Composition Of Residues Research Articles

Determination of Residual Municipal Solid Waste Composition from Rural and Urban Areas: A Step toward the Optimization of a Waste Management System for Efficient Material Recovery

Residual municipal solid waste (RMSW) is a rapidly expanding problem worldwide and a good waste management system could reduce concerns about its correct treatment. The purpose of this study was to characterize RMSW from urban and rural areas with the ultimate goal of estimating the recycling potential of the identified fractions and implementing waste collection and recovery methods according to the type of area that generates them. A direct sampling campaign of RMSW was performed. The results showed that the highest organic waste rate was found in the rural area (11.9%); urban-area-produced RMSW mainly constituted recyclable fractions such as plastic (26.3%), paper (21.8%), glass (3.5%) and metals (3.3%). The physical-chemical characteristics of RMSW showed levels of heavy metals below the detection threshold. The conditions necessary for composting could be met only for the organic fraction coming from rural areas as demonstrated by a pH value of 6.9 and a moisture content of 46.5%. These data will be extended to all the urban and rural areas to design appropriate disposal and/or recovery plants with profitable economic interventions that will lead to a reduction in costs in the planning of the integrated solid waste management.

Advanced culture strategy shows varying bioactivities of sulfated polysaccharides of Poria cocos

This study compares the bioactivity of six sulfated polysaccharides derived from glucose- and sucrose-feeding extracted from P. cocos. Anti-inflammatory potentials of these polysaccharides were evaluated by pretreating lipopolysaccharide (LPS)-induced inflammation in RAW264.7 cells. Of the tested polysaccharides, the sulfated polysaccharide derived from sucrose-feeding at the concentration of 40 g/l (referred to as “suc 40”) exhibited the highest anti-inflammatory activity, of 83 %, and 33 % inhibition of IL-6 and TNF-α secretion, respetively. It achieved this by inhibiting the p-38 and c-Jun N-terminal kinase (JNK) MAPK signaling pathways. On the other hand, the sulfated polysaccharide derived from glucose-feeding at a concentration of 20 g/l (referred to as “glc 20”) demonstrated the greatest anti-lung cancer activity. This was achieved by inducing apoptotic-related molecules, such as poly (ADP-ribose) polymerase (PARP) and CHOP. Furthermore, glc 20 had the highest contents of sulfate, fucose, and mannose compared to the other tested polysaccharides. This suggests that the composition of monosaccharide residues are critical factors influencing the anti-inflammatory and anti-cancer activities of these sulfated polysaccharides. Overall, this study highlights the potential of sulfated polysaccharides derived from P. cocos to function as bioactive compounds with anti-inflammatory and anti-cancer properties.

RESIDUES FROM MUNICIPAL SOLID WASTE INCINERATION: COMPOSITION, GROUNDWATER POLLUTANT LEACHING, TREATMENT TO REDUCE ENVIRONMENTAL IMPACT

Incineration is a common method for treating municipal solid waste, which reduces its mass by 70% and volume by up to 90%. However, most of the non-combustible components are subsequently concentrated in a relatively small amount of incineration residues – bottom ash and fly ash – which must be further processed and / or landfilled. The article describes the formation and composition of incineration residues, issues of recycling and environmental regulation, leaching of pollutants and the problems of its testing, methods of treating incineration residues to reduce environmental impact.

Customized High-Value Agricultural Residue Conversion: Applications in Wastewater Treatment

Wastewater treatment methods based on catalytic technology are receiving more and more attention in recent years. In order to achieve the high-value utilization of agricultural residues, the development of greener, more efficient, and economically favorable catalysts is the focus of this review. The main contents include: (i) discussions around the differences in surface morphology, chemical stability, electrical conductivity, porosity, and the specific surface area of the prepared biochar according to the biochemical composition of different agricultural residues; (ii) through the above comparison, the shortlisting and selection of suitable catalysts for the preparation of agricultural residues to improve the adsorption and catalytic performance; (iii) discussions around the interaction mode and catalytic mechanism between the surface properties of biochar and pollutants; (iv) based upon future needs, discussions around making full use of the distribution of the pyrolysis products of agricultural residue, and designing biochar-based catalysts to achieve the efficient degradation of pollutants in wastewater. The review aims to provide a waste disposal alternative for the alleviation of environmental pollution and the promotion of green chemistry as well as sustainable development.

