Selective Pressurized Liquid Extraction Research Articles

Comparison of Two Analytical Methods for the Determination of Traces of Veterinary Antibiotics and Steroid Hormones in Soil Based on Pressurised Liquid Extraction (PLE) and Quick, Easy, Cheap, Effective, Rugged, Safe (Modified-Quechers) Extraction

Veterinary antibiotics and steroid hormones can be present at low levels in soil. Analytical methodologies are therefore necessary to analyse these compounds at the trace level in such a complex matrix. The goal of this work was to compare Pressurised Liquid Extraction (PLE), which is usually used to extract drugs from soil, and a modified-QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) method. Furthermore, several clean-up methods were evaluated. Selective Pressurised Liquid Extraction (SPLE) and Dispersive Solid Phase Extraction (dSPE) used after PLE and QuEChERS, respectively, were tested. These techniques permit a fast and simple purification step. SPE, which is frequently used, was also evaluated. To perform this comparison, both recoveries and matrix effects were compared and the analyses were performed using liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS). SPLE and dSPE did not significantly decrease matrix effects. A tandem SPE using SAX and Strata-X cartridges offered the best efficiency. Regarding the comparison between PLE and QuEChERS, the modified-QuEChERS led to better recoveries for certain substances. No significant differences were noted in term of matrix effects. Therefore, the modified-QuEChERS method is recommended.

Selective Pressurized Liquid Extraction Technique Capable of Analyzing Dioxins, Furans, and PCBs in Clams and Crab Tissue

A selective pressurized liquid extraction technique (SPLE) was developed for the analysis of polychlorodibenzo-p-dioxins, polychlorodibenzofurans (PCDD/Fs) and dioxin-like polychlorobiphenyls (dl-PCBs) in clam and crab tissue. The SPLE incorporated multiple cleanup adsorbents (alumina, florisil, silica gel, celite, and carbopack) within the extraction cell. Tissue extracts were analyzed by high resolution gas chromatography coupled with electron capture negative ionization mass spectrometry. Mean recovery (n = 3) and percent relative standard deviation for PCDD/Fs and dl-PCBs in clam and crabs was 89 ± 2.3 and 85 ± 4.0, respectively. The SPLE method was applied to clams and crabs collected from the San Jacinto River Waste Pits, a Superfund site in Houston, TX. The dl-PCBs concentrations in clams and crabs ranged from 50 to 2,450 and 5 to 800 ng/g ww, respectively. Sample preparation time and solvents were reduced by 92 % and 65 %, respectively, as compared to USEPA method 1613.

Selective pressurized liquid extraction of pesticides, polychlorinated biphenyls and polybrominated diphenyl ethers in a whale earplug (earwax): A novel method for analyzing organic contaminants in lipid-rich matrices

Lipid-rich matrices are often sinks for lipophilic contaminants, such as pesticides, polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs). Typically methods for contaminant extraction and cleanup for lipid-rich matrices require multiple cleanup steps; however, a selective pressurized liquid extraction (SPLE) technique requiring no additional cleanup has been developed for the simultaneous extraction and cleanup of whale earwax (cerumen; a lipid-rich matrix). Whale earwax accumulates in select whale species over their lifetime to form wax earplugs. Typically used as an aging technique in cetaceans, layers or laminae that comprise the earplug are thought to be associated with annual or semiannual migration and feeding patterns. Whale earplugs (earwax) represent a unique matrix capable of recording and archiving whales’ lifetime contaminant profiles. This study reports the first analytical method developed for identifying and quantifying lipophilic persistent organic pollutants (POPs) in a whale earplug including organochlorine pesticides, polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs). The analytical method was developed using SPLE to extract contaminants from ∼0.25 to 0.5g aliquots of each lamina of sectioned earplug. The SPLE was optimized for cleanup adsorbents (basic alumina, silica gel, and Florisil®), adsorbent to sample ratio, and adsorbent order. In the optimized SPLE method, the earwax homogenate was placed within the extraction cell on top of basic alumina (5g), silica gel (15g), and Florisil® (10g) and the target analytes were extracted from the homogenate using 1:1 (v/v) dichloromethane:hexane. POPs were analyzed using gas chromatography–mass spectrometry with electron capture negative ionization and electron impact ionization. The average percent recoveries for the POPs were 91% (±6% relative standard deviation), while limits of detection and quantification ranged from 0.00057 to 0.96ngg−1 and 0.0017 to 2.9ngg−1, respectively. Pesticides, PCBs, and PBDEs, were measured in a single blue whale (Balaenoptera musculus) cerumen lamina at concentrations ranging from 0.11 to 150ngg−1.

