Sewage Sludge Research Articles

Future Directions of Sustainable Resource Utilization of Residual Sewage Sludge: A Review

With the simultaneous increase in wastewater generation and wastewater treatment rates in China, the annual production of residual sewage sludge (RSS) has been steadily rising, exceeding 70 million tons with an 80% moisture content. The sustainable resource utilization of RSS will be the predominant disposal method instead of sanitary landfilling in China. This review aimed to systematically analyze the major sustainable resource utilization technologies for RSS. Firstly, the basic characteristics of RSS in China were analyzed. A comparative analysis was conducted to assess the advantages, disadvantages, and applicability of three primary sustainable resource utilization technologies for RSS: building materials, energy utilization, and phosphorus recovery, aiming to provide clear insights for the development of future strategies. The research findings revealed that no single method can economically and environmentally address all challenges in the utilization of RSS resources. It is necessary to adopt appropriate resource utilization technologies according to the characteristics of RSS from wastewater treatment, achieving integration of pollution control and resource utilization. This review can provide scientific guidance for future sustainable utilization of RSS resources.

Utilization of industrial wastes in non-sintered bricks: microstructure and environmental impacts.

Recycling industrial solid wastes as building materials in the construction field exhibits great environmental benefits. This study designed an eco-friendly non-sintered brick by combining multiple industrial solid wastes, including sewage sludge, fly ash, and phosphorus gypsum. The mechanical properties, microstructure, and environmental impacts of waste-based non-sintered bricks (WNBs) were investigated comprehensively. The results revealed that WNB exhibited excellent mechanical properties. In addition, steam curing could further promote the strength development of WNB. The compressive strength of WNB with 10 wt% of sewage sludge reached 13.5MPa. Phase assemblage results indicated that the incorporation of sewage sludge promoted the generation of ettringite. Mercury intrusion porosimetry results demonstrated that the pore structure of WNB varies with the dosage of sewage sludge. Life-cycle assessment results revealed that the energy consumption and CO2 emission of WNB were 45% and 17% lower than those of traditional clay bricks. Overall, the development of WNB in this study provided insights into the co-disposal of industrial solid wastes.

Selective lead capture using amide-containing COFs: A novel strategy for efficient soil remediation

A critical consideration in the application of phytoremediation to remediate sludge soil contaminated with heavy metals is the potential for leaching risks that prevail prior to the efficient uptake of these metals by plants. The most cost-effective method is to use heavy metal stabilizers with selective adsorption. A novel amide-based COF material (COF-TH) has been synthesized as a heavy metal stabilizer for Pb. COF-TH exhibits significant selectivity for Pb in five-metal-mixed solutions, with a distribution coefficient KD as high as 3279 mL·g–1, which was more than 7.3 times that of other heavy metals. The maximum adsorption capacity of COF-TH for Pb was 189 mg·g–1. The adsorption fitted Langmuir model and intra-particle diffusion model, and satisfied pseudo-second-order kinetic model. The excellent selectivity and adsorption performance originate from the complexation between abundant amide groups and Pb ions. Pot experiments and leaching assays confirm that COF-TH decreased Pb leachate concentrations by 77.8 % without significantly decreasing total phytoextracted amounts of other heavy metals, due to the high selectivity of COF-TH to Pb. Additionally, its positive impact on plant growth and microbial diversity makes it a promising soil remediation agent. This investigation offers a novel approach to mitigate the leaching risk of a specific heavy metal Pb during sludge land application by integrating soil phytoremediation with stabilization techniques.

Biomethanization of rigid packaging made entirely of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate): Mono- and co-digestion tests and microbial insights

This study evaluates the anaerobic mesophilic mono- and co-digestion of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH) plastic bottles as a proxy for rigid packaging materials. Initial tests showed a 97.3 ± 0.2 % reduction in weight and an observable alteration in the surface (thinning, color fading and pitting) of the PHBH bottles after eight weeks. Subsequent tests showed that PHBH squares (3 × 3 cm) produced 400 NmL-CH4/g-VSfed, at a slower rate compared to powdered PHBH but with similar methane yield. Co-digestion experiments with food waste, swine manure, or sewage sludge showed successful digestion of PHBH alongside organic waste (even at a high bioplastic loading of 20 % volatile solids basis), with methane production comparable to or slightly higher than that observed in mono-digestion. Molecular analyses suggested that the type of co-substrate influenced microbial activity and that methane production was mainly driven by hydrogenotrophic methanogenesis. These results suggest the potential for integrating rigid PHBH packaging into anaerobic digesters.

