Scanning Electron Microscopy Images Research Articles

Effects of Acid Etching on the Microstructure and Stiffness of Human Teeth

Abstract The mechanical properties of acid-etched enamel and dentin are important for understanding tooth erosion and developing innovative dental restorative materials. In this study, the microstructure and mechanical properties of both enamel and dentin were characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM) to quantify the impact of acid etching. SEM images demonstrated that enamel rods have a diameter of approximately 5 μm, while dentinal tubules have a diameter of around 2 μm. After acid etching, the intertubular and peritubular regions were exposed, with the peritubular regions showing a thickness of approximately 1 μm. AFM measurements showed that the stiffness of enamel at the bottom, middle, and top layers is 26.28±4.24 GPa, 32.03±8.68 GPa, and 23.94±3.53 GPa, respectively. For dentin, the stiffness is 16.28±2.76 GPa at the bottom layer and 17.59±5.33 GPa at the middle layer. AFM morphology and stiffness maps illustrated the microstructures of enamel rod and sheaths, as well as dentin tubules in both unetched and acid-etched tooth sections. The stiffness of the acid-etched enamel rod and peritubular dentin decreased by 7-fold and 3.6-fold, respectively, compared to the unetched enamel rod and peritubular dentin.

Applications of deep learning-based denoising methodologies for scanning electron microscope images

Abstract In this paper, we use five types of deep-learning algorithms for denoising scanning electron microscope (SEM) measurement data. Denoising of SEM images is an important task since the images often suffer from noise, which can make it difficult to accurately interpret the data. We also investigate realistic SEM denoising characteristics using a variety of metrics to assess the quality of denoised images. Overall, we find that the trained generative models provide superior denoising performance and that it is crucial to objectively quantify the performance, just like in the scanning process itself. It is anticipated that the deep-learning based technique can accelerate image measurements, which can be utilized for very fast analytical investigations. We also demonstrate that the success of a generative model may depend on the appropriate assessment of noise characteristics in the specific image data analysis of interest. Moreover, it is addressed that denoising performance can be properly evaluated when a relevant metrics that aligns well with human visual systems.

A highly sensitive and selective ZnO-based ammonia sensor: Fe- doping effect

Abstract This study investigates the gas sensing capabilities of ZnO and Fe-doped ZnO films prepared via a cost-effective spin coating method. The films were characterized optically, structurally, and morphologically. X-ray diffraction revealed good crystal quality with a polycrystalline nature, and wurzite structure, though crystal quality and crystallite size decreased with Fe doping. Optical measurements indicated an increased optical band gap from 3.205 ± 0.002 to 3.220 ± 0.002 eV after Fe doping. Scanning electron microscope images confirmed spherical grainy structures with reduced grain sizes after Fe doping. Gas sensing measurements at room temperature (RT) at an exposure of vapors of various toxic chemicals (acetone, ethanol, propanol, methanol, and ammonia), demonstrated a highly selective nature of ZnO and Fe-ZnO towards the ammonia. The Fe-doping into ZnO improved the ammonia sensing capability of ZnO film. The Fe-ZnO film exhibited a gas response of 388.8 ± 5.5 at 400 ppm ammonia exposure, which was nearly 10 times larger than that of ZnO film with a response/recovery time of 22/51 s, good stability, and good repeatability. The Fe-ZnO film’s higher response is attributed to its smaller grain sizes and surplus of charge carriers after Fe doping which promote the adsorption of extra oxygen ions onto the film’s surface and the subsequent interaction between the adsorbed oxygen ions ammonia molecules. It could detect up to the lower limit of 1 ppm ammonia with a response of 24.2 ± 0.9, which is better than the previous reports. These results reveal the Fe-ZnO film as a viable material for developing a cost-effective and efficient ammonia sensor at room temperature.

Enhanced wound healing with biogenic zinc oxide nanoparticle-incorporated carboxymethyl cellulose/polyvinylpyrrolidone nanocomposite hydrogels.