Determination of polychlorinated biphenyls in soil and sediment by selective pressurized liquid extraction with immunochemical detection

A selective pressurized liquid extraction (SPLE) method was developed for a streamlined sample preparation/cleanup to determine Aroclors and coplanar polychlorinated biphenyls (PCBs) in soil and sediment. The SPLE was coupled with an enzyme-linked immunosorbent assay (ELISA) for an effective analytical approach for environmental monitoring. Sediment or soil samples were extracted with alumina, 10% AgNO3 in silica, and sulfuric acid impregnated silica with dichloromethane at 100°C and 2000psi. The SPLE offered simultaneous extraction and cleanup of the PCBs and Aroclors, eliminating the need for a post-extraction cleanup prior to ELISA. Two different ELISA methods: (1) an Aroclor ELISA and (2) a coplanar PCB ELISA were evaluated. The Aroclor ELISA utilized a polyclonal antibody (Ab) with Aroclor 1254 as the calibrant and the coplanar PCB ELISA kit used a rabbit coplanar PCB Ab with PCB-126 as the calibrant. Recoveries of Aroclor 1254 in two reference soil samples were 92±2% and 106±5% by off-line coupling of SPLE with ELISA. The average recovery of Aroclor 1254 in spiked soil and sediment samples was 92±17%. Quantitative recoveries of coplanar PCBs (107–117%) in spiked samples were obtained with the combined SPLE–ELISA. The estimated method detection limit was 10ngg−1for Aroclor 1254 and 125pgg−1 for PCB-126. Estimated sample throughput for the SPLE–ELISA was about twice that of the stepwise extraction/cleanup needed for gas chromatography (GC) or GC/mass spectrometry (MS) detection. ELISA-derived uncorrected and corrected Aroclor 1254 levels correlated well (r=0.9973 and 0.9996) with the total Aroclor concentrations as measured by GC for samples from five different contaminated sites. ELISA-derived PCB-126 concentrations were higher than the sums of the 12 coplanar PCBs generated by GC/MS with a positive correlation (r=0.9441). Results indicate that the SPLE–ELISA approach can be used for quantitative or qualitative analysis of PCBs in soil and sediments. To our knowledge, this is the first report of an SPLE–ELISA approach not requiring a post-extraction cleanup step for detecting Aroclors and coplanar PCBs in soil and sediment.

A one-step extraction/clean-up method for determination of PCBs, PBDEs and HBCDs in environmental solid matrices

A selective pressurized liquid extraction (S-PLE) method was developed for rapid determination of 3 classes of halogenated organic contaminants in indoor dust, soil and sediment samples. The optimised method used 3 : 2 v/v n-hexane-dichloromethane for extraction of polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs) and hexabromocyclododecanes (HBCDs). Extraction was performed at 90 °C for 5 min followed by 4 min static time under 1500 psi. Good recoveries of target analytes were obtained after 3 extraction cycles. In-cell cleanup was performed using 10 g of 44% H2SO4 acid silica and 5 g of florisil (secondary fat retainer), while copper powder was used to remove elemental sulfur. The method was validated using NIST SRM2585 and SRM 1941b in addition to an in-house previously characterised soil sample. Measured concentrations of target compounds showed good agreement with the certified values with RSD < 20% indicating the good accuracy and precision of the S-PLE method. Clean extracts provided low noise levels resulting in low method detection limits (<0.03 ng g(-1)) and LOQs (<0.1 ng g(-1)). The method developed was applied successfully to real environmental samples and it provided various advantages over traditional methods including reduced solvent consumption and analysis time, minimal sample contamination and high sample throughput which can be beneficial for environmental monitoring programs dealing with large numbers of samples.