RETRACTED: Life cycle analysis of biowaste-to- biogas/biomethane processes: Cost and environmental assessment of four different biowaste scenarios organic fraction of municipal solid waste and secondary sewage sludge

Biowaste-to-biogas processes have been introduced to design a valuable and green renewable plant to achieve a sustainable society and environment. The biomethane production process through biogas upgrading instead of designing a combined heat and power (CHP) system can be more attractive. This study presents a life cycle analysis (LCA) from both cost and environmental standpoints for four biowaste-to-biogas/biomethane process scenarios. Biogas production is achieved through anaerobic co-digestion of the organic fraction of municipal solid waste (OF-MSW) and secondary sewage sludge (S-SS), incorporating a pre-treatment process based on the dark co-fermentation process (DCFP). Each scenario offers distinct methods for utilizing the hydrogen-rich gas and biogas, with varying degrees of energy recovery and efficiency. Two sensitivity studies were conducted under various utilizations of the recovered biomethane and the anticipated electricity mix. Scenario SC-1 (CHP-from-biogas) was found to be the most co-friendly favorable in eight out of eleven impact categories (under the CML/IA technique). Further, biogas upgrading-integrated options exhibited lower impacts. Replacing biomethane instead of petrol in scenarios with upgraded biogas was identified as the most effective approach against climate change. Financial analysis indicated that all layouts are economically viable, each demonstrating a positive NPV over a 20-year period (up to $11.57 million).

Biochar from Co-Pyrolyzed Municipal Sewage Sludge (MSS): Part 2: Biochar Characterization and Application in the Remediation of Heavy Metal-Contaminated Soils.

The disposal of municipal sewage sludge (MSS) from wastewater treatment plants poses a major environmental challenge due to the presence of inorganic and organic pollutants. Co-pyrolysis, in which MSS is thermally decomposed in combination with biomass feedstocks, has proven to be a promising method to immobilize inorganic pollutants, reduce the content of organic pollutants, reduce the toxicity of biochar and improve biochar's physical and chemical properties. This part of the review systematically examines the effects of various co-substrates on the physical and chemical properties of MSS biochar. This review also addresses the effects of the pyrolysis conditions (temperature and mixing ratio) on the content and stability of the emerging pollutants in biochar. Finally, this review summarizes the results of recent studies to provide an overview of the current status of the application of MSS biochar from pyrolysis and co-pyrolysis for the remediation of HM-contaminated soils. This includes consideration of the soil and heavy metal types, experimental conditions, and the efficiency of HM immobilization. This review provides a comprehensive analysis of the potential of MSS biochar for environmental sustainability and offers insights into future research directions for optimizing biochar applications in soil remediation.

Sustainable hydrothermal co-carbonization of residues from the vegetable oil industry and sewage sludge: Hydrochar production and liquid fraction valorisation

In this study, the hydrothermal co-carbonization (co-HTC) of residues from the vegetable oil industry (pumpkin oil cake – PC, hemp oil cake – HC) and sewage sludge (SS) was investigated for the first time. The co-HTC was performed at 250 °C and a treatment time of 5 h. The effects of the mass ratio of the feedstocks (1:1, 1:3 and 3:1) on the properties of the HTC products were investigated using various analytical methods (NMR, XRD, 3D-EEM, FTIR, etc.).The co-HTC of SS with oil cakes resulted in improved fuel properties of the hydrochar and an increase in C content from 36.9 to 53.7 wt%, and an increase in the higher heating value (HHV) from 14.8 to 23.6 MJ/kg. The combination with HC gave hydrochars with a higher HHV and higher C content than the combination with PC. The hydrochar yield varied in the range of 39.4–55.3 wt%. NMR analysis revealed a higher proportion of aliphatic (∼60 %) than aromatic compounds (∼35 %) in the hydrochars, as well as a high content of orthophosphate and unsaturated fatty acids. The liquid fractions were rich in nutrients and organic compounds, but toxic to aquatic organisms. The hydrochars and liquid fractions performed well in the germination test with plant species.

Seasonal variation in abundance and characteristics of microplastic in sewage sludge from major cities across the upper stretch of River Ganga, India.

