Scan Mode Research Articles

Comprehensive analysis of different types of ginsenosides in the different parts of American ginseng by targeted and nontargeted MS/MS scanning.

To comprehensively study the ginsenosides distribution in the various tissues of American ginseng, the qualitative and quantitative-targeted and nontargeted mass spectroscopic methods were established using the high-performance liquid chromatography coupled with Qtrap triple quadrupole mass spectrometry (HPLC-QtrapQQQ-MS). The total ginsenosides of the root, stem, and leaf of American ginseng were determined by a colorimetric method, and the contents showed the order from high to low root, stem, and leaf. Eighty-two kinds of ginsenosides were detected in the different parts of American ginseng by enhanced mass scan-information-dependent data acquisition (IDA)-enhanced product ion (EPI) scan mode, including 69 from the root, 62 from the stem, and 48 from the leaf. An HPLC-multiple reaction monitoring (MRM) method was established, and 28 representative ginsenosides were further quantified in the three parts. Nearly all ginsenosides had the highest contents in the root and the lowest content in the leaf. Three types of ginsenosides (protopanaxadiol [PPD]-, protopanaxatiol [PPT]-, and oleanolic acid [OA]-types) were analyzed by precursor ion-IDA-EPI and MRM-IDA-EPI scan modes. Root had the most abundant ginsenosides in PPD- and PPT-type ginsenosides. Meanwhile, the OA-type ginsenosides are significantly enriched in the stem and leaf of American ginseng. The results provided a supplement to the quality assessment of American ginseng. PRACTICAL APPLICATION: The distribution profile of ginsenosides in the parts of American ginseng is different. Except for the root, the stem, and leaf of American ginseng have the most abundant ginsenosides in oleanolic acid type. The results reported herein can help the manufacturers choose appropriate materials to extract the ginsenosides.

SRG/ART-XC Galactic Plane Survey near Galactic Longitude L 20◦ : Catalog of Sources

We present a catalog of sources detected by theMikhail Pavlinsky ART-XC telescope onboardthe SRG space observatory during the observations of the Galactic plane region near a longitude l 20◦(L20 field) in October 2019. The L20 field was observed four times in the scanning mode, which provideda uniform coverage of the sky region with a total area of 24 sq. deg with a median sensitivity of 8 ×10−13 erg s−1 cm−2 (at 50% detection completeness) in the 4–12 keV energy band. As a result, we havedetected 29 X-ray sources at a statistically significant level, 11 of which have not been detected previouslyby other X-ray observatories. Preliminary estimates show that four of themcan presumably be extragalacticin nature. We also show that the source SRGA J183220.1−103508 (CXOGSG J183220.8−103510) ismost likely a galaxy cluster containing a bright radio galaxy at redshift z 0.121.

Problems of Optimal Altitude Determination of Drones in Vertical Scanning Mode

This paper takes the UAV’s search for ship targets in the sea area as the background and uses the relationship between the probability of finding the target in the UAV’s radar imagery, the distance between the UAV and the target, and the UAV’s parameters, and according to the probability of the UAV finding a target based on multiple images. Taking the product of the discovery probability and the swept area as the index of search efficiency, the relationship between the probability of finding the target and the area of the swept sea area is balanced. The optimization model of the scanning sea area is established in the case of circular and rectangular to determine the optimal altitude of the UAV flights.

