Nitroaromatic Compounds Research Articles

Comparative study of NiO/CuO/Ag doped graphene based materials for reduction of nitroaromatic compounds and degradation of dye with statistical study

In the present work, the Nickel oxide (rGO–NiO), Silver (rGO–Ag), Copper oxide (rGO–CuO) doped Graphene Oxide are reported for catalytic reactions. A comparative study for catalytic activities of these materials are performed with nitroaromatic compound 4-nitroaniline and the results are statistically studied by using univariate analysis of variance and Post Hoc Test through Statistical Package for Social Sciences and it is observed that CuO doped Graphene material is showing better catalytic activity in minimum time. So, further research has been focused on the catalytic acitivity of rGO–CuO only and it is found that it is efficient in reducing other nitro compounds also such as Picric acid and Nitrobenzene. Dye degradation of Methylene blue is also performed using CuO decorated Graphene material and significant changes were observed using UV spectroscopy. The characterization of rGO–CuO is done with Fourier-transform Infrared Spectroscopy, Powder X-ray Diffraction, Thermogravimetric Analysis, Scanning Electron Microscope and Transmission Electron Microscopy.

Determination of 2,4,6 – trinitrotoluene in the soil samples around the Cu Chi Tunnel area by gas chromatography – mass spectrometry

During Vietnam War, nitroaromatic compounds such as 2,4,6-trinitrotoluene (TNT