulk/VS), and 80 samples (14.5 mm × 7.2 mm × 2 mm) were sectioned from Grandio Block. Specimens of each BRC were assigned to two subgroups, and surfaces of one group were treated with a tribochemical silica-coating. The CAD/CAM block sample surfaces were treated with Al2O3 particles. CAD/CAM block and composite samples were luted using dual-cure universal resin-based cement (Bifix QM). Following immersion in distilled water for 24 h, the samples were divided as immediate and test groups. The test group was subjected to thermocycle (5–55 °C, 10,000 cycles). The SBS of the resin-based cement between the blocks and BRC was tested on a universal testing device until failure. Failure type was determined using a stereomicroscope. The roughening pattern was evaluated with SEM. Statistical analysis included Shapiro Wilk, Generalized Linear Models, and Fisher's Exact tests (P < 0.05). ResultsNo statistically significant difference was found between the mean SBS values according to deep margin elevation materials and surface pretreatment (P > 0.05). Aging procedure resulted in a statistically significant difference between the mean SBS values (P < 0.001). While the mean SBS value was 33.7 ± 7.9 MPa in immediate group, it was calculated as 22.6 ± 6.3 MPa in test group following thermocycle. ConclusionIn terms of SBS, both bulk-fill resin composites performed similarly. Although higher SBS values were obtained with tribochemical silica-coating, the adverse effects of thermocycling on bonding could not be prevented.

Effect of time and photoactivated face on bond strength of brackets and on degree of monomer conversion.

To evaluate the effect of four different photoactivation protocols (according to "photoactivated faces" - mesial/distal, cervical/incisal or center - and "photoactivation time" - 6-3s) of a high-power photo activator (Valo Cordless®-Ultradent) on the shear bond strength (SBS) between metal brackets and dental enamel and on the degree of conversion (DC) of an orthodontic resin. 40 bovine incisor crowns were randomly assigned to 4 groups (n = 10). The brackets were bonded with Transbond XT® resin using 4 protocols according to the "photoactivation protocol" factor (which was subdivided into photoactivated faces and photoactivation time): V3C = 3s + center; V6C = 6s + center; V3M3D = 3s on mesial + 3s on distal; V3C3I = 3s on cervical + 3s on incisal. All the samples were stored for 4 months (water,37ºC) and then subjected to a SBS test (100KgF,1mm/min). 40 resin discs were made to evaluate the monomer degree of conversion. Data from the SBS and DC were assessed by One-way ANOVA and Tukey's test (5%). Bond failures were analyzed according to the Adhesive Remnant Index (ARI) and evaluated by the Kruskal-Wallis test (5%). There was a statistically significant difference (p = 0.008) in the One-way ANOVA result for SBS values between all groups, but the protocols showed statistically similar results (p ≥ 0.05-Tukey's tests) concerning the photoactivated faces (V6C, V3M3D and V3C3I) and photoactivation time (V3C and V6C) factors individually. There was no statistically significant difference (p ≥ 0.05) in the One-way ANOVA result for DC values. The SBS and DC values will vary depending on the protocol applied. It is possible to maintain the bracket fixation quality with the use of a high-power LED photo activator associated with a shorter photoactivation time. However, it is assumed that not all types of protocols that might be applied will provide quality bonding, such as V3C, V3M3D and V3C3I, which may - depending on the SBS and DC values - affect the final treatment time, due to brackets debonding, or increase of possibility of damage to dental enamel during bracket removal. Clinical studies are suggested to confirm the hypotheses of this research.

An in vitro assessment of the influence of dentinal pretreatment with chlorhexidine, nonthermal atmospheric plasma, chitosan, and proanthocyanidins on shear bond strength to composite.