Microplastic (MP) load in urban sewage sludge could vary annually in wastewater treatment plants (WWTPs) depending on seasonal precipitation and human activities. We investigated the seasonal dynamics in abundance and characterization of MP loading in WWTPs located in two cities across River Ganga, India's ecologically sensitive upper stretch. During a 12-month seasonal sampling (pre-monsoon, monsoon, and post-monsoon), sludge samples (n = 36) (primary sludge, PS; drying bed sludge, DBS) were collected and analyzed for load, polymer types, shape, colour, and size (20-1000µm). Across the three seasons, MP concentrations (particles/kg) were found to be in the ranges of 93.4 ± 5.0 × 103-189.4 ± 11 × 103 in the PS and 39.6 ± 4.0 × 103-152.0 ± 7 × 103 in the DBS. The trend of MP loading was in the following order: monsoon > post-monsoon > pre-monsoon. The dominant MP size was 50-200µm (36.22%) followed by 20-50µm (27.65%), 200-500µm (24.55%) and 500-1000µm (11.58%). ATR-FTIR results revealed polypropylene, polyethylene terephthalate, polyvinyl chloride, and nylon dominating MP in sludge. This study highlights the importance of long-term monitoring of MP loading in sewage sludge to offer a more accurate estimate of MP contamination in sludge from WWTPs and develop a possible mechanism for its elimination to safeguard the environment.

Sewage sludge management and enhanced energy recovery using anaerobic digestion: an insight.

Sewage sludge (SS) is a potential source of bioenergy, yet its management is a global concern. Anaerobic digestion (AD) is applied to effectively valorize SS by reclaiming energy in the form of methane. However, the complex floc structure of SS hinders hydrolysis during AD process, thus resulting in lower process efficiency. To overcome the rate-limiting hydrolysis, various pre-treatment methods have been developed to enhance AD efficiency. This review aims to provide insights into recent advancements in pre-treatment technologies, including mechanical, chemical, thermal, and biological methods. Each technology was critically evaluated and compared, and its relative worth was summarized based on full-scale applicability, along with economic benefits, AD performance improvements, and impact on digested sludge. The paper illuminates the readers about existing research gaps, and the future research needed for successful implementation of these approaches at full scale.

Multicriteria approach for evaluating biowaste-valorization cases

The selection of waste-valorization projects is a complex decision process that involves many factors and variables to guarantee an appropriate definition of the best waste-management strategy to be applied for a specific waste typology. Different technological approaches can be identified based on the diverse waste types, such as fish byproducts, spent coffee grounds, used cooking oils, and sewage sludge. To identify the most suitable and sustainable method for processing each residue type, one must consider multiple criteria in the decision-making process (i.e., economic, technological, environmental, social, and political) to define a specific waste-management strategy. In this study, the analytical-hierarchy-process model is applied to evaluate waste-treatment projects based on the criteria above. This methodological approach involves several steps. First, existing state-of-the-art projects are critically reviewed to identify more advanced solutions for waste management. Second, biowaste projects are characterized by the application of multiple criteria and subcriteria. Finally, prioritized solutions are generated to elucidate the ranking of biowaste based on a hierarchical structure.

A comparative study of worm-sludge treatment reed bed planted with Phragmites australis and Arundo donax in the Mediterranean region

Sludge treatment reed bed planted (STRB) with Phragmites australis (P.australis) and Arundo donax (A.donax) was assessed in the presence of Eisenia fetida under control condition during the dry season. Worm-planted units were fed with mixed sewage sludge (dry and volatile solids of 29.44 g DS.L−1 and 24.23 g VS.L−1). Sludge loading rates (SLR) of 50, 60, and 70 kg DS m−2 year−1 were examined to assess dewatering efficiency. Surface layers in units with P.australis and A.donax achieved DS of 80 and 81% at a loading rate of 50 kg DS m−2 year−1, while their subsurface DS were 41 and 25%, respectively. Units with A.donax experienced plant loss when subjected to SLR exceeding 60 kg DS m−2 year−1. More than 10 cm of residual sludge accumulated on the top of units after a 2-month final rest. Evapotranspiration was greater in the unit with P.australis (5.23 mm day−1) compared to the unit with A.donax (4.24 mm day−1) while both were fed with 70 kg DS m−2 year−1. Water loss contributions from residual sludge layer, drained water, and evapotranspiration were 3, 46, and 51%, respectively. Units with P.australis indicated 20% higher water loss compared to units with A.donax. Although the drained water quality improved over time, it did not meet standard limits. The residual sludge layer contained macro and micronutrients, and heavy metals with a significant elemental order of N > Ca > P > S > mg > K (N:P:K = 31:8:1), Fe > Na > B > Mn > Mo and Zn > Cr > Cu > Pb > Ni > Cd. Overall, STRB could be a sustainable alternative technology to conventional sewage sludge management techniques.Graphical

