Porous Network Research Articles

MICP treated sand: insights into the impact of particle size on mechanical parameters and pore network after biocementation

Microbiologically Induced Calcium Carbonate Precipitation (MICP) is a technology for improving soil characteristics, especially strength, that has been gaining increasing interest in literature during the last few years. Although a lot of influencing factors on the result of MICP are known, particle size and shape of the particles remain poorly understood. While destructive measuring of compressive strength or calcium carbonate content are important for the characterization of samples these methods give no insight into the internal structures and pore networks of the samples. X-ray microcomputed tomography (micro-CT) is a technique that is used to characterize the internals of rocks and to a certain degree MICP-treated soils. However, the impact of filtering and image processing of micro-CT Data depending on the type of MICP sample is poorly described in the literature. In this study, single fractions of local quarry were treated with MICP through the ureolytic microorganism Sporosarcina pasteurii to investigate the influence of particle size distribution on calcium carbonate content, unconfined compressive strength and the reduction of water permeability. Additionally, micro-CT was conducted to obtain insights into the resulting pore system. The impact of the Gauss filter und Non-local means filter on the resulting images and data on the pore network are discussed. The results show that particle size has a significant impact on the result of all tested parameters of biosandstone with lower particle size leading to higher strength and generally higher calcium carbonate content. Micro-CT data showed that the technology is feasible to gain valuable insights into the internal structures of biosandstone but the resolution and signal-to-noise ratio remain challenging, especially for samples with particle sizes smaller than 125 µm.

Thermophysical Investigation of Multiform NiO Nanowalls@carbon Foam/1-Octadecanol Composite Phase Change Materials for Thermal Management.

Multiform NiO nanowalls with a high specific surface area were constructed in situ on carbon foam (CF) to construct NiO@CF/OD composite phase change materials (CPCMs). The synthesis mechanism, microstructures, thermal management capability, and photothermal conversion of NiO@CF/OD CPCMs were systematically studied. Additionally, the collaborative enhancement effects of CF and multiform NiO nanowalls on the thermal properties of OD PCMs were also investigated. NiO@CF not only maintains the porous 3D network structure of CF, but also effectively prevents the aggregation of NiO nanosheets. The chemical structures of NiO@CF/OD CPCMs were analyzed using XRD and FTIR spectroscopy. When combined with CF and NiO nanosheets, OD has high compatibility with NiO@CF. The thermal conductivity of NiO@CF/OD-L CPCMs was 1.12 W/m·K, which is 366.7% higher than that of OD. The improvement in thermal conductivity of CPCMs was theoretically analyzed according to the Debye model. NiO@CF/OD-L CPCMs have a photothermal conversion efficiency up to 77.6%. This article provided a theoretical basis for the optimal design and performance prediction of thermal storage materials and systems.

Nanoparticle transport in partially saturated porous media: Attachment at fluid interfaces

Like the solid-water interface (SWI), air-water and oil-water interfaces (AWI and OWI) also act as collectors for nano-sized particles in porous media. The attachment of hydrophobic nanoparticles, which is often favorable and irreversible, is of particular interest because the transport and retention of such particles is closely linked to the fate of nanoplastics in unsaturated subsurface environments and the success of nanoremediation practices. Here, we show how a pore-network model (PNM) can be used to upscale the kinetics and extent of irreversible nanoparticle attachment at a single fluid-fluid interface under conditions of advection and dispersion in a sphere packing. By focusing on a trapped (immobile) non-wetting phase, we highlight a fundamental difference between the single-collector contact efficiency of AWI/OWI and SWI. Namely, AWI/OWI collectors, which are largely by-passed by the flowing aqueous phase, are exposed to a hydrodynamic environment dominated by diffusion. This difference has profound implications for the modelling of nanoparticle transport in porous media at the continuum (Darcy) scale. This study reveals the potential of pore network modelling as an essential complement to continuum models for upscaling the behavior of nanocolloids in porous media.

