Shear Bond Strength Values Research Articles

To evaluate the effect of different enamel conditioning procedures on the shear bond strength of new metal bracket on previously debonded tooth surface - An in-vitro study

To evaluate the efficacy of different enamel conditioning methods while bonding a new bracket on a previously de-bonded site, and assess the difference in shear bond strength and ARI score if any. 125 human-extracted premolars were selected. 250 premolar brackets were procured. 125 brackets were bonded on the buccal surface of the premolars using different enamel conditioning methods (bonding sequence 1) and was followed by debonding using the Instron Universal testing machine (Debonding procedure I).The remaining 125 brackets were bonded (Bonding sequence II) on the same teeth after the removal of residual adhesive. Bonding sequence II was followed by debonding (Debonding procedure II), shear bond strength calculation, and ARI score calculation. There was a significant difference in SBS between the 5 groups after initial debonding. SEP group (group 4) showed the highest SBS followed by acid etching groups (groups 3, 2, and 1). The sandblasting group (group 5) had the lowest shear bond strength value. After the second debonding, SBS was found to be highest in Group 3 {37% o-phosphoric acid (Bonding I) sandblasting (Bonding II)} followed by Group 4 {SEP (Bonding I and Bonding II)}, group 2 {acid etching (Bonding I) SEP (Bonding II)}, and group 1 (acid etching in both bonding sequences). Group 5 (sandblasting in both sequences) had the least SBS. Non-significant differences were found in ARI score of the five groups. Self-etching primer group had highest SBS and sandblasting group had least SBS after first debond. The SBS of new brackets after two debonding procedures significantly decreased but was still found to be above the required bond strength. SEP and sandblasting can be used as a substitute to acid etching technique in second time bonding of brackets as these groups had higher SBS after second debond.

Effects of Surface Textures Created Using Additive Manufacturing on Shear Bond Strength Between Resin and Zirconia.

This investigation aimed to assess the impact of additive manufacturing-generated surface textures on zirconia bond strength. Zirconia samples (n = 144) fabricated using digital light-processing (DLP) technology were categorized into 6 groups according to the type of surface conditioning (group NN: no designs, no air abrasion; group NY: no designs, with air abrasion; group GN: groove designs, no air abrasion; group GY: groove designs with air abrasion; group HN: hexagon grid, no air abrasion; group HY: hexagon grid, with air abrasion). Composite resin cylinders were cemented to the treated zirconia surfaces with dual-curing, self-adhesive resin cement (Clearfil SA Luting). The shear bond strength (SBS) was tested after water storage for 3 days or 3 days with an additional 10,000 thermocycles. The zirconia samples fabricated using DLP technology have high accuracy. The SBS of the NY, GY, and HY groups did not significantly differ after 3 days, and neither did the SBS of the NN, GN, and HN groups. The NN, NY, and HY groups exhibited reduced SBS compared to their initial values following artificial aging, while the SBS of the remaining three groups were not diminished. The GY group obtained the highest SBS value after aging. Printing grooves with air abrasion can improve the bond strength.

Comparative Evaluation of Shear Bond Strength of Tricalcium Silicate-based Materials to Composite Resin with Two Different Adhesive Systems: An In Vitro Study.

Establishing a strong bond between the pulp capping agent and the restorative material is crucial to the success of the procedure. Without this bond, there is a risk of bacterial infiltration into the pulp, leading to treatment failure. In the past, calcium hydroxide was commonly used for such treatments, but it faced challenges, including poor adhesion to dentin, dissolution over time, and the development of multiple tunnel defects. Mineral trioxide aggregate (MTA), introduced to dentistry in 1993, offered an alternative but came with drawbacks like challenging handling and extended setting times. However, in recent times, several new calcium silicate-based materials have emerged to address MTA's limitations. Two notable examples are Biodentine and MTA Plus. Biodentine, for instance, exhibits excellent sealing ability, while MTA Plus distinguishes itself with a finer particle size compared to traditional MTA. These innovative materials offer promising solutions to enhance the efficacy of pulp capping procedures. Therefore, in this research, we conducted a comparative analysis of the shear bond strength (SBS) between composite resin and three materials-MTA, MTA Plus, and Biodentine. We examined the effects of applying two distinct adhesive systems in order to evaluate their influence on the bond strength. A total of 60 acrylic blocks were evenly distributed into three groups, each containing 20 blocks-group I received Biodentine, group II was assigned MTA, and group III received MTA Plus. The respective test materials were compacted into the holes within the blocks. Following this, the samples were incubated for a period of 72 hours. Subsequently, the samples were divided into two subgroups, each consisting of 10 blocks-the self-etch and the total-etch subgroup. The SBS values were then carefully measured for analysis. The SBS of the Biodentine group demonstrated a significantly higher value when compared to the other groups. It's worth noting that when the self-etch adhesive system was employed, the SBS of all the groups experienced a significant reduction. Biodentine cement proves to be an effective choice for pulp capping procedures, regardless of the specific adhesive system employed. Notably, the total-etch adhesive system consistently yields higher bond strength when compared to the self-etch adhesive system. Kumar V, Showkat I, Manuja N, et al. Comparative Evaluation of Shear Bond Strength of Tricalcium Silicate-based Materials to Composite Resin with Two Different Adhesive Systems: An In Vitro Study. Int J Clin Pediatr Dent 2023;16(S-3):S272-S277.