The Application of Atomic Spectroscopy Techniques in the Recovery of Critical Raw Materials from Industrial Waste Streams, Part II

This month’s column is Part 2 of a contribution from my daughter Glenna, who recently completed her PhD studies in Environmental Science from the University of Copenhagen in Denmark. Her article explores the current landscape of global critical raw materials (CRM) trends in research and the applications of atomic spectroscopy (AS), including inductively coupled plasma–mass spectrometry (ICP-MS), inductively coupled plasma–optical emission spectrometry (ICP-OES), and X-ray analytical techniques in their identification of diverse industrial and environmental media, which have been essential in method validation and quantification of CRMs in complex matrices presenting high risks of interference. Some important examples to be presented include rare earth elements (REEs) in water leaching purification (WLP) residues that co-occur with radioactive materials; REEs and other metals in acid mine drainage (AMD) environments; REEs in coal combustion (fly ash) residues; arsenic (As) from groundwater treatment sediment; and platinum-group elements (PGEs) from sewage sludge. The article also classifies the different techniques in use at each stage of the CRM recovery train, investigates present challenges to each analytical method, and discusses the problem-solving tools used.

Biosolids Treated as a Nutritional Alternative for in vitro Culture of Bowdichia Virgilioides Kunth.

The safe management of sewage waste is a current concern due to population growth and waste production. Biosolids, derived from sewage sludge treatment, are globally used as organic fertilizers, aligning with Sustainable Development Goal 6 for resource recycling. However, biosafety concerns arise due to the presence of metals and microplastics in biosolids, potentially impacting soil and water. This study investigated biosolids' use for in vitro cultivation of Bowdichia virgilioides Kunth. Results indicate that while biosolids can replace traditional nutritional media, balancing their concentration is crucial for optimizing plant growth. The WPM (Wood Plat Medium) remains essential for in vitro cultivation, but substituting it with biosolids at concentrations of up to 2g L- 1 is feasible, providing similar plant development compared to the WPM medium. However, when combined, there is a complex and challenging interaction between biosolids and the culture medium.

Rate of Microelement Quantitative Changes during the Composting of Sewage Sludge With Various Bulking Agents

The composting of sewage sludge (SS) with structure-forming additives is a popular and inexpensive method for the management of biodegradable waste. During this process, a number of transformations of organic matter and nutrients occur. This study presents the rates and directions of quantitative changes in Cu, Zn, and Ni during the composting of various mixtures. The following substances were used for preparing compost mixtures: SS, sawdust, straw, and bark. These substances were mixed together in appropriate proportions as follows: C1: 45% SS + 50% sawdust + 5% straw; C2: 45% SS + 50% bark+ 5% straw; and C3: 45% SS + 35% bark + 15% sawdust + 5% straw. Single (DTPA solution) and sequential extraction methods (BCR protocol) were used for microelement mobility assessment. Compost valorization was performed in each individual composting phase. The chain relative increment analysis was used for such assessment. Additionally, the potential metal pollution in the composts was evaluated by applying the following indices: the pollutant accumulation index (PAI), heavy metal enrichment index (HMEI), and heavy metal pollution load index (HMPLI). During composting, generally, the amounts of Ni, Cu, and Zn increased in the various extracted combinations, which was independent of their susceptibility to decomposition. Despite of this, the tested composts should be considered as a source of slowly available microelements for plants. The most intense quantitative changes in metals occurred in the thermophilic phase, and the weakest changes occurred in the cooling phase. At the same time, the calculated indices indicated a lack of contamination of the composts with the analyzed metals, emphasizing their environmental safety and lack of negative impact. The bulking agents used for composting with SS did not significantly influence the intensity of the quantitative changes in the tested metals.