Dentin biomodification has been emphasized as a means of improving the bond between composite resin and tooth surface, consequently enhancing its longevity. To evaluate the shear bond strength (SBS) of dentin after pretreatment with 2% chlorhexidine (CHX), 2% chitosan, nonthermal atmospheric plasma (NTAP), proanthocyanidins (5% pine bark ((PB) and 5% bromelain). The study was designed as an in vitro investigation. Sixty extracted mandibular molars (n = 60) were gathered for this in vitro research. The teeth were decoronated to expose the dentinal surface. All samples have been etched with 37% phosphoric acid and then pretreated with respective dentin biomodifiers. Group I (control): No pretreatment was done, Group II: 2% CHX, Group III: NTAP, Group IV: 5% PB, Group V: 2% chitosan, Group VI: 5% bromelain. Specimens were evaluated for the SBS test, which was done under the instron universal machine at a speed of 1 mm/min after a bonding agent and composite build-up were applied. While Group I had the lowest SBS (10.391.59Mpa), Group V had the highest SBS (30.111.53 Mpa). Pretreatment of the dentin enhanced the SBS of dentin to composite. When utilized after etching, dentin biomodification increased all experimental group's bond strength in contrast to the control. The highest SBS values were recorded with 2% chitosan, followed by NTAP.

The effect of surface treatment and thermal aging on the bonding of clear aligner attachments to provisional resin-based material: shear bond strength analysis.

The aim of this study is to evaluate the effect of different surface treatments on the shear bond strength (SBS) of clear aligner attachments bonded to Bis-acryl provisional crowns. 120 cylindrical bisacrylic composite material (ProTemp type) specimens were prepared and divided into six groups (n = 20) based on surface treatment, control: (no treatment); super coarse grit diamond bur, carbide bur, alumina-blasting, non-thermal plasma treatment, and Er:YAG laser treatment. The features of treated surfaces were examined using scanning electron microscopy (SEM). A flowable composite resin (Transbond XT; 3M Unitek) was bonded to the specimens forming the attachment. Half of specimens were subjected to thermal cycling (5,000 cycles). SBS was measured before and after thermal cycling. Each specimen was loaded at the attachment/resin interface at a speed of 0.5 mm/min until failure. The nature of the failure was analyzed using the composite remnants index (CRI). Two-way ANOVA and Tukey HSD were used for data analysis α = 0.5. For CRI scores analysis, Kruskal-Wallis test and Dunn's multiple comparison were used as post-hoc test. SEM analysis showed that all surface treatments altered surface properties and increase surface bonding area. The specimens treated with plasma, Er:YAG laser, and alumina-blasting had higher SBS values before and after thermal cycling. In comparison to control plasma, Er:YAG laser, and alumina-blasting showed a significant increase in SBS (P < 0.001) while carbide and diamond bur groups showed no significant differences (P > 0.05). Thermal cycling significantly decreased the SBS of control, carbide bur, diamond bur, and Er:YAG laser while no significant effect of alumina-blasting and plasma group. Er:YAG laser and plasma groups significantly exhibited more dominance for scores 2 and score 3 and the absence of score 0. Alumina-blasting, Er:YAG laser, or non-thermal plasma surface treatments increased the shear bond strength between clear aligner attachments and resin-based restorations.

Comparison of the Effect of Adhesive Protocols and Light Curing Units on the Repair Bond Strength of Bulk Fill Composite Resins

Background: The aim of this study is to compare the shear bond strength (SBS) after the repair of a microhybrid composite resin (CR) with three different bulk fill CRs using a 2nd and 3rd generation light-emitting diode (LED) light curing units and a universal adhesive with different application protocols. Methods: 120 acrylic blocks, each with an open surface and a depth of 2 mm and a diameter of 6 mm, were filled with a microhybrid CR (Filtek Z250) and cured with an LED for 20 seconds. The samples were roughened for 5 seconds with a diamond fissure bur under water cooling and then subjected to 5,000 thermal cycles. A universal adhesive was applied to the prepared samples using two different protocols (total etch and self-etch), and samples were then filled with bulk fill CRs. Each bulk fill CR group was polymerized with 2nd and 3rd generation LED to form subgroups (n=10). The SBS values were recorded in MPa using a universal testing device. Results: The highest SBS values were obtained for the X-tra Fil group in total etch mode with polymerization using 3rd generation LED, while the lowest SBS values were found for Filtek One Bulk Fill group in self-etch mode with polymerization using the 3rd generation LED. In all groups, total etch mode yielded higher SBS values compared to self-etch mode. Conclusion: Different adhesive protocols and LCUs were found to affect the SBS values of bulk fill CRs during repair.