Magnetic carbon composites derived from biomass with excellent microwave absorption capacity

It is well known that magnetic iron oxide (Fe3O4) and carbon-based materials are good microwave absorbing materials. However, the frequency bands in which Fe3O4 absorbs electromagnetic waves are usually concentrated in the low-frequency region, whereas carbon materials are in the high-frequency region. Therefore, this study aims to deal with the limitation of the absorption bands of these two substances. In this work, this Fe3O4/C composite with high performance microwave absorption was successfully adoption of hydrothermal-calcination process using mangosteen shells as a biomass carbon material, and with a thickness of 1.97 mm, the optimal reflection loss of the sample can reach −67.49 dB, and the frequency band that can be absorbed is 4.32 GHz. The interface polarization, dipolar polarization and eddy current loss in Fe3O4 and carbon materials produce synergistic effects, and the porous conductive network increases the electromagnetic wave transmission path and generates conductive losses, which results in composites with excellent electromagnetic wave absorption properties. The findings indicated that a composite compound of Fe3O4 and carbon-based material was successfully synthesized by hydrothermal method and obtained a materials with outstanding electromagnetic wave absorption properties and high absorption bandwidth.

Reshaping and enzymatic activity may allow viruses to move through the mucus.

Filamentous viruses like influenza and torovirus often display systematic bends and arcs of mysterious physical origin. We propose that such viruses undergo an instability from a cylindrically symmetric to a toroidally curved state. This "toro-elastic" state emerges via spontaneous symmetry breaking under prestress due to short range spike protein interactions magnified by surface topography. Once surface stresses are sufficiently large, the filament buckles and the curved state constitutes a soft mode that can potentially propagate through the filament's material frame around a Mexican-hat-type potential. In the mucus of our airways, which constitutes a soft, porous 3D network, glycan chains are omnipresent and influenza's spike proteins are known to efficiently bind and cut them. We next show that such a non-equilibrium enzymatic reaction can induce spontaneous rotation of the curved state, leading to a whole body reshaping propulsion similar to - but different from - eukaryotic flagella and spirochetes.

Silk Fibroin-Based Scaffolds: Potential for Applications in Wound Healing

Chronic wounds, such as diabetic foot ulcers, pose significant challenges due to their prolonged inflammation state, slow vascularization, lack of supportive matrix, and frequent recurrence. Biocompatible materials like silk fibroin (SF) and collagen can be promising in chronic wound healing applications due to their biocompatibility, and ability to act as supporting matrix necessary for tissue regeneration. This study explores the development and characterization of SF-based biomaterials in various formats, including gels, lyophilized scaffolds, and films, by combining them with collagen (Col) and heparin (Hep) molecules that are known for the wound-healing properties. SF gels, films, and lyophilized scaffolds were characterized for water retention capacity, porosity, contact angle, and antibacterial properties. Curcumin-loaded films reported moderate wetting behavior but were brittle, thin and hard. Freeze-dried scaffolds possessed higher water retention capacity compared to the sonicated gels and films, and showed a porous network structure, while the fabricated SF gels disintegrated in water. SF with a chelating agent demonstrated mild antibacterial properties, which were retained when combined with Collagen peptides and Heparin. The antimicrobial effect was significantly enhanced when SF+Col+Hep was added with antimicrobial agents such as Gentamicin and Ceftriaxone. The study concludes that SF-based scaffolds, particularly those incorporating collagen peptides and heparin, can be leveraged for molecular delivery application towards wound healing. Future research should focus on improving mechanical properties, measuring release kinetics of heparin and other biomolecules from SF-based lyophilized scaffolds, and conducting in vivo studies to validate the therapeutic value.

Enhanced permeability prediction in porous media using particle swarm optimization with multi-source integration

Accurately and efficiently predicting the permeability of porous media is essential for addressing a wide range of hydrogeological issues. However, the complexity of porous media often limits the effectiveness of individual prediction methods. This study introduces a novel Particle Swarm Optimization-based Permeability Integrated Prediction model (PSO-PIP), which incorporates a particle swarm optimization algorithm enhanced with dynamic clustering and adaptive parameter tuning (KGPSO). The model integrates multi-source data from the Lattice Boltzmann Method (LBM), Pore Network Modeling (PNM), and Finite Difference Method (FDM). By assigning optimal weight coefficients to the outputs of these methods, the model minimizes deviations from actual values and enhances permeability prediction performance. Initially, the computational performances of the LBM, PNM, and FDM are comparatively analyzed on datasets consisting of sphere packings and real rock samples. It is observed that these methods exhibit computational biases in certain permeability ranges. The PSO-PIP model is proposed to combine the strengths of each computational approach and mitigate their limitations. The PSO-PIP model consistently produces predictions that are highly congruent with actual permeability values across all prediction intervals, significantly enhancing prediction accuracy. The outcomes of this study provide a new tool and perspective for the comprehensive, rapid, and accurate prediction of permeability in porous media.