Life Cycle Assessment and Net Energy Analysis of an Integrated Hydrothermal Liquefaction-Anaerobic Digestion of Single and Mixed Beverage Waste and Sewage Sludge

The conversion of biomass to bioenergy is one of the approaches to creating a sustainable society. In this study, the life cycle assessment and the net energy analysis of converting mixed sewage sludge and beverage waste into bioenergy via a combined hydrothermal liquefaction-anaerobic digestion (HTL-AD) system was carried out. Primary sludge (PS), winery rose lees (RL), brewery Trub (BT), the mixture of brewery trub and primary sludge (BTPS) and the mixture of winery rose lees and primary sludge (RLPS) were the feedstocks considered. Efficient energy utilization [in form of net energy ratio (NER)], and environmental emissions were evaluated. The NER of BT (2.07) and RL (1.76) increased when mixed with PS (3.18) to produce BTPS (3.20) and RLPS (2.85). Also, the HTL phase of the combined HTL-AD system produced a greater NER than the AD phase in BT, BTPS, and PS and vice-versa in RL and RLPS. Six environmental impact categories were studied namely global warming, terrestrial acidification, ionizing radiation, terrestrial ecotoxicity, human carcinogenic toxicity, and human non-carcinogenic toxicity. RL produced the greatest environmental impact while BTPS produced the least impact, thus indicating the advantage of feedstock combination. This study shows that the combination of feedstocks for bioenergy production in an HTL-AD system does not only increase the quality and quantity of products but also increases the overall NER as well as reducting the environmental impacts. The study also proved that an integrated HTL-AD system is an energy efficient system with greater resource utilization and less environmental footprint than the constituent systems.

Optimization of activation by peroxidation and photo-assisted peroxidation of biochar produced from sewage sludge

Biochar from biomass, a cost-effective and sustainable alternative to pulverized activated carbon (PAC), often faces limitations in pore size and surface functionality. Hydrogen peroxide (H₂O₂) activation can enhance biochar's surface properties but requires large quantities and high concentrations, increasing production costs. Advanced oxidation methods, such as H₂O₂/UV radiation, can reduce H₂O₂ usage by generating highly reactive hydroxyl radicals (*OH). This study investigates biochar production from activated sewage biosolids using H2O2 activation and H2O2/UV radiation. Optimization was conducted via a central composite rotational design, varying activation parameters activation pH (1.5, 4.0, 7.0, 9.0, and 11.5) and H2O2 concentration (0, 10, 20, 30, and 40 vol), with methylene blue (MB) adsorption capacity as the metric. Characterization was performed using FTIR, SEM, EDS, XRD, and N2 adsorption/desorption techniques. Results indicated optimal biochar activation at pH 11.5 with 20 vol% H2O2. Activation pH was more significant than H2O2 concentration. Desirability curve analysis suggested that optimized parameters did not significantly enhance adsorption capacity, with desirability values at 93.053 %. Overall, H2O2 efficiently increased surface area by degrading the adsorbent, while H2O2/UV effectively removed impurities.

Laboratory and field investigations of alkali-silica reaction prevention by supplementary cementitious materials: Influence of the free alkali loading

Performance tests are often used to evaluate the effect of supplementary cementitious materials (SCMs) on alkali-silica reaction (ASR). However, these tests may be quite demanding, thus other approaches may be more efficient to identify the materials that are worthwhile testing further. This paper presents ASR expansion data obtained from outdoor exposure (2.5 years) and three accelerated laboratory tests: ASTM C1567, TI-B 51, and RILEM AAR-10. A reactive sand containing porous flint, which caused damage in structures after only a few years, was tested with Portland cement and a wide range of SCMs: fly ash, two biomass ashes, two calcined clays, sewage sludge ash, crushed brick, and glass beads. Expansion data were compared with free alkali loadings determined on companion paste samples. It was observed that no expansion occurred below around 2.4 kg/m3 free Na2Oeq in AAR-10 and outdoors (so far). Conversely, no clear trend was found with ASMT C1567 and TI-B 51 results, probably because the outcomes of these immersion tests depend on the transport properties of the specimens and interactions with the surrounding solutions. Since expansions in AAR-10 and outdoors correlate, the free alkali loading seems a promising parameter for screening how SCMs influence the risk of deleterious ASR.