State of the Retina and Optic Nerve in 21-Day Head-Down Tilt Bed Rest

Studies in conditions of head-down tilt bed rest are widely used experiments which imitate redistribution of body fluids similar to the redistribution of fluid media in microgravity. To study the mechanism of development of spaceflight-associated neuro-ocular syndrome (SANS) in head-down tilt bed rest studies scientists have evaluated, among other things, participants’ visual system parameters. The main symptom of SANS is an edema of an optic disc and a retina. To date, the results describing the influence of head-down tilt bed rest on the visual system are ambiguous, which determines the relevance of further research. The aim of the study is to analyze retinal morphometry in the optic disc area and macular area in participants before and after 21-day head-down tilt bed rest. The study was performed using an optical coherence tomography with angiography function (Optovue RTVue XR Avanti System) before and after 21-days of head-down tilt bed rest. In 4 participants (8 eyes) (men, mean age ± standard deviation: 29.3 ± 3.9 years) the macular zone and optic disc area were evaluated according to standard scanning modes. To analyze the values obtained, we used mean tendency scores, mean comparison criteria, and graphical analysis. The results of the retinal thickness in the optic disc zone were consistent with those of other researchers, indicating a possible increase in retinal thickness, but our results did not reach the level of statistical significance. A statistically significant thickening of the retina in the macular zone was shown for the first time, but the increase is significantly less in amplitude than the thickening of the nerve fiber layer in the optic disc zone. Analysis of vascular density under head-down tilt bed rest conditions was performed for the first time both for the optic disc zone and the macula zone, but additional studies are required to obtain steady conclusions. For the first time, an increase in retinal thickness in the macula zone in participants of head-down tilt bed rest experiments was shown; for the optic disc zone, data consistent with the results of other researchers were obtained. For the first time, angiographic data were obtained for the macula and optic disk areas, but the obtained differences in vascular density did not reach the level of statistical significance.

Automatic Classification of C-SAM Voids for Root Cause Identification of Bonding Yield Degradation

Wafer-level direct bonding technology is a key process for the production of backside illuminated (BSI) CMOS image sensor (CIS). Usually, constant-depth mode scanning acoustic microscope (C-SAM) 300mm wafer images are acquired and defect size distribution is provided to monitor defects that degrade bonding yield. This acquisition technique is used as it is nondestructive and is able to capture the full wafer. Current solutions are not providing information detailed enough to identify the root cause of this degradation. A consequence is that most measurements and classification is currently done manually which take time and have reproducibility issues. In this paper, we propose a rule-based method for the classification of the defects and automatic segmentation of the defects to extract precise measurements depending on the type of defect. The classes of defects are precisely defined based on their origin in the process. All these information will allow to reduce the time to analyze the images and improve the precision and consistency of the analysis. These results will allow to identify more precisely the defects thus the causes of yield degradation during bonding process.

Sputter epitaxy and characterization of manganese-doped indium tin oxide films with different crystallographic orientations

Epitaxial Mn-doped indium tin oxide (ITO) films were deposited on single-crystal yttria stabilized zirconia (YSZ) substrates with (111), (110), and (100) crystal plane orientations using RF magnetron sputtering. The epitaxial relationship between the Mn-doped ITO films and the YSZ substrates was studied using x-ray diffraction (XRD) patterns in the ω–2θ scan mode and XRD pole figures. The Mn-doped ITO films on the YSZ(111) and YSZ(110) substrates exhibited a higher degree of crystallinity than the film on the YSZ(100) substrate as per the x-ray rocking curves. Fluctuations in the crystalline alignment were found to significantly influence the electrical properties of Mn-doped ITO films. Ferromagnetic hysteresis loops were observed at room temperature for all the epitaxial Mn-doped ITO films, irrespective of their crystallographic orientation. The magnetic properties of the epitaxial Mn-doped ITO films suggest that a combination of delocalized charge carrier-mediated interaction and bound magnetic polaron-driven interaction is required to explain the origin of ferromagnetism in these films. The Mn-doped ITO film on the YSZ(111) substrate exhibited the most desirable characteristics in terms of crystallinity, surface smoothness, electrical conductivity, and magnetic properties.

Detection and Analysis of Blood Dexmedetomidine in Drug-Facilitated Cases.

To establish a simple and rapid qualitative and quantitative detection method of dexmedetomidine in blood. Blood was separated on the Allure PFP Propyl liquid chromatography column with isocratic elution after it was precipitated by acetonitrile and filtered. Qualitative and quantitative analysis of dexmedetomidine was performed using positive ion scan mode and multi-reaction monitoring mode. The limit of detection of dexmedetomidine in blood was 0.2 ng/mL and the limit of quantification was 0.5 ng/mL. The linearity of the method was good in the range of 0.5-1 000 ng/mL, and the correlation coefficient was greater than 0.99. The accuracy of the method was 90.34%-112.67% and the extraction recovery was 50.05%-91.08%, with no significant matrix effect. This method is simple, selective and suitable for the qualitative and quantitative analysis of dexmedetomidine in blood, which can provide a reference for drug-facilitated cases involving dexmedetomidine.

