QAM Modulation Schemes Research Articles

Throughput improvement in ACO-OFDM-based VLC systems using noise cancellation and precoding techniques

One of the primary challenges faced by visible light communication (VLC) systems employing optical orthogonal frequency division multiplexing is the peak-to-average power ratio (PAPR). This study is dedicated to designing, simulating, and evaluating bit error rate (BER) and PAPR reduction methods tailored for the VLC broadcasting system. The asymmetric clipped optical orthogonal frequency division multiplexing (ACO-OFDM) scheme is highlighted in this work for its impressive performance. Therefore, the proposed PAPR mitigation methodologies applied to ACO-OFDM. The proposed PAPR reduction strategy involves 5 distinct precoding methodologies. The PAPR was mitigated by 3.485 dB after applying the DST precoding methodology. Still, the WHT precoding methodology can achieve PAPR reduction by 1.131 dB, without BER performance degradation, with respect to the conventional ACO-OFDM system. Furthermore, the work addresses another challenge in VLC systems: the bit error rate (BER). This is accomplished by introducing approaches to Time Domain Noise Cancelation and Frequency Domain Noise Cancelation (FDNC). The BER performance of these 2 receiver models is nearly the same. The simulation results indicate the system performance enhancement after applying noise cancellation approaches by 1.65 dB at the 4-QAM modulation scheme and 2.97 dB at the 1024-QAM modulation scheme. The 16-QAM modulation scheme, after applying DST and WHT methodologies alongside noise cancellation approaches, can enhance both PAPR by 20.83% and 6.76%, but the Eb/N0 performance enhancement by 10.10% and 14.64%, respectively. Additionally, the effectiveness and validity of the proposed schemes are verified by comparing them with relevant literature reviews on PAPR reduction techniques and selecting an optimal choice among them.

Performance Analysis of BER and SNR Performance in High-QAM Modulations Using Advancements in MIMO Systems

Wireless communications is one of the most active areas of technology development of our time. This development is being driven primarily by the transformation of what has been largely a medium for supporting voice telephony into a medium for supporting other services, such as the transmission of video, images, text, and data. Today, the widely deployed network type is based on a centralized approach that requires a network point of access, commonly called the Access Point (AP), to serves as a gateway between the mobile device and the Internet. The obtained results demonstrate that spatial diversity along with the power of STBC significantly improves the error performance in frequency selective wireless fading channels. The BER level is depend on the modulation type, SNR value and channel behavior. Modulation schemes that we have used in this paper are 4-QAM, 8-QAM, 16-QAM and 64-QAM which further improved using forward error correction codes (FEC). A comparison is made between the diversity gains of MIMO systems in terms of BER for high QAM modulation scheme. This work presents, a simulation toll MATLAB R2023a used for model implemented using Nakagami channel to study the performance analysis of Bit Error rate (BER) V/S Signal to Noise ratio (SNR). Keywords: AWGN, BER, Fading Channel, MIMO System, Nakagami, OFDM, QAM Modulation, SNR, STBC etc.

A Temporal Methodology for Assessing the Performance of Concatenated Codes in OFDM Systems for 4K-UHD Video Transmission

The communication channel is a critical part of the process of information degradation. In the 4K ultra-resolution video transmission domain, the communication channel is a crucial part where information degradation occurs, inevitably leading to errors during reception. To enhance the transmission process in terms of fidelity, advanced technologies such as digital video broadcasting terrestrial (DVB-T) and its evolutionary successor, digital video broadcasting terrestrial second generation (DVB-T2), are utilized to mitigate the effects of data transmission errors. Within this scenario, this research presents an innovative methodology for the temporal analysis of 4K ultra-resolution video quality under the influence of additive white Gaussian noise (AWGN) and Rayleigh channels. This analytical endeavor is facilitated through the application of concatenated coding schemes, specifically, the Bose–Chaudhuri–Hocquenghem concatenated low-density parity check (BCH-LDPC) and Reed–Solomon concatenated convolutional (RS-CONV) coders. A more comprehensive understanding of video quality can be attained by considering its temporal variations, a crucial aspect of the ongoing evolution of technological paradigms. In this study, the Structural Similarity Index (SSIM) serves as the main metric for quality assessment during simulations. Furthermore, the simulated Peak Signal-to-Noise Ratio (PSNR) values validate these findings, exhibiting consistent alignment with the SSIM-based evaluations. Additionally, the performance of the BCH-LDPC significantly outperforms that of RS-CONV under the 64-QAM modulation scheme, yielding superior video quality levels that approximate or surpass those achieved by RS-CONV under QPSK (Quadrature Phase Shift Keying) modulation, leading to an increase in spectral efficiency. This enhancement is evidenced by SSIM gains exceeding 78% on average. The computation of average gains between distinct technologies in video quality analysis furnishes a robust and comprehensive evaluation framework, empowering stakeholders to make informed decisions within this domain.

