Photogenerated Charge Carriers Research Articles

Tm3+/Yb3+:NaGdF4 nanoparticles decorated g-C3N4/BiOBr0.75I0.25 multicomponent heterostructure: Structural, optical properties and UV–Visible-NIR responsive photocatalytic degradation of Rhodamine B and reduction of Cr(VI)

A wide solar spectral range responsive multicomponent heterostructure photocatalyst NGT/g-C3N4/BiOBr0.75I0.25 was successfully synthesized and used for the UV–visible-NIR photodegradation of the dye Rhodamine B and photoreduction of highly toxic hexavalent chromium ions. Our study shows that the heterostructure overcomes the drawbacks of limited visible-light absorption and fast charge recombination of g-C3N4. Herein, the incorporation of BiOBr0.75I0.25 extends the absorption in the visible region and endorses the separation rate of photogenerated charge carriers. Additionally, the upconversion nanoparticles NaGdF4: Tm/Yb (NGT) with its higher infrared light absorption capacity and characteristic emission spectral overlapping with absorption range of g-C3N4/BiOBr0.75I0.25 nanocomposite, further facilitates the photocatalytic activity of the NGT/g-C3N4/BiOBr0.75I0.25 heterostructured nanocomposite. Extensive structural, morphological, and compositional analysis was done using XRD, TEM, SEM, FE-SEM, XPS, and FTIR measurements. The PL emission, time-resolved decay, and electrochemical impedance spectroscopy were used to probe the separation rate of photogenerated electron-hole pairs and efficient energy transfer in NGT/g-C3N4/BiOBr0.75I0.25 heterostructured nanocomposite. The possible photocatalytic degradation mechanism was comprehensively proposed through a combination of UV–Vis absorption, Mott Schottky, and scavenger test analysis. The photodegradation efficiency of the heterojunction was 98 %, which is much higher than the bare g-C3N4 (74 %). Moreover, the heterostructure exhibited excellent long-term reusability, maintaining the photodegradation efficiency of 97.02 % even after four consecutive degradation cycles, establishing it as a preferable material for photocatalytic dye degradation. Additionally, NGT/g-C3N4/BiOBr0.75I0.25 heterostructured nanocomposite also demonstated better performance for the photoreduction of Cr(VI) to Cr(III), achieving photocatalytic efficiency of 98.86 % under acidic condition.

Donor-Acceptor characteristic g-C3N4 hollow nanospheres heterojunctions for efficient photocatalytic uranium reduction

Using photocatalysis to extract uranium from aqueous solution is a promising technique for the remediation of radioactive wastewater. This article reports the synthesis of hollow spherical g-C3N4 (HCN) via a template method, and its subsequent modification by PEDOT:PSS (PTPS) to form a donor-acceptor (D-A) heterojunction photocatalyst (PTPS@HCN). The well-designed hollow structure and the incorporation of PTPS enhanced the visible light absorption, effectively driving the separation and transfer of photogenerated charge carriers. Moreover, the theoretical calculation reveals that the electronic excitation model of PTPS@HCN exhibits a distinct charge-transfer excitation characteristic. As a result, PTPS@HCN could efficiently remove 98.6 % of U(VI) after 90 min irradiation, which was 6.4 times higher than that of the pristine HCN. This study offers a new perspective for designing D-A organic photocatalysts for the photocatalytic separation of uranium.

Molecularly Tunable Heterostructured Co-Polymers Containing Electron-Deficient and -Rich Moieties for Visible-Light and Sacrificial-Agent-Free H2O2 Photosynthesis.

As an alternative to hydrogen peroxide (H2O2) production by complex anthraquinone oxidation process, photosynthesis of H2O2 from water and oxygen without sacrificial agents is highly demanded. Herein, a covalently connected molecular heterostructure is synthesized via sequential C-H arylation and Knoevenagel polymerization reactions for visible-light and sacrificial-agent-free H2O2 synthesis. The subsequent copolymerization of the electron-deficient benzodithiophene-4,8-dione (BTD) and the electron-rich biphenyl (B) and p-phenylenediacetonitrile (CN) not only expands the π-conjugated domain but also increases the molecular dipole moment, which largely promotes the separation and transfer of the photoinduced charge carriers. The optimal heterostructured BTDB-CN0.2 manifested an impressive photocatalytic H2O2 production rate of 1920 μmol g-1 h-1, which is 2.2 and 11.6 times that of BTDB and BTDCN. As revealed by the femtosecond transient absorption (fs-TA) and theoretical calculations, the linkage serves as a channel for the rapid transfer of photogenerated charge carriers, enhancing the photocatalytic efficiency. Further, in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) uncovers that the oxygen reduction reaction occurs through the step one-electron pathway and the mutual conversion between C=O and C-OH with the anchoring of H+ during the catalysis favored the formation of H2O2. This work provides a novel perspective for the design of efficient organic photocatalysts.