Contemporary wound dressings lack antibacterial properties, exhibit a low water vapour transmission rate, and demonstrate inadequate porosity. In order to overcome these limitations, scientists have employed water hyacinth to produce carboxymethyl cellulose (CMC). CMC/PVP nanocomposite films containing biogenic zinc oxide nanoparticles (nZnOs) were synthesised using cost effective solution-casting technique. As the proportion of nZnOs in the film increased, swelling and water permeability decreased, whereas mechanical stability improved. Dynamic light scattering testing and transmission electron microscopy confirmed that the particle size was around 50.7 nm. Field emission scanning electron microscopy (FESEM) images showed that nZnOs were distributed uniformly in the polymer matrix. Cell viability against Vero cells was greater than 94%, and a substantial zone of inhibition against S. aureus and E. coli bacteria was observed. Wounds of albino mice were treated with CMC/PVP and CMC/PVP/nZnO (6%) nanocomposite hydrogels and healed in 20 and 12 days, respectively, as demonstrated by wound healing assay and histological staining. In vitro and in vivo studies revealed that the novel nanocomposite hydrogels exhibit improved cell viability and wound healing features. Therefore, they could be exploited as promising skin wound dressing materials.

From two segments and beyond: Investigating the onset of regeneration in Syllis malaquini.

Annelids feature a diverse range of regenerative abilities, but complete whole-body regeneration is less common, particularly in the context of the head and anterior body regeneration. This study provides a detailed morphological description of Syllis malaquini regenerative abilities. By replicating previous experiments and performing diverse surgical procedures, we explored the capacity of this species for whole-body regeneration. We detailed the precise timing of regeneration of particular structures such as the eyes, proventricle, pharyngeal tooth, nuchal organs, and body pigmentation after amputation. Our high-resolution scanning electron microscopy and confocal laser-scanning microscopy images provide details of the blastema region, revealing that while anal opening remains in connection to the exterior environment, oral opening is formed "de novo" during blastema differentiation. Additionally, we performed amputations to isolate fragments consisting of one, two, and three segments from the intestinal trunk region. We found that S. malaquini requires at least two to three segments to successfully regenerate the whole body. In addition, we verified a variable capacity to regenerate depending upon the gut region, with structures of the foregut greatly impairing some steps of the regenerative process. Our work notably addresses the gap in knowledge concerning gut formation and its impact on regenerative capabilities. Ongoing research is crucial to unravel the role of gut tissue specificity and plasticity during regeneration in annelids, and particularly in syllids.

Anodized SLM Ti6Al4V surfaces: influence of surface characteristics on NTs growth and resulted surfaces properties.

TiO2 nanotubes (NTs) obtained via electrochemical anodization (EA) on conventionally machined titanium surfaces are reported to be promising for achieving mucointegration in dental implant therapy. Dental abutments, manufactured by selective laser melting (SLM), combined with thermal post-treatment, present a promising alternative to conventionally machined titanium. Based on an original protocol, this study aims to investigate how the characteristic microstructure of the α + β phases in post-heated SLM Ti6Al4V can influence the growth of NTs and the resulting physical and chemical surface properties. Ti6Al4V-SLM discs were fabricated, heat post-treated and mechanically polished. The samples were then subjected to EA under different voltage conditions (10, 20 and 30 V). The specimens' surfaces were characterized at the same location, before NTs formation by electron backscatter diffraction (EBSD), and after by scanning electron microscopy (SEM). Then, roughness and wettability were studied to determine how EA affects surface properties compared to conventionally machined and polished titanium surfaces without NTs (reference). Surface reactivity was evaluated through chemical analysis and collagen binding capacities. The self-organized TiO2 layer was developed on the α phase only and the β phase was preferentially dissolved. The characteristic dimensions of the nanotubes (diameter, length and wall thickness), measured by SEM image analysis, increased proportionally with the rise in voltage but were not affected by the crystallographic orientation of the underlying α grain. Micro-roughness was the same for nanotubular and reference surfaces. Wettability was improved, as was surface reactivity towards collagen, which may contribute to improved bioactivity of titanium surfaces in dentistry.