Influence of different curing modes on the bonding effectiveness of self-adhesive resin luting cements in combination with universal adhesives

ObjectivesThis study aimed to investigate the immediate dentin bond performance and bond durability of self-adhesive resin luting cements (RLCs) in combination with universal adhesives in different curing modes. MethodsTwo self-adhesive RLCs were used with universal adhesives as primers. They were also used alone as self-adhesive RLCs. Two multiple-step RLC systems were used as comparison materials. To measure the shear bond strength (SBS) in different curing modes, 12 specimens were prepared for each group. Stainless-steel rods were bonded to bovine dentin, and the bonded specimens were assigned to the baseline group (stored for 24 h) and artificially aged group (thermal cycling [TC], 10,000 cycles). After each storage period, the SBS of the bonded specimens was measured. The Knoop hardness number (KHN) of the cured RLCs was measured with or without primer application in different curing modes at 24 h and after 10,000 TC. The representative RLC/dentin interfaces were observed using scanning electron microscopy (SEM). ResultsDentin SBS was significantly influenced by the RLC system but not by the curing mode. Self-adhesive RLCs alone showed significantly lower SBS values than self-adhesive RLCs with primer regardless of the curing mode or storage period. The storage period, curing mode, and RLC system significantly influenced the KHN. SignificanceThe use of universal adhesives as a primer may help enhance the immediate dentin bond performance and bond durability of self-adhesive RLCs.

Shear bond strength of a RMGIC for orthodontic bracket bonding to enamel

ObjectiveTo evaluate the shear bond strength (SBS) of a restorative resin-modified glass ionomer cement (RMGIC) for orthodontic bracket bonding.Materials and methodsOne hundred twenty-one human teeth were randomly divided into 11 groups (n = 11) according to the surface treatment applied (H3PO4 ± Transbond Plus (TSEP) or Scotchbond Universal (SU)), and the adhesive used (Riva LC HV (RIVA), Fuji Ortho (FUJI), and Transbond XT (TXT)). For each sample, a metal button was bonded. SBS tests were performed at 1 week and debonded specimens were observed for failure modes determination. One-way ANOVA followed by Tukey’s post hoc test was used to compare SBS differences and Fisher’s exact test to analyze the failure modes (p < 0.05).ResultsTSEP + FUJI and H3PO4 + SU + TXT showed the highest SBS values while H3PO4 + TSEP + RIVA showed the lowest value. Cohesive failure and mixed failure were found in the groups with SU and TXT and adhesive failure in the other groups.Discussion/ConclusionsThe bonding of orthodontic attachments to enamel could be performed with any of the three materials studied. The use of a universal adhesive in the bonding protocol could optimize the adhesion values. Clinical studies would be needed to confirm the results obtained.

