Phosphor Layer Research Articles

On the intrusiveness of phosphor thermometry for metal surface temperature measurements in reciprocating engines: an experimental and heat conduction modeling study

Abstract Lifetime-based phosphor thermometry has been applied in a wide variety of surface temperature measurement applications due to its relative ease of implementation and robustness to background interference when compared to other optical temperature measurement methods. It is often assumed that the technique is minimally intrusive if the thickness of the applied phosphor coating is < 20 µm. To evaluate this assumption, high-speed phosphor surface temperature and thermocouple measurements were performed on 4140 steel substrates installed in the cylinder head of an optically-accessible internal-combustion engine for four operating conditions. For phosphor thermometry measurements, four substrates were studied, each coated with a phosphor layer of different thickness ranging between 6 µm and 47 µm. The phosphor thermometry measured temperature swings during combustion were shown to be heavily impacted by the presence of the phosphor coatings, increasing by roughly a factor of 2 - 2.5 when increasing the thickness from 6 µm to 30 µm. A technique was implemented which utilizes the temperature data in combination with a heat conduction model to provide estimates of the temperature swing and heat transfer flux in the absence of the phosphor coating. It was shown that even the 6 µm phosphor coating could lead to an order of magnitude increase in the temperature swing relative to the uncoated 4140 steel substrate. Despite the intrusiveness of phosphor thermometry for the surface temperature measurements, reasonable agreement was demonstrated between heat flux estimates determined with the heat transfer modeling technique and those deduced from temperature-swing measurements using two different high-speed thermocouples. The results indicate that phosphor surface thermometry can be a reliable surface temperature and heat flux diagnostic for transient high heat flux environments, as long as proper care is taken to account for the impact of the phosphor layer on the measurement.

Impacts of Eu2+ -doped K3LuSi2O7 phosphor and a scattering particle on conventional white light emitting diodes

The K<sub>3</sub>LuSi<sub>2</sub>O<sub>7</sub> phosphor doping Eu2+ rare-earth ions (KLS:Eu) was reported to possess broad emission band from near-ultraviolet to nearinfrared. Additionally, this phosphor showed a wide absorption band of 250-600 nm, allowing it to be excited by blue-light chip of 460 nm, making it one of the suitable phosphor materials for a light emitting diode (LED). Besides, the scattering particle material CaCO<sub>3</sub> is incorporated into the yellow phosphor layer to serve the scattering-enhancement purpose. The combination of both materials aims at accomplishing improvements in performance of commercial LED package. The concentration of KLS:Eu is constant while that of CaCO3 is modified. As a result, the scattering factor is regulated and become the key factor influencing the optical outputs of the simulated LED. The increasing CaCO<sub>3</sub> concentration enhances the phosphor scattering efficiency of light, helping to improve the lumen output and color-temperature consistency of the LED. However, the color rendering performance declines as a function of the CaCO3 growing amount, despite the presence of a KLS:Eu phosphor layer. Further works should be done to optimize the application of KLS:Eu in cooperation with scattering particles for a higher-quality LED device.

Eco-friendly synthesis of red-emissive carbon dots for visual alcohol detection and light-emitting diodes

Red-emissive carbon dots (R-CDs) is highly desired in developing full-color solid-state lighting and display applications based on CDs. Developing simple and eco-friendly methods to produce R-CDs is extremely desirable. In this work, two types of R-CDs were obtained via simple and eco-friendly grinding-heating or solvothermal methods using fresh spinach leaves as the carbon source, respectively. The obtained R-CDs naturally possess surface functional groups. These R-CDs were effectively used as sensitive probes for detecting alcohol (including alcohol gas and liquor detection) due to the synergistic effect of the nitrogen-containing surface groups on the R-CDs and the oxhydryl groups in the alcohol solution. Finally, red electroluminescence was achieved by mixing the R-CDs with polyvinyl pyrrolidone as the phosphor layer on a blue light-emitting diode (LED) chip. This work paves the way for the further development of R-CDs in fluorescence probes and full-color LED applications.