The effect of antimicrobial peptide-added adhesive resins on shear bond strength and the adhesive remnant index of orthodontic brackets

ObjectivesThe aim of this study was to evaluate the effect of in-vivo produced Nisin which is an antimicrobial peptide (AMP) added to adhesive resin on shear bond strength (SBS) and the adhesive remnant index (ARI) of orthodontic brackets.MethodsBacterial AMP was produced by fermentation and the ideal AMP/Bond concentration and antimicrobial efficacy of the mixture were tested. To evaluate the SBS and ARI scores of AMP-added adhesive resins, 80 maxillary premolar teeth extracted for orthodontic purposes were used and randomly assigned into 2 groups (n = 40). Group 1: Control Group (teeth bonded with standard adhesive resin); Group 2: Experimental Group (teeth bonded with AMP-added adhesive resin). Statistical analysis was performed using the SPSS package program and applying the Mann-Whitney U and Fisher’s exact tests. P < 0.05 was considered as statistically significant.ResultsNisin synthesized in-vivo from Lactococcus lactis (L. lactis) (ATCC 7962) bacteria was provided to form a homogenous solution at an ideal concentration To find the minimum AMP/Bond mixture ratio that showed maximum antimicrobial activity, AMP and Bond mixtures were tested at various concentration levels between 1/160 and 1/2 (AMP/Bond). As a result, the optimum ratio was determined as 1/40. The antimicrobial efficacy of Nisin-added adhesive resin was tested against Streptococcus mutans (S. mutans) (ATCC 35,688) and Lactobacillus strains (cariogenic microorganisms). AMP formed a 2.7 cm diameter zone alone, while 1/40 AMP-bond mixture formed a 1.2 cm diameter zone. SBS values of the teeth bonded with Nisin added adhesive (17.49 ± 5.31) were significantly higher than the control group (14.54 ± 4.96) (P = 0.004). According to the four point scale, Nisin added adhesive provided a higher ARI score in favour of the adhesive and tooth compared to the control group (ARI = 3, n = 20).ConclusionsNisin produced from L. lactis (ATCC 7962) had greater antimicrobial effects after mixing with adhesive bond against cariogenic microorganisms S. mutans (ATCC 35,688) and Lactobacillus strains. Nisin added adhesive increased shear bond strength (SBS) of orthodontic brackets and ARI scores in favor of adhesive & teeth.Clinical relevanceClinicians should take into account that using Nisin-added adhesive resin in orthodontic treatments can provide prophylaxis against tooth decay, especially in patients with poor oral hygiene.

Shear bond strength and adhesive remnant index evaluation of three different orthodontic adhesive systems using three different light curing times