Comparative Evaluation of Shear Bond Strength, Adhesive Remnant Index and Cytotoxicity of Different Orthodontic Adhesives: An In-vitro Study

Introduction: Orthodontic adhesives should possess adequate bond strength and biocompatibility. Inadequate bond strength may lead to bond failures, and if the adhesive is not biocompatible, it may result in allergic reactions. Therefore, it is of prime importance to study the cytotoxicity and Shear Bond Strength (SBS) of commercially available orthodontic materials. Aim: This study aimed to comparatively evaluate in-vitro cytotoxicity, the Adhesive Remnant Index (ARI), and SBS of various orthodontic adhesives. Materials and Methods: This in-vitro study was conducted in an institutional setting as a collaborative effort between the Department of Orthodontics and White Lab-Blue Lab at Saveetha Dental College and Hospital, Chennai, India, from July 2023 to August 2023. Forty extracted human premolar teeth were bonded with four different ARI adhesives (U Bond, Enlight, Transbond XT, Aqualine LC) (n=10/group) and mounted on acrylic blocks. They were evaluated for SBS using a Universal Testing Machine (UTM), ARI using Scanning Electron Microscopy (SEM), and cytotoxicity using the MTT {3-(4, 5-dimethylthiazolyl2)-2, 5-diphenyltetrazolium bromide} assay on Human Gingival Fibroblast Cells (HGFC). Statistical analysis was performed using One-way ANOVA, with a post-hoc test for pairwise comparison to evaluate the SBS values, and the Kruskal-Wallis Test to analyse ARI inter group scores and cytotoxicity levels. Statistical Package for the Social Sciences (SPSS) software (Version 23.0) was used to conduct the statistical tests. Results: Significant differences in SBS values (p=&lt;0.001) and ARI scores (p=&lt;0.001) were noted between the different adhesives. No significant difference (p-value=0.534) in cytotoxicity was observed among all adhesives, with all exhibiting acceptable levels of biocompatibility. Conclusion: Primer-based adhesive (Transbond XT) demonstrated the highest SBS and ARI scores among the various orthodontic adhesives, with acceptable levels of biocompatibility. No significant difference was found between the conventional primer-based adhesive (Transbond XT) and the Single Component Adhesive (SCA) (Aqualine LC). Therefore, this study advocates for the use of SCA in routine clinical practice.

Effect of universal adhesive pretreatments on the bond strength durability of conventional and adhesive resin cements to zirconia ceramic.

This study aimed to evaluate the effect of pretreatment of three different universal adhesives (Single Bond Universal [SBU], All-Bond Universal [ABU], and Prime&Bond universal [PBU]) on the bonding durability of an adhesive (Panavia F 2.0, PF) and a conventional (Duo-Link, DL) resin cements to air-abraded zirconia. Rectangular-shaped zirconia specimens were prepared. The chemical composition and surface energy parameters of the materials were studied by Fourier transform infrared spectroscopy and contact angle measurement, respectively. To evaluate resin bonding to the zirconia, all the bonding specimens were immersed in water for 24 h and the specimens to be aged were additionally thermocycled 10000 times before the shear bond strength (SBS) test. The materials showed different surface energy parameters, including the degree of hydrophilicity/hydrophobicity. While the DL/CON (no pretreatment) showed the lowest SBS and a significant decrease in the value after thermocycling (P < .001), the PF/CON obtained a higher SBS value than the DL/CON (P < .001) and no decrease even after thermocycling (P = .839). When the universal adhesives were used with DL, their SBS values were higher than the CON (P < .05), but the trend was adhesive-specific. In conjunction with PF, the PF/SBU produced the highest SBS followed by the PF/ABU (P = .002), showing no significant decrease after thermocycling (P > .05). The initial SBS of the PF/PBU was similar to the PF/CON (P = .999), but the value decreased after thermocycling (P < .001). The universal adhesive pretreatment did not necessarily show a synergistic effect on the bonding performance of an adhesive resin cement, whereas the pretreatment was beneficial to bond strength and durability of a conventional resin cement.

Effect of various irrigation protocols and antioxidant application on bonding performance of two adhesive systems to coronal dentin.

The aim was to evaluate the effect of different irrigation protocols and antioxidants application on the shear bond strength (SBS) of two different adhesive systems to deep coronal dentin at different temperature. One hundred and twenty human premolar teeth were cut longitudinally in two halves, then the prepared specimens were allocated into four main groups according to the irrigation protocols; Distilled water (control), Sodium hypochlorite (NaOCl) + Ethylenediamine Tetra-acetic Acid (EDTA), and NaOCl + Editronate (HEDP), two subgroups according to irrigation solutions temperature; 4°C and 37°C, two divisions according to grape seed extract (GSE) application (with and without), and two subdivisions according to the applied adhesive systems; OptiBond-All-In-One (OPT) and ScotchBond Universal (SBU). Adhesives were applied in self-etch (SE) mode and resin composite material discs were built. Specimens were kept in distilled water for 24-h at 37°C before SBS testing. Four-way ANOVA and Tukey HSD tests were used for data analysis (α=0.05). 4°C irrigants solution temperature showed the least significant SBS values, distilled water group showed significantly higher SBS values compared to NaOCl + EDTA and NaOCl + HEDP groups respectively. GSE application improved dentin bond strength significantly within each adhesive. Increasing the temperature of the irrigation solutions has significantly enhanced the SBS of coronal dentin. Antioxidants application following different irrigation protocols has improved the SBS. Key words:Irrigation protocols, temperature, bond strength, coronal dentin, antioxidant, adhesive systems.

