Formation Of Phase Research Articles

Crystallization and Optical Behaviour of Nanocomposite Sol-Gel TiO2:Ag Films.

Sol-gel spin coating method was employed for depositing TiO2 and Ag-doped TiO2 films. The effects of Ag doping and the annealing temperatures (300-600 °C) were studied with respect to their structural, morphological, vibrational, and optical properties. Field Emission Scanning Electron microscopy (FESEM) investigation exhibited the grained, compact structures of TiO2-based films. Ag incorporation resulted in a rougher film surface. X-ray diffraction (XRD) results confirmed the formation of Ag nanoparticles and AgO phase, along with anatase and rutile TiO2, strongly depending on Ag concentration and technological conditions. AgO fraction diminished after high temperature annealing above 500 °C. The vibrational properties were characterized by Fourier Transform Infrared (FTIR) spectroscopy. It was found that silver presence induced changes in IR bands of TiO2 films. UV-VIS spectroscopy revealed that the embedment of Ag NPs in titania matrix resulted in higher absorbance across the visible spectral range due to local surface plasmon resonance (LSPR). Ag doping reduced the optical band gap of sol-gel TiO2 films. The optical and plasmonic modifications of TiO2:Ag thin films by the number of layers and different technological conditions (thermal and UV treatment) are discussed.

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites.

A dense monolithic SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C high-entropy ceramic nanocomposite was prepared using a polymer-derived ceramic (PDC) method combined with spark plasma sintering (SPS). The microstructural evolution and mechanical properties of the obtained nanocomposites were characterized by X-ray diffractometer (XRD), transmission electron microscope (TEM), scanning-electron microscope (SEM), and nanoindentation. The results indicate that the phase composition of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C can be adjusted by modifying the metal content of the single-source precursor (SSP) through molecular design. The resulting precursor exhibits an exceptionally high ceramic yield, with mass retention of over 90% at 1100 °C, which guarantees the densification of the final SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C composites. The PDC route facilitates the in situ formation of a high-entropy phase within the ceramic matrix under low temperature pyrolysis conditions. Combined with SPS, a dense monolithic SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C nanocomposite was obtained, exhibiting an open porosity of 0.41 vol%, nano-hardness of 27.47 ± 0.46 GPa, elastic modulus of 324.00 ± 13.60 GPa, and fracture toughness of 3.59 ± 0.24 MPa·m0.5, demonstrating excellent mechanical properties.

Effect of Rotational Speed on Microstructure and Properties of Al‐Based Composite Reinforced with High‐Entropy‐Alloy Particles Fabricated by Friction Stir Processing

In the present investigation, the production of composites based on 7075Al is involved, reinforced with particles of high‐entropy alloy (AlCoCrFeNi), using the friction stir processing (FSP) technique. The primary objective is to examine how varying the rotational speed during processing affects the uniformity of the composite microstructure, the strength of the bonding between different materials, and the mechanical properties of the composite. In these findings, it is indicated that higher processing rotational speeds lead to enhanced homogeneity of the composite material and promote strong bonding with the matrix. The Al13Co4 phase is generated at the interface before the formation of the Al5Co2 phase. The microhardness of the composites exhibits an increase in hardness of 78%, 84%, 86%, and 83% compared to the hardness of the 7075Al. Similarly, the tensile strength is enhanced by 26%, 36.7%, 49%, and 40%, respectively. The broken surface shows an even spread of particles with many small depressions, which is a clear sign of a common type of fracture that can stretch without breaking. The primary processes that enhance the strength of the FeCoNiCrAl/7075Al composite manufactured by FSP include the load‐transfer effect, dispersion strengthening, grain refinement strengthening, and thermal mismatch strengthening.