Highly luminescent CsPbBr3 perovskite nanocrystal films via the ligand-assisted reaction

Via the ligand-assisted reaction, highly luminescent CsPbBr3 perovskite nanocrystal (PNC) films were synthesized by a simple centrifugal casting process based on the supersaturated recrystallization method. The structure, the optical properties, the morphology, the stability and the potential application of the PNC films were investigated in detail. The results show that under the joint use of OA, DDAB and APTES, the obtained PNC films with 1.5 M DDAB show the strong PL emission with highest quantum yield of 77.5 %, the pure CsPbBr3 structure, the smooth surface and the enhanced stability under UV irradiation. Additionally, the white LED device based on the PNC films obtained here and a commercial red phosphor layer shows excellent optical and color properties and working stability, demonstrating the potential of the PNC films in this study in the field of light-emitting and display.

ZnS:Mn electroluminescent display based on nanostructured indium tin oxide films

Thin-film electroluminescent (TFEL) displays have found applications in various industries and areas due to their unique advantages, where high brightness, a wide temperature range, and reliability are crucial. However, despite their benefits, they also face certain limitations and challenges. TFEL displays typically demand relatively high operating voltages. Total internal reflection in the multilayered structure can significantly impede light extraction from the display. In this study, we propose an optimization of the TFEL display structure to enhance light extraction efficiency and reduce operating voltage. Nanostructured indium tin oxide films, obtained by electron beam evaporation on a heated substrate, were utilized to amplify the electric field in a phosphor layer and to create a non-regular light-scattering relief that effectively breaks internal reflection conditions within the display structure. As a result, the display brightness at operating voltage increased by more than 1.5 times.

Solution-processable organic–inorganic materials with colorful afterglow at room temperature

The development of large-scale manufacture for low-cost afterglow materials is critical for their applications and industrializations. Herein, we presented the organic–inorganic afterglow materials with multiple colors based on boric acid (BA) and aromatic dicarboxylic acids or their diesters. These hybrid materials were facilely prepared by a solution-processable method via evaporating the solvent of the BA and organics solution at room temperature. The crystalized BA provided a rigid surrounding for the organics via hydrogen bonds, which effectively inhibited the non-radiative decay of triplet excitons and gave efficient and persistent room temperature afterglow with the phosphorescent quantum yield up to 57.66%. The phosphorescence properties were almost unchanged when deuterated BA was used instead of BA, indicating the deuteration of the hydrogen bond would not suppress the non-radiative decay from the excited state. Furthermore, a phosphorescence resonance energy transfer process was achieved by introducing 4-[4-(Dimethylamino)styryl]-1-methylpyridinium iodide (DASPI) as the energy acceptor. These BA based system could be used as quick-writable phosphorescent inks for multifunctional applications, such as anti-counterfeiting, information storage, encryption, and even for phosphor layer of light emitting diode. These results not only strengthen the understanding of the luminescence mechanism of BA hybrid materials, but also provide a new access to organic–inorganic afterglow materials.

Effects of Pr3+ -activated BaZrGe3O9@TiO2 phosphor compound on light emitting diodes validated by computer simulation

The Pr<sup>3+</sup> -doped BaZrGe<sub>39</sub> gallogermanate phosphors are reported to have a well-defined successive deep defect structure that effectively mitigates thermal carrier fading. This phosphor also presents a red emission with a peak at 615 nm, originating from the Pr<sup>3+</sup> transtition from <sup>1</sup>D<sub>2</sub> to <sup>3</sup>H<sub>4</sub>. We investigated the impact of Pr<sup>3+</sup> -activated BaZrGe3O9 (referred to as BZG:Pr) on the lighting characteristics of light emitting diodes (LED) packages in this paper. By combining BZG:Pr with TiO<sub>2</sub> particles and silicone, we produced a phosphor layer (designated as BZG:Pr@TiO<sub>2</sub>). The optical performance of the resulting LED was systematically examined by varying the TiO<sub>2</sub> doping percentage. Our findings reveal that the incorporation of the BZG:Pr phosphor enhances the red spectral component, thereby contributing to improved homogeneity in color distribution. However, a progressive increase in TiO<sub>2</sub> content within the phosphor layer corresponds to diminishing luminous output and decreased chromatic rendering efficiency of the LED. Employing a lower concentration of TiO<sub>2</sub> proves advantageous, as it capitalizes on the scattering-enhancing attributes while leveraging the red emission of the BZG:Pr phosphor. This synergistic approach yields a favorable balance between luminosity and color quality, enhancing the LED’s overall performance.