Inhibition of efflorescence for fly ash-slag-steel slag based geopolymer: Pore network optimization and free alkali stabilization

The efflorescence problem is always an intractable problem for geopolymer. Silica fume (SF), nano-silica (NS), 5A zeolite (ZL) and nano-silica treated with silane (NST), were used to mitigate the efflorescence of fly ash (FA) - granulated blast furnace slag (GBFS) - steel slag (SS) based geopolymer. The effect of their dosages on the efflorescence was evaluated through accelerated efflorescing, leaching and unconfined compressive strength (UCS) tests. The inhibition mechanisms were explored by XRD, SEM, FTIR and MIP characterization. It revealed that SF and NS presented the most effective mitigating effect on efflorescence, with 9 % of SF and 2 % of NS totally inhibiting efflorescence and improving the compressive strength, and ZL and NST also alleviated the efflorescence at appropriate contents. Optimizing pore network and stabilizing free alkali were found to be the most important aspects for inhibiting efflorescence. The SF and NS worked efficiently in both two ways, which contained a large amount of dissolvable silicate that reacted with the excessive alkali to form C(N)-A-S-H and C-S-H gels. This filled and reduced the pores from 26 nm to less than 10 nm, and stabilized alkali with reduce the free w(Na+) by more than 50.45 %. On the other hand, ZL can solidify free alkali through the ion exchange property and fill pores due to its microaggregate nature, and NST reduced the efflorescence through blocking free alkali migration paths by hydrophobicity of the pores. These findings would guide the selection of appropriate methods to solve the efflorescence problem of geopolymers.

Co/CoOx–N–C bifunctional nanocatalyst derived from carbothermally optimized graphene networks with in-situ formed zeolitic imidazolate framework for high performance zinc-air batteries

Rechargeable zinc-air batteries are underpinned by high-performance and durable bifunctional oxygen electrocatalysts. Among the platinum-group metals (PGMs)-free catalysts, the redox-active cobalt-nitrogen-carbon (Co/CoOx–N–C) based materials are promising, however require further structural improvements. This work utilises extremely porous graphene networks (EGO) of hierarchical porosity to in-situ grow ZIF-67 nanocrystals extensively and homogeneously within the porous structure. A simple carbonization of nanoZIF-67@EGO not only generates finely dispersed redox capable Co/CoOx–N–C active sites with the help of residual oxygen functional groups of EGO, but also produces 2-3 dimensional hierarchical porous and conducting structure, readily facilitating high electrochemical surface area. This characteristic structure synergistically contributes to rapid charge and mass transfer rates along with high activity and stability for both ORR and OER. Here, it is worth mentioning that to produce equivalent catalyst material involving different graphitic or template supports requires prolonged and multi-step synthesis routes. The optimized catalyst delivers low potential difference of 0.86 V for bifucntional activity by offering superb ORR half-wave potential of 0.83 V vs RHE and limiting current density of 5.85 mA cm−2 in 0.1 M KOH electrolyte. Zinc-air battery exhibits peak power density of ∼175 mW cm−2 and specific capacity of ∼767 mAh g−1, along with durable cycling round trip efficiency of >63 % (correspond to low voltage gap of ∼0.74 V). These characteristics are better than numerous M–N–C based catalysts reported in the literature. This new strategy holds a great potential to boost the development of diverse MOFs and carbon-based electrocatalysts for a wide range of energy storage and conversion technologies.

Novel and stable carbon black/polyvinyl acetal aerogels efficiently harvesting solar energy for seawater desalination

A novel interfacial solar steam generators (ISSG) was prepared by a porous carbon black/polyvinyl acetal aerogel (CPA) with high light-absorbing hydrophilic properties, to achieve efficient solar-driven water evaporation and seawater desalination. The polyvinyl acetal was produced by the aldol condensation reaction of polyvinyl alcohol(PVA) and glutaraldehyde(GA). It was freeze-dried to create a hydrophilic porous structure that constructs an efficient hydrophilic channel. Carbon black (CB) exhibits high light absorption capabilities. Incident light undergoes multiple scattering within its porous network structure, effectively reducing reflected light energy loss and enabling efficient thermal conversion of sunlight. Benefited from its highly light-absorbing porous hydrophilic structure, CPA-40-3 evaporation rate achieves an impressive 3.23 kg·m−2·h−1 and an evaporation efficiency of 94 % under 1 sun irradiation, without obvious decay even during long-term use. Furthermore, CPA-40-3 demonstrates remarkable salt tolerance, the evaporation rate remains at 2.55 kg·m−2·h−1 although in simulated Dead Sea salt water under 1 sun irradiation. Compared to traditional ISSG, the CPA has advantages such as superior mechanical properties, prevention of surface salt precipitation, faster water supply, and a larger light absorption area. This design had tremendous promise for efficient solar desalination due to its extraordinarily high evaporation performance in high-salinity brine.