Empirical Analysis of Stability of An+1BnO3n+1 Ruddlesden–Popper Phases Using Reciprocal n-Values

Layered An+1BnO3n+1 (n = 1…∞) Ruddlesden–Popper (RP) phases are a promising system for a variety of applications. Within the RP family, the thermodynamic properties of the phases are essentially additive with variation in the n value, but at present, there are no general approaches that would allow one to evaluate the individual stability of the RP phases and the possibility of their interconversion. The aim of this paper is to present a novel concept for performing a thermodynamic analysis of RP phases using the reciprocal values of the index n. We present an empirical equation ΔG1/n = ΔGP + B1/n + B2/n2, where ΔG1/n and ΔGP are the molar Gibbs energies of formation of the Ruddlesden–Popper (RP) phase (AO)1/nABO3 and the parent ABO3 perovskite, respectively, and n is a stoichiometry index of An+1BnO3n+1 RP phase. The correlation was validated using available thermodynamic data for the systems Sr-Ti-O, Ca-Ti-O, Sr-Zr-O, La-Ni-O, and La-Co-O. For all A-B combinations, the equation quantitatively describes the Gibbs energy of RP phase formation. Predicted values for the non-linear approximation lie within the experimental uncertainty in determining ΔG1/n. The proposed correlation was used to analyze the relative stability of the RP phases and to determine the feasibility of synthesizing new compounds.

Crystallization-Controlled Structure and Thermal Properties of Biobased Poly(Ethylene2,5-Furandicarboxylate).

Crystallization-controlled structure and thermal properties of biobased poly(ethylene 2,5-furandicarboxylate) (PEF) were studied. The cold-crystallization temperature controlled the structure and thermal properties of the biobased PEF. The melting was complex and evidenced the presence of a significant fraction of less-stable crystals with a low melting temperature that linearly increased with Tc, which formed already during the early stages of crystallization, together with those melting at a higher temperature. Low Tc resulted in the α'-phase formation, less crystallinity, and greater content of the rigid amorphous phase. At high Tc, the α-phase formed, higher crystallinity developed, the rigid amorphous phase content was lower, and the melting temperature of the less-stable crystals was higher; however, slight polymer degradation could have occurred. The applied thermal treatment altered the thermal behavior of PEF by shifting the melting of the less stable crystals to a significantly higher temperature. SEM examination revealed a spherulitic morphology. A lamellar order was evidenced with an average long period and small average lamella thickness, the latter about 3-3.5 nm, only slightly increasing with Tc.

Enhanced Propylene/Propane Separation via Aniline-Decorated ZIF-8 Membrane: Lattice Rigidity Adjustment and Adsorption Site Introduction.

Metal-organic framework (MOF)-based membranes excel in molecular separation, attracting significant research interest. The crystallographic microstructure and selective adsorption capacity of MOFs closely correlate with their gas separation performance. Here, aniline was added to the ZIF-8 synthesis in varying concentrations. Aniline, encapsulated within ZIF-8 cavities, interacts strongly with the 2-methylimidazole linker, resulting in both a shift in crystallographic phase from I_43 m to Cm in Rietveld refinement of X-ray diffraction (XRD) patterns and the selective adsorption behavior between propylene and propane. Consequently, an aniline decorative ZIF-8 (Anix-ZIF-8) membrane was prepared using a fast current-driven synthesis method, which exhibits good propylene/propane separation selectivity of up to 85. Calculation of the interaction energy between aniline and the various crystallographic phases of ZIF-8 using density functional theory (DFT) further verifies that aniline not only promotes the formation of crystallographic Cm phase, but also enhances the adsorption selectivity of propylene over propane. Aniline modification effectively tunes the crystallographic microstructure of ZIF-8, thereby, improving molecular sieving capabilities.

IMPROVEMENT OF THE ALLOY STRUCTURE OF THE Ni-Cr-Со-W-Mo-Al-Ti-C SYSTEM

Purpose. Establishing the specifics of the influence of alloying elements on the formation of carbides in the structure, their shape and the possibility of separating TLC phases for the system of the Ni-Cr-Co-W-Mo-Al-Ti-C type using the CALPHAD calculation method of prediction in comparison with data obtained by the method of raster electron microscopy. Research methods. The results of experimental and calculated data, formed on the basis of experimental and results taken from open sources, are presented. The chemical composition was determined on a REM-106I scanning electron microscope equipped with an energy dispersive analysis. Experimental values were processed by the method of least squares with obtaining correlation dependencies of the “parameter-property” type and establishing mathematical equations of regression models that optimally describe these dependencies. Results. It was established that when the concentration of titanium is more than 4 % and molybdenum is more than 6 % and 15 % chromium, the formation of TSC phases (Р, s and m- phases) is possible, which reduce the operational properties of the alloy. It was found that when the alloy contains more than 25 % chromium, a solid chromium-based solution is formed, which reduces the properties of the alloy (mechanical and corrosion). It is shown that the obtained dependences correspond to reality and coincide with experimental data at the level of 10 %. Scientific novelty. Obtained dependences of the influence of alloying elements on the chemical composition of carbides will allow predicting properties without conducting experiments. It was established that changes in the course of dependencies are closely correlated with the processes occurring in the structure of alloys. Practical value. The obtained dependencies can be used both for the development of new heat-resistant alloys and for the improvement of the compositions of industrial alloys.