Influence of the Phosphor Layer Composition on Flexible Electroluminescent Device Performance

Electroluminescence (EL) is an innovative technology in the lighting area. EL devices’ main structure consists of a phosphor layer sandwiched between two electrodes. In this work, several alternating-current EL devices were developed by applying a set of sequential layers with combinations of in-house prepared inks and a commercially available ink as the phosphor layer. A flexible polyester textile substrate was functionalized with the inks by spray coating, after knife coating an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely, illuminance intensity and illuminance homogeneity. The developed phosphor layer was composed of zinc sulfide doped with copper (between 30.0 and 38.1 wt%) and diluted by using a diluent at different concentrations (from 28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented a 35.4% ZnS:Cu ratio and was diluted with 33.0% diluent. This study aimed to determine the best formulation of the phosphor layer, which can be highly useful for further developments of EL devices, taking into account different applications in the market.

Bimetal Thin Film, Semiconductors, and 2D Nanomaterials in SPR Biosensors: An Approach to Enhanced Urine Glucose Sensing.

This work introduces a systematic approach for the development of Kretschmann configuration-based biosensors designed for non-invasive urine glucose detection. The methodology encompasses the utilization of various semiconductors, including Silicon (Si), Germanium (Ge), Gallium Nitride (GaN), Aluminum Nitride (AlN), and Indium Nitride (InN), in combination with a bimetallic layer (comprising Au and Ag films of equal thickness) to enhance the biosensor sensitivity. Additionally, 2D nanomaterials, such as Black Phosphorus and Graphene, are integrated into the semiconductor layers to enhance performance further. These configurations are meticulously optimized through the application of the transfer matrix method (TMM), and the sensing parameters are assessed using the angular modulation method. Among the semiconductors, AlN and GaN exhibit superior results. On these substrates, Graphene and Black phosphorous (BP) layers are applied, resulting in four final structures (thicknesses in nm): BK7/Au(26)/Ag(26)/Si(6)/BP(0.53)/Biosample, BK7/Au(26)/Ag(26)/AlN(14)/BP(0.53)/Biosample, BK7/Au(26)/Ag(26)/GaN(12)/BP(0.53)/Biosample, and BK7/Au(26)/Ag(26)/GaN(12)/Graphene(0.34)/Biosample. These biosensors achieve Sensitivity(° /RIU) and Figure of Merit (FoM) (1/RIU) of 380, 360, 440, 400, and 58.5, 90, 90.65, and 82.4, respectively. Subsequently, these high-performing sensors undergo testing with actual urine glucose samples. Among them, two biosensors, BK7/Au(26)/Ag(26)/AlN(14)/BP (0.53)/Biosample and BK7/Au(26)/Ag(26)/GaN(14)/Graphene(0.34)/Biosample, exhibit outstanding performance, with sensitivities (° /RIU) and FoM (1/RIU) of 394.44 & 294.44, and 112.6 & 92.01 respectively. A comparison is also made with relevant previously published work, revealing improved performance in glucose detection.

STUDY OF K2SiF6:Mn4+@SiO2 PHOSPHOR FOR WHITE LEDS WITH HIGH ANGULAR COLOR UNIFORMITY

The distinctive wide-band blue illumination absorption and red strait-line discharge of the phosphor K2SiF6:Mn4+ (KMnSF) make it an attractive material for manufacturing warm white light-emitting diodes (WLED). Nevertheless, using the highly corrosive raw ingredient HF to produce commercial KMnSF red phosphor has negative effects on the environment and people. In this study, microfluidic technology was used to successfully manufacture the KMnSF without the need for HF compound while resulting in a phosphor product with homogenous granule shape and size. The luminescence capabilities of the KMnSF samples were then thoroughly examined and characterized. Eventually, we made WLED packages comprising of blue LED chips, yellow phosphor Y3Al5O12:Ce3+ (YGA:Ce), red phosphor KMnSF, and SiO2 scattering particle. Via varying the SiO2 concentration during the simulation process, the prepared WLED’s optical performances are obtained. The scattering properties of the phosphor layer as well as the lighting transmission and distribution were simulated with the utilization of both LightTools software and Monte Carlo theory. According to the outcomes, the microfluidic-synthesized K2SiF6:Mn4+ proves to be appropriate for WLED apparatuses. Besides, the proposed phosphor compound with SiO2 scattering particles showed the improvement in luminous flux and angular uniformity of the WLED.