Comparisons of PSK, APSK, and QAM over AWGN and fading channels

In addition to the thermal noise, communication systems can normally experience various fading because of objects reflecting the signal. PSK, APSK, and QAM modulation schemes are widely used in communication systems. It is thus essential to know how well these schemes can perform in different fading channels. This research explores the BER performance of these modulation schemes in common and typical channel models including AWGN, Rayleigh fading, Rician fading, and Nakagami fading channels by simulations in MATLAB. The BER curves over a range of SNR and symbol constellation diagrams are obtained. It is found that Rayleigh and Nakagami fading distort signals most and impacts of Rician fading in LoS case and AWGN can be mitigated significantly by increasing the SNR. Furthermore, the QAM has better BER performance in fading channels while PSK and APSK perform better in AWGN channels when the number of bits of one symbol is relatively small. Selections of modulation schemes should depend on the specific circumstances and the optimization of them is required when large numbers of bits are transmitted by one symbol.

Hybrid Radio over Fiber with Radio over Free Space Optic for 5G Fronthaul Network Implementation in Urban Areas

Optical fiber can meet the demand for fronthaul on 5G networks that offer high bandwidth, large capacity, high data rate and is free from electromagnetic interference. However, deploying infrastructure faces issues like permits and high costs. Hybrid Radio over Fiber (RoF) technology with Radio over Free Space Optic (RoFSO) can be a solution in urban areas, where the installation requires high costs. This research investigates a hybrid RoF-RoFSO scheme at a frequency of mmWave 26 GHz by considering atmospheric attenuation values arising from meteorological effects, such as rain, smog, and dust, using Optisystem. This research considers QPSK, 16-QAM, and 64-QAM modulation schemes, distance variations on the FSO and the meteorological data from the Indonesian Meteorology, Climatology and Geophysics Agency (BMKG) from March 2022 to May 2022. The results show that attenuation due to high rainfall is the main cause of signal quality degradation and limits the transmission distance on the FSO link. The maximum distance is 600 m using the QPSK and 16-QAM modulation schemes, while for the 64-QAM modulation scheme, the maximum transmission distance is 500 m. Meanwhile, damping values caused by foggy and dusty conditions can reach distances of up to 1000 m for the three modulation schemes.

Analysis of throughput and error rate of 16-QAM, 64-QAM, and 256-QAM O-NOMA waveforms

Abstract This study presents a comprehensive analysis of the throughput performance, spectrum efficiency, and block error rate (BLER) of optical non-orthogonal multiple access (O-NOMA) waveforms using 16-quadrature amplitude modulation (QAM), 64-QAM, and 256-QAM modulation schemes. The aim is to assess the trade-offs between data rate, spectral efficiency, and error performance in O-NOMA systems. The analysis reveals that higher-order modulations, such as 64-QAM and 256-QAM, offer higher data rates and improved spectrum efficiency compared to 16-QAM. Furthermore, the study investigates the spectrum performance of the O-NOMA waveforms. The results indicate that higher-order modulations may utilise the spectrum more efficiently, maximising the data throughput within the available bandwidth. Moreover, the BLER analysis provides insights into the error performance of the O-NOMA waveforms. It quantifies the probability of errors occurring in a block of transmitted data and evaluates the system’s reliability. The analysis reveals that 256-QAM O-NOMA achieves lower BLER and high throughput in uplink and downlink as compared with the 16 and 64-QAM O-NOMA frameworks.