Porphyrin-based schiff-base and aminal nitrogen-rich porous organic polymers for capture of SO2 and CO2

Due to its serious hazards to human health and the environment, the deep removal of sulfur dioxide (SO2) has been of great significance. Thus, it is critical to develop high efficient SO2 capture and sequestration materials in gas purification process. Herein, we reported two novel prophyrin-based nitrogen-rich porous organic polymers (POPs), PrPOA-BP and PrPSN-BP, constructed through the simple catalyst-free condensation reaction. Owing to the strong affinity to SO2 from the conjugate-electron macrocycles structure of prophyrin and nitrogen-rich porous networks, also the high porous structure, these two POPs demonstrated excellent SO2 capture and separation performance with the adsorption uptakes up to 18.2 mmol g−1 (273 K, 1 bar), 13.3 mmol g−1 (298 K, 1 bar), 1.68 mmol g−1 (298 K, 0.01 bar). This very competitive performance has far exceeded most of the prior reported nanoporous materials. Meanwhile, the IAST selectivities of SO2/CO2 (10/90, v/v) could reach 107.8 and 72.0 at 273 and 298 K, 1 bar. This study represents a new type prophyrin-based POPs materials and confirms the intrinsic potential for high efficiency SO2 capture and sequestration.

Achieving efficient electromagnetic absorption in multifunctional carbon nanotube aerogels by manipulating radialized network structure

The rapid advancements in communication technology have greatly propelled the widespread applications of artificial intelligence (AI). While AI technology facilitates society, it also brings the unavoidable electromagnetic hazards and the issue of disposal of electronic plastic wastes. So, utilizing electronic plastic wastes to constructing carbon-based electromagnetic wave (EMW) absorption materials, are highly promising. However, how to use CNTs from plastic wastes to build good EMW absorption performance aerogels is a critical challenge. In this work, highly porous and well-interconnected network aerogels constructed by radialized CNT arrays are rationally designed under the guidance of grave-to-cradle strategy, exhibiting altered impedance matching and multiple EMW attenuation methods. Theoretical calculations suggest that a well-designed heterojunction interface structure can enhance the conductivity and interface polarization of CNTAs. The CNT aerogels (CNTAs) realize broad absorption bandwidth covering 8.48 GHz with a minimum reflection loss of −59.5 dB. Moreover, the radialized arrays network of CNTAs also endows it with electromagnetic protection, thermal management, self-cleaning, and air purification functions. These inspiring achievements of multifunctional CNTA-2 provides new help for the safe and stable promotion of the AI era.

Light-driven methanol-to-olefins catalysis over W18O49/SAPO-34 hierarchical nanocomposite with strong photothermal effect

Solar-light-driven photothermal catalysis attracts attention because of the significant energy savings and environmental friendliness compared with thermal catalysis. In the present work, W18O49/SAPO-34 composite materials with hierarchical pore networks were constructed by a simple hydrothermal method, and applied into photothermal catalysis for methanol-to-olefins transformation. In combination of the broaden light absorption of W18O49 and moderate acid site of SAPO-34, the W18O49/SAPO-34 composite showed a rapid temperature rise on the surface of the catalysts due to the strong photo-to-thermal effect of W18O49. Methanol conversion of ∼ 90 % and ethylene selectivity of ∼ 60 % were achieved for the optimized W18O49/SAPO-34 catalyst, much higher than that of bare W18O49 and SAPO-34. The excellent methanol dehydration performance was attributed to the strong plasmonic absorption in the visible and near infrared light, the efficient photothermal conversion effect by localized plasmon heating on the W18O49 nanorods, and synergistic catalysis between W18O49 and SAPO-34. This photothermal catalyst showed great potential in the industrial applications of photocatalytic methanol-to-olefins conversion.

Maneuvering the mineralization of self-assembled peptide nanofibers for designing mechanically-stiffened self-healable composites toward bone-mimetic ECM.