TLS2trees: A scalable tree segmentation pipeline forTLSdata

AbstractAbove‐ground biomass (AGB) is an important metric used to quantify the mass of carbon stored in terrestrial ecosystems. For forests, this is routinely estimated at the plot scale (typically 1 ha) using inventory measurements and allometry. In recent years, terrestrial laser scanning (TLS) has appeared as a disruptive technology that can generate a more accurate assessment of tree and plot scale AGB; however, operationalising TLS methods has had to overcome a number of challenges. One such challenge is the segmentation of individual trees from plot level point clouds that are required to estimate woody volume, this is often done manually (e.g. with interactive point cloud editing software) and can be very time consuming.Here we presentTLS2trees, an automated processing pipeline and set of Python command line tools that aims to redress this processing bottleneck.TLS2treesconsists of existing and new methods and is specifically designed to be horizontally scalable. The processing pipeline is demonstrated on 7.5 ha of TLS data captured across 10 plots of seven forest types; from open savanna to dense tropical rainforest.A total of 10,557 trees are segmented withTLS2trees: these are compared to 1281 manually segmented trees. Results indicate thatTLS2treesperforms well, particularly for larger trees (i.e. the cohort of largest trees that comprise 50% of total plot volume), where plot‐wise tree volume bias is ±0.4 m3and %RMSE is 60%. Segmentation performance decreases for smaller trees, for example where DBH ≤10 cm; a number of reasons are suggested including performance of semantic segmentation step.The volume and scale of TLS data captured in forest plots is increasing. It is suggested that to fully utilise this data for activities such as monitoring, reporting and verification or as reference data for satellite missions an automated processing pipeline, such asTLS2trees, is required. To facilitate improvements toTLS2trees, as well as modification for other laser scanning modes (e.g. mobile and UAV laser scanning),TLS2treesis a free and open‐source software.

Detection of Barely Visible Impact Damage in Composite Structures Using Backward Sweep Vibro-thermography Technique Utilizing Asymmetry in Local Defect Resonance

ABSTRACT In this article, local defect resonance-based vibrothermography has been studied for different sweep direction and ranges. Two different carbon fiber-reinforced polymer (CFRP) composite plate has been fabricated from vacuum assisted resin transfer molding. In the first plate, a flat bottom hole has been made and two barely visible impact damages are created in other plate. The area of delamination has been determined from phased array ultrasound testing. Laser doppler vibrometry (LDV) has been performed first for different sweep ranges and directions. The CFRP plate is excited with a piezoelectric element at 150 Vpp and the vibration over defect area is captured using a single point laser doppler vibrometer, operating in scanning mode. It has been found that vibration amplitude at local defect resonance (LDR) frequency increases in narrow sweep range compared to a wideband excitation. Again, in both cases, it has been found that backward sweep produces more amplitude compared to forward one due to softening nonlinearity. An asymmetry in LDR frequency is also been observed when the sweep range is further narrowed. An uncooled microbolometer camera is used for reception in case of vibrothermography. Backward sweep is found to be more effective as compared to the forward one and the temperature increment increases in case of narrowband excitation range.