Assessment of a highly-filled flowable composite for the repair of indirect composites.

To compare the shear-bond-strength (SBS) of a highly-filled-flowable composite (HFFC) and a paste-type composite for indirect composite repair and to evaluate the effect of different surface treatments (ST), concerning the composite repair protocol. Eighty-four 5 × 5 × 2 mm cylindrical specimens were prepared using Gradia Plus and SR Nexco indirect composite materials. The samples were thermocycled 5,000 times. According to the ST, the samples were divided into three groups (control, bur, and air-abrasion). After ST, the sample subgroups were divided into two sub-groups according to the repair material: paste-type composite and HFFC (n = 7). Another 5,000 cycles of aging were performed. SBS values were measured with a universal testing machine (Shimadzu, Japan). Shapiro-Wilk, 3-way ANOVA, and Tukey HSD test were used to evaluate data (P < 0.05). ST was considered significant for SBS (P < 0.001). The mean values were (13.9 ± 5.7), (17.0 ± 6.4), (20.4 ± 4.9) MPa for the control, bur and phosphoric acid, and air-abrasion groups, respectively. The surface treatment and repair material interaction was considered significant for SBS (P = 0.044). The highest mean bond strength (24.5 ± 4.5 MPa) was observed for the interaction of SR Nexco, air-abrasion ST, and HFFC repair. Repairing with HFFC following air abrasion might enhance the SBS for indirect composite restorations.

Effect of casein phosphopeptide-amorphous calcium phosphate, Riva Star, and Moringa oleifera-based nano-silver fluoride on caries affected dentin remineralization bonded to composite resin.

This study aims to assess the effects of the most recent remineralizing agents, casein phosphopeptide-amorphous calcium phosphate (CPP-ACP), CO2 laser irradiation + topical fluoride (CO2 laser + TF), and Nanosilver fluoride - M. oleifera (NSF-MOLE), on the shear bond strength (SBS) and bond failure between resin composite and remineralized caries affected dentin (CAD). Fifty human molars with occlusal caries reaching approximately halfway through the dentin were immersed in a 4% thymol solution. The infected dentin was removed using an excavator and the CAD surface was exposed. The sample was allocated into five groups (n=10) based on the remineralizing agent applied. Group 1: no remineralizing agent, group 2: CPP-ACP, group 3: Riva Star, group 4: NSF:MOLE, and group 5: (CO2 laser + TF). The shear bond testing procedure was conducted utilizing a universal testing machine and a stereo-microscope was used to study the failure pattern. The researchers utilized a one-way analysis of variance. The Tukey post hoc test was conducted for multiple comparison tests. Group 4 (NSF-MOLE) (13.77±1.94 MPa) treated testers recognized the highest bond values of tooth color restoration to the CAD surface. Nonetheless, group 1 test samples with no mineralization unveiled the minimum outcome of bond integrity (9.12±1.14 MPa). Intergroup comparison exploration showed that group 2 (CPP-ACP), group 4 (NSF-MOLE) (13.77±1.94 MPa), and group 5 (CO2 laser + TF) established comparable values of SBS. Furthermore, group 3 (Riva Star) displayed better SBS than group 1 but lower than group 2, group 4, and group 5. Remineralization of CAD using modern regimes (CPP-ACP, NSF-MOLE, and CO2 laser + TF has the potential to be used to enhance the bond strength of CAD to composite restoration.