A Facile Strategy for the Preparation of N-Doped TiO2 with Oxygen Vacancy via the Annealing Treatment with Urea.

Although titanium dioxide (TiO2) has a wide range of potential applications, the photocatalytic performance of TiO2 is limited by both its limited photoresponse range and fast recombination of the photogenerated charge carriers. In this work, the preparation of nitrogen (N)-doped TiO2 accompanied by the introduction of oxygen vacancy (Vo) has been achieved via a facile annealing treatment with urea as the N source. During the annealing treatment, the presence of urea not only realizes the N-doping of TiO2 but also creates Vo in N-doped TiO2 (N-TiO2), which is also suitable for commercial TiO2 (P25). Unexpectedly, the annealing treatment-induced decrease in the specific surface area of N-TiO2 is inhibited by the N-doping and, thus, more active sites are maintained. Therefore, both the N-doping and formation of Vo as well as the increased active sites contribute to the excellent photocatalytic performance of N-TiO2 under visible light irradiation. Our work offers a facile strategy for the preparation of N-TiO2 with Vo via the annealing treatment with urea.

Dual Channel H2O2 Photosynthesis in Pure Water over S-Scheme Heterojunction Cs3PMo12/CC Boosted by Proton and Electron Reservoirs.

Dual channel photo-driven H2O2 production in pure water on small-scale on-site setups is a promising strategy to provide low-concentrated H2O2 whenever needed. This process suffers, however, strongly from the fast recombination of photo-generated charge carriers and the sluggish oxidation process. Here, insoluble Keggin-type cesium phosphomolybdate Cs3PMo12O40 (abbreviated to Cs3PMo12) is introduced to carbonized cellulose (CC) to construct S-scheme heterojunction Cs3PMo12/CC. Dual channel H2O2 photosynthesis from both H2O oxidation and O2 reduction in pure water has been thus achieved with the production rate of 20.1mmolL-1gcat. -1h-1, apparent quantum yield (AQY) of 2.1% and solar-to-chemical conversion (SCC) efficiency of 0.050%. H2O2 accumulative concentration reaches 4.9mmol L-1. This high photocatalytic activity is guaranteed by unique features of Cs3PMo12/CC, namely, S-scheme heterojunction, electron reservoir, and proton reservoir. The former two enhance the separation of photo-generated charge carriers, while the latter speeds up the torpid oxidation process. In situ experiments reveal that H2O2 is formed via successive single-electron transfer in both channels. In real practice, exposing the reaction system under natural sunlight outdoors successfully results in 0.24mmol L-1 H2O2. This work provides a key practical strategy for designing photocatalysts in modulating redox half-reactions in photosynthesis.

Photocatalytic degradation of p-aminobenzoic acid on N-biomass charcoal etched with Fe-Al-bilayer hydroxide: New insights through spectroscopic investigation

We investigated the photocatalytic property of etched iron‑aluminum layered double hydroxide (LDH) composites using urea-modified biochar (N-BC) carrier to degrade para-aminobenzoic acid (PABA), a refractory organic pollutant. The prepared FeAl-LDH@FeSx-N-BC composite exhibited excellent photocatalytic performance, attributed to the enhanced photogenerated charge-carrier separation by the etched LDH and the improved comparative surface areas by the doped N-BC. The composite photocatalytically degraded 96 % of PABA. The performance was affected by solute concentration, pH and photocatalyst dose. Adding p-benzoquinone and EDTA-2Na significantly decreased the degradation rate, suggesting that superoxide radicals and holes were co-involved in PABA degradation. The excellent PABA removal efficiency was consistent for three consecutive runs. The samples' reactive oxygen species was confirmed, as electron paramagnetic reverberation explained the photodegradation mechanism. Under xenon lamp irradiation, two PABA photocatalytic degradation pathways were proposed using Liquid Chromatograph Mass Spectrometer (LCMS) and density functional theory. As expected, FeAl-LDH@FeSx-N-BC showed excellent photocatalytic performance, expanding a new direction and possibility for future photocatalytic treatment of water pollutants.