Pyrotechnic Delay Compositions Based on BaO2: Not as "Green" as Expected.

The aims of this study were to investigate the potential of using barium peroxide as an environmentally friendly oxidising agent, to evaluate the composition of the combustion products of the developed pyrotechnic delay compositions (PDCs) and to provide information about the impact of the utilised metallic fuel (Mg, Al, Fe or Cu) on the properties of those PDCs. The PDCs exhibited acceptable friction and impact sensitivity values. This allowed conducting further experiments, e.g., determining the linear combustion velocity of the PDCs as a function of oxygen balance (OB). Based on the composition of the post-combustion residues, determined by Raman spectroscopy and SEM-EDS, an initial mechanism for the combustion of the developed PDCs was proposed.

Recent Advances in the Utilization of Tungsten Residue: A Mini Review of China

As a metal of strategic value, tungsten plays an important part in civil and military applications. Currently, China is the biggest tungsten producer all over the world, and the metallic smelting technologies for tungsten are well established. However, the harmless recovery and treatment procedures for tungsten residue remain rather underdeveloped. The treatment of tungsten residue generally includes the recovery of valuable metals (e.g., scandium, tantalum, and niobium) and the solidification of toxic elements (e.g., arsenic, lead, and chromium), which may control the transfer of these elements and metals. If treated improperly, the resource of tungsten residue may be wasted, and potential environmental risks could arise. Therefore, the safe disposition of tungsten residue has become the limit factor and an urgent problem to be solved for the sustainable development of tungsten-related industries. In this regard, we reviewed the industrial background of tungsten and the composition and toxicity characteristics of tungsten residue. In addition, particular attention was paid to the harmless utilization processes and technologies for tungsten residue, which were then systematically compared in terms of the applicable situations as well as their advantages and shortcomings. Finally, the development trend for the harmless utilization of tungsten residue was discussed, and some proposals for further studies were provided.

Grain coarsening during liquid phase sintering of zircon–glass composites

This study examined zircon grain growth during isothermal sintering of a zircon–glass composite with a zircon volume fraction of 0.525 zircon volume/solids volume, at a temperature of 1200°C, with different residence times, ranging from 5min to 1500min. Scanning electron microscopy and image analysis were used to determine zircon grain size and number in the fired test specimens. The residual glass composition was determined by energy dispersive X-ray spectroscopy. For each firing condition, the grain size number distribution was fitted to a lognormal function and to a Weibull function. In every case, the lognormal distribution described the results better. Grain size grew and distribution width decreased with sintering time in accordance with non-steady-state grain growth models. At high sintering times, the variation of average grain diameter and grain number density per unit solids cross-section fitted well to steady-state growth models. Moreover, when grain size distribution was scaled by the average size, it was practically time independent. In contrast, scaled grain distribution width was much wider than that predicted by these models. A model was developed that satisfactorily predicts zircon grain evanescence throughout the sintering process.

The Strontian Intrusive Complex: Petrography, Thermobarometry and the Influence of Titanite on Residual Melt Chemistry