Performance of PAPR for Different Modulation Technique Using Cluster Scrambling Codeword Shifting Technique in F-OFDM Systems

Filtered-OFDM (F-OFDM) is one of the proposed 5G system candidates. In order to achieve service diversification, it must be able to support a large number of asynchronous subband transmissions. However, the transmitted signal in a multi-carrier transmission system with different subcarriers has a high peak-to-average power ratio (PAPR). Therefore, the main problem of F-OFDM systems is the high PAPR in the system, which leads to poor performance and excessive power consumption due to numerous distortions. This study introduces a technique based on codeword structure manipulation known as Cluster Scrambling Codeword (CSC) to achieve better reduction of PAPR with the evaluation of the performance of QAM and APSK modulation. This is a new formulation of the bit data sequence shifting approach that can reduce PAPR more effectively than the conventional scheme. Simulation results show that CSC with 256 QAM modulation scheme provides a PAPR reduction better than the conventional F-OFDM system.

Flexible mm-Wave Sigma-Delta-Over-Fiber MIMO Link

Millimeter-wave and multiple-input-multiple-output (MIMO) technologies combine broad bandwidth with spatial diversity to offer a greater data rate. This paper investigates a flexible millimeter-wave sigma-delta-over-fiber based transmitter solution with digital beamforming MISO and MIMO functionality. Those functions are controlled by a central unit connecting a remote radio head with a standardized QSFP28 fiber link. The central unit generates binary encoded intermediate frequency signals using bandpass sigma-delta modulation. The QSFP28 based fiber link transmits the intermediate frequency bitstreams to the remote radio head. The remote radio head consists of a QSFP28 module, <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$90^{\circ }$</tex-math></inline-formula> hybrids, and upconverters. The remote radio head feeds four parallel, independent, coherent, and central-unit controlled 28 GHz signals to a linear array transmitting antenna. The transmitter performance is experimentally verified, demonstrating up to 800 Msym/s at an EVM/NMSE of 6.7%/-23.5 dB when tested with a 64 quadrature amplitude modulation (64-QAM) modulation scheme. Digital over-the-air beamforming MISO functionality is demonstrated up to 700 Msym/s across 1 m wireless distance. MIMO communication capabilities is demonstrated by over-the-air transmission of two independent 500 Msym/s to two spatially separated receivers. The results show that the proposed link can be used for realization of scalable, low-cost and flexible transmitter solution for emerging distributed antenna systems.

Design of Hybrid Beamforming System Based on Practical Circuit Parameter of 6-Bit Millimeter-Wave Phase Shifters

This paper addresses the design of a hybrid beamforming system considering the circuit parameter of six-bit millimeter-wave phase shifters based on the process design kit. The phase shifter design adopts 45 nm CMOS silicon on insulator (SOI) technology at 28-GHz. Various circuit topologies are utilized, and in particular, a design is presented based on switched LC components, connected in a cascode manner. The phase shifter configuration is connected in a cascading manner to get the 6-bit phase controls. Six different phase shifters are obtained, which are 180°, 90°, 45°, 22.5°, 11.25°, and 5.6°, with a minimum number of LC components. The circuit parameters of the designed phase shifters are then incorporated in a simulation model of hybrid beamforming for a multiuser MIMO system. The number of OFDM data symbols used in the simulation is ten for eight users, 16 QAM modulation schemes, −25 dB SNR, 120 simulation runs, and around 170 h runtime. Simulation results are obtained considering four and eight users, assuming accurate technology-based models of RFIC components of the phase shifter as well as ideal phase shifter parameters. The results indicate that the performance of the multiuser MIMO system is affected by the accuracy level of the phase shifter RF component models. The outcomes also reveal the performance tradeoff based on user data streams and the number of BS antennas. By optimizing the amount of parallel data streams per user, higher data transmission rates are achieved, while maintaining acceptable error vector magnitude (EVM) values. In addition, stochastic analysis is conducted to investigate the distribution of the RMS EVM. The outcomes show that the best fitting of RMS EVM distribution of the actual and ideal phase shifters agreed with the log-logistic and logistic distributions, respectively. The obtained (mean, variance) values of the actual phase shifters based on accurate library models are (46.997, 481.36), and for ideal components the values are (36.47, 10.44).