Extracellular matrix (ECM) elasticity remains a crucial parameter to determine cell-material interactions (viz. adhesion, growth, and differentiation), cellular communication, and migration that are essential to tissue repair and regeneration. Supramolecular peptide hydrogels with their 3-dimensional porous network and tuneable mechanical properties have emerged as an excellent class of ECM-mimetic biomaterials with relevant dynamic attributes and bioactivity. Here, we demonstrate the design of minimalist amyloid-inspired peptide amphiphiles, CnPA (n = 6, 8, 10, 12) with tuneable peptide nanostructures that are efficiently biomineralized and cross-linked using bioactive silicates. Such hydrogel composites, CnBG exhibit excellent mechanical attributes and possess excellent self-healing abilities and collagen-like strain-stiffening ability as desired for bone ECM mimetic scaffold. The composites exhibited the formation of a hydroxyapatite mineral phase upon incubation in a simulated body fluid that rendered mechanical stiffness akin to the hydroxyapatite-bridged collagen fibers to match the bone tissue elasticity eventually. In a nutshell, peptide nanostructure-guided temporal effects and mechanical attributes demonstrate C8BG to be an optimal composite. Finally, such constructs feature the potential for adhesion, proliferation of U2OS cells, high alkaline phosphatase activity, and osteoconductivity.

High performance flexible phase change hydrogel applied to thermal management of new cigarette device

To address the thermal management challenges of new heat-not-burn (HNB) cigarette devices, this study aims to enhance overall energy conversion efficiency while maintaining unchanged battery capacity. The goal is to minimize heat dissipation and reduce the temperature of the device's housing that contacts the user. In this research, CaCl2·6H2O (CCH) was selected as the phase change material (PCM), and a polyacrylamide (PAM) phase change hydrogel encapsulating CCH was prepared via in-situ polymerization. Additionally, konjac glucomannan (KGM) was incorporated into the three-dimensional network structure of PAM through hydrogen bonding to promote the formation of a porous gel structure. CNTs-CuO composites, featuring in-situ generated CuO nanoparticles on carbon nanotubes (CNTs), were synthesized using a microwave hydrothermal method and employed to enhance the thermal conductivity of the phase change hydrogel.This study demonstrates that the three-dimensional porous network structure of the hydrogel not only provides effective encapsulation protection for CCH and maintains high latent heat (144.9 J/g), but also imparts excellent flexibility and stability to the composites. The incorporation of CNTs-CuO composites introduces efficient heat transfer channels, significantly increasing the thermal conductivity of the hydrogels by approximately 37 % (0.687 W·m−1·K−1). Moreover, the hydrogel composites exhibit exceptional temperature regulation properties.The innovative design and preparation of these hydrated salt-based flexible hydrogel composites offer a novel approach in the fields of thermal management and energy storage. This material demonstrates practical applications not only in HNB devices but also in various thermal management systems, such as wearable electronics, battery thermal management, and electronic device cooling. Furthermore, its application in energy storage systems, including thermal energy storage units and smart textiles, underscores its broad applicability and significance.

The collaborative effect of Ni3S2-NiO heterojunction and porous carbon network modified lithium-sulfur battery separator for effectively inhibiting polysulfides shuttle

As an important part of lithium-sulfur battery (LSB), separator not only provides ion transport channel but also plays a key role in ensuring battery safety. However, the aperture of the commercial separator polypropylene (PP) is relatively large, which cannot effectively inhibit the migration of polysulfides generated during the charging and discharging process between the positive and negative electrodes, resulting in a decrease in the cycle stability of LSB. In this work, a modified LSB separator Ni3S2-NiO@AC-4@PP is designed, which is anchored by Ni3S2-NiO heterojunction on volcanic rock-like three-dimensional porous carbon network (AC) as the functional interlayer. The AC possesses a large specific surface area and excellent electrical conductivity, creating sufficient space for the physical and chemical adsorption of insoluble polysulfides. The Ni3S2-NiO heterojunction is embedded and attached to the AC, which helps to hinder the diffusion of polysulfides and accelerate the redox reaction. It is also confirmed by density functional theory (DFT) calculation that Ni3S2-NiO heterojunction inhibited the shuttle of polysulfides through the adsorption capacity of NiO and the catalytic activity of Ni3S2. Thus, the Ni3S2-NiO@AC-4@PP battery exhibits an elevated initial specific capacity of 1027.8 mAh g−1 at 0.2C, maintaining long-term stability after 200 cycles with the capacity retention rate of 81.4 %. At the higher current density (2C), Ni3S2-NiO@AC@PP battery demonstrates durable cycle with the capacity retention rate of 91.3 %. This study proposes a new feasible strategy to obtain high-performance, low-cost modified separators by designing functional interlayers with excellent adsorption and catalytic properties.