Abstract Although the evolution of residual melts in magmatic systems controls their eruptability and ore-forming potential, their compositions are obscured in plutonic rocks by a protracted near-solidus evolution and the absence of interstitial glass. Here, we trace the evolution of residual melt compositions in rocks from the Strontian Intrusive Complex, Scotland, using the trace element chemistry of amphiboles, and titanites which are intergrown with amphibole rims. Laser ablation mapping reveals an abrupt change in certain trace elements in the amphibole rims, with sharp increases in Eu/Eu* and Sr/Y, and decreases in rare earth elements, Ta, Nb, and Ta/Nb ratios. Core-rim variations in these elements in titanite show the same variations as in amphibole, but are more gradual. By reconstructing the crystallisation sequence of the Strontian magmas using textural observations and thermobarometric estimates, we determine that amphibole cores crystallised prior to titanite saturation, but amphibole rims crystallised simultaneously with titanite. Using the trace element composition of the mineral phases and their modal abundance in the rock, with comparison to the whole-rock chemistry, we determine that titanite hosts the majority of the rare earth and high field strength element budget of the rocks. We therefore propose that the onset of titanite crystallisation had a profound effect on the trace element composition of late-stage residual melts at Strontian, which were inherited by the amphibole rims and subsequent titanites. This is supported by Rayleigh fractional crystallisation modelling, which demonstrates that the composition of amphibole rims cannot be explained without the influence of titanite. We therefore show that the saturation of trace element-rich phases in magmas represents a significant geochemical event in the petrogenesis of intermediate to silicic magmas. This has implications for provenance studies that attempt to reconstruct bulk rock compositions from mineral compositions, as the residual melts from which those minerals crystallise can be driven to significantly different compositions from the host magma by late-stage accessory phase crystallisation.

Teknologi Hijau Pengelolaan Bijih Nikel Laterit (Nickel Laterite Spent Ore Treatment “Green Technology”)

In pace with the rising output of electric vehicles, the nickel sector is still developing quickly. In 2022, Indonesia will manufacture 500,882.27 tons of ferro nickel, of which 197,758 tons, or 30.01%, will be able to be sold. Along with the growth of nickel mines comes technological advancements, one of which is the ability to manage wasted ore, a waste product of the nickel refining process. With the help of this study, used ore will be transformed into a useful product that can be used to control the environment. Laboratory scale testing, field scale tests, and toxicity tests (TCLP and LD50) are the techniques used. Testing for toxicity and planting on 14 tonnes of wasted ore, a byproduct of hydrometallurgical heap leaching. Limestone or a combination of biolite, agromax, and ND-201® were used to neutralize the spent ore and Fe residue composites during the process. This seeks to make the leftovers from the leaching process, the resulting runoff water, and the plants that can come from it edible. According to the test results, processed spent ore is a harmless substance that does not fall under the B3 waste category and may be utilized as an excellent planting medium for perennials and food plants. Based on BPOM quality criteria in Law No. 23 of 2017, the results of food laboratory testing revealed that food crops grown through the planting procedure utilizing discarded ore media were suitable for eating.

Effects of particle size on the pyrolysis of spruce and poplar: Thermogravimetric analyses, DAEM modelling, validation, and prediction of secondary charring

Particle size plays a crucial role in biomass pyrolysis mechanisms and their subsequent industrial uses. However, an applicable kinetic method that combines thermogravimetric data with distributed activation energy model (DAEM) adapted to the sample size is still missing. This work investigated pyrolysis kinetics of two wood species (spruce and poplar) with five particle shapes (powder, particle, 5-mm diameter cylinders with heights of 1 mm, 2 mm, and 4 mm) and one additional reaction condition (powder with lid). The experimental data were numerically simulated by two Gaussian + one exponential DAEM distributions. Thermogravimetric results evidenced a significant effect of particle geometry on char yields, which increased by 81% and 66%, from powder to 4-mm high cylinders, for spruce and poplar respectively. The increase in particle size and use of a crucible lid led to an increase of exothermic heat. Elemental analysis demonstrated a contradictory relation between carbonization and mass loss, which was explained by secondary charring. Synthetic indexes built from the kinetics parameters of the DAEM model clearly depicts the effect of particle sizes. The prediction ability of the model was checked by further experiments performed at different time-temperature patterns with several particle sizes. Finally, correlations between dimensionless residual mass (DRM) and element compositions allowed us to determine the composition of secondary charring, which consists mainly of carbon. The elemental composition of char can therefore be predicted using the difference of DAEM kinetics between fine powder and a given particle size.