Enhanced Hydrogen Evolution in Porous and Hybrid g‐C3N4/Pt‐PVDF Electrospun Membranes via Piezoelectricity from Water Flow Energy

AbstractInspired from seaweed swayed by waves, the enhanced hydrogen evolution is realized in porous and hybrid g‐C3N4/Pt‐PVDF electrospun membranes via piezoelectricity from water flow energy. The membranes are fabricated by dispersing g‐C3N4/Pt into the mixed solution of PVDF and PEO, followed by electrospinning and selective removal of PEO. By changing the PEO amount, the pore size in nanofibers is adjusted. Due to the hydrogen bonding between g‐C3N4/Pt and PVDF, the β phase of PVDF is increased, beneficial for the piezoelectricity performance. When the electrospun membranes are exposed to water flow, an additional potential field is triggered due to the deformation of PVDF. It not only eases the photogeneration of charge carriers from g‐C3N4/Pt but also hinders their recombination. The prolonged lifetime significantly improves the photocatalytic water splitting of g‐C3N4/Pt under visible light. The hydrogen evolution in the electrospun membranes (PVDF to PEO = 4:1) is profoundly improved to 9 278 µmol h−1 g−1, almost doubled to the pure g‐C3N4/Pt nanosheets (5 220 µmol h−1 g−1). Therefore, the seaweed‐inspired electrospun membrane is a promising strategy for the efficiently photocatalytic water splitting via g‐C3N4 in an aqueous environment, such as a natural sea and lake, by the piezoelectricity gained from the water flow energy.

Enhanced Light Absorption and Photo-Generated Charge Separation Efficiency for Boosting Photocatalytic H2 Evolution through TiO2 Quantum Dots with N-Doping and Concomitant Oxygen Vacancy.

Low-range light absorption and rapid recombination of photo-generated charge carriers have prevented the occurrence of effective and applicable photocatalysis for decades. Quantum dots (QDs) offer a solution due to their size-controlled photon properties and charge separation capabilities. Herein, well-dispersed interstitial nitrogen-doped TiO2 QDs with stable oxygen vacancies (N-TiO2-x-VO) are fabricated by using a low-temperature, annealing-assisted hydrothermal method. Remarkably, electrostatic repulsion prevented aggregation arising from negative charges accumulated in situ on the surface of N-TiO2-x-VO, enabling complete solar spectrum utilization (200-800 nm) with a 2.5 eV bandgap. Enhanced UV-vis photocatalytic H2 evolution rate (HER) reached2757µmol g-1 h-1, 41.6 times higher than commercial TiO2 (66µmol g-1 h-1). Strikingly, under visible light, HER rate was 189µmol g-1 h-1. Experimental and simulated studies of mechanisms reveal that VO can serve as an electron reservoir of photo-generated charge carriers on N-doped active sites, and consequently, enhance the separation rate of exciton pairs. Moreover, the negative free energy (-0.35 V) indicates more favorable thermodynamics for HER as compared with bulk TiO2 (0.66 V). This research work paves a new way of developing efficient photocatalytic strategies of HER that are applicable in the sustainable carbon-zero energy supply.

Boosting photocatalytic activity in ternary lamellar hierarchical structured ZnFe2O4/polymeric carbon nitride by constructing an electronic bridge

Photocatalytic technology is one of the ideal approaches for clean energy production and environmental pollution control in the future. However, the rapid recombination of photo-generated charge carriers is a bottleneck problem of low solar energy conversion efficiency. Herein, a magnetic ZnFe2O4/Pt/polymeric carbon nitride (PCN) semiconductor catalyst is designed and prepared for high-performance photocatalytic hydrogen production reaction and photocatalytic degradation rate of RhB. It exhibits 339.31 μmol·g−1·h−1 hydrogen production rate and 96.08 % photocatalytic degradation rate of RhB within 120 min under visible light. The introduction of Pt, constructing an electronic bridge, accelerated the transfer of photo-generated carriers, meanwhile, the smaller band gap of the ternary composites enabled the generation of more photo-generated electrons. The internal electric field accelerated the accumulation of electrons and holes in the conduction band of ZnFe2O4 and valence band of PCN, thus photocatalytic activity is greatly enhanced. The electron-hole separation is also improved and the transport of photo-generated electrons is facilitated by the special structure of the heterojunction and the unique morphology of PCN. In addition, the used catalyst can be recovered through magnetic fields, and this magnetic catalytic system has great application prospects in the fields of photocatalytic hydrogen production and pollutant degradation.

Short-Wave Infrared Colloidal QD Photodetector with Nanosecond Response Times Enabled by Ultrathin Absorber Layers.