Development and Performance of a PANI@NiMnO3 Nanocomposite for Enhanced Supercapacitors and Photocatalytic Applications.

Conductive polymers are gaining considerable attention as a potential material for supercapacitor electrodes due to their favorable properties. Among these, polyaniline (PANI) stands out as a cost-effective and easy to synthesize, making it a promising candidate for improving energy storage applications. This study presents the synthesis of a hybrid composite consisting of PANI and NiMnO3 (NMO) perovskite using the chemical oxidative polymerization method. The morphology and structure of the composite were analyzed by using scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. XRD results showed that the addition of NMO transformed the amorphous structure of PANI into a semicrystalline form, leading to enhanced conductivity. SEM images revealed a more uniform and compact structure, with NMO distributed unevenly within the polymer matrix. Optical analysis indicated that a reduction in the band gap of PANI@NMO reached 2.5 eV. N2 adsorption-desorption measurements confirmed an increase in the surface area and pore volume. The photocatalytic activity of the PANI@NMO nanocomposite was tested by degrading methylene blue (MB) dye under UV/visible light. The nanocomposite showed high efficiency, degrading 87.75% of MB dye after 125 min of irradiation as compared to their counter parts. Additionally, electrochemical tests demonstrated an improved electrochemical performance of the composite due to enhanced crystallinity, increased surface area, and reduced electron-hole recombination rate. These results suggest that the PANI@NMO nanocomposite has great potential for use in supercapacitors and photocatalysis.

Antibacterial Efficacy of Tryptophan Coordinated Silver Nanoparticles Against E. coli: Spectroscopic and Microscopic Evaluation of Bacterial Cell Death.

The capability of conventional fluorescence spectroscopy and right-angled synchronous fluorescence spectroscopy (SFS) was evaluated to quantify the antibacterial potential of chemically synthesized Tryptophan coordinated silver nanoparticles (Ag-TrpNPs). Silver nanoparticles have gained significant importance as a material of interest due to their diverse assemblies in the nanoscale range and their potent antibacterial activity. But due to toxicity of silver nanoparticles there is a dire need to coordinate these materials with some biocompatible and biodegradable molecules. The study has been focused on chemical synthesis of functional fluorescence nanomaterials based on Tryptophan molecules coordinated with silver nanoparticles (Ag-TrpNPs). The antibacterial activity of Ag-TrpNPs was assessed in bacteria due to their functional characteristics such as tuneability, biocompatibility, and bioavailability. We employed optical characterization techniques such as Ultraviolet-visible spectroscopy, dynamic light scattering (DLS), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), fluorescence spectroscopy, and confocal microscopy to ensure the particles formation in aqueous suspension. DLS analysis confirmed the hydrodynamic size of the nanoparticles of approximately 100nm. SEM images revealed the spherical morphology and size distribution of the Ag-TrpNPs. Escherichia coli bacterial strains were used to assess the antibacterial efficacy of the Ag-TrpNPs using fluorescence spectroscopy and imaging. Initially, the agar well plate method was employed to evaluate the antimicrobial activity of the Ag-TrpNPs. The significant zones of inhibition of size 37mm at 500µg/mL and 27mm at 15.5µg/mL were reported which indicated the efficiency of Ag-TrpNPs from higher to lower concentration. Conventional and synchronous fluorescence spectra provided evidence of bacterial cell death in aqueous suspensions to ensure the interaction of Ag-TrpNPs with E. coli bacteria at different times and concentrations. SEM was employed to investigate the interaction mechanism between Ag-TrpNPs and bacterial cells. The images revealed cell wall disintegration, leading to the leakage of cellular contents, and eventually cell death occurred.