Pursuing pademelon provenance: a pilot study using portable XRF to trace field-collection of museum mammal specimens

Internationally, the value and usefulness of museum zoological specimens are compromised when supporting contextual data are lost or disconnected from the specimen. In this pilot study, twelve Macropodidae Thylogale (pademelon) skins with known provenance from the Australian Museum (Sydney) were analysed using portable X-ray fluorescence spectroscopy and principal component analysis. Elemental composition of preservative residues was assessed to establish if common patterns existed and could be associated with particular field collectors. Specimens were differentiated, and the field collector deduced, based on elemental analysis of preservative residues on skins. Each of the nineteenth century field collectors, in this study, were found to have applied the same or similar preservatives to zoological specimens over a number of years, which showed a consistent pattern of practice. Additionally, the specimens obtained by each of the field collectors could be distinguished from one another based on the preservative residues. These discoveries provide exciting prospects for the use of X-ray fluorescence spectroscopy to couple museum specimens with unknown contextual data via their field collector and associated archival evidence, and hence, enable a considerable enhancement of their value as museum and research objects.

The influence of residual pectin composition and content on nanocellulose films from ramie fibers: Micro-nano structure and physical properties

In this study, cellulose nanofibril (CNF) films from ramie fibers were prepared with different pectin compositions and contents, and the influence of residual pectin on the overall performances of CNF films was evaluated. There was no significant effect of the residual pectin composition on the properties of obtained CNF films. However, when the content of residual pectin was increased from 0.45 % to 9.16 %, the surface area and water absorption of CNF films were increased from 0.2223 to 0.3300 m2/g, and from 93.51 % to 122.42 %, respectively. Pectin covers the CNF surface and act as a physical barrier between the cellulose fibrils; thus the nanocellulose films with high pectin content will have a loose and porous structure, resulting in a high surface area and a high water absorption. Besides, with the residual pectin content decreasing from 9.16 % to 0.45 %, the UVA light transmittance and tensile strength of CNF films were increased from 30.6 % to 59.9 %, and from 37.67 to 100.26 MPa, respectively. After removal of amorphous pectins in CNFs, the low pectin containing CNFs are able to pack more compactly to form a strong and thin film. This paper provides guidance for the preparation of CNF films with different performance requirements.

Acetylcholinesterase Adsorption on Modified Gold: Effect of Surface Chemistry on Enzyme Binding and Activity.

Surface chemistry plays a crucial role in the performance of biosensors and biocatalysts, where enzymes directly interact with a solid support. In this work, we investigated the effect of surface charge and hydrophobicity on the binding and activity of acetylcholinesterase (AChE) following direct adsorption to modified gold surfaces. Surface modifications included self-assembled monolayers (SAMs) terminated with -COO-, -NH3+, -OH, and -CH3 functional groups at varying mole %. We also investigated the effects of positively and negatively charged helical peptides covalently coupled to the SAM. Using spectroscopic ellipsometry, we measured the surface concentration of AChE on each modified surface after 1 h of adsorption. We found that surface concentration was directly proportional to surface hydrophobicity (r = 0.76). The highest binding was observed on the more hydrophobic surfaces. We also measured the specific activity of AChE on each surface using a colorimetric assay and found that activity was inversely proportional to surface hydrophobicity (r = -0.71). The highest activity was observed on the more hydrophilic surfaces. Plotting specific activity versus surface concentration showed a similar relationship, with the highest activity observed at low AChE densities (∼20% of a monolayer) on surfaces terminated with 50% -COO- or -NH3+ and 50% -CH3 functional groups. Interestingly, this is similar to the approximate composition of hydrophobic versus hydrophilic amino acid residues on the surface of AChE. These surfaces also exhibited the highest total activity: a ∼100% improvement over bare gold due to a combination of moderate binding and high activity retention. This work highlights the importance of developing new attachment strategies beyond direct adsorption that promote, tune, and optimize both high binding and high activity retention.