Advancement of microfluidic modulation spectroscopy as a highly sensitive protein characterization technique for the detection of small structural changes

The higher order structure (HOS) of a protein is vital to its function and activity, making it a critical component in the development of protein-based therapeutics. Characterization of HOS can be performed using various biophysical techniques, but many of these methods have limitations such as low throughput, complicated workflow, narrow concentration range, and low sensitivity. Microfluidic Modulation Spectroscopy (MMS) is an emerging technology that addresses these limitations, offering high sensitivity and automated analysis for protein secondary structure. This study evaluates and compares the different well plate formats and scan modes of two MMS instruments. The newer Apollo system features a high throughput 96-well plate format and sweep scan mode that allows a 50% reduction in sample volume consumption and measurement time compared to the previous system. By measuring two proteins with drastically different secondary structures, the results demonstrated that the measurements were highly repeatable (>99% repeatability by area of overlap) regardless of the well plate formats or the scan modes. The limit of quantitation (LOQ) for determining structural impurity using the sweep scan mode was 3.2% and significantly better than that of FTIR at 23% from previous studies. This work highlighted the advancement of MMS as a highly sensitive technique to detect small changes of protein structures due to aggregation or misfolding.

Simultaneously measure the concentrations of busulfan and phenytoin in human plasma using an HPLC-MS/MS method: Application to the TDM for children underwent hematological stem cell transplantation

AbstractIn this work, a simple and rapid high performance liquid chromatography tandem mass spectrometry (HPLC-MS/MS) method was developed and validated to carry out the simultaneous measurement of busulfan (BU) and phenytoin (PHT) in the plasma of children. In this method, plasma sample could be prepared by one-step protein precipitation using 1 mL of methanol/water (1:1, v/v). After centrifugation (14,500 rpm, 5 min, 4 °C), 10 μL of the supernatant was injected into a Hypersil Gold C18 column (150 × 2.1 mm, 5 μm, Thermo Fisher Scientific) for separation by gradient elution. Quantification was carried out using multiple reactions monitoring (MRM) under positive scan mode. In the method verification, the calibration curves of BU and PHT showed satisfactory linearity (r > 0.99) at the concentration ranging from 0.02 to 20 μg mL−1. The accuracy and precision were tested at four concentration levels (including the LLOQ level) with the relative error (RE) ranging from −0.80% to 11.45% and coefficient of variation (CV) between 0.93% and 7.74%. There was no pronounced matrix effect to interfere with the quantitative analysis. Compared to determine BU and PHT using two individual methods, less pre-treatment process, labor and blood sample volume are required in this proposed method. Finally, this method was successfully applied to the therapeutic drug monitoring of BU and PHT for children underwent hematological stem cell transplantation.

The forming quality of Tungsten-Carbide coatings synthesized in situ by laser remelting

The work aimed to improve the forming quality of multi-pass coatings synthesized by laser remelting in situ. The influence-relation model of the overlap rate on surface flatness and dilution rate of coatings was constructed by the single-factor method. The functions of laser power, scanning speed, defocusing distance, and scanning mode on the surface flatness and pore area of remelted coatings were studied by mixed horizontal orthogonal test, and the influence law of process parameters on surface flatness and internal pore area was revealed. Flatness increased first and then decreased with the increased overlap rate. Energy acting on the substrate decreased, and the dilution rate decreased. When the dilution rate was satisfied, the overlap rate corresponding to the maximum value of the flatness fitting curve was 26.7%. The scanning speed and laser power of remelting significantly affected coating flatness and the signal-to-noise ratio of the pore area. The signal-to-noise ratio of flatness to the pore area was positively correlated with laser power and negatively correlated with the scanning speed. When the scanning speed of remelting decreased, the duration of the molten pool increased, and its solidification rate decreased. Therefore, bubbles in the molten pool had sufficient time to overflow, which increased coating flatness and decreased the internal pore area.The optimum process parameters under multi-index optimization of integrated flatness and pore area were as follows using grey relational analysis: the laser power of 1,600 W, scanning speed of 3 mm/s, a defocusing distance of 10 mm, and parallel cladding direction. Sticky powders in the coating disappeared under the optimal remelting process parameters, and flatness and the internal pore area were improved. Maximum hardness was increased from 1,281.7HV to 1,454.2 HV, with an increase of 13.46%. The grain size was small and hardness was improved due to the increased tissue density in the remelting area of the coating.

System Design and Echo Preprocessing of Spaceborne Squinted Two-Dimensional Beam Scanning Synthetic Aperture Radar.