Procedure for Fabrication and Characterization of Van-der-Waals Heterostructures

In this work we provide a step-by-step description of the technique for manufacturing various van der Waals heterostructures. First, we discuss the procedure to obtain monolayer and few-layer flakes from layered materials, in particular from graphite and hexagonal boron nitride. Next, we consider different approaches to the assembly depending on the required final device. Further, we describe in detail the procedure for making ohmic contacts and give the parameters for plasma chemistry and metal deposition. We observe the field effect in transport measurements but a number of features – a strong shift of the charge neutral point from the zero-gate voltage, a large resistance away from the charge neutral point, and low mobility – indicate a problem with the quality of the resulting devices. Nevertheless, one of the fabricated devices demonstrates reasonable quality – the maximum mobility is estimated at 15000 cm2V–1s–1, the magnetic field dependences demonstrate the quantum Hall effect, which is standard for high-quality graphene. Unexpectedly, scanning electron microscope images of the resulting devices reveal a large amount of contamination on the surface of the flakes, which may explain the corresponding quality of our devices. Preliminary results of flakes cleaning with chemical compounds and thermal treatment are given.

Influence of multiple friction stir welding passes on the microstructure and mechanical properties of AA2024 age-hardened aluminum alloy

Friction stir welding (FSW) is a promising joining process for age-hardened aluminum alloys. However, when the process is used for welding age-hardened aluminum alloys, the hardness and joint efficiency are poor mainly because the strengthening precipitates become incoherent and/or get dissolved during the welding process. In this novel work, efforts have been made to enable the reprecipitation of the strengthening precipitates using multi-pass FSW. After producing FSW welds on AA2024 alloy, the welds have been processed by the same tool and at the same parameters several times to facilitate the reprecipitation of strengthening precipitates. As the precipitation kinetics of age-hardened aluminum alloys are temperature-dependent, a thermal imaging camera was utilized to record the temperature history during welding and subsequent cooling of the welded plates. The metallurgical examination of welded samples was carried out using optical microscopy, Scanning Electron Microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and microhardness test. It was observed that grain refinement occurs continuously due to dynamic recrystallization and severe plastic deformation up to the third FSW pass, after which there is no significant change in grain size. Generally, the microhardness value was higher in the stir zone than the heat-affected zone (HAZ), and the hardness in the stir zone increased after 4 passes of FSW. SEM images show clusters of incoherent precipitates, fragmentation, precipitate dispersion, dissolution, and reprecipitation of precipitates during each subsequent pass. The identification of the precipitates was carried out using EDS and XRD analysis.

Hydrothermal Synthesis of ZnO Nanoflowers: Exploring the Relationship between Morphology, Defects, and Photocatalytic Activity

Two forms of flower-like ZnO nanostructures were synthesized using hydrothermal methods at various growth times/temperatures and zinc precursors. The morphology, structure, chemical composition, and optical properties of these ZnO nanoflowers were studied using a scanning electron microscope (SEM), X-ray diffraction spectroscopy (XRD), X-ray photoelectrons spectroscopy (XPS), Raman spectroscopy, and UV–Vis spectroscopy. The SEM images revealed two forms of flower-like nanostructures, namely lotus- and tulip-like flower ZnO nanostructures. The XPS analysis revealed the oxidation state of the Zn and O elements, as well as the presence of OH groups on the surface of the lotus-like flower ZnO nanostructure. The XRD results revealed less crystallinity of the lotus-like ZnO nanoflowers (NFs) compared with the tulip-like ZnO NFs. The XRD results revealed the presence of Zn (OH)2 in the ZnO NFs. The Raman results confirmed less crystallinity of the lotus-like ZnO NFs. The estimated optical bandgap was 2.92 and 3.0 eV for the tulip- and lotus-like ZnO NFs, respectively. The tulip-like ZnO NFs showed superior photocatalytic degradation of methylene blue dye, verified via UV–Vis radiation, compared with the lotus-like ZnO NFs, which show the impact of the structure defects and OH- impurities on the photocatalytic performance of ZnO nanoflowers.