Hydrodynamic disintegration effects assessment by CFD modelling integrated with bench tests

The hydrodynamic disintegration process depends, among others, on operational parameters like rotational speed or introduced energy. The study presents an interdisciplinary approach to the hydrodynamic disintegration parameters impact assessment on the internal processes and disintegration effects on the example of sewage sludge treatment. Three rotational speeds were considered, including fluid properties change at selected disintegration stages. Disintegration effects were measured in the bench tests. Soluble chemical oxygen demand (SCOD) and volatile fatty acids (VFA) were measured before and after disintegration process. The assessment of the effects of disintegration employed the disintegration degree and the assessment of the course of methane production employed biochemical methane potential (BMP) tests. Fluid properties change during the disintegration stages does not cause a significant change in the flow structure. Due to the mathematical modelling results, at 1500 rpm no cavitation phenomenon was observed. Although, the bench tests results indicates, for the rotational speed 1500 rpm, organic compounds released to the liquid were characterised by higher susceptibility to biological decomposition than those released for 2500 and 3000 rpm (as suggested by the low SCOD/VFA values for 1500 rpm). Obtained results have confirmed, that the main phenomenon responsible for the disintegration effect is mechanical shredding not cavitation.

Accelerated de-chelation of EDTA-metal complexes: A novel and versatile approach for wastewater and solid waste remediation

Industrial waste, including wastewater and solid waste, often contains toxic heavy metals that necessitate extraction and separation prior to safe disposal or reusing them. Sewage sludge incineration ash (SSIA), a non-incinerable waste, holds significant amounts of heavy metals such as iron, zinc, copper, nickel, chromium, and lead. Recovery and reuse of heavy metals from SSIA and further application of treated SSIA sludge remain challenging. Ethylenediaminetetraacetic acid (EDTA) is widely used for heavy metals chelation in different applications. While its chelation with heavy metals is rapid and easy to achieve, the de-chelation of the metal complexes is otherwise slow (∼3 days) and challenging due to their high stability constants. In this study, we investigate the recovery of heavy metals from SSIA through chelation using EDTA, and develop, for the first time, a method to rapidly de-chelate the EDTA-metal complexes through the facile chilling process (1 – 3 h) that accelerates the separation of EDTA and metal ions. A sequential precipitation of high-purity heavy metals from the EDTA-metal complexes was demonstrated with and without de-chelation. This novel and versatile method allows the separation of many valuable compounds from the treated SSIA, including regenerated EDTA, potassium hexafluorosilicate, iron phosphate, iron(III) hydroxide, iron silicate, titanium phosphate, calcium phosphate, copper(I) thiocyanate, nickel bis(dimethylglyoximate), lead(II) sulfate, and zinc sulfide. This approach opens doors for more sustainable waste management and the recovery of valuable resources from industrial waste.

Energy recovery from syngas and pyrolysis wastewaters with anaerobic mixed cultures

The anaerobic digestion of aqueous condensate from fast pyrolysis is a promising technology for enhancing carbon and energy recovery from waste. Syngas, another pyrolysis product, could be integrated as a co-substrate to improve process efficiency. However, limited knowledge exists on the co-fermentation of pyrolysis syngas and aqueous condensate by anaerobic cultures and the effects of substrate toxicity. This work investigates the ability of mesophilic and thermophilic anaerobic mixed cultures to co-ferment syngas and the aqueous condensate from either sewage sludge or polyethylene plastics pyrolysis in semi-batch bottle fermentations. It identifies inhibitory concentrations for carboxydotrophic and methanogenic reactions, examines specific component removal and assesses energy recovery potential. The results show successful co-fermentation of syngas and aqueous condensate components like phenols and N-heterocycles. However, the characteristics and load of the aqueous condensates affected process performance and product formation. The toxicity, likely resulting from the synergistic effect of multiple toxicants, depended on the PACs’ composition. At 37 °C, concentrations of 15.6 gCOD/gVSS and 7.8 gCOD/gVSS of sewage sludge-derived aqueous condensate inhibited by 50% carboxydotrophic and methanogenic activity, respectively. At 55 °C, loads between 3.9 and 6.8 gCOD/gVSS inhibited by 50% both reactions. Polyethylene plastics condensate showed higher toxicity, with 2.8 gCOD/gVSS and 0.3 gCOD/gVSS at 37 °C decreasing carboxydotrophic and methanogenic rates by 50%. At 55 °C, 0.3 gCOD/gVSS inhibited by 50% CO uptake rates and methanogenesis. Increasing PAC loads reduced methane production and promoted short-chain carboxylates formation. The recalcitrant components in sewage sludge condensate hindered e-mol recovery, while plastics condensate showed high e-mol recoveries despite the stronger toxicity. Even with challenges posed by substrate toxicity and composition variations, the successful conversion of syngas and aqueous condensates highlights the potential of this technology in advancing carbon and energy recovery from anthropogenic waste streams.Graphical