Miniaturized selective pressurized liquid extraction of polychlorinated biphenyls and polybrominated diphenyl ethers from feedstuffs

A new miniaturized pressurized liquid extraction (PLE) with in-cell purification method has been developed for the simultaneous extraction of endogenous prioritary and toxic polychlorinated biphenyls (PCBs) and environmentally relevant tri- to deca-brominated diphenyl ether (PBDE) congeners from different feed matrices. Parameters affecting the efficiency of the selective PLE process, such as sorbent:matrix ratio, volume and nature of the extraction solvent, PLE working mode, extraction time and temperature, and amount of co-sorbents, were optimized. n-Hexane and n-hexane:dichloromethane (1:1, v/v) were used as extraction solvents. 8-mL of organic solvents and 3.5g of sorbents sufficed for complete sample treatment. Only 0.25g of feed sample were required for accurate determination of the endogenous PCBs studied using gas chromatography with a micro-electron capture detector (GC-μECD) during method development, and for PBDE analysis using either GC-μECD or gas chromatography with negative chemical ionization-quadrupole mass spectrometry (GC–NCI-qMS). Gas chromatography coupled to ion trap detection working in tandem mode, GC-ITD (MS/MS), was used for final PCB confirmation. Additional purification of the sample extracts was not required. The performance of the complete PLE-based method was evaluated at two spiking levels, 0.4 and 4ng/g wet weight. Recoveries in the range 60–120% were obtained for PCBs, while those of PBDEs ranged from 86% to 114% for most of the target analytes. The relative standard deviations were in general lower than 20%. The optimized procedure was applied to the determination of the investigated PCBs and PBDEs in a variety of feed samples.

Optimization of selective pressurized liquid extraction for extraction and in-cell clean-up of PCDD/Fs in soils and sediments

This paper describes the development of methods for selective extraction of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) from soils and sediments, using pressurized liquid extraction with in-cell clean-up (SPLE). Two binary solvent mixtures, viz. dichloromethane/n-heptane (DCM/Hp), and diethylether/n-heptane (DEE/Hp), were evaluated. The SPLE extraction conditions were optimized using central composite face (CCF) design. Three factors were investigated: extraction temperature (60–160°C), number of extraction cycles (1–3) and time per cycle (2–18min). The results showed that DCM/Hp (1/1, v/v) and DEE/Hp (1/2, v/v) were the best extraction solvent compositions and that the extraction temperature was a critical factor that needed careful optimization to achieve high extraction efficiency without co-extraction of sulfuric acid. Under the optimal conditions, the SPLE methods provided results with good accuracy and precision. For the sandy soil certified reference material (CRM-529) the quantification results ended up in the range 82–110% as compared to the concentrations obtained by a reference method based on Soxhlet extraction and external column clean-up. Furthermore, for a clay soil (CRM-530) and a sediment reference material (WMS-01), the accuracy (trueness) of the TEQ values were +11% (DCM/Hp) and +8% (DEE/Hp) for CRM-530, +8% and −7% for WMS-01, respectively. The individual congener concentrations also agreed well with the certified values. These findings show that SPLE is a promising method for combined extraction and clean-up of PCDD/Fs in soil/sediment samples.

Fast and selective pressurized liquid extraction with simultaneous in cell clean up for the analysis of alkylphenols and bisphenol A in bivalve molluscs

A novel and green analytical methodology for the determination of alkylphenols (4-tert-octylphenol, 4-n-octylphenol, 4-n-nonylphenol, nonylphenol technical mixture) and bisphenol A in bivalve mollusc samples was developed and validated. The method was based on selective pressurized liquid extraction (SPLE) with a simultaneous in cell clean up combined with liquid chromatography–electrospray ionization tandem mass spectrometry in negative mode (LC–ESI-MS/MS). Quantitation was performed by standard addition curves in order to correct matrix effects. The analytical features of the method were satisfactory: relative recoveries varied between 80 and 107% and repeatability and intermediate precision were <20% for all compounds. Uncertainty assessment of measurement was estimated on the basis of an in-house validation according to EURACHEM/CITAC guide. Quantitation limits of the method (MQL) ranged between 0.34 (4-n-octylphenol) and 3.6ngg−1 dry weight (nonylphenol). The main advantages of the method are sensitivity, selectivity, automaticity, low volumes of solvents required and low sample analysis time (according with the principles of Green Chemistry). The method was applied to the analysis of mussel samples of Galicia coast (NW of Spain). Nonylphenol and 4-tert-octylphenol were measured in all samples at concentrations between 9.3 and 372ngg−1dw. As an approach, the human daily intake of these compounds was estimated and no risk for human health was found.