Ultrafast short-wavelength infrared (SWIR) photodetection is of great interest for emerging automated vision and spatial mapping technologies. Colloidal quantum dots (QDs) stand out for SWIR photodetection compared to epitaxial (In,Ga)As or (Hg,Cd)Te semiconductors by their combining a size-tunable bandgap and a suitability for cost-effective, solution-based processing. However, achieving ultrafast, nanosecond-level response time has remained an outstanding challenge for QD-based SWIR photodiodes (QDPDs). Here, record 4ns response time in PbS-based QDPDs that operate at SWIR wavelengths is reported, a result reaching the requirement of SWIR light detection and ranging based on colloidal QDs. These ultrafast QDPDs combine a thin active layer to reduce the carrier transport time and a small area to inhibit slow capacitive discharging. By implementing a concentration gradient ligand exchange method, high-quality p-n junctions are fabricated in these ultrathin QDPDs. Moreover, these ultrathin QDPDs attain an external quantum efficiency of 42% at 1330nm, due to a 2.5-fold enhanced light absorption through the formation of a Fabry-Perot cavity within the QDPD and the highly efficient extraction (98%) of photogenerated charge carriers. Based on these results, it is estimated that a further increase of the charge-carrier mobility can lead to PbS QDPDs with sub-nanosecond response time.

Manufacturing porous BaTaO2N nanosheet via nitridation of a novel oxyhalide precursor for boosted photocatalytic water oxidation reaction

BaTaO2N (BTON) with a generous adsorption edge of ca. 660 nm and high theoretical solar-to-hydrogen conversion efficiency of ca. 20.6% has been extensively investigated for photocatalytic water splitting. In this study, we have successfully prepared a porous BTON nanosheet via employing Ba2Bi3Ta2O11Cl (BBTOC) oxyhalide as a novel nitridation precursor. The oxygen evolution rate of the BTON nanosheet is 108 μmol·h−1, which is three times higher than that of BTON (25.9 μmol·h−1) prepared by conventional solid-state method. The successful construction of porous BTON nanosheet is due to the structural transformation of BBTOC nanosheet precursor and facile evaporation of Bi and Cl elements. The porous nanosheet morphology of BTON can not only promote the transfer of photogenerated charge carriers but also provide abundant reaction sites for the oxygen evolution reaction. This work demonstrates a novel and efficient strategy for preparing oxynitride for efficient solar energy conversion.

Zr dopant acting shallow donor and active site in CdS lattice for co-catalyst free photocatalytic H2 evolution

Hydrogen evolution by photocatalysis shows great potential in solar energy conversion process and thus has become an active field of research. Separation efficiency of photogenerated carriers, light absorption and surface reaction are the dominant aspects that affect the photocatalytic hydrogen evolution. Creating traps to prolong the lifetime of photogenerated charge carriers has been widely used but may be considered detrimental if they lead to recombination process of the photogenerated charge carriers. Herein, we design a kind of efficient atomic substitution strategy to create shallow donor for highly efficient hydrogen evolution reaction. The photocatalytic hydrogen evolution reaction rate reaches 3766.9 μmol h−1 g−1, which is about 2.98 times higher of pure CdS. The injected foreign atoms (Zr) not only reduce bandgap to extend light absorption but also generate shallow trap level to reduce recombination of photogenerated carriers. Moreover, the introduced atoms could downshift Fermi level to supply more carriers and act the role as active center to reduce Gibbs free energy, leading to the enhanced hydrogen generation rate and superior stability. This report offers new enlightenment into designing noble-metal free photocatalysts with extraordinary catalytic performance and excellent stability.

Interface Regulation of Bi3TiNbO9/Rh Photocatalysts by Introducing Ultrathin Heterolayer to Enhance Overall Water Splitting