BackgroundSuccess of long orthodontic treatment using orthodontic brackets depends mainly on the efficiency of the adhesive system used and it's degree of resistance in the face of stresses and foresees applied during treatment. The aim of this study was to evaluate the shear bond strength of orthodontic brackets bonded with three adhesive systems using different light curing times. Materials and methodsThe 126 human extracted premolars were randomly divided into three equal groups (n = 42) depending on the type of adhesive system used; total-etch (Transbond XT), self-etch (Transbond Plus), and self-adhesive (GC-Ortho Connect) system. Then each group was randomly subdivided into three subgroups (n = 14) based on the curing time; 1-s, 3-s, and 20-s. The shear bond strength (SBS) and adhesive remnant index (ARI) were evaluated in each subgroup using universal testing machine and stereomicroscope respectively. The data were analyzed statistically by a two-way ANOVA for SBS, and Scheirer Ray Hare Test for ARI. The significance level was set at P ≤ 0.05. ResultsThe results showed a statistically significant difference in shear bond strength at the three-time points for each adhesive system (p < 0.001) with the highest SBS value in 20-sec groups followed by 3-sec groups while 1-sec groups was the lowest. However, there was no statistically significant difference in Shear bond strength between the three adhesive systems except 20-sec groups (p < 0.001). ARI showed a statistically significant difference between all adhesive systems with the highest scores in TE groups, while the lowest in SE groups. ConclusionAll adhesive systems provided acceptable values of SBS at all curing times except the 1-sec group in SE and SA adhesive systems where the SBS values were the lowest and below the acceptable range.

Comparative evaluations of shear bond strength of mineral trioxide aggregate, Biodentine, and calcium-enriched mixture to bulk-fill flowable composite using three different adhesive systems: An in vitro study.

The objective of the study was to assess the shear bond strength of bulk-fill flowable composite resin smart dentin replacement plus when bonded to mineral trioxide aggregate (MTA)-angelus, biodentine, and calcium-enriched mixture (CEM) at two different aging periods (15 min and 72 h) using three distinct adhesive systems. In addition, the study identified the specific modes of failure (adhesive, cohesive, or mixed) using a stereomicroscope and scanning electron microscope. One hundred and twenty-six cylindrical acrylic blocks used in the study were sorted into three groups based on the bioactive substance used to fill the 3-mm diameter and 3-mm high hole in the center of each block. The groups were MTA, Biodentine, and CEM. The specimens were then divided into subgroups based on the aging interval (15 min and 72 h) of the bioactive material and the adhesive system used (two-step total-etch, two-step self-etch [SE], and one-step SE) while bonding to the restorative bulk-fill flowable composite. The shear bond strength values were measured with a universal testing machine, and the data were analyzed using two-way and one-way analysis of variance, followed by a post hoc test. The specimens were assessed under stereomicroscope and scanning electron microscope to characterize the mode of bond failure (cohesive, adhesive, or mixed). The study showed that the type of adhesive system and the time of bonding affected the shear bond strength of bulk-fill composite to the pulp capping agents (P < 0.05). For MTA, the highest bond strength was observed with two-step SE group at 15 min (18.16 ± 2.97 MPa) (P < 0.05). CEM exhibited the highest bond strength with two-step SE group at 72 h intervals (8.77 ± 1.76) (P < 0.05). The highest bond strength for biodentine group was observed with total-etch group (8.54 ± 1.35 Mpa) and two-step SE (8.19 ± 1.94 Mpa) bonded at 72 h interval (P < 0.05). The majority of the samples in the MTA group (29/42) and CEM group (20/42) showed a cohesive fracture, whereas Biodentine group (22/42) had an adhesive fracture in most of its samples. MTA demonstrated the highest bond strength with two-step SE group at 15 min, and CEM exhibited the highest bond strength with two-step SE groups at 72 h interval. For biodentine group, the type of adhesive used did not impact the bond strength values.

Effects of Endodontic Irrigants on Shear Bond Strength of Mild Universal Adhesives to Dentin