Conventional squinted sliding spotlight synthetic aperture radar (SAR) imaging suffers from substantial swath width reduction and complex processing requirements due to the continuous variation in the squint angle and the large range cell migration (RCM) throughout the data acquisition interval. A novel two-dimensional (2D) beam scanning mode for high-resolution wide swath (HRWS) imaging is proposed. The key to the novel imaging mode lies in the synchronous scanning of azimuth and range beams, allowing for a broader and more flexible imaging swath with a high geometric resolution. Azimuth beam scanning from fore to aft was used to improve the azimuth resolution, while range beam scanning was adopted to illuminate the oblique wide swath to avoid the large RCM and the serious swath width reduction. Compared with the conventional sliding spotlight mode, both the swath width and swath length could be extended. According to the echo model of this imaging mode, an echo signal preprocessing approach is proposed. The key points of this approach are range data extension and azimuth data upsampling. A designed system example with a resolution of 0.5 m, swath width of 60 km, and azimuth coverage length of 134 km is presented. Furthermore, a simulation experiment on point targets was carried out. Both the presented system example and imaging results of point targets validated the proposed imaging mode.

Measuring Melanoma Nanomechanical Properties in Relation to Metastatic Ability and Anti-Cancer Drug Treatment Using Scanning Ion Conductance Microscopy.

A cell's mechanical properties have been linked to cancer development, motility and metastasis and are therefore an attractive target as a universal, reliable cancer marker. For example, it has been widely published that cancer cells show a lower Young's modulus than their non-cancerous counterparts. Furthermore, the effect of anti-cancer drugs on cellular mechanics may offer a new insight into secondary mechanisms of action and drug efficiency. Scanning ion conductance microscopy (SICM) offers a nanoscale resolution, non-contact method of nanomechanical data acquisition. In this study, we used SICM to measure the nanomechanical properties of melanoma cell lines from different stages with increasing metastatic ability. Young's modulus changes following treatment with the anti-cancer drugs paclitaxel, cisplatin and dacarbazine were also measured, offering a novel perspective through the use of continuous scan mode SICM. We found that Young's modulus was inversely correlated to metastatic ability in melanoma cell lines from radial growth, vertical growth and metastatic phases. However, Young's modulus was found to be highly variable between cells and cell lines. For example, the highly metastatic cell line A375M was found to have a significantly higher Young's modulus, and this was attributed to a higher level of F-actin. Furthermore, our data following nanomechanical changes after 24 hour anti-cancer drug treatment showed that paclitaxel and cisplatin treatment significantly increased Young's modulus, attributed to an increase in microtubules. Treatment with dacarbazine saw a decrease in Young's modulus with a significantly lower F-actin corrected total cell fluorescence. Our data offer a new perspective on nanomechanical changes following drug treatment, which may be an overlooked effect. This work also highlights variations in cell nanomechanical properties between previous studies, cancer cell lines and cancer types and questions the usefulness of using nanomechanics as a diagnostic or prognostic tool.

Use of Stepped Carrier Frequency in Fast Scan Mode to Detect Small Targets on the Sea Surface

To detect a small target on the sea surface, we propose a detection algorithm that operates in three steps: (1) representation of three-dimensional complex cube in the (radial range, pulse time, scan time) domain by using stepped carrier frequency in fast scan mode; (2) intrascan integration to transform complex cube from the pulse time domain to the radial velocity domain by using Fourier transform; and (3) interscan integration to detect a small target by using a conventional optimal coherent detector with a Fourier relationship between stepped carrier frequency and initial radial range, and a discriminator between a true target and false targets. The proposed method improves the ability to detect of a small target, and reduces the sensitivity to sea clutter despite relatively low radial range resolution. In experiments, our proposed method could perform accurate and robust detection of a small target.