Design and development of speckle-free high-power laser-driven phosphor converted compact automotive headlamp module

The applicability of diode-lasers in automobile headlights is an advanced innovation for the automobile illumination industry due to the extraordinary properties of laser light over conventional light sources, such as high brightness, wide colour gamut, high directionality, low energy consumptions and long lifetime. Lasers are highly coherent in nature, so they encounter the problem of unwanted speckles and spurious fringes and always require a high level of opto-thermal engineering along with speckle reduction mechanisms for high lumen laser applications. Targeting such challenges, in this paper, we report an innovative design and development scheme for a high lumen laser-based automotive headlamp module. The headlamp prototype comprises a set of four cylindrical diffusers which distribute the high energy laser radiation via scattering along the length of the diffusers within a metallic mirro-based pyramidal cavity reflector. The scattered laser light from cylindrical diffusers interacts with a remote phosphor layer that prevents phosphor–resin burning. The pyramidal cavity reflector plays an important role in making the laser light uniform and speckle-free, via spatial and angular diversity, as light exits from the cavity after multiple internal reflections. This reflector redirects the highly concentrated white light over a long range without using any projection lens. The design and performance of the headlight system was studied using TracePro simulation software and tested experimentally in a photometric laboratory. The International Commission on Illumination (CIE) coordinates of the light generated by the headlamp was (0.3947, 0.4908) and the correlated colour temperature was 4240 K, which represents warm white light illumination.

The Development of a Remote Edge-Lit Backlight Structure with Blue Laser Diodes

In this study, we introduce a novel design of a remote edge-lit backlight structure featuring blue laser diodes (LDs). These LDs were integrated into a remote yellow phosphor layer on a light guide plate (LGP). Blue light emitted by the LDs passes through the LGP and spreads to the remote phosphor layer, generating white light output. Owing to the incorporation of a scattering layer between sequential LGPs, the remote edge-lit backlight structure facilitates the expansion of the output surface of the LGP by combining multiple individual LGPs. Two- and three-LGP remote edge-lit backlight structures demonstrated acceptable white illuminance uniformity. The proposed architecture serves as a viable solution for achieving uniform illumination in planar lighting systems using blue LDs; thus, this structure is particularly suitable for linear lighting or slender backlighting instead of display stand applications.

Film characteristics of ZnS:Mn phosphor prepared by metal precursor sulfurization and its application to inorganic electroluminescent devices

A ZnS:Mn phosphor film for an inorganic electroluminescent (EL) device fabricated by metal precursor sulfurization was evaluated. Metallic ZnMn was thermally evaporated at room temperature and then sulfurized by sulfur gas flowing in a tube furnace at various temperatures from 400 to 800 °C. X-ray diffraction, energy dispersive x-ray spectroscopy, and photoluminescence observations indicated that a ZnS:Mn phosphor layer was formed after sulfurization. A thick-dielectric EL device was manufactured using the obtained ZnS:Mn phosphor. The EL luminance of 216 cd/m2 at 1.0 kHz was measured when the phosphor layer was sulfurized at 500 °C. A charge density versus voltage (Q-V) curve was also analyzed to evaluate the EL phosphor characteristics.