Asymmetric hybrid full-duplex POF-based VLC transmission links

This paper presents an asymmetric full-duplex solution based on visible light communications (VLC) for indoor wired and wireless hybrid signal transmission. The signal is distributed by a polymer optical fiber (POF) link and passively radiated. The proposed system includes two VLC links: a low-speed downlink and a high-speed uplink using an image sensor (IS) and photodiode detection (PD) based receivers. PD-based system communication performance is evaluated by means of error vector magnitude (EVM) for different modulation orders quadrature phase shift keying (QPSK), 16- and 64-quadrature amplitude modulation (QAM), while the IS-based system is characterized in terms of the success of reception (SoR). High-speed data transmission up to 160 Mbps with a 16-QAM modulation scheme and low-speed data transmission up to 500 bps with 98.6% of SoR using a non-return zero on–off keying (NRZ-OOK) scheme over a 1.5 m optical wireless link are demonstrated. Finally, simulations of the wireless channel are performed to evaluate the misalignment tolerance of the system; and, to estimate the uplink performance at longer distances.

Novel Real-Time Decision-Based Carrier Tracking for Software-Defined Radios Using M-ARY QAM Modulation

In this paper, a scalable and real-time decision-based carrier tracking for software defined radio (SDR) for M-ary QAM modulation has been proposed and tested in real-time using the universal software radio peripheral (USRP)-2922. The proposed system provides real-time decision-based carrier tracking for improved efficiency and performance. The real-time transfer of data has been done using the USRP-2922 hardware using the M-ary QAM modulation scheme for data transmission. The novelty of the proposed system is that one can transfer random data (binary bits), text or an image which can be encoded using the desired forward error correction codes (FEC) namely the convolution coding/Viterbi soft decision decoding and the turbo coding/decoding. The proposed novel SDR transceiver system with real-time decision-based carrier tracking shows an improved performance for different parameters such as the bit error rate (BER) and signal to noise ratio (Eb/No).

A MATLAB Simulink Study on the Performance of QAM Modulation Scheme in AWGN, Rayleigh, and Rician Fading Channels: BER Analysis

Wireless communication is the fastest-growing segment in the communication industry, with mobile communication being the most widely used. However, it faces several technical challenges, such as Fading, Shadowing, Interference, and Propagation path loss. Meeting the higher demand for capacity with high-quality service is crucial. Orthogonal Frequency Division Multiplexing (OFDM) is a technique that converts wideband signals into narrowband signals for transmission, making it a suitable option for high bandwidth data transmission. The transmission of these narrowband signals is executed with an orthogonal carrier. This paper focuses on building a QAM model using MATLAB to simulate Bit Error Rate (BER) performance for real data communication under different communication channels, including AWGN and fading channels (Rayleigh and Rician). The aim is to investigate the reduction of noise and bit error rate in communication channels. The simulation model built for this research work demonstrates that QAM scheme performs better in AWGN channels than Rayleigh or Rician fading channels.

Continuous-unconstrained and global optimization for PSO-PTS based PAPR reduction of OFDM signals

Orthogonal frequency division multiplexing (OFDM) is a superior technology for the high-speed data rate of wire-line and wireless communication systems. However, one of the major drawbacks of OFDM signals is the high peak-to-average power ratio (PAPR) problem inherent in 5G waveform design. High PAPR causes OFDM signal distortion in the nonlinear region of the high power amplifier (HPA), and signal distortion leads to a decrease in bit error rate (BER). Partial transmit sequence (PTS) technique is a very attractive technique for PAPR reduction. However, to match the optimum condition on PTS for PAPR reduction, the computational unpredictability and cost of traditional PTS strategy are enormous, thus it is urgent to enhance computational efficiency to obtain the optimal PTS. In this paper, an improved scheme called Continuous-Unconstrained Particle Swarm Optimization based PTS (CUPSO-PTS) technique for optimum phase rotation factors searching is presented. A class of continuous-phase PTS schemes has been proposed to obtain the global optimal phase factor, and the theoretical boundaries can be determined in the continuous-unconstrained searching space. Conversely, when the phase factor values in continuous-unconstrained domain, the equivalent unconstrained PTS optimization can drastically accelerate convergence and reduce total calculation cost. In this paper, we compare the performance of Binary PSO based PTS (BPSO-PTS) scheme and Elitist Genetic Algorithm based PTS (EGA-PTS) scheme for 16-QAM modulation scheme. Theoretical analysis and simulations show that the proposed CUPSO-PTS scheme could provide a significant PAPR reduction in the OFDM system, which outperforms the OFDM systems with the traditional PTS scheme by 0.55 dB at CCDF of 10−3 in PAPR reduction. And 84.74% computational complexity is saved.