Development of an analytical methodology for the determination of the antiparasitic drug toltrazuril and its two metabolites in surface water, soil and animal manure

This paper presents the development, optimization and validation of a LC–MS/MS methodology to determine the antiparasitic veterinary drug toltrazuril and its two main metabolites, toltrazuril sulfoxide and toltrazuril sulfone, in environmental surface water, soil and animal manure. Using solid phase extraction and selective pressurized liquid extraction with integrated clean-up, the analytical method allows for the determination of these compounds down to 0.06–0.13ngL−1 in water, 0.01–0.03ngg−1dw in soil and 0.22–0.51ngg−1dw in manure. The deuterated analog of toltrazuril was used as internal standard, and ensured method accuracy in the range 96–123% for water and 77–110% for soil samples. The developed method can also be applied to simultaneously determine steroid hormones in the solid samples. The antiparasitic drug and its metabolites were found in manure and soil up to 114 and 335pgg−1dw, respectively. Little is known regarding the environmental fate and effects of these compounds; consequently more research is urgently needed.

Selective pressurised liquid extraction of halogenated pesticides and polychlorinated biphenyls from pine needles

Pine needles are an ideal matrix for the long-term monitoring of semi-volatile organic compounds in the atmosphere because they are naturally occurring and distributed worldwide. However, typical extraction methods result in the co-elution of matrix-interfering compounds and thus require time-consuming clean-up steps. A selective pressurised liquid extraction method (S-PLE) for extracting current-use pesticides, historic-use pesticides and polychlorinated biphenyls (PCBs) from pine needles that does not require additional clean-up steps was developed and validated. The selective extraction was achieved by packing the extraction vessel with a fat retainer, Florisil, down-stream of the pine needle matrix. A fat to fat-retainer ratio of 0.0057 (corresponding to 35g of Florisil per 10g of pine needle sample) was selected to minimise the co-elution of matrix-interfering compounds. Three 5-min extractions were performed using 25:75 (v/v) dichloromethane:n-hexane and a solvent flush of 150%. The mean recovery of spiked current-use pesticides, historic-use pesticides and PCBs using this method was 71%, 72%, and 84%, respectively. The method was validated by comparing target analyte concentrations measured in a pine needle sample using the optimised S-PLE method to those obtained using a conventional PLE method with external clean-up. The method detection limits and reproducibility were similar for the two methods; however, sample preparation time was 67% shorter when using the S-PLE method.

Development of a simultaneous extraction and cleanup method for pyrethroid pesticides from indoor house dust samples

An efficient and reliable analytical method was developed for the sensitive and selective quantification of pyrethroid pesticides (PYRs) in house dust samples. The method is based on selective pressurized liquid extraction (SPLE) of the dust-bound PYRs into dichloromethane (DCM) with analysis by gas chromatography/mass spectrometry. Various adsorbents and combinations of extraction solvents and temperatures were evaluated to achieve a high-throughput sample preparation that eliminates the post-extraction cleanup step. The final method used sulfuric acid-impregnated silica (acid silica) and neutral silica together in the extraction cell with the dust sample to provide both extraction and cleanup simultaneously. The optimal ratio of dust/acid silica/silica was 1:0.8:8. The extraction was performed at 2000psi, at 100°C with DCM for 5min in three cycles. Method precision and accuracy were evaluated by the analysis of triplicate aliquots of the dust samples and the samples fortified with the target PYRs. The accuracy measured as the recoveries of the PYRs in the fortified samples ranged from 85% to 120%. The precision measured as the relative standard deviation of replicate samples was within ±25%. The SPLE method was applied to 20 house dust samples collected from households that participated in two field studies regarding exposures to pesticides and other pollutants. Similar concentrations of target PYRs were obtained for the SPLE and a stepwise extraction/cleanup procedure. The SPLE procedure reduces organic solvent consumption and increases the sample throughput when compared with a traditional stepwise extraction and cleanup procedure. This study demonstrates that the SPLE procedure can be applied to complex dust matrices for analysis of PYRs for large scale exposure or environmental monitoring studies.