Developing alkali-activated controlled low-strength material (CLSM) using urban waste glass and red mud for sustainable construction

Using industrial waste in controlled low-strength material (CLSM) offers many benefits and addresses waste management issues. However, identifying optimal CLSM design while balancing environmental impacts and engineering properties poses a notable challenge. Herein, new alkali-activated CLSM formulations based on urban waste glass and red mud (RM) are proposed for the first time with systematic investigations into the material properties and sustainability. The formulations involve the ternary blends of slag, glass powder (GP) and RM as the binders and crushed glass as aggregate. Our observations show RM has a clay-like texture with complex crystalline phases rich in Al and Fe. Increasing the proportion of RM to GP notably decreases the flowability, extends the setting time and impairs the mechanical properties. Nevertheless, red mud demonstrates a crucial role of reducing bleeding level especially for the mixtures with high proportions of glass aggregate. The standard leachate tests as per toxicity characteristic leaching procedure (TCLP) show the heavy metals leached from the CLSM are below the concentration limits and exhibit low mobility. The microstructural and thermodynamic analyses reveal the precipitation of calcium-(sodium-)aluminosilicate hydrate (C-(N-)A-S-H) as the major binding material. The reactive Fe and Al in red mud most probably contribute to the formation of hydrogarnet phases. Moreover, the suggested CLSM formations typically exhibit reduced carbon emissions and lower costs compared to the traditional CLSM produced with cement and fly ash, underlining their environmental sustainability and cost-effectiveness. This study provides a potential guideline for the flowable fill construction in the regions with bauxite producers.

Unveiling the influence of dopants on structural, defect chemistry, morphological and optical characteristics of NiO nanostructures

Abstract In this paper, undoped and doped (Fe, Co and Fe-Co) nickel oxide (NiO) nanostructures have been synthesized using co-precipitation method. Prepared samples were characterized for the structural, compositional, morphological and optical properties using x-ray diffraction, scanning electron microscopy (SEM), Energy dispersive spectrocopy (EDS), UV-visible spectroscopy and photoluminescence spectroscopy. Structural analysis confirmed the single cubic phase formation of undoped and doped samples. Defect chemistry showed that Fe-Co co-doped NiO possesses a lower density of defects than other samples. SEM results revealed the agglomeration of particles. EDS results confirmed the presence of Ni, O, Fe and Co in the respective undoped and doped samples. Optical analysis revealed the band edge shifts with the incorporation of dopants in the NiO crystal lattice confirmed the variation of band gap energy. Emission peaks were observed in the UV and visible regions. The Incorporation of dopants in the crystal lattice causes variation of emission centers. Surface oxygen vacancies and imperfections significantly impact the emission characteristics of NiO. Variable spectral response of NiO with dopant incorporation has potential for optoelectronic applications.

Production of Autoclaved Cementitious Composites Using Recycled Waste Glass

ABSTRACTOne of the major negative environmental implications of economic growth and the advancement of information technology is the large quantity of electronic waste dumped in landfills. Cathode ray tubes (CRTs) from outdated televisions and computer monitors are a significant source of electrical waste. The CRT funnel primarily consists of silica, significant alkalis (Na2O‐K2O), and heavy metals like barium‐strontium, along with a substantial lead (Pb) content that may contaminate the soil. Owing to its heavy metal content, CRT is considered hazardous waste, and regulations require its glass to be recycled or repurposed instead of landfill disposal. The low pozzolanic activity of CRT silica suggests that its high content, when paired with an optimized particle size and specific curing conditions, can enhance the mechanical properties of cement‐based products. Hydrothermal treatment has been found to speed up both the hydration of ordinary Portland cement (OPC) and the pozzolanic reactions. Since the main objective was to safely recycle large amounts of CRT, three mixes were proposed with 10%, 20%, and 30% OPC + 90%, 80%, and 70% CRT, respectively, and the effect of hydrothermal curing conditions on mechanical properties and durability of these blends was investigated. CRT‐70, a blend containing 70% CRT glass waste, showed enhanced strength due to the formation of zeolitic phases and calcium silicate hydrate (CSH). These phases also provided CRT‐70 with notable fire resistance, ensuring its structural stability under elevated temperatures. These results demonstrate the possibility of production of precast building products via high‐volume recycling of hazardous CRT waste.