Irregular Vector Turbo Codes with low complexity

The term Block Turbo Code typically refers to the iterative decoding of a serially concatenated two-dimensional systematic block code. This paper introduces a Vector Turbo Code that is irregular but with code rates comparable to those of a Block Turbo Code (BTC) when the Bahl Cocke Jelinek Raviv algorithm is used. In BTC’s, the horizontal (or vertical) blocks are encoded first and the vertical (or horizontal) blocks second. The irregular Vector Turbo Code (iVTC) uses information bits that participate in varying numbers of trellis sections, which are organized into blocks that are encoded horizontally (or vertical) without vertical (or horizontal) encoding. The decoding requires only one soft-input soft-output decoder. In general, a reduction in complexity, in comparison to a BTC was achieved for the same very low probability of bit error (10^{-5}). Performance in the AWGN channel shows that iVTC is capable of achieving a significant coding gain of 1.28dB for a 64QAM modulation scheme, at a bit error rate of 10^{-5}over its corresponding BTC. Simulation results also show that some of these codes perform within 0.49dB of capacity for binary transmission over an AWGN channel.

A 0.66mW 400 MHz/900 MHz Transmitter IC for In-Body Bio-Sensing Applications.

A sub-1GHz transmitter (TX) integrated chip (IC) with ultra-low power consumption and moderately high adjacent channel power rejection (ACPR) is presented for in-body bio-sensing applications. The 400 MHz 12-phase digital power amplifier (DPA) is implemented with the proposed 16QAM modulation scheme to improve the energy efficiency. The TX IC also contains a 900 MHz FSK TX realized with a symmetrical edge-combiner, which can be used in the low accuracy mode. A fully digital modulator with band shaping is integrated on the chip for the improvement of ACPR performance. Fabricated in 65-nm CMOS process, the chip occupies an active area of 0.75 mm2. Under 0.5 V supply voltage, the TX consumes less than 0.66 mW power consumption while delivering -15 dBm of output power when operating at both bands. The presented TX has an energy efficiency performance comparable to the state-of-the-arts low power designs, with the measured average energy consumption of 64.5/220 pJ/bit, and the measured figure-of-merit (FoM) of 2.04/6.98 nJ/(bit · mW) for the two bands. Compared with the state-of-the-arts sub-1mW designs in literatures, the ACPR is improved by at least 13 dB.

Design and Synchronization Procedures of a D&F Co-Operative 5G Network Based on SDR Hardware Interface: Performance Analysis.

Software defined radio (SDR) is a commonly used platform for its ease of operation and cost-effectiveness for the development and testing of real wireless communication systems. By supporting high transmission rates and enabling fast and cost-effective deployments, mainly in millimeter-wave (mmWave), the co-operative 5G network has been standardized by 3GPP Release 16. In this paper, a decode-and-forward (D&F) co-operative hardware network is proposed as one of the key technologies for future 5G/6G wireless networks. The proposed system consists of an emulated base station processing unit (gnodeB), a D&F protocol and the user equipment (UE). In particular, the design of the D&F relay node is based on an MIMO layer 2 relay technology. A testbed based on an SDR platform and Matlab software, in which the physical broadcast channel (PBCH) transmission, physical downlink control channel (PDCCH), physical downlink shared channel (PDSCH), and downlink shared channel (DL-SCH) for transport channel coding, according to the 3GPP standardized 5G downlink signal, has been designed. The key performance indicators (KPIs), namely EVM, BER, and throughput, were measured for 5G signals with 64-QAM and 256-QAM modulation schemes. The obtained results show that the D&F co-operative 5G network achieves substantially improved KPIs in the communication between the gnodeB and the UE in an outdoor-to-indoor scenario. Furthermore, it has been demonstrated that the D&F protocol presents a good performance and behavior being compared to one commercial equipment.