AbstractAurivillius compounds‐based photocatalysts have attracted extensive interest largely due to their ferroelectric properties and modifiable characteristics arising from the alternate stacking of structural units. However, the interfacial Schottky barrier between such semiconducting compounds as light absorbers and metallic cocatalysts for hydrogen evolution restrains the transfer of photogenerated electrons, resulting in low photocatalytic overall water splitting activity and stability. Here, an anions‐induced surface structure transformation strategy is employed to modulate the interface structure between Bi3TiNbO9 as a typical Aurivillius compound and the cocatalyst Rh by in situ growing ultrathin Bi2MoO6 heterolayer on the surface of Bi3TiNbO9 nanosheets. The introduction of Bi2MoO6 heterolayer lowers the energy barrier near the Bi3TiNbO9 surface, which can facilitate the transfer of the photogenerated electrons from bulk to surface and thus the reduction of Rh cocatalyst for highly active hydrogen production. Compared with the Bi3TiNbO9‐Rh photocatalyst, the proportion of low‐valence metallic Rh0 in Bi2MoO6 heterolayer‐modified Bi3TiNbO9‐Rh (Bi3TiNbO9‐Bi2MoO6‐Rh) is improved by 7.76%, giving rise to a photocatalytic overall water splitting activity enhancement by a factor of 4.74. This strategy emphasizes the importance of interface regulation in promoting the transfer of photogenerated charge carriers in Aurivillius‐type photocatalysts, providing an effective pathway for designing and fabricating high‐performance photocatalysts.

Photo-induced in-situ synthesis of Cu2O@C nanocomposite for efficient photocatalytic evolution of hydrogen

Cuprous oxide (Cu2O) is an ideal visible light catalyst owing to its narrow band gap, environmental benignity and abundant storage; however, the fast recombination of photogenerated charge carriers and poor stability of Cu2O has impeded its application in photocatalysis. Herein, we demonstrate that Cu2O@C nanocomposite can spontaneously evolve from a methanol aqueous solution containing cupric ions under the induction of irradiation. Compared with the traditional carbon coating method, the Cu2O@C nanocomposite obtained by the photo-induced in-situ synthesis can reserve superior original characteristics of the semiconductor under mild reaction conditions, promote the charge transfer and enhance the separation efficiency of charge carriers; in addition, the carbon shells can also effectively prevent Cu2O from photo-corrosion. As a result, the Cu2O@C nanocomposite exhibits excellent photocatalytic activity in the hydrogen evolution in comparison with the Cu2O particles; the H2 evolution rate over the Cu2O@C nanocomposite reaches 1.28 mmol/(g·h) under visible light, compared with the value of 0.065 mmol/(g·h) over Cu2O. Moreover, the Cu2O@C nanocomposite displays good cycle stability, viz., without any deactivation in the catalytic activity after five cycles.

Enhanced photocatalytic hydrogen generation using UiO-66(Zr) MOF with tailored modifications: A review

The utilization of UiO-66 MOF-based photocatalytic materials has achieved significant attention for their potential in hydrogen generation, owing to their remarkable stability and porous crystalline structure. Recent studies have disclosed enhanced light absorption capabilities in UiO-66 through both pre and post-synthetic modifications. These modifications also play a significant role in mitigating the recombination of photogenerated charge carriers by facilitating electron transfer in hybrid or derived materials. Designing of MOF-based modified improved photocatalyst includes, integration with other low band gap semiconductors, incorporation of noble metals as co-catalysts, surface engineering, inclusion of defects or introduction of heteroatom in the framework. MOF-COF hybridization, dye sensitization etc., further reinforced photocatalytic hydrogen yield. The above-mentioned comprehensive investigations have researched into aspects such as morphology, hydrogen generation efficiency, and the underlying mechanisms. It reveals that the creation of heterojunctions at interface channelizes the separation and smooth flow of electrons resulting in suppression of recombination reaction and favorable photocatalytic properties. The synergy between the components often results in enhanced performance. The present article provides a comprehensive review of modified UiO-66 MOF-based materials investigated for photocatalytic hydrogen generation.

Extremely interfacial bonding and photocatalytic environmental remediation on amouphous-TiO2/g-C3N4 heterojunctions by mechanochemical synthesis

TiO2/g-C3N4 composites have emerged as the most potent alternative for green photocatalysis, but are plagued by low photoactivity due to poor interfacial bonding. Herein, we report a straightforward mechanical ball milling method to fabricate an amorphous TiO2/g-C3N4 heterojunction. EPR, XPS and XAFS are used to prove that the N atoms of g-C3N4 was successfully doped into the crystal lattice of Am-TiO2 and formed typical Ti···N structure. The obtained 30-AT/CN (30 wt% g-C3N4) composites can form more heterojunction interfacial bonds and extremely improve the separation of charge carriers, showing superior photocatalytic reduction performance of perrhenate (non-radioactive chemical substitute for pertechnetate) and higher photochemical degradation rate of rhodamine B than the bulk counterpart. The material has a progressive Z-scheme heterojunction (S-scheme heterojunction), which increases the transfer ability and prolongs the lifetime of the photogenerated charge carriers. These results suggest a wide range of applications in the preparation method of heterojunction photocatalysts that are potential candidates for environmental remediation.