Aluminum-Modified Plasma Nitriding with High Efficiency and Enhanced Performance

Aluminum-modified plasma nitriding was developed in this research by the addition of a few FeAl particles around samples of 42CrMo middle carbon alloy steel during plasma nitriding. The goal of this study was to enhance nitriding efficiency and the combined performance of the steel. The research results show that nitriding efficiency was greatly enhanced, by about 6 times, with the effective hardening layer rising from 224 μm to 1246 μm compared with traditional plasma nitriding at 520 °C/4 h. More importantly, the compound layer increased just a little bit, from 11.64 μm to 14.32 μm, which remarkably reduced the ratio of the compound layer’s thickness to the effective hardening layer’s thickness, thus being quite beneficial to decreasing the brittleness level, making the brittleness level decrease from Level 4 to Level 1. Also, extremely high surface hardness and excellent wear resistance were obtained by aluminum-modified plasma nitriding due to the formation of hard phases of AlN and FeAl in the nitrided layer, with the surface hardness rising from 755 HV0.025 to 1251 HV0.025 and the wear rate reducing from 8.15 × 10−5 g·N−1·m−1 to 4.07 × 10−5 g·N−1·m−1. In other words, compared with traditional plasma nitriding, wear resistance was enhanced by two times after aluminum-modified plasma nitriding. Therefore, this study can provide comprehensive insights into the surface characteristics and combined performance of aluminum-modified plasma nitriding layers.

Exploration of High‐Pressure Annealing and Microwave Annealing in Palladium Germano‐Silicide Formation for Si0.8Ge0.2‐Based Complementary Metal‐Oxide–Semiconductor Transistors

In this study, forming palladium germano‐silicide on Si0.8Ge0.2‐based complementary metal‐oxide semiconductor (CMOS) transistors by high‐pressure annealing compared to microwave annealing is investigated. Boron‐doped Si0.8Ge0.2 layers are epitaxially grown on n‐type Si wafers, achieving an initial boron concentration of 5 × 1015 cm−3, which increase to ≈6 × 1020 cm−3 after microwave annealing, reducing sheet resistance. Palladium is deposited using electron beam evaporation to form a 15 nm layer on Si0.8Ge0.2 (200 nm)/Si (100) substrates. High‐pressure annealing is conducted from 300 to 500 °C in N2 ambiance at 5 kg cm−3, while microwave annealing is performed at 5.8 GHz and 1800–3000 W for 100 s. X‐ray diffractometer confirms high‐intensity Pd2Si phase formation, but scanning electron microscope and atomic force microscope reveal increased surface roughness and clustering after annealing. Sheet resistance increases from 10.35 Ω sq−1 (unannealed) to 131.8 Ω sq−1 (high‐pressure annealing at 300 °C) and 85.8 Ω sq−1 (microwave annealing at 1800 W). In these results, the trade‐offs between annealing methods and metal choices for achieving low contact resistance and Schottky barrier heights in p‐type Si0.8Ge0.2 CMOS circuits are highlighted.

The Gypsum Influence on the Formation of Secondary Phases During Autoclave Leaching of Gold-Bearing Concentrates and the Silver Recovery Using Cyanidation.

Autoclave leaching of sulfide concentrates may produce various ferric secondary phases, depending on the arsenic content and temperature. Silver is converted to argentojarosite, from which it is not recoverable by standard cyanidation methods. To increase silver recovery, it is necessary to reduce the argentojarosite formation during autoclave leaching. This study was devoted to the influence of gypsum on the formation of secondary phases of ferric arsenate and the subsequent recovery of gold and silver by cyanidation. The addition of gypsum at a consumption of 0.1 g/g(concentrate) helped to increase silver extraction from 13.4 to 98% at cyanidation. Gold recovery was 99%. An increase in gypsum consumption contributed to the ferric arsenate sulfate formation with an increased sulfate sulfur content, and a decrease in the As/S(sulfate) molar ratio in the cake from 3.7 to 0.88 contributed to an increase in silver extraction at cyanidation of up to 98%. Basic ferric sulfate is not formed in this case, since according to EDS mapping, the distribution of arsenic and sulfur over ferric-containing particles is uniform. According to TCLP, stable, sparingly soluble ferric arsenate phases are formed and the cake obtained after cyanidation is stable and suitable for disposal, since the final arsenic concentration in the solution was 0.45 mg/dm3.