Analysis of energy harvesting in SWIPT using bio-inspired algorithms

ABSTRACT In this paper, we consider a power splitting (PS)-based simultaneous wireless information and power transfer (SWIPT) system, which is having I and Q (in-phase and quadrature) imbalance hardware impairment. The prime objective of this paper is to maximize the harvested energy for a SWIPT PS system, satisfying a minimum signal to noise ratio (SNR) requirement for information signal processing in the presence of IQ imbalance hardware impairment. The paper uses four types of bio-inspired algorithms like Particle Swarm Optimisation, Artificial Bee Colony, Firefly Algorithm and Invasive Weed Optimisation to attain the maximum harvested energy considering parameters of PS ratio, amplitude and phase imbalances in a Rayleigh fading environment. The simulation results show that under ideal power conversion efficiency and minimum hardware impairments, a maximum SNR of 16.7 dB and harvested energy of 11 dB is achieved for a transmit power of 20 dB in SWIPT systems for IWO bio-inspired algorithms in the 32 QAM modulation scheme.

Analysis of cyclic prefix length effect on ISI limitation in OFDM system over a Rayleigh-fading multipath

&lt;span&gt;In this work, the influence of the cyclic prefix on the performance of the OFDM system is studied. We worked out an OFDM transceiver using a 16 QAM modulation scheme, a comparison of the BER for various lengths of the cyclic prefix has been achieved, and the influence of the noise introduced in the channel has been highlighted, for both a Gaussian and Rayleigh noise. The simulation was carried out on MATLAB where the curves of the BER for various lengths of the cyclic prefix are given and compared. We also adopted as a metric the QAM constellation to show the dispersion of the carriers as a consequence of the transmission channel, the mitigation of this effect by the CP is noticeable.&lt;/span&gt;

Performance Analysis of Two-Hop mmWave Relay Nodes over the 5G NR Uplink Signal

In this paper, the uplink in a two-hop 5G new radio co-operative system using Relay Nodes (RNs) in millimeter bands has been simulated and studied. We focus on an uplink Amplify-and-Forward Relay Node (A&amp;F RN) and Decode-and-Forward Relay Node (D&amp;F RN) with an mmWave-band transceiver chain (Tx/Rx). We study two uplink mmWave MIMO D&amp;F relaying protocols assuming, firstly, the complete knowledge of the uplink channel and, secondly, the uplink channel estimation through a Least Square (LS) algorithm. To verify the benefits of the proposed uplink mmWave MIMO co-operative network, a link-level co-operative simulator has been developed using MatlabTM and SimulinkTM software, where an indoor-to-outdoor scenario and mmWave transceiver with off-the shelf components are considered. The main novelty of this link-level co-operative simulator and the implemented relay nodes is the usage of signals with 5G NR features, such as UL-SCH transport channel coding and PUSCH generation, which are the other main contributions of this article. Based on the numerical results in terms of the achievable Bit Error Rate (BER) and throughput, we show that the two-hop uplink co-operative network substantially improves the performance in the communications between the NR-User Equipment (NR-UE) and the logical 5G Radio Node (gNodeB). For example, the results from using uplink mmWave NR-D&amp;F protocols far exceed those achieved with the uplink mmWave NR-A&amp;F algorithm; in the case of the 64-QAM modulation scheme for the SISO technique, an improvement of 6.5 Mbps was achieved using the D&amp;F PCE protocol, taking into account that the 256-QAM constellation is higher by 4.05 Mbps. On the other hand, an average throughput enhancement of 28.77 Mbps was achieved when an uplink mmWave (2 × 4 × 4) D&amp;F PCE strategy was used versus an uplink mmWave SISO D&amp;F LS protocol for a Signal-to-Noise Ratio (SNR) = 20 dB and 64-QAM signal. However, an improvement of 56.42 Mbps was reached when a 256-QAM modulation scheme was employed. Furthermore, this paper introduces the first study to develop an uplink mmWave MIMO 5G co-operative network platform through a Software Defined Radio (SDR) from a practical implementation point of view.

An adaptive 3-Dimensional hierarchical QAM scheme for elastic optical network

In this paper, a novel 3-Dimensional adaptive hierarchical Quadrature Amplitude Modulation (QAM) scheme for elastic optical networks has been introduced. The scheme can adjust the spacing between constellation points and control bit-mapping to provide different degrees of protection according to channel conditions or Quality of Service (QoS) requirements. The simulation results indicate that the multi-dimensional hierarchical constellation effectively improves the receiver sensitivity and reduces the bit error rate of the system. The 3D-AH-8/64QAM modulation scheme can obtain a maximum of 3.3 dB and 5.7 dB SNR gains respectively compared with 2D-8QAM and 2D-64QAM. The proposed scheme has a huge potential in the future high-speed elastic optical network.