Broadband Dual-Polarized Phased Array With Dynamic Scanning Control for Intelligent Mobile Communication Application

This work investigates a low-cost, broadband, dual-polarized, beamwidth reconfigurable phased array for dynamic beam-scanning control. Both the beamwidth in the E-plane and H-plane are synchronously extended by introducing the vertically polarized (VP) field components. Then, by exploring a switch-loaded omnidirectional source, a novel dual-polarized wide/narrow beamwidth switchable or reconfigurable method is proposed. To meet the demand for intelligent mobile communication for dynamic beam steering, the dual-polarized beamwidth reconfigurable radiator as the array element is used for the phased array or MIMO designs. As a proof of concept, an interesting four-element reconfigurable dual-polarized phased array is implemented in the Sub-6 GHz band. By controlling the switch states of each element, this array can be operated in two modes: <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">wide-angle scanning coverage (V2V connection) and long-distance high-gain scanning (V2I communication)</i> . In wide-angle scanning mode, the main lobe of the array can scan from -60° to +55°, and its peak gain is 9.1 dBi. In long-distance high-gain scanning, this array can scan the beam in the range of [-35°, +35°] with a peak gain of 11.2 dBi. Besides, the isolation between different elements or polarization is greater than 13 dB. This reconfigurable phased array demonstrates the advantages of low-cost, broadband, and flexible beam-steering capability. It is expected to find broad applications in intelligent vehicular communication and low-cost phased array.

A high-eigenfrequency differential stiffness probe for high-speed scanning probe microscopy

Microcantilever probes used for high-speed scanning probe microscopy are typically required to satisfy two mutually contradicting objectives: high eigenfrequency ( ω n ) and low flexural rigidity ( k b ). The conventional design approach shortens the microcantilever’s length to increase the eigenfrequencies (as ω n ∝ 1 / L 2 ); however, this also increases the probe’s rigidity (as k b ∝ 1 / L 3 ). This paper demonstrates—through experiments and physical modelling—the design of a novel high-eigenfrequency probe by redistributing the microcantilever’s mass along its length. A 100% increase in the probe’s eigenfrequency is achieved with this modified design, even while reducing its stiffness by 50%. Through experiments, this reduced stiffness has been found to enhance the probe’s force sensitivity . Also, the probe’s design facilitates redistributing the fluid pressure between its underside surface and the sample, thereby improving the quality factor by more than 100%. Significant reduction in ‘overshoot’ and ‘parachute’ is observed in contact mode scanning at the video rate. The improvements in the image resolution are proven for a variety of sample surfaces at very high scan rates up to 40 Hz (corresponding to a linear speed of 3.20 mm s − 1 ) upon scanning over an area of 40 × 40 μ m and are successfully demonstrated to map topographies with negligible image artefacts.

Comprehensive profiling of amino and carbonyl compounds in the Hong Yao sour soup, a type of fermented sour soup, in Huangluo Yao Village of Guangxi, China

Fermented sour soup is a traditional condiment in daily southwestern Chinese cuisine. Compounds found in Hong Yao sour soup were fractionated using size-exclusion chromatography. Amino compounds were identified through derivatization with 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate and liquid chromatography tandem mass-spectrometry (LC-MS/MS) with precursor scan, followed by identification using product ion scan. Other compounds lacking amino groups were isolated using solid-phase extraction with a strong cation exchanger and detected through LC-MS in full scan mode. Carbonyl compounds, including carboxylic acids, were detected and identified by derivatization with 2-nitrophenylhydrazine and LC-MS/MS. Besides amino acids and carboxylic acids including lactic and acetic acid, amino acid metabolites such as monoamines (tyramine, pyrrolidine, tryptamine), polyamines (cadaverine, putrescine), N-acetyl- and N-lacoyl-amino acids, and α-keto acids from Val, Ile, and Leu were also detected. However, unlike Japanese rice wine, only a few dipeptides were detected. This information aids in understanding the unique characteristics of Hong Yao sour soup.