Scalable pilot production of highly efficient 5-ply respiratory masks enhanced by bacterial cellulose nanofibers

This study presents the pilot-scale production of highly efficient real respiratory masks enhanced by bacterial cellulose nanofibers (BCNFs). The BCNFs suspension was deposited onto tissue paper substrates using fog spray technique with three BCNFs grammage levels of 0.5, 1, and 2 g/m2, followed by freeze drying. Also, two continuous and batch welding processes have been used to construct the core structure of the masks. Field emission scanning electron microscopy (FE-SEM) confirmed the uniform distribution and size of fog-sprayed BCNFs and their pore networks. With increase in BCNFs grammage, the adsorption efficiency of masks increased in both continuous and batch production methods. The mask produced through batch processing showed the highest efficiency of 99.2 % (N99) for the particulate matter of 0.3 μm, while the maximum corresponding efficiency value in continuous processing was 95.4 % (N95). The pressure drops of the masks increased with the increase in BCNFs grammage in both methods. The maximum pressure drops of N95 and N99 masks obtained were 112 ± 10 Pa and 128 ± 8 Pa, respectively. Notably, the filtration efficacy of masks was preserved when subjected to relative humidity fluctuations ranging from 30 % to 70 %. The successful findings of this study offer significant promise for future air filtration applications.

A Breathable and Strain‐Insensitive Multi‐Layered E‐Skin Patch for Digital Healthcare Wearables

AbstractIn this study, a breathable and strain‐insensitive multi‐layered electronic skin (e‐skin) capable of real‐time detection and distinction of electrocardiogram (ECG) signals, temperature, and skin hydration is developed. Leveraging a scalable benchtop method, sensing elements are transferred onto porous and hydrophobic substrates, followed by multi‐layer stacking to enable multimodal sensing. The sensing elements, a combination of carbon nanotube and nanoporous carbon (CNT@NPC) ink, are applied using strain‐insensitive patterned masks, then spray‐coated with styrene–ethylene–butylene–styrene (SEBS) to create a hierarchical porous network through phase separation. The CNT@NPC networks exhibit an improvement in strain insensitivity with active sensing capabilities due to their adaptable molecular tuning capacity and exceptional electrical conductivity. The porous SEBS substrate offers strong bonding with CNT@NPC attributed to the π–π interactions and high kinetic energy dispersion from spray coating allowing effective transfer. This unique design facilitates breathability, and miniaturization that minimizes the interference between different sensing modalities, ensuring accurate and reliable data acquisition. The breathability (3.49 mg cm−2 h−1) and the non‐smearing nature of the multi‐layered e‐skin enables simultaneous monitoring of temperature (0.198% °C−1), skin hydration (relative humidity = 0.77% %−1), and ECG (26 ± 1 dB) with continuous data transmission to a remote smartphone interface.

A facile way to fabricate a thrombin immobilized composite sponge with dual hemostatic effects for acute hemorrhage control

Uncontrolled bleeding and excessive blood loss stand as the leading causes of death in complex surgeries, civilian traumas, and military operations. Sponges have been used for developing efficiency hemostats, but most commonly used hemostatic sponges possess only one single coagulation mechanism or lack inherent blood clotting ability. Herein, we proposed simple yet innovative approaches for creating novel hemostatic composite sponges with dual hemostatic effects. Bacterial cellulose (BC) was first introduced into polyvinyl alcohol (PVA) matrix to develop a BC/PVA (CP) sponge featuring a unique cellulose-embedded porous network structure and desirable properties. Subsequently, thrombin was immobilized on CP through an easy method that combines physical adsorption and covalent binding to fabricate thrombin-carrying CP (TCP) composite sponges. The resulting composites boasted a highly porous structure, outstanding liquid-absorption capacity, low hemolysis rate, and superior biocompatibility. In vitro clotting tests revealed that TCP displayed potent coagulation capabilities, a rapid blood absorption rate, and the ability to stimulate and activate blood components along with the coagulation cascade. In vivo hemostatic assessments further confirmed that TCP offered high hemostatic efficiency and multifaceted hemostatic effects, making it suitable for the management of acute and severe bleeding.

Critical assessment of the validity of quasi-static pore network modeling in the application of underground hydrogen storage

This study explores the suitability of quasi-static pore-network modeling for simulating the transport of hydrogen in networks with box-shaped pores and square cylinder throats. The dynamic pore-network modeling results are compared with quasi-static pore-network modeling, and a good agreement is observed when the simulations reach steady-state, for a capillary number of Nc≤10−7. This finding suggests that the quasi-static approach can be used as a reliable and efficient method for studying hydrogen transport in similar networks.