Enhanced photovoltaic performance of dye sensitized solar cells using cesium bromide modified TiO2 electron transport layer

TiO2 is one of the most widely explored materials as an electron transport layer (ETL) in dye sensitized solar cells (DSSCs) due to its excellent physical and chemical properties. However, recombination at the device's interface slackens the charge carrier movement, adversely affecting their device performance. Rapid extraction of photogenerated charge carriers plays a vital role in developing high efficiency DSSCs. The conduction band alignment of TiO2 ETL and N719 dye light absorber plays a crucial role in charge carrier dynamics of DSSCs. Herein, the band structure of TiO2 ETL is finely tuned by the incorporation of cesium bromide (CsBr). At the optimal concentration (0.4 Wt. %), DSSCs achieved the best power conversion efficiency (PCE) of 9.28 % compared to 7.61 % for pristine TiO2. The modified TiO2–CsBr ETL induced a negative shift in flat band potential (Vfb) from −0.46 to −0.50 V, which improved the open circuit voltage (VOC), its work function (ɸ) from −4.71 to −3.75 eV and increased conduction band minimum (CBM) from −3.58 to −2.42 eV. CsBr incorporation increased electron density in TiO2 matrix, indicating the suppression of trap state and significantly improved the overall photovoltaic performance of DSSCs.

Construction of Au quantum dots/nitrogen-defect-enriched graphite carbon nitride heterostructure via photo-deposition towards enhanced nitric oxide photooxidation

The challenge of mitigating pollution stemming from industrial exhaust emissions is a pressing issue in both academia and industry. This study presents the successful synthesis of nitrogen-defect-enriched graphite carbon nitride (g-C3N4) using a two-step calcination technique. Furthermore, a g-C3N4-Au heterostructure was fabricated through the photo-deposited Au quantum dots (QDs). When subjected to visible light irradiation, this heterostructure exhibited robust nitric oxide (NO) photooxidation activity and stability. With its fluffy, porous structure and large surface area, the nitrogen-defect-enriched g-C3N4 provides more active sites for photooxidation processes. The ability of g-C3N4 to absorb visible light is enhanced by the local surface plasmon resonance (LSPR) effect of Au QDs. Additionally, the lifetime of photogenerated charge carriers is extended by the presence of N defects and Au, which effectively prevent photogenerated electron-hole pairs from recombining during the photooxidation process. Moreover, the oxidation pathway of NO was analyzed through In-situ Fourier transform infrared (FT-IR) spectroscopy and Density Functional Theory (DFT) calculation. Computational findings revealed that the introduction of Au QDs decreases the activation energy of the oxidation reaction, thereby facilitating its occurrence while diminishing the formation of intermediate products. As a result, NO is predominantly converted to nitrate (NO3−). This work unveils a novel approach to constructing semiconductor-cocatalyst heterostructures and elucidates their role in NO photooxidation.

Photogenerated charge carrier processes in carbonate derived nanocrystalline ZnO: photoluminescence, photocurrent response and photocatalytic activity

Photogenerated charge carrier processes in carbonate derived nanocrystalline ZnO: photoluminescence, photocurrent response and photocatalytic activity

Heterostructures based on g-C<sub>3</sub>N<sub>4</sub> for the photocatalytic CO<sub>2</sub> reduction

The interest of the global scientific community in the problems of CO<sub>2</sub> utilization and returning to the carbon cycle has markedly increased in recent years. Among various CO<sub>2</sub> transformation processes, photocatalytic reduction is one of the most promising. Currently, much attention is paid to photocatalysts based on graphitic carbon nitride, since the use of g-C<sub>3</sub>N<sub>4</sub> makes it possible to perform CO<sub>2</sub> reduction under visible or solar light irradiation. To increase the reduction efficiency, g-C<sub>3</sub>N<sub>4</sub> is subjected to various modifications with the most popular and promising approach being the synthesis of composite photocatalysts based on g-C<sub>3</sub>N<sub>4</sub> with other semiconductors to form heterostructures. Depending on the type of semiconductor, transfer of photogenerated charge carriers in these systems can occur by various mechanisms, which largely determine the course of the process and the rates of formation of reaction products. This review addresses studies on the synthesis of composite photocatalysts based on g-C<sub>3</sub>N<sub>4</sub>, with emphasis being placed on the mechanisms of charge carrier transfer and the distribution of products of CO<sub>2</sub> reduction. <br>The bibliography includes 235 references.