Advancements in Spaceborne Synthetic Aperture Radar Imaging with System-on-Chip Architecture and System Fault-Tolerant Technology

With the continuous development of satellite payload and system-on-chip (SoC) technology, spaceborne real-time synthetic aperture radar (SAR) imaging systems play a crucial role in various defense and civilian domains, including Earth remote sensing, military reconnaissance, disaster mitigation, and resource exploration. However, designing high-performance and high-reliability SAR imaging systems that operate in harsh environmental conditions while adhering to strict size, weight, and power consumption constraints remains a significant challenge. In this paper, we introduce a spaceborne SAR imaging chip based on a SoC architecture with system fault-tolerant technology. The fault-tolerant SAR SoC architecture has a CPU, interface subsystem, memory subsystem, data transit subsystem, and data processing subsystem. The data processing subsystem, which includes fast Fourier transform (FFT) modules, coordinated rotation digital computer (CORDIC) modules (for phase factor calculation), and complex multiplication modules, is the most critical component and can achieve various modes of SAR imaging. Through analyzing the computational requirements of various modes of SAR, we found that FFT accounted for over 50% of the total computational workload in SAR imaging processing, while the CORDIC modules for phase factor generation accounted for around 30%. Therefore, ensuring the fault tolerance of these two modules is crucial. To address this issue, we propose a word-length optimization redundancy (WLOR) method to make the fixed-point pipelined FFT processors in FFT modules fault tolerant. Additionally, we propose a fault-tolerant pipeline CORDIC architecture utilizing error correction code (ECC) and sum of squares (SOS) check. For other parts of the SoC architecture, we propose a generic partial triple modular redundancy (TMR) hardening method based on the HITS algorithm to improve fault tolerance. Finally, we developed a fully automated FPGA-based fault injection platform to test the design’s effectiveness by injecting errors at arbitrary locations. The simulation results demonstrate that the proposed methods significantly improved the chip’s fault tolerance, making the SAR imaging chip safer and more reliable. We also implemented a prototype measurement system with a chip-included board and demonstrated the proposed design’s performance on the Chinese Gaofen-3 strip-map continuous imaging system. The chip requires 9.2 s, 50.6 s, and 7.4 s for a strip-map with 16,384 × 16,384 granularity, multi-channel strip-map with 65,536 × 8192 granularity, and multi-channel scan mode with 32,768 × 4096 granularity, respectively, and the system hardware consumes 6.9 W of power to process the SAR raw data.

Photocatalytic active ZnO1−x S x @CNTs heteronanostructures

Herein, we report on the use of vertically aligned multiwall carbon nanotubes (CNTs) films as support for ZnO/ZnS photocatalytic active nanostructures. The CNTs were synthetized via a hot-filament chemical vapor deposition (HfCVD), using Fe catalyst on top of Al2O3 buffer layer. Controlled point defects in the CNTs outer walls were created by exposure to a low pressure nonthermal water vapors diffusive plasma and acted as seeds for subsequent pulsed-electrodeposition of Zn nanoparticles. This was to achieve a direct and improved contact between the nanoparticles and CNTs. To obtain ZnO, ZnS and mix phase of ZnO/ZnS spread on CNTs, the oxidation, sulfurization and 2 steps subsequent annealing in oxygen and sulfur rich atmospheres were applied. High resolution transmission electron microscopy with energy dispersive x-rays spectroscopy in scanning mode, provided the chemical mapping of the structures. X-ray diffraction (XRD) analyses proved the hexagonal phase of ZnO and ZnS, obtained after oxidation in H2O and S vapors, respectively. In the case of the samples obtained by the 2 steps subsequent annealing, XRD showed mainly the presence of ZnO and a small amount of ZnS. The benefit of the secondary annealing in S vapor was seen as an absorption enhancement of the ZnO1−x S x @CNTs sample having the absorption edge at 417 nm, whereas the absorption edge of ZnO@CNTs was 408 nm and of ZnS@CNTs 360 nm. For all the samples, compared to the bare ZnO and ZnS, the absorption red shift was observed which is attributed to the CNTs involvement. Therefore, this study showed the double sides benefit to induce the absorption of ZnO of the visible light, one from S doping and second of CNTs involvement. The absorption enhancement had a positive impact on photocatalytic degradation of methyl blue dye, showing that ZnO1−x Sx@CNTs heteronanostructure was the best photocatalyst among the studied samples.