The impact of CO2 laser on the bond strength of translucent zirconia and traditional zirconia with the resin cement: In vitro study

Background/Aim: The aim of this study is to compare the impact of CO 2 laser on traditional zirconia and translucent zirconia in terms of the bonding strength to resin cement. Material and Methods: In this in-vitro study 20 zirconia disks (10 mm diameter and 2 mm thickness) were assigned to two groups (n = 10). Group 1: 10 discs of traditional zirconia, Group 2: 10 discs of translucent zirconia, CO 2 lasers were used for pretreatment of zirconia surface, respectively. Dentinal disks were cemented on zirconia disk using dual-curing resin cement. Shear bond strength tests were performed at a crosshead speed of 1 mm/min after 24 h distilled water storage. Data was analyzed by T Student's test. Results: The means and standard deviations of shear bond strength values in Group 1, and Group 2 were 1.15, 0.38, 1.99 , 0.65 MPa respectively. Data showed that application of CO 2 laser resulted in a significant higher shear bond strength of resin cement to translucent zirconia ceramics (p &lt; 0.05). Conclusions: Application of CO 2 laser treatment (3W) increases the bond strength to the resin cement of translucent zirconia compared to traditional zirconia.

Influence of Diabetes Mellitus and Universal Adhesive Application Mode on the Bond Strength of Composite Resin to Dentine.

The aim of the current study was to evaluate the influence of diabetes mellitus and the mode of applying a universal adhesive on the shear bond strength of composite resin to dentin. Forty teeth were extracted from diabetic individuals who had been living with diabetes for a period of 5 to 15 years. These forty teeth were divided into two groups: twenty molars from patients with type 1 diabetes and twenty molars from patients with type 2 diabetes. The remaining twenty sound human molars were collected from non-diabetic patients. The collected teeth were assigned into 3 groups, and each group was further divided into 2 subgroups. Group A (n = 20): non-diabetic (ND) where sub group IA: Universal adhesive applied in the total-etch mode (n = 10) and sub group IIA: Universal adhesive applied in the self-etch mode (n = 10). Group B (n = 20): diabetic type 1 (D1) where sub group IB: Universal adhesive applied in the total-etch mode (n = 10) and sub group IIB: Universal adhesive applied in the self-etch mode (n = 10). Group C (n = 20): diabetic type 2 (D2). Where Sub group IC: Universal adhesive applied in the total-etch mode (n = 10) and sub group IIC: Universal adhesive applied in the self-etch mode (n = 10). A Teflon mold measuring 3mm in diameter was attached to the dentin surface, used to build Filtek Z550 to a height of 3mm. The specimens were fixed to the universal testing to measure shear bond strength. There was a statistically significant difference of Mean ±SD of shear bond strength among the three tested groups. In group A, the Mean ±SD were (21.710 ± 0.638), it was decreased in group B to (14.626 ± 0.726) and group C to (17.740 ± 0.668). Subgroup I had lower shear bond strength values than subgroup II in all tested groups. The difference between each subgroup in groups A, B, and C was significant. 1. Diabetes mellitus has an adverse effect on the shear bond strength of composite to dentine. 2. Type 1 diabetes mellitus significantly reduces the shear bond strength of composite resin to dentin. 3. Shear bond strength of the universal adhesive was higher when applied to dentin using the self-etch mode, as compared to the total etch mode, in all groups, regardless of whether the participants had diabetes or not. Key words:Diabetes Mellitus, Universal Adhesive, Application Mode, Shear bond Strength, Dentine, Composite.

Touch-cure activation by marketed universal resin luting cements of their associated primer to dentin.

The aim of this study was to investigate the dentin shear bond strength (SBS) and bonding interface of three recently developed "universal" resin luting cements based on different modalities. The dentin SBS and interfacial analysis of three recently launched "universal" resin luting cements, namely, G-Cem One, RelyX Universal and Panavia SA cement universal, were studied. All bonding protocols, including the previous use of their dedicated primer or universal adhesive in touch-cure mode or light-cure mode were performed. Variolink Esthetic LC used in conjunction with Scotchbond Universal Plus was used as a control group. For each group (n = 9), 10 specimens were tested for dentin SBS and two were examined by scanning electron microscopy. SBS were analyzed by two-way ANOVA followed by Dunnett's test. SBS values showed that the three "universal" resin luting cements tested exhibit different adhesive behaviors. G-Cem One with its touch-cure activated primer had a greater SBS to dentin (25.5 MPa) than that of the control group (22.1 MPa). "Universal" resin luting cements have variable efficacy when used in self-curing mode. The touch-curing mode is also of concern but may show high potential for some formulations.

Shear Bond Strength of Simulated Single-Retainer Resin-Bonded Bridges Made of Four CAD/CAM Materials for Maxillary Lateral Incisor Agenesis Rehabilitation.