Microbial community attributes supersede plant and soil parameters in predicting fungal necromass decomposition rates in a 12-tree species common garden experiment

Although dead fungal mycelium (necromass) represents a key component of biogeochemical cycling in all terrestrial ecosystems, how different ecological factors interact to control necromass decomposition rates remains poorly understood. This study assessed how edaphic parameters, plant traits, and soil microbial community structure predicted the mass loss rates of different fungal necromasses within experimental monocultures of 12 tree species in Minnesota, USA. Necromass decay rates were most strongly driven by initial chemical composition, being significantly slower for fungal necromass with higher initial melanin content. Of the extrinsic ecological factors measured, variation in the amount of mass remaining for both low and high melanin necromass types was significantly predicted by soil bacterial richness and fungal community composition, but not by any soil microclimatic parameters or plant traits. Further, the microbial communities governing decay rates varied depending on the initial necromass chemical composition, suggesting that extrinsic and intrinsic factors interacted to propel decomposition. Finally, we also found significant positive relationships between the amount of remaining fungal necromass and soil carbon and nitrogen concentrations. Collectively, these results suggest that, after the initial chemical composition of dead fungal residues, soil microbial communities represent the main drivers of soil necromass degradation, with potentially large consequences for soil carbon sequestration and nutrient availability.

Matrix Metalloproteinase-9 Expression Is Associated with the Absence of Response to Neoadjuvant Chemotherapy in Triple-Negative Breast Cancer Patients.

Triple-negative breast cancer (TNBC) is particularly challenging due to the weak or absent response to therapeutics and its poor prognosis. The effectiveness of neoadjuvant chemotherapy (NAC) response is strongly influenced by changes in elements of the tumor microenvironment (TME). This work aimed to characterize the residual TME composition in 96 TNBC patients using immunohistochemistry and in situ hybridization techniques and evaluate its prognostic implications for partial responders vs. non-responders. Compared with non-responders, partial responders containing higher levels of CD83+ mature dendritic cells, FOXP3+ regulatory T cells, and IL-15 expression but lower CD138+ cell concentration exhibited better OS and RFS. However, along with tumor diameter and positive nodal status at diagnosis, matrix metalloproteinase-9 (MMP-9) expression in the residual TME was identified as an independent factor associated with the impaired response to NAC. This study yields new insights into the key components of the residual tumor bed, such as MMP-9, which is strictly associated with the lack of a pathological response to NAC. This knowledge might help early identification of TNBC patients less likely to respond to NAC and allow the establishment of new therapeutic targets.

Estimation of Absorbed Dose due to Gas Bremsstrahlung Based on Residual Gas in Electron Storage Rings

Gas bremsstrahlung, generated by the interaction between stored electrons and residual gas in electron storage rings, is an important radiation source for the shielding of synchrotron radiation (SR) facilities. In recent SR facilities, hydrogen was found dominant in the residual gas of the vacuum chambers of the electron storage rings, although air has been conventionally assumed as the bremsstrahlung target for the shielding designs of SR beamlines extended from the electron storage ring. To study the effect of residual gas composition on the dose rate outside shields, we calculated the intensity of gas bremsstrahlung based on the gas composition for both the air and the residual gas expected in the recent electron storage rings using an analytical formula and general-purpose Monte Carlo codes for particle transport calculations. The analytical shielding calculation with a realistic gas composition was found to well reproduce the energy spectra of gas bremsstrahlung simulated by the Monte Carlo codes. The correction factors between the air and the realistic gas compositions are applied to the conventional analytical formulas for dose estimation of secondary radiations generated by the interaction between the bremsstrahlung from air and beamline components.

Differentiated Fractionation of Various Biomass Resources by p-Toluenesulfonic Acid at Mild Conditions.

Biomass is the ideal substitute for petrochemical resources because of its renewable and abundant sources. p-Toluenesulfonic acid (p-TsOH) can effectively separate lignin from biomass under mild conditions, so it is highly expected in biomass fractionation to improve the utilization efficiency. In this study, we investigated the effect of p-TsOH differentiated fractionation of poplar sawdust, eucalyptus sawdust, and rice straw below 100 °C. According to the experimental results, upon pretreatment by p-TsOH of the three kinds of raw biomass, most of the lignin and hemicellulose of poplar sawdust and eucalyptus sawdust were removed, whereas the cellulose was retained, but most of the hemicellulose and cellulose of rice straw were kept, whereas the lignin was removed at similar conditions. The structures and compositions of pretreatment residues, lignin, and hemicellulose extracted from raw biomass were characterized by XRD, FTIR, HSQC-NMR, XPS, and SEM. The differentiated fractionation mechanism of biomass was analyzed. A better recognition and understanding of the factors affecting biomatrix opening and fractionation will allow for the identification of new pretreatment strategies that improve biomass utilization and permit the rational enzymatic hydrolysis of cellulose.