Rapid determination of pesticide residues in herbs using selective pressurized liquid extraction and fast gas chromatography coupled with mass spectrometry

A selective pressurized liquid extraction and gas chromatography coupled with triple quadrupole mass spectrometer method was developed for simultaneous determination of 52 pesticide residues in medicine and food dual-purpose herbs. The developed extraction method integrated extraction and cleanup processes for sample preparation. The sorbents, 5 g Florisil and 100 mg graphitized carbon black, were placed inside the extraction cell to remove matrix interferences. Optimized conditions of selective pressurized liquid extraction were ethyl acetate as extraction solvent, 120°C of extraction temperature, 6 min of static extraction time, 50% of flush volume extracted for two cycles. An ultra inert capillary GC-MS HP-5 UI column (20 m × 0.18 mm id, 0.18 μm) and column backflush system were used for the analysis. Multiple-reaction monitoring was employed for the quantitative analysis with electron ionization mode. All calibration curves showed good linearity (r(2) > 0.995) within the test ranges. The average recoveries of most pesticides were from 81 to 118%. The validated method was successfully applied for the determination of pesticide residues in four herbs. The results indicate that selective pressurized liquid extraction and GC-MS/MS is a sensitive and reliable analytical method for the simultaneous determination of multiple pesticide residues in herbs.

In-Cell Clean-Up Pressurised Liquid Extraction Method to Determine Pesticides in Mushroom Compost by Gas Chromatography-Tandem Mass Spectrometry

A fast, simple, and easily automated method for the determination of two insecticides, diazinon and deltamethrin, and two fungicides, iprodione and prochloraz, in mushroom cultivation compost samples, based on selective pressurised liquid extraction (SPLE) and gas chromatography coupled to tandem mass spectrometry, is presented. The proposed method integrates extraction and clean-up processes in one single step, by adding a clean-up sorbent into the extraction cell. SPLE variables were thoroughly studied by experimental design. First, different clean-up sorbents and extraction solvents were screened at two temperature levels using a multifactor design; resulting Florisil and 1 : 1 acetone-dichloromethane the best combination. Then, temperature, extraction time, and sample-sorbent mass ratio were optimized by a central composite design. Best recoveries were obtained with a 0.4 sample-sorbent ratio, at 105°C and a 2 min extraction time. The SPLE method was characterized in terms of recovery (with values ranging from 81 to 103%), repeatability and intermediate precision (showing relative standard deviations less than 12% in most cases), and sensitivity (providing detection limits between 0.1 and 6 ng mL–1). However, in spite of the clean-up process a matrix effect was observed and therefore standard addition calibration was recommended.

Determination of polycyclic aromatic hydrocarbons from soil samples using selective pressurized liquid extraction

A selective pressurized liquid extraction (SPLE) method has been optimized for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil samples. The method comprises a fully automated extraction and on-line clean-up procedure by inclusion of sorbents in the extraction cells. The contributing parameters of SPLE including type of solvent, static extraction time, number of extractions, extraction temperature, nature and amount of sorbents were investigated. The optimal extraction was performed at 70 °C for 10 min (static extraction time) cycled once using n-hexane/methylene chloride (50 : 50, v/v) and the sorbents in the extraction cells were 3 g of alumina and 2 g of silica gel. The collected extracts from the cells, after pre-concentration, were clean enough for direct injection into GC-MS. Validation of the SPLE technique was performed, with the recovery rates for 16 PAHs in the range of 75–103%, and the relative standard deviation (RSD) was generally less than 10%. Method detection limits (MDL) were in the ranges of 0.001–0.080 μg kg−1 for the GC-MS analyses. Finally, the method was successfully used to evaluate the cultivated soils in Beijing, China.