Photosensitizer conjugated carbon dots@dopamine-copper sulfide nanocomposites: Advanced photoactive agents for antibacterial applications through experimental and theoretical insights

The massive use and abuse of antibiotics has given birth to drug-resistant bacteria and emergence of severe bacterial infections in people. Intriguingly, light activated antimicrobial activity i.e. antimicrobial photodynamic therapy has gained enhanced therapeutic potential and efficacy in killing the bacterial cells. Therefore, the present study investigates the efficacy of employing advanced nanocomposites for biocidal inhibition of bacterial growth through enhanced sterilization capabilities. Specifically, dopamine functionalized CuS NPs combined with carbon dots (CDs@Dop-CuS) were selected for their remarkable photodynamic potential when used in conjunction with methylene blue (MB). Comparative and synergistic application of Dop-CuS, CDs, and MB revealed the superior singlet oxygen generation potency of MB/CDs@Dop-CuS. Furthermore, the structural changes in the E. coli bacterial cells membrane were elucidated through scanning electron microscopy imaging, demonstrating superior inhibition rates of MB/CDs@Dop-CuS compared to MB alone under 660 nm irradiation. The commendable docking score and binding potential of CDs@Dop-CuS nanocomposites obtained via molecular docking simulations further validate their efficacy as photosensitizers against E. coli bacterial cells. Thus, this novel MB/CDs@Dop-CuS photosensitizer provides enhanced efficacy as an alternative to traditional antibiotic treatments, offering a superior disinfection for public utility services and addressing the growing issue of drug-resistant bacterial infections.

Hydrogen Bond Integration in Potato Microstructure: Effects of Water Removal, Thermal Treatment, and Cooking Techniques

Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and Scanning electron microscopy (SEM) were used to study the effects of heat treatments and water removal by freeze-drying after different time intervals (6, 12, 24, 48, and 72 h) on the molecular structure of potato tubers. SEM images show structural differences between raw (RP), microwaved (MP), and boiled potato (BP). MP showed a cracked structure. BP was able to re-associate into a granule-like structure after 6 h of freeze-dying, whereas RP had dried granules within a porous matrix after 24 h of freeze-drying. These results are consistent with the moisture content and FTIR results for MP and BP, which demonstrated dried spectra after 6 h of freeze-drying and relatively coincided with RP results after 24 h of freeze-drying. Additionally, three types of hydrogen bonds have been characterized between water and starch, and the prevalence of water very weakly bound to starch has also been detected. The relative crystallinity (RC) was increased by thermal treatment, whereby microwaving recorded the highest value. A comparison of the FTIR and XRD results indicated that freeze-drying treatment overcomes heat effects to generate an integral starch molecule.

Synthesis, crystal structure, characterization and corrosion inhibition studies of a strontium coordination polymer with tartaric acid

The reaction of anhydrous strontium chloride with the proton transfer compound 1-H-Imidazolium Hydrogen- meso-tartrate in water resulted in the formation of polymeric tartrate complex of strontium which is characterised by SXRD, IR, UV-Visible and TG/DTG analyses. The single crystal X-ray diffraction analysis reveals that each strontium atom is eight coordinate with distorted dodecahedral arrangement. The two metal fragments are linked through central four-membered Sr2O2 ring and there is no imidazole moiety in the complex. The compound displays a rare crystallographic feature where a shared hydrogen atom is located between two carboxylic groups. This unusual arrangement of hydrogen atom with an occupancy factor 0.5, located in between two carboxylate groups balances the total charge of the structure. FT- IR study reveals the bidentate coordination mode of the ligand. The thermal behaviour of the compound was studied using TG/DTG analysis. Corrosion inhibition property of the title compound on mild steel in 1.0M HCl has been investigated using weight loss method. The formation of protective film on the mild steel surface is confirmed by Scanning Electron Microscopy images. The inhibition efficiency increases with increase in concentration of inhibitor.