UVC Emission Devices Based on Alternating Current Inorganic Electroluminescence Using Y2SiO5:Pr3+ Phosphors

Ultraviolet C (UVC: 200-280 nm) lighting is urgently required for a number of sterilization applications such as water and air disinfection, food processing, and medical sterilization. Compared to other UVC emission sources, AC-driven inorganic phosphor electroluminescent (EL) devices are appealing due to their wide viewing angle, fast response time, low power consumption, high contrast, simple manufacture, and cost effectiveness. Although the luminance of inorganic phosphor EL devices is typically low, it is sufficient for most low-cost lighting and large-area display applications. In addition, inorganic phosphor EL devices have the advantage of emitting light without generating much heat. In this study, UVC emission was demonstrated through EL devices using a UVC phosphor. Pr3+-doped Y2SiO5 (Y2SiO5:Pr3+) is used for UVC light, Y2SiO5:Pr3+ phosphor shows a broad UVC emission at 280 nm from the f-d transition of Pr3+ ions as well as a sharp red emission at 610 nm from the f-f transition of Pr3+ ions. The phosphors were synthesized in three types to fabricate EL devices. The Y2SiO5:Pr3+ powder, film, and nano-powder formed the phosphor layers of EL devices by screen printing, spin coating, and electrophoretic deposition, respectively. In order to emit UVC light, patterned gold was used for transparent electrodes of the devices instead of conventional indium tin oxide (ITO), which absorbs the UV region. The EL devices were demonstrated in two types: powder EL and electrolyte EL. The fabricated EL devices showed a wide range of UVC emission from 260 nm to 330 nm. Finally, luminescent and electrical analysis of each device was performed to analyze the characteristics.

The use of CaO:Eu<sup>3+</sup> and Zn<sub>2</sub>SiO<sub>4</sub>:Mn<sup>2+</sup> phosphors to increase the color quality and illumination intensity of WLEDs

The lumen efficacy in remote phosphor structure displayed remarkable enhancements, which is notable for the development of white light-emitting diodes (WLEDs). Nevertheless, its quality of colour is deemed not as good as that of the conformal or in-cup phosphor structure. Therefore, the goal of this research is to achieve a better quality of colour and significant luminous flux value for remote phosphor configuration by using extra phosphor layers. In particular, the two-layer and three-layer structures with the implementation of green and red phosphors are proposed. Comparing these two structures can help pinpoint the best suited for the WLED production. The assessment of each structure’s effect on the WLEDs’ optical parameters was determined under various correlated temperatures of colour (5,600-8,500 K). The outcomes indicated that the three-layer structure enhanced the quality of colour with greater efficiency compared to the two-layer structure due to the increased color rendering index (CRI), color quality scale (CQS), and photoluminescence (PL), and reduced colour deviation. The scattering improvement of the three-layer structure is a key factor of these accomplishments, proven by the scattering theory of Mie. Therefore, the three-layer structure is potential for developing WLED production.

The concentration factor on the mixture of Ag paste and H3PO4 solution as a dopant paste for contact formation in silicon solar cells

Screen printing dopant is a new technique to create emitter regions on solar cells. On top of the emitter region, there will be screen-printed metallic contacts that are commonly used silver as front contact. Both processes are performed in separate procedure which requires two different diffusion process involving a high-temperature process. Silver makes good ohmic contact on both light and heavily doped. A solution is proposed by applying a single step of screen printing and annealing process of Ag and phosphorus acid. Simultaneous annealing of Al, Ag, Ag/P screen-printed pastes form diodes with and without heavily doped phosphorous layers under Ag contacts on n-type and p-type silicon wafers by annealing at a constant temperature of 900℃ while varying annealing time from 10-40 seconds at a 10-second interval. The cross-section image of 5% and 10% of Ag/P was measured by using FESEM with EDX report has identified the presence of phosphorus in the Ag/P paste. Dark IV shows an ohmic contact for both p- and n-type. The ability to form the Ag/P paste in the screen-printing process makes it amenable to use as a self-dopant paste process in solar cells.