Focused ultrasound solid–liquid extraction and selective pressurised liquid extraction to determine bisphenol A and alkylphenols in sewage sludge by gas chromatography–mass spectrometry

A new method for determining endocrine disrupter compounds (EDCs) in sewage sludge is described in this paper. EDCs studied were bisphenol A (BPA) and alkylphenols (APs). In order to obtain a fast and simple method, selective pressurised liquid extraction (SPLE) and focused ultrasound solid-liquid extraction (FUSLE) were tested. Best results for SPLE were obtained using Florisil as clean-up sorbent and dichloromethane as extraction solvent, while temperature was the only significant variable. Analyte extraction by SPLE was completed in only one extraction cycle of 1 min at 130 °C. FUSLE was carried out in one step of 20 s at 75% power (0.5 cycles) and with 8 mL of ethyl acetate. Although the optimised FUSLE process was faster, simpler and cheaper, SPLE provided higher recovery values (ranging from 81 to 105%) and therefore SPLE-based method was selected and validated. The SPLE and GC-MS method showed an LOD of 10.7 ng/g for BPA and LODs between 1.2 and 41.6 ng/g for APs. Relative standard deviation values lower than 6% were obtained for all analytes. As a result, an efficient, fast and simple method based on SPLE and GC-MS for the determination of BPA and APs in sewage sludge is proposed.

Selective pressurized liquid extraction of three classes of halogenated contaminants in fish

Pressurized liquid extraction (PLE) combined with in-cell clean-up of co-extracts, so-called selective-PLE (S-PLE), is a fast and accepted method for the analysis of halogenated organic contaminants in fish. However, many of the existing methods were optimized for use with single classes of contaminants. The main objective of this research was to develop an S-PLE method that elutes a minimal amount of fats while simultaneously extracting halogenated pesticides, polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs) from fat-rich fish. The optimized method uses n-hexane:dichloromethane (75:25, v/v) as the extraction solvent, a 0.0078 fat to fat-retainer ratio (FFR) with Florisil as the fat retainer, three individual 5-min extractions with flush volumes of 150% and a selection of labeled surrogate standards (isotope dilution). This method resulted in a mean recovery of 77% for all target analytes in spiked samples and an average relative standard deviation of 6.3%. The method was validated with a certified reference material; the mean measured analyte concentrations agreed with the reference values except in the case of individual endosulfan isomers. It is likely that interconversion from the beta- to alpha-endosulfan isomer had occurred in the CRM, resulting in low measured concentrations for beta-endosulfan and high measured concentrations for alpha-endosulfan when compared with the reference values. Finally, the method was tested on three fish species with varying fat content. Different contaminant patterns were observed in the various species.

Simultaneous extraction and clean-up of polybrominated diphenyl ethers and polychlorinated biphenyls from sheep liver tissue by selective pressurized liquid extraction and analysis by gas chromatography–mass spectrometry

We describe a selective pressurized liquid extraction (SPLE) method, followed by gas chromatography–mass spectrometry (GC–MS), for the simultaneous extraction and clean-up of polybrominated diphenyl ethers (PBDEs) and polychlorinated biphenyls (PCBs) in sheep liver tissue samples. The on-line clean-up of liver tissue by SPLE was tested using differing amount of acid-modified silica (sulphuric acid:silica gel, 1:2, w/w), the most effective amount being 20 g. Different extraction solvents (iso-hexane and dichloromethane), either alone or in various combinations, were used to extract these target compounds from spiked liver samples. Variables affecting the SPLE extraction efficiency, including temperature, pressure, number of extraction cycles and static extraction time were studied; the optimum parameters were 80 °C, 10.3 MPa, 2 cycles and 5 min, respectively. The SPLE based method was compared with more traditional Soxhlet, off-line PLE, ultrasonic and heating extraction methods. Overall the mean percentage recoveries for all target chemicals using SPLE were 86–103% ( n = 3, SD < 9%), and compared favourably with the Soxhlet (63–109%, n = 3, SD < 8%), off-line PLE (82–104%, n = 3, SD < 18%), ultrasonic (86–99%, n = 3, SD < 11%) and heating (72–102%, n = 3, SD < 21%) extraction methods. The limits of detection of the proposed method were 5–96 pg g −1 and 2–29 pg g −1 for the different PBDE and PCB chemicals studied, respectively. The outputs of the proposed method were linear over the range from 0.02 to 30 ng g −1, for all PCB and PBDE congeners except for PBDE 100 and 153 (0.05–30 ng g −1) and PBDE 183 (0.1–30 ng g −1). The method was successfully applied to sheep liver samples for the determination of the target PBDE and PCB compounds.