Effect of Agro-industrial Residue Composition on the Production of Endo-1, 4-β-Xylanase by Bacillus pumilus

Background: Bacillus pumilus grows on different substrates and produces Endo-1, 4-β-xylanase (EXase) which degrades the hemicellulose and produces xylooligosaccharides. EXase found applications in paper, pulp and in food industries. The objective of this study is to investigate the compositional effect of lignocellulosic biomass as substrate for the production of EXase by Bacillus pumilus. Methods: The EXase production depends on the composition of substrate (agro-industrial residue), Bacillus pumilus, media composition and performance of fermentation method. Thus, we have evaluated the effect of composition on the production of EXase. The higher content of hemicellulose of substrate indulges EXase production. Moreover, ICP-MS, FTIR spectroscopy, XRD and SEM analyses confirmed that significant alternation of substrate structure by Bacillus pumilus due to the EXase actions. Result: Based on the results of the hydrolytic enzyme activation and characterization studies suggested that Bacillus pumilus produced EXase highest for sugarcane bagasse 1190 U/mg by degrading the sugarcane bagasse as a low-cost carbon sources and effective media composition (Minimal Salt Yeast Extract Nutrient Medium) for nitrogen source, also with the presence of metal ions such as Cu++, Fe++, Mn++ for increased the production of EXase.

Integrated approaches to understanding animal exploitation and dairying in the Central European Early Neolithic: a case study from Ludwinowo 7 (Kuyavia, Poland; c. 5250–5000 cal BC)

Recent genetic studies point towards 6th millennium BC central Europe as the core region for the emergence of the lactase persistence (LP) gene mutation -13,910*T, making it important to understand the intensity of milk production and consumption among Linearbandkeramik (or LBK) farming groups. However, it is not known if milking was part of the LBK Neolithic “package” from the start, or if it displayed a discontinuous pattern in time and space. Documenting the changing nature of prehistoric animal exploitation requires integrating multiple strands of evidence and here we detail multi-proxy research into animal management strategies and the intensification of dairying in Neolithic Europe, using the LBK site of Ludwinowo 7 in central Poland as a case study. Lipid biomarker and stable isotope compositions of food residues from vessels provide qualitative and quantitative assessments of the major animal products acquired and processed, while zooarchaeological analyses identify slaughter and butchery practices, revealing the nature of meat, milk and fat exploitation. Stable carbon and oxygen isotope analyses on cattle teeth are also undertaken to define seasonal herd management. This combined approach offers an integrated picture of animal exploitation and milk use at the central European LBK site of Ludwinowo.

Assessment of combustion residual leachate volume, composition, and treatment costs

Combustion residuals and the resulting leachate from storage sites represent a large volume of wastewater in the United States (U.S.) that has not been quantified. This work estimates the constituents present, volume of wastewater, and costs of treatment for both combustion residual landfill leachate and the leachate from surface impoundment closures. Combustion residual landfill leachate produced from contact with bituminous coal combustion byproducts is generally predicted to be higher in lithium and manganese, whereas landfill leachate produced from contact with subbituminous coal combustion byproducts is generally predicted to be higher in mercury and vanadium. The annual volume of a single landfill with combustion residual leachate can reach more than 800,000 cubic meters. This leachate represents an annual volume of 26.8–42.8 million cubic meters nationally. Closing surface impoundments can yield between 830 and 1040 cubic meters of leachate nationally for a three-year closure period. Costs as low as $1.5/m3 or as high as $95/m3 are observed. Treatment trains will need to remove 72% of total suspended solids (TSS), 87% of arsenic, and 64% of mercury from landfill leachate. When applied to impoundments, these treatment trains would need to remove 97% of arsenic.