Maxillary lateral incisor agenesis (MLIA), treated orthodontically by space opening, requires complimentary aesthetic rehabilitation. Resin-bonded bridges (RBBs) can be equated as interim rehabilitation until skeletal maturity is achieved to place an implant-supported crown or as definitive rehabilitation in case of financial restrictions or implant contraindications. Scientific evidence of the best material must be confirmed in specific clinical situations. Computer-aided design and computer-aided manufacturing (CAD/CAM) materials are promising versatile restorative options. This study aimed to identify a straightforward material to deliver interim or definitive RBBs for nonprepared tooth replacement in MLIA. Single-retainer RBB made from CAD/CAM ceramic blocks (Vita Enamic [ENA], Suprinity [SUP], and zirconia [Y-ZPT]) and a three-dimensional (3D) printed material (acrylonitrile butadiene styrene [ABS]) were evaluated by shear bond strength (SBS) and mode of failure, after adherence to an artificial tooth with RelyX Ultimate used in a three-step adhesive strategy. The load to fracture (N) was recorded, and the mean shear stress (MPa) was calculated with standard deviations (SD) for each group and compared between materials using boxplot graphics. One-way analysis of variance (ANOVA) followed by the Tukey-Kramer post hoc test was used to compare the differences (α = 0.05). A meta-analysis focusing on CAD/CAM materials evaluated the magnitude of the difference between groups based on differences in means and effect sizes (α = 0.05; 95% confidence interval [CI]; Z-value = 1.96). Failure mode was determined by microscopic observation and correlated with the maximum load to fracture of the specimen. The mean ± SD SBS values were ENA (24.24 ± 9.05 MPa) < ABS (24.01 ± 1.94 MPa) < SUP (29.17 ± 4.78 MPa) < Y-ZPT (37.43 ± 12.20 MPa). The failure modes were mainly adhesive for Y-ZPT, cohesive for SUP and ENA, and cohesive with plastic deformation for ABS. Vita Enamic, Suprinity, Y-ZPT zirconia, and 3D-printed ABS RBBs are optional materials for rehabilitating MLIA. The option for each material is conditioned to estimate the time of use and necessity of removal for orthodontic or surgical techniques.

Effect of non-thermal plasma treatment and resin cements on the bond strength of zirconia ceramics with different yttria concentrations.

To investigate the effect of different surface treatments and resin cements on the shear bond strength of zirconia ceramics with different yttria concentrations. Zirconia blocks characterized by different yttria concentrations [Vita YZ HT (HT), Vita YZ ST (ST) and Vita YZ XT (XT)] were used to prepare disc-shaped specimens (n=252). Specimens prepared to investigate shear bond strength (SBS), water contact angle and surface roughness (Ra) were divided into four subgroups; control (C), sandblasting (S), sandblasting+nonthermal plasma treatment (SNTP) and nonthermal plasma treatment (NTP). For SBS testing, specimens were further divided into two groups (n=108) according to the luting cement used [Panavia F2.0 (P)and Rely X U200 (R)]. The water contact angles were determined by sessile drop technique and Ra was analyzed with optical profilometer. SBS tests were performed in a universal testing machine at a crosshead speed of 0.5 mm/min. The data sets were statistically analyzed with two and three-way ANOVAs followed by post-hoc comparisons (α=0.05). The water contact angle and Ra data were significantly affected by surface treatments. The mean Ra values of ST and XT were significantly lower than HT for the surface treatment groups of C and NTP. The SBS values were significantly different among the groups subjected to different surface treatments. The mean SBS values of surface treatment groups (S, SNTP and NTP) when cemented with R were significantly higher than the groups of C (p<0.05). For the tested zirconia ceramics with different yttria concentrations, non-thermal plasma activation helps to improve SBS and is a promising tool in practical use.