Fabrication and characterization of green ZnS:Tb AC- electroluminescent devices by ultrasonic spray pyrolysis

MISIM (metal-insulator-semiconductor-insulator-metal) structures of alternating current thin film electroluminescent (ACTFEL) devices were deposited on ATO/glass substrates by the ultrasonic spray pyrolysis technique. Zirconium oxide and terbium doped zinc sulfide were used as dielectric and semiconductor phosphor layers, respectively. A focused ion beam equipment was used to prepare a lamella of the MISIM structure, for cross-sectional scanning electron microscopy analysis in the STEM mode. Chemical analysis by energy-dispersive X-ray spectroscopy (EDS) elemental maps was also made for the identification of the distribution of the elements through the layers composing the MISIM structure. Characteristic Tb3+ emission bands due the 5D4 ->7FJ transitions were obtained by AC voltage application at 10 kHz with the main peak centered at 542 nm. An increase in the electroluminescent intensity and a shift of the CIE coordinates toward a purer green color with increasing the applied voltage was observed. The threshold voltage of these green electroluminescent devices was 46 Vrms, and a luminance up to 41 cd/m2 was obtained for the maximum applied voltage of 76.9 Vrms.

Imaging low-energy positron beams in real-time with unprecedented resolution

Particle beams focused to micrometer-sized spots play a crucial role in forefront research using low-energy positrons. Their expedient and wide application, however, requires highly-resolved, fast beam diagnostics. We have developed two different methods to modify a commercial imaging sensor to make it sensitive to low-energy positrons. The first method consists in removing the micro-lens array and Bayer filter from the sensor surface and depositing a phosphor layer in their place. This procedure results in a detector capable of imaging positron beams with energies down to a few tens of eV, or an intensity as low as 35e+/s/mm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${35}\\,{\\hbox {e}^+/\\hbox {s/mm}^{2}}$$\\end{document} when the beam energy exceeds 10 keV\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\\hbox {keV}}$$\\end{document}. The second approach omits the phosphor deposition; with the resulting device we succeeded in detecting single positrons with energies upwards of 6keV\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${6}\\,{\\hbox {keV}}$$\\end{document} and efficiency up to 93%. The achieved spatial resolution of 0.97 μm\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\upmu \\hbox {m}$$\\end{document} is unprecedented for real-time positron detectors.

Low voltage thick-film electroluminescent device with evaporated ZnS:Mn and spin coated BaTiO3 dielectric layer

In a thick-dielectric electroluminescent (TDEL) device, which is a variation of thin-film electroluminescent devices, one of the insulation layers is replaced by a thick-film dielectric layer. High brightness and reliability are the features of TDEL owing to a higher withstanding voltage of the thick-film dielectric layer. This paper presents a new type of TDEL with a bottom emission structure. The thick-film dielectric layer was manufactured by spin coating using an ink material, which is a mixture of BaTiO3 powder and a binder resin. The thicknesses of the phosphor and dielectric layers were minimized to reduce the operating voltage. A threshold voltage as low as 50 V and a maximum luminance of 1000 cd/m2 were obtained at 60 V.

Sensitive MIM plasmonic biosensors for detection of hemoglobin, creatinine and cholesterol concentrations

In this paper, a nano structure based on graphene-plasmonic/black phosphorous combination is proposed and investigated. The main goal of the presented work is detection of different biological elements in blood samples. The structure is consisted of different layers of Ag (silver), air, graphene and black phosphorous. Various layers are considered in the T-shaped, U-shaped and split ring-shaped waveguides. The incident field would be applied to the T-shaped waveguide and output signals would be transmitted to the three output ports (output1, output2 and output3). The structure is supposed to function as sensitive bio-sensors. Therefore, effects of different structural parameters (r2, t2, r3, t3, r4, t4), chemical potentials (μc2, μc3, μc4) and black phosphorous layers on the transmission spectrum of output ports are considered. These processes lead to improved transmission's peak value and wavelength (enhancing sensor's functionalities). Finally, the improved structure would be considered as refractive index sensors. Cholesterol, Creatinine and Hemoglobin concentrations in blood samples would be diagnosed at ouput1, output2 and output3 ports, respectively. Considerable sensitivity factors of 5333.3[nm/RIU], 1562.5[nm/RIU] and 800[nm/RIU] are obtained for Cholesterol, Creatinine and Hemoglobin concentrations, respectively. Other important parameters (figure of merit, quality factor and limit of detection) are also calculated for each biomolecule sensor. Considering these sensitivity factors, the structure can be utilized as accurate bio-sensors in optical integrated circuits.