PurposeThe objective of this in vitro study was to evaluate the shear bond strength (SBS) of several universal adhesives to dentin treated with sodium hypochlorite (NaOCl), and NaOCl followed by ethylenediaminetetraacetic acid (EDTA). Materials and MethodsAdhese Universal, Scotchbond Universal, Prime & Bond Elect, Prime & Bond Active, and Optibond XTR were included in the study. SBS values were determined in self-etch mode with no pretreatment of the dentin, after a 20-minute exposure of the dentin to 6% NaOCl, and after a 20-minute exposure to NaOCl followed by a one-minute exposure to 17% EDTA. Experimental groups were repeated using a total-etch technique (except Optibond XTR). ResultsAdhesives in self-etch mode had significantly reduced SBS following dentin exposure to NaOCl (P < .05), while with a total-etch technique, only Prime & Bond Active was affected (P < .05). SBS in self-etch mode when NaOCl exposure was followed by EDTA were equal to or higher than negative control values (P < .05). For total-etch groups, Adhese Universal was negatively affected by NaOCl + EDTA exposure (P < .05). Prime & Bond Elect exhibited lower SBS following NaOCl + EDTA exposure when compared to just NaOCl exposure but was not different from the negative control (P < .05). ConclusionFor the adhesives tested, the use of 17% EDTA following NaOCl exposure negated the negative effects of NaOCl on SBS in self-etch mode. When used in total-etch mode, results varied significantly, with some adhesives performing better or worse depending on the specific testing condition.

Comparative evaluation of bond strength and color stability of polyetheretherketone and zirconia layered with indirect composite before and after thermocycling: An in vitro study.

This study investigates the interaction of zirconia and polyetheretherketone (PEEK) with indirect composite in fixed dental prostheses. This investigation aimed to assess the shear bond strength (SBS) and color stability of zirconia and PEEK before and after aging, addressing critical concerns in dental restorative applications. The current in vitro study used 96 samples, 48 of which were divided into two groups, zirconia and PEEK, before and after thermocycling. A dual-axis chewing simulator was used for thermocycling. SBS was measured using a universal testing machine, and color stability was checked using a reflective spectrophotometer. Ninety-six samples were categorized into zirconia and PEEK groups, each with subgroups undergoing thermocycling. Samples were prepared using computer-aided design/computer-aided manufacturing milling and veneered with composite resin. Thermocycling involved 10,000 cycles, simulating stress levels equivalent to approximately 1 year of clinical use. SBS was assessed using standardized tests. Stereomicroscopic analysis was performed to evaluate the type of failure. Color stability of the core materials with indirect composite was done using a spectrophotometer before and after aging. Statistical analysis included paired t-tests and independent t-tests in SPSS software. The results revealed that SBS values for composite on PEEK decreased from 13.86 ± 0.164 MPa before thermocycling to 13.46 ± 0.185 MPa after thermocycling, with a significant difference (P < 0.005). However, both pre- and postthermocycling values for PEEK were higher than zirconia. The t-test confirmed the lower bond strength of composite to zirconia, with a noteworthy improvement after aging. Stereomicroscopic images revealed adhesive failure for the zirconia group and mixed (adhesive and cohesive) failure for the PEEK group. ΔE values were 3.21 ± 0.127 and 2.93 ± 0.142 for zirconia and PEEK groups, respectively (P < 0.005). Within the limitations of this study, it can be deduced that PEEK is a feasible substitute for zirconia when used in conjunction with indirect composite for the fabrication of dental prostheses.

Effect of Different Primers on the Shear Bond Strength of Orthodontic Brackets Bonded to Reinforced Polyetheretherketone (PEEK) Substrate.

This in vitro study assessed the effect of different primers on the shear bond strength (SBS) and adhesive remnant index (ARI) of orthodontic brackets bonded to reinforced polyetheretherketone (PEEK) substrate. A total of 40 specimens were randomly distributed to two groups based on the primer used for orthodontic bonding: group 1 (control)-Transbond XT adhesive with Visio.link primer and group 2 (test)-orthodontic adhesive (Transbond XT) with traditional orthodontic primer. After bonding, specimens were thermocycled followed by SBS testing and ARI scoring of debonded specimens. Data were analyzed using the unpaired independent t-test and the Chi-square test. Group 1 specimens showed significantly higher SBS values (21.38 ± 1.48 MPa) compared to group 2 specimens (18.63 ± 1.29 MPa) (p < 0.0001). Adhesive remnant index scores showed no significant variations in bond failure modes and distributions between groups. The SBS obtained by the tested primers exceeded the clinically recommended value. Consequently, there is a comparable clinical application for both tested primers in orthodontic bonding, especially the traditional orthodontic primer, where the availability of Visio.link in clinical practice is not ensured.