Shear bond strength between standard or modified zirconia surfaces and two resin cements incorporating or not 10-MDP in their matrix

ObjectiveThis study aimed first to compare the shear bond strength between zirconia samples luted to enamel with a 10-MDP- containing resin cement (Panavia F2.0, Kuraray, Japan) and those luted with a resin cement using a separated 10-MDP monomer-containing bottle (Panavia V5, Kuraray, Japan). The second objective was to evaluate the bond stability after 150 days of aging in water, between enamel and zirconia ceramic surface enhanced with a glass-ceramic coating. Materials and methods80 specimens composed of ceramic cylinders and enamel disks were obtained, within eight experimental groups (n = 10). 60 zirconia cylinders (Katana STML zirconia, Kuraray, Japan) were assigned to 3 groups according to their surface treatment: milled/sintered surface (ZRCT), tribochemical silica-coating (Cojet™ Sand, 3 M ESPE, Seefeld, Germany) (ZRTC), and glass-ceramic coating (IPS e.max Zirpress) (ZRZP). 20 cylinders of lithium disilicate had a milled surface (IPS e.max CAD, Ivoclar-Vivadent, Schaan, Liechtenstein) (ECAD). The cylinders of each group were further divided into two subgroups according to the resin cement used: Panavia F2.0 (-PF) and Panavia V5 (-PV). All specimens were stored in distilled water for 150 days before shear bond strength (SBS) tests. The fracture mode was analyzed, and data were statistically computed (two-way ANOVA, post hoc Tukey test, p < 0.05, SPSS, IBM, v26). ResultsThe ECAD-PF group recorded the highest SBS values (31.75 ± 2.2), and the ZRCT-PF group recorded the lowest values (5.59 ± 1.1). The two-way ANOVA test showed that ceramic surface treatment had a statistically significant effect on SBS (F (3,72) = 38.95, p < 0.001) while the type of ARC did not (F (1,72) = 2.40, p = 0.126). Tukey’s post hoc test revealed no statistical difference between the ZRZP and the ZRTC or ECAD groups. ConclusionWithin the limitations of this study, the PV resin achieved similar shear bond strength results between tribocoated zirconia and enamel compared to the one for glass-ceramic and enamel. Furthermore, a long-term durable bond, similar to the glass-ceramic one, was achieved with the heat pressed ceramic coated specimens. Thus, this new surface treatment could be recommended for anterior cantilever bridges for its fracture resistance and bonding ability.

Effect of Nd:YAG and 980nm Diode laser irradiation as a hypersensitivity treatment on shear bond strength of metal orthodontic brackets to enamel

Lasers are one of the tooth hypersensitivity treatments. This study aimed to determine the effect of irradiation of Nd:YAG 1064nm and 980nm Diode lasers, used for hypersensitivity treatment, on the shear bond strength (SBS) of metal orthodontic brackets to enamel. Ethylenediaminetetraacetic acid (EDTA) was used to simulate sensitivity in 70 extracted human premolars. The teeth were radiated with 1w Nd:YAG, 1.5w Nd:YAG, 1w Diode, or 1.5w Diode. All samples were incubated at 37° for 24 hours, after bonding the metal brackets. SBS values and adhesive remnant index (ARI) for each tooth was recorded. One-way analysis of variance (ANOVA) and Kruskal-Wallis test were used to compare the mean SBS and the distribution of ARI scores between the study groups, respectively. The SBS mean from the highest to the lowest were in 1w Diode (25.71Mpa), 1w Nd:YAG (24.66Mpa), 1.5w Diode (23.08Mpa), control (21.68Mpa) and 1.5w Nd:YAG (21.53Mpa) groups. No statistically significant difference existed between different groups, in terms of SBS (p=0.211) and ARI distribution (p=0.066). The application of Nd:YAG and 980nm Diode lasers to treat tooth hypersensitivity did not change the SBS of metal orthodontic brackets to the enamel and thus, are harmless to use for orthodontic patients.

Conditioning of PEEK Implant Abutment Surfaces Using Photodynamic Therapy, Nd:YAG Laser, and Conventional Methods to Evaluate Shear Bond Strength.

Objective: This study was done to evaluate shear bond strength (SBS) and modes of failures after different surface treatment modalities on polyetheretherketone (PEEK) implant abutments. Materials and methods: Seventy-five PEEK implant abutment specimens were randomly distributed into five groups based on surface treatment methods: Group I: No treatment, Group II: methylene blue-mediated photodynamic therapy (MB-PDT), Group III: neodymium-doped yttrium aluminum garnet (Nd:YAG) laser, Group IV: Sulfuric acid (H2SO4), and Group V: Sandblasting (Sb). The measurements for SBS and failure modes for PEEK implant abutment specimens were evaluated via Universal Testing Machine and Stereomicroscope, respectively. Two-way analysis of variance and Tukey's post-hoc test (p > 0.05) were used for the statistical analysis. Moreover, the Shapiro-Wilk normality test was also performed for normality. Results: The SBS mean values and standard deviations in megapascals (MPa) for PEEK abutment specimens with different surface pretreatment groups are shown in Table 1 and Fig. 1. The control group had the lowest SBS (9.67 ± 2.1 MPa), while the highest SBS was observed in Group II (MB-PDT; 17.21 ± 1.32 MPa). SBS values for Group IV (H2SO4; 15.83 ± 0.63 MPa) and Group III (Nd:YAG laser; 16.91 ± 2.10 MPa) were similar to Group II (MB-PDT; p > 0.05). The SBS values for the sandblasted specimens (13.90 ± 1.87 MPa) were not significantly different from the control group (p > 0.05). Conclusions: The PEEK implant abutment surfaces treated with MB-PDT and Nd:YAG laser expressed significantly improved SBS.