3D printed polymers for transseptal puncture simulation

PurposeThis study aims to examine the efficacy of 3D printing polymers to realistically mimic the fossa ovalis (FO) – a cardiac structure that is positioned in the interatrial septum – for simulating transseptal puncture (TP) procedures.Design/methodology/approachSpecimen of different materials and thicknesses were prepared and tested simulating the puncturing of the FO using a 12F ID/14F OD TP catheter. Force and tenting length results were compared with literature references. Scanning electron microscope images of the specimen were acquired to observe the perforated region as well as the structure of the specimen in the unaffected area.FindingsSignificant changes in the properties of interest were registered for the same material on specimens tested at different moments after fabrication. Suturable vessel wall polyjet material offers the best characteristics to replicate FO anatomy and mimic its behavior to puncturing.Originality/valueThe originality of the work lies in the test of different commercial materials. Similar works are already present in literature but specifically designed materials are used. Demonstrating that off-the-shelf materials could be viable for FO specimens would simplify the design of realistic TP simulators in the future.

Effect of propolis added to single-bottle adhesives on water permeation through the hybrid layer.

Water treeing and water droplets are observed within adhesive layers and on the hybridized surface after bonding sound dentin using single-bottle etch-and-rinse adhesives, indicating permeability of the hybrid layer to water. The aim of this study was to assess the efficacy of dentin sealing by adhesives containing propolis by quantifying the area of water transudation from dentinal tubules after dentin hybridization. Brazilian red propolis was added to experimental adhesive and Single Bond (3M/ESPE) adhesive; experimental adhesive and Single Bond without propolis were used as controls. Under simulated pulp pressure, two layers of adhesive were applied to etched human dentin discs. Three minutes after light-curing, the hybridized dentin surface was replicated, and epoxy resin replicas were created to obtain scanning electron microscope images. Data were evaluated using ANOVA and Tukey's test. Single Bond containing propolis significantly decreased water permeation through the hybrid layer compared with the control group. Three minutes after polymerization, the experimental adhesive without propolis had formed a permeable hybrid layer. The addition of Brazilian red propolis significantly reduced surface water on hybridized dentin in a concentration-dependent manner. Two-step etch-and-rinse adhesives containing propolis were effective in reducing water permeation through the hybridized dentin surface.

Fatigue-thermal damage characteristics of red sandstone with a hole under high-temperature cyclic loading coupling and microstructural degradation

In underground coal gasification (UCG) projects, deeply buried subterranean projects are significantly influenced by high temperatures, alongside disruptive loads such as excavation, blasting, and drilling. Therefore, it is essential to study the fatigue behaviors of rocks under the coupled effects of thermal elevation and cyclic loads. This study performed uniaxial compression and cyclic loading-unloading tests on red sandstone specimens with cavities. The high-temperature fatigue behaviors of specimens were explored from various aspects, encompassing stress, deformation, energy, damage, and the microstructural variations of the specimens after high-temperature procedures were assessed by utilizing scanning electron microscopy (SEM). At temperatures below 600 °C, SEM images indicate a contraction of microcracks in the specimens, whereas temperatures above this threshold lead to their expansion. Notably, the total, elastic, and dissipated energy density of the specimens exhibit a curve of second degree with the upper limit stress. Additionally, elastic and dissipated energy densities linearly correlate with input energy density. Furthermore, the coupled damage and axial strain of the specimens positively correlate with the temperature. The damage mode of thermal fatigue is attributed to the accumulation and penetration of transgranular fractures within the red sandstone.