Effect of surface treatment strategies on bond strength of additively and subtractively manufactured hybrid materials for permanent crowns

ObjectivesThe purpose of this study is to evaluate the bond strength of different computer-aided design / computer-aided manufacturing (CAD/CAM) hybrid ceramic materials following different pretreatments.MethodsA total of 306 CAD/CAM hybrid material specimens were manufactured, n = 102 for each material (VarseoSmile Crownplus [VSCP] by 3D-printing; Vita Enamic [VE] and Grandio Blocs [GB] by milling). Each material was randomly divided into six groups regarding different pretreatment strategies: control, silane, sandblasting (50 μm aluminum oxide particles), sandblasting + silane, etching (9% hydrofluorics acid), etching + silane. Subsequently, surface roughness (Ra) values, surface free energy (SFE) were measured. Each specimen was bonded with a dual-cured adhesive composite. Half of the specimens were subjected to thermocycling (5000 cycles, 5–55 °C). The shear bond strength (SBS) test was performed. Data were analyzed by using a two-way analysis of variance, independent t-test, and Mann-Whitney-U-test (α = 0.05).ResultsMaterial type (p = 0.001), pretreatment strategy (p < 0.001), and the interaction (p < 0.001) all had significant effects on Ra value. However, only etching on VSCP and VE surface increased SFE value significantly. Regarding SBS value, no significant difference was found among the three materials (p = 0.937), while the pretreatment strategy significantly influenced SBS (p < 0.05). Etching on VSCP specimens showed the lowest mean value among all groups, while sandblasting and silane result in higher SBS for all test materials.ConclusionsThe bond strength of CAD/CAM hybrid ceramic materials for milling and 3D-printing was comparable. Sandblasting and silane coupling were suitable for both millable and printable materials, while hydrofluoric etching should not be recommended for CAD/CAM hybrid ceramic materials.Clinical relevanceSince comparable evidence between 3D-printable and millable CAD/CAM dental hybrid materials is scarce, the present study gives clear guidance for pretreatment planning on different materials.

Assessment of the Additive Effect of Remineralizing Agents in Combination With Fluoride Releasing Adhesives in the Prevention of Enamel Decalcification in Orthodontic Patients: An In Vitro Study.

Introduction Incorporation of remineralizing agents with fluoride-releasing bracket adhesives may prevent the development of white spot lesions (WSL) or reverse the established WSL in patients undergoing fixed orthodontic treatment. We aimed to find out how effectively casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and fluoride varnish (FV) can remineralize teeth when mixed with fluoride-releasing orthodontic adhesive. Materials and methods We randomly assigned a total of 60 premolar teeth, therapeutically extracted for orthodontic purposes, into two equal groups. Group I (n = 30) utilized fluoride-releasing adhesive (FR), and Group II (n = 30) bonded with non-fluoride adhesive (NFR). Based on the applied remineralizing agent, we further divided each of the two groups into three equal subgroups of 10: Group IA (FR+FV), Group IB (FR+CPP-ACP), Group IC (control-only FR), Group IIA (NFR+FV), Group IIB (NFR+CPP-ACP), and Group IIC (control-only NFR). Following bonding procedures, all the samples underwent pH cycling for 28 days, where the enamel samples were immersed in 20 ml of demineralizing solution for three hours, followed by immersion in 30 ml of remineralizing solution for 17 hours. The samples were analyzed for shear bond strength (SBS) on a universal testing machine and hardness values (HV) by the Vickers microhardness test (VMT) using the indentation method. We also evaluated the adhesive remnant index (ARI) scores to determine the site of bracket failure. Statistical analysis The shear bond strength (SBS) and hardness value (HV) were expressed as the mean, standard deviation (SD), and median for each subgroup. We used the non-parametric Kruskal-Wallis test to analyze the SBS and HV, followed by the Dunn-Bonferroni test for intra-pair differences. The ARI score was expressed as the frequency of the percentage distribution, and the difference in the distribution of ARI scores between the groups was assessed by the Cochran chi-square test. The probability (p) value equal to or less than 0.05 was considered statistically significant. Results The results show that Group IB, bonded with a fluoride-releasing adhesive and a CPP-ACP remineralizing agent surface treatment, has the highest HV of300.23 units. Group IIC (only NFR) has the lowest hardness of153.3 units, which is statistically significant (p < 0.001). However, the ARI scores are not statistically significant between the groups tested. Conclusion The bond strength of the adhesive and the surface hardness of the enamel increased with the addition of fluoride varnish and CPP-ACP to both the fluoride-releasing and non-fluoride-releasing adhesives.