Phase Formation, Polymorphism, Optical Properties, and Conductivity of Nd2WO6-Based Compounds and Solid Solutions

Phase Formation, Polymorphism, Optical Properties, and Conductivity of Nd2WO6-Based Compounds and Solid Solutions

Unleashing the elastocaloric cooling potential of 3D-printed NiTi alloy with heterogeneous microstructures and Ni4Ti3 nanoparticles

Toward the development of elastocaloric (eC) refrigeration applications, this study examines how Ni4Ti3 nanoparticles improve the eC properties of laser powder bed-fused (LPBF) NiTi alloys, with a focus on the formation of a NiTi/Ni4Ti3 nanocomposite. The LPBF-produced microstructure offers significant advantages: i) a heterogeneous grain structure that provides complementary benefits—fine grains offer higher deformation resistance while coarse grains initiate phase transformation (PT) earlier, releasing more latent heat; ii) a strong <001>//building direction texture that enhances recoverability. However, these benefits are partially limited by grain boundary slip during PT, leading to lower cooling efficiency and increased energy dissipation in as-built NiTi alloys. To address these issues, Ni4Ti3 nanoparticles are introduced through aging treatment, forming a composite structure that strengthens grain boundaries. Given the challenges of applying severe plastic deformation to 3D-printed components, this approach may offer a more practical solution. The study also reveals that Ni4Ti3 nanoparticles contribute to: 1) reducing Ni content in the matrix, increasing lattice size and enthalpy, which enhances the temperature drop (ΔTad); and 2) promoting R phase formation, which hinders the B2↔B19’ PT, reducing energy dissipation and improving the coefficient of performance (COPmat). The balance of these effects depends on nanoparticle size, with smaller particles (∼5–12 nm) amplifying the second effect, while larger particles (∼130 nm) increase the first effect. At 350 °C aging, the optimized nanocomposite exhibits a maximum COPmat of 15 and ΔTad of 14K, representing a 163 % improvement over the as-built alloy. This work highlights the potential of NiTi composites in 3D-printed eC components.

Effect of pulse current on the creep ageing behavior of pre-strained 2195 Al-Li alloy

Pre-strained aluminum lithium (Al-Li) alloy plates have ultra-high strength and comprehensive performance after aging treatments, and are widely used in the aerospace industry. The initial increase in dislocation density caused by these pre-strains will significantly affect the evolution of deformation, microstructure, and mechanical properties during the pulse current assisted creep ageing forming process. Therefore, the effect of pulse current on the creep ageing behavior of 2195 Al-Li alloy with different pre-strains (0 %, 4 %, and 8 %) was investigated. As the pulse current increases within the first 1h creep aging process of the various pre-strain samples, the 1h creep strain significantly increases and the subsequent steady-state creep rate slightly reduce. Moreover, the larger the pre-strain, the higher the total creep strain. Pulse current promotes the movement and recovery of initial dislocations, and promotes the fine formation of T1 phase and suppresses the nucleation of θ′ and δ′ phase, thereby improving mechanical properties. Compared with the conventional creep ageing process, the pulse current acting on pre-strained 2195 Al-Li alloy significantly increased the peak aged strengthen and shorten the peak aging time. Meanwhile, the peak time platform period has also been significantly extended. It is evident that the application of pulse current assisted creep ageing forming process to pre-strained 2195 Al-Li alloy plates can significantly improve formability and mechanical properties, enlarges the forming process window and realize collaborative manufacturing of Al-Li alloy component shape and performance.