Exploring non-thermal plasma technology for microalgae removal

The global population and economic development surge has substantially increased water demand, resulting in heightened sewage and pollutant generation, posing environmental hazards. Addressing this challenge necessitates the implementation of efficient and cost-effective water reclamation methods. Non-thermal plasma technology (NTP) has emerged as a promising solution, garnering attention for its superior efficiency compared to alternatives. While existing studies have predominantly focused on energy efficiency and pollutant removal, limited research has delved into the biological removal aspect, particularly concerning algae. This study utilized a dielectric barrier plasma diffuser to eliminate Spirulina microalgae (Spirulina platensis) from wastewater solutions, demonstrating higher algae removal and superior mass transfer compared to alternative plasma methods. The effect of sample volume, input voltage and power, flow rate, and initial solution concentration on the algae removal was investigated. Investigation of operational parameters revealed the best condition resulting in a 98 % removal rate and 20 g/kWh energy efficiency. The best conditions for the removal of Spirulina microalgae were considered in a sample volume of 50 mL, a voltage of 7.6 kV, a flow rate of 700 mL/min, and an initial solution concentration of 1280 mg/liter. Scanning Electron Microscope (SEM) images illustrated the impact of active species on cell structure, leading to the destruction of spiral form and loss of reproductive ability. The study underscores the potential of NTP for efficient algae removal and identifies key active species involved in the process. The removal of Spirulina microalgae was attributed to a combination of singlet oxygen (1O2), hydroxyl radicals, and ozone.

Maleic anhydride esterified potato starch as the binder in silicon nanoparticles anode for lithium-ion batteries

Potato starch is a natural carbohydrate binder. Starch has hydroxyl groups that can promote interaction with silicon particles using multifaceted hydrogen bonds. Maleic anhydride esterified potato starch can produce a binder that maintains the cycle stability of lithium-ion batteries. Fourier-transform infrared spectroscopy spectra show wavelengths of 1776 cm−1 and 1855 cm−1. Thermal gravimetric analysis curves decreased in weight percent by 80 % at 286 °C. Carbon-13 nuclear magnetic resonance spectra show high peaks at 3.37 ppm, 3.65 ppm, 4.56 ppm, 5.09 ppm, and 6.22 ppm. Scanning electron microscope images show that the morphological change in esterified starch was due to the increased length of starch and the maleic anhydride grafted onto the starch granules. The cyclic voltammetry curve shows that the reduction peak is around 0.16 V, and the oxidation peak is around 0.38 V and 0.56 V. Nyquist plots show a small half circle, indicating that the electrode's solid-electrolyte interphase layer is low. The cycling performance shows a capacity of 1950 mAh/g.

Microbial Degradation of Polyester Microfibers Using Indigenously Isolated Bacterial Strain Exiguobacterium Sp.

ABSTRACTSynthetic microfibers are emerging environmental microplastic pollutants released from different industrial and domestic sources. The present investigation describes the isolation of potential bacterial strains from microplastic‐contaminated sites of Bhubaneswar city of Odisha, India. Four morphologically distinct bacterial strains were isolated using 2% polyethylene glycol (PEG) supplemented nutrient agar (NA) medium and were screened for their polymer tolerance ability by growing them on 2%–8% PEG. A single microorganism capable of growing on 8% PEG was selected for biodegradation experiment. Through 16S rRNA sequencing, the selected bacterial strain was identified as Exiguobacterium sp. with gene bank accession number ON318396. The microbial strain's microfiber biodegradation ability was assessed in a laboratory setting over a period of 28 ± 2 days, utilizing optimized conditions with an initial pH of 7, 2 mL inoculum volume, an incubation temperature of 30°C ± 2°C, and 150 rpm, using 2 g of polyester microfiber. In optimum conditions, the weight loss of the treated sample with the selected microbial strain was 19.2%. The polyester degradation was confirmed through scanning electron microscopic images viewing the degradation of the polyester microfiber surfaces. Variation in functional groups confirmed through Fourier transform infrared spectrophotometry. Detection of carbonyl (C═O) group stretching band at 1711 cm−1 through ATR‐FTIR analysis in the treated sample confirmed the polymer biodegradation. The potential isolate can efficiently degrade polyester and, in the future, can be employed as a promising solution for the sustainable treatment of synthetic microfiber pollution.