Effects of different plasma treatments on bonding properties of zirconia

This in vitro study was to evaluate the effect of different non-thermal atmospheric pressure plasma (NTP) on shear bond strength (SBS) between yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) and self-adhesive resin cement. In this study, The Y-TZP specimens were divided into 4 groups according to the surface treatment methods as follows: Control (no surface treatment), Sb (Sandblasting), AP(argon NTP), and CP(20 % oxygen and 80 % argon combination NTP). Y-TZP specimens were randomly selected from each group to observe and test the following indexes: scanning electron microscope to observe the surface morphology; atomic force microscope to detect the surface roughness; contact angle detector to detect the surface contact angle; energy spectrometer to analyze the surface elements. Then, resin cement (Rely X–U200) was bonded to human isolated teeth with Y-TZP specimens to measure SBS. The results showed that for the SE test, the NTP group was significantly higher than the control group (p < 0.05). The results of the SBS test showed that the SBS values of the NTP group were significantly higher than those of the other groups, regardless of the plasma treatment (p < 0.05). However, there was no significant difference between groups AP and CP in a test of SBS (p > 0.05). This study shows that non-thermal atmospheric pressure plasma can improve the shear bond strength of Y-TZP by increasing the surface energy. The addition of oxygen ratio to argon is more favorable to increase the shear bond strength and is worth further investigation.

Comparative Assessment of the Shear Bond Strength of Ceramic Brackets Bonded to the Enamel Surface with a Self-adhesive System.

Objectives: This study aimed to evaluate the shear bond strength of ceramic brackets bonded to the enamel surface using Vertise Flow, with or without the application of phosphoric acid. Materials and Methods: Forty-five extracted human premolar teeth were randomly assigned to three groups (N=15) based on the adhesive used for bonding: 1) Transbond XT, etch, and bond; 2) Vertise Flow; 3) Etch and Vertise Flow. After a 500-round thermocycling procedure, the shear bond strength was measured using a universal testing machine. The samples were then evaluated under a stereomicroscope to determine failure modes, and the Adhesive Remnant Index (ARI) was measured for each group. The data were analyzed with one-way ANOVA and post-hoc Tamhane at a significance level of P<0.05. Results: The highest shear bond strength values were observed in the Transbond XT (13.5±5.38MPa), acid etch and Vertise Flow (11.2±2.89MPa), and Vertise Flow (6.2±3.16MPa) groups, respectively, in descending order. The Vertise Flow group exhibited a significantly lower shear bond strength value compared to the other two groups, with no significant difference between the latter two. Conclusion: While all three study groups demonstrated clinically acceptable shear bond strength values, Vertise Flow showed lower values compared to the other two adhesives. The Vertise Flow composite resin system, whether used alone or with acid etching, remains a suitable choice for bonding ceramic brackets, offering the advantage of a simplified bonding procedure.