Shear bond strength of MDP-containing light-cured veneer adhesive system to zirconia with different surface preparations

This study aimed to evaluate the effects of different surface preparation techniques on the surface microstructure, the shear bond strength (SBS) between zirconia and an MDP-containing light-cured veneer adhesive system, and the adhesive failure mode. Sixty-four zirconia specimens were divided into four groups based on surface preparation methods (n = 16), including zirconia sandblasting (ZSB), zirconia vitrification or glaze-on (ZVG), zirconia surface architecture technique (ZSAT), and ZSAT-ZVG combined technique (ZSATVG) groups. Sixteen lithium disilicate specimens prepared by etching with hydrofluoric acid (HF) were used as a positive control group (LDE). Surface roughness measurement and scanning electron microscopy (SEM) evaluation were performed before and after surface preparation. All specimens were then bonded with an MDP-containing light-cured adhesive system, followed by SBS testing and adhesive failure mode analysis. The ZVG and ZSATVG groups showed the greatest differential roughness value and microscopic irregularities, while the ZSAT and LDE groups had the least surface change but the most micromechanical retentive structures for resin infiltration. SBS values were significantly different among groups (p < 0.001) with the highest SBS observed in the ZSAT group, followed by the ZSB group, LDE group, ZSATVG group, and lastly, the ZVG group. There was a statistically significant difference in failure types among the surface preparation groups (p < 0.001). The ZSAT group had the highest frequency of mixed failure, followed by the ZSB group, LDE group, and the ZSATVG and ZVG groups. Establishing direct micromechanical retention within zirconia itself yields a higher bond strength than indirect micromechanical retention within a glass ceramic layer.

Evaluation of the Effect of Phosphoric Acid or Er: YAG Laser on the Shear Bond Strength of Orthodontic Brackets to Enamel Surfaces Followed by 980-Laser Assisted Bleaching: An In Vitro Study.

Introduction: The residual oxygen remained on tooth surface after bleaching may interfere with adhesion of brackets to enamel surface. This study aimed to evaluate the influence of phosphoric acid and Er: YAG laser as an etching technique on the shear bond strength (SBS) of orthodontic brackets to enamel surfaces after 980-laser-assisted bleaching. Methods: A total of 84 human premolars were recruited in the present study. Samples were divided into 6 groups including conventional bleaching with conventional etching, conventional bleaching with Er: YAG laser etching, laser-assisted bleaching with conventional etching, and Laser-assisted bleaching with Er: YAG laser etching, without bleaching with traditional etching, and without bleaching+Er: YAG laser etching. Following thermocycling, the debonding of brackets was conducted using a universal testing machine. Scanning electron microscope (SEM) microscope evaluation and adhesive remnant index (ARI) scores were assessed. The comparison of SBS values between groups was carried out by means of a one-way analysis of variance, followed by post-hoc tests. Results: The non-bleaching with conventional etching group showed the highest SBS mean value (23.45±5.16 MPa), whereas the conventional bleaching with conventional etching group represented the lowest SBS mean value (8.8±3.83 MPa). In all groups, the most common type of failure was classified as either score 1 or score 2. No significant difference was observed in terms of SBS mean between the groups (P=0.165); however, the average SBS of bleached teeth was significantly lower, compared to the non-bleached group (P=0.000). Honeycomb structure and porosity were observed following Er: YAG laser etching on the tooth surface. Conclusion: Increased bond strength of brackets was observed in bleached teeth following Er: YAG laser etching. Therefore, if necessary, bond the brackets on the same day of bleaching will be done, the application of Er:YAG laser as etching technique will can be recommended.