Selective pressurized liquid extraction of estrogenic compounds in soil and analysis by gas chromatography–mass spectrometry

A selective pressurized liquid extraction (SPLE) method, followed by gas chromatography–mass spectrometry (GC–MS), for the simultaneous extraction and clean-up of estrone (E1), 17β-estradiol (E2), 17α-ethynylestradiol (EE2), estriol (E3) and bisphenol A (BPA) from soil samples is described. The on-line clean-up of soil by SPLE was achieved using different organic matter retainers, including silica, alumina and Florisil, the most effective being silica. Thus, different amounts of silica, in conjunction with different extraction solvents (acetone, ethyl acetate, isohexane and dichloromethane), either alone or in combination, were used to extract the target chemicals from spiked soil samples. It was shown that 3 g silica resulted in satisfactory rates of recovery of target compounds and acetone:dichloromethane (1:3, v/v) was efficient in extracting and eluting estrogenic compounds for SPLE. Variables affecting the SPLE efficiency, including temperature and pressure were studied; the optimum parameters were 60 °C and 1500 psi, respectively. The limits of detection (LODs) of the proposed method were 0.02–0.37 ng g −1 for the different estrogenic chemicals studied. The outputs using the proposed method were linear over the range from 0.1 to 120 ng g −1 for E1, E2, EE2, 0.2–120 ng g −1 for E3, and 0.5–120 ng g −1 for BPA. The optimized method was further verified by performing spiking experiments in natural soil matrices; good rates of recovery and reproducibility were achieved for all selected compounds and the method was successfully applied to soil samples from Northeast Scotland, for the determination of the target compounds.

Suitability of selective pressurized liquid extraction combined with gas chromatography–ion-trap tandem mass spectrometry for the analysis of polybrominated diphenyl ethers

A one-step extraction and clean-up method using pressurized liquid extraction (PLE) (selective PLE) combined with gas chromatography–ion-trap tandem mass spectrometry (GC–ITMS–MS) was evaluated for the analysis of polybrominated diphenyl ethers (from tri- to hepta-PBDEs) at low concentrations in fish and shellfish samples. To this end, the performance of an on-line PLE extraction/clean-up method and of a classical Soxhlet extraction and clean-up method using a multi-layer modified silica column were compared. The two sample treatment methods provided similar results, although an important reduction in the sample treatment time (40 min per sample) was achieved using the selective PLE method. In addition, the suitability of the PLE combined with GC–ITMS–MS method was evaluated by comparing the results obtained in the analysis of fish samples with those obtained by gas chromatography–high resolution mass spectrometry (GC–HRMS). Good agreement between both techniques was obtained with differences between the mean values of less than 16%. The selective PLE method coupled to GC–ITMS–MS produced accurate results for PBDE determination with low limits of detection (1.0–16.8 pg g −1 wet weight) and quantification (3.1–51 pg g −1 wet weight) as well as good precision (RSD < 16%). This method has been applied to the analysis of PBDEs in fish and shellfish samples collected at fish markets in Catalonia (NE Spain).

Fast Analysis of Polybrominated Diphenyl Ethers in Eggs Using Selective Pressurized Liquid Extraction Coupled with Online GPC-GC/MS

This article reports the applicability of online gel permeation chromatography (GPC)-GC/MS for the determination of seven predominant polybrominated diphenyl ethers (PBDEs) in eggs to effectively eliminate matrix interference. Selective pressurized liquid extraction using acidic alumina as a fat retainer was used for cleanup of the PBDEs in eggs. It was selected because of its advantages: simpler operation, minimum time spent on sample handing to get fat-free extracts, and low volume of solvent consumption. After concentration, the extract was directly injected for online GC/MS operated in the negative ion chemical ionization mode with a 15 m capillary column. Recoveries of spiked samples were between 75.1 and 102.0%, with RSDs (n=3) ranging from 3.69-11.47% when spiked at levels of 2 and 20 ng/g, dry mass. The LOD varied from 0.25-34 ng/g, dry mass. The proposed method was proven to be rapid, efficient, and reliable for the trace determination of PBDEs in eggs.