High temperature environmental scanning electron microscopy characterization of transient phase formation during conversion of simulated nuclear waste feed to glass

In-situ High-Temperature Environmental Scanning Electron Microscopy (HT-ESEM) is used to characterize the transient phases formed during the melting of complex glass batch mixtures representing simulated nuclear waste feeds. The first phenomenon that occurs is the formation of oxyanionic salt melt, followed by the reaction of oxyanionic salts with refractory grains containing Si, Al, or Mg through surface reactions to form a molten alkali-alumino-boro-silicate phase. The onset temperatures of gas bubble formation and primary foaming are directly determined from the HT-ESEM measurements. The formation of sulfate lakes as well as the formation of high-temperature transient phases floating at the sample surface are also directly observed and identified. Convection currents are observed and their consequences on glass homogenization are discussed.

Wire-based friction stir additive manufacturing towards isotropic high-strength-ductility Al-Mg alloys

ABSTRACT The formation of eutectic Al-Mg2Al3 phases along the grain boundaries makes it difficult to improve the mechanical properties of high-magnesium-content aluminum alloys. Here, wire-based friction stir additive manufacturing(W-FSAM) was proposed as a novel solid-state additive manufacturing technology. The shearing, transport, and thermo-plasticisation processes of the deposited materials were achieved by a rotational tool and a stationary barrel. The original Mg2Al3 phases were refined and dissolved into the matrix and formed supersaturated solid solution structures. The refined grains with a diameter of 1.27 ± 0.64 μm were achieved through the dynamic recrystallization process. The components achieved isotropic mechanical properties due to the homogeneous equiaxed fine-grain structure. The ultimate tensile strength reached 415 ± 11 MPa with an elongation of 31.0 ± 2.0%, superior to the commercial 5xxx products. The enhanced strain hardening capacity was achieved by the suppressed emission of dislocations from grain boundaries and the interaction between the supersaturated solid solute atoms and mobile dislocation.

A Comparative Study of Hydrothermally Leached Al3TM and Al3TM-Rh (TM=Zr, V, Ce) Intermetallic Compounds for Catalytic Oxidation of Carbon Monoxide.

Rise of the mute assassin "carbon monoxide (CO)" levels impact all aerobic life. The elevated rates of CO concentration endure climatic and geographical characteristics that exacerbate air pollution. Herein, a simple approach for hydrothermal leaching (HyTL) of Al3TM-Rh0.5 (Target material (TM)=Zr, V, Ce) and Al3TM (TM=Zr, V, Ce) intermetallic compounds produces leached products of ZrO2, VO2, and CeO2 with Rhodium (Rh) as an active component. The characterization result reveals the HyTL process and the presence of the active Rh element that elevated the performance of HyTL-Al3Zr-Rh0.5 towards CO conversion compared to other samples. Further, the cubic ZrO2 phase selectively forms after HyTL at 130 °C even though the formation of the cubic ZrO2 phase takes place at a high temperature. Moreover, the presence of Rh promotes higher catalytic activity in all the cases with low temperatures. The advancement in the present study towards the catalytic oxidation of CO over the hydrothermally leached ZrO2-Rh nanocatalyst guarantees the perspective of the aggregation-activation process.

Effect of gradually decreasing laser power on the microstructure and properties of laser melting deposited Inconel 718Plus alloy thin-wall

Laser melting deposition (LMD) technology offers a novel method for fabricating superalloy thin-walled parts because of its significant advantage of rapidly producing near-net-shape moldings. However, the coarse columnar crystals in these deposited thin-walled parts resulted in poor mechanical properties, which significantly limited its wide application. To address this problem, a layer-by-layer decreasing laser power deposition strategy (LT) is proposed in this study, which can increase the cooling rate of the molten pool by reducing the thermal cycling. Results indicate that the thin walls of Inconel 718Plus alloy deposited by the LT strategy exhibit dendrites at heights of 4.5 mm (bottom region), 16.5 mm (middle region) and 28.5 mm (top region). The Laves phase at the bottom of the LT alloy thin-wall was randomly distributed granular, which gradually transformed into granular, short-chain and its mixed structures with increasing height. Formation of long-chain Laves phases was hindered by the connection of dendrites. The densely distributed granular Laves phase in the LT strategy alloy thin wall could effectively transfer and dispersed the stress and hindered the crack initiation and extended. Compared to the bottom region, the yield strength of the LT alloy thin-wall in the middle and top region increased by 6.7 % and 12.6 %, and the tensile strength increased by 10.7 % and 16.2 %. In conclusion, the alloy thin-walls fabricated by the LT strategy exhibit superior strength and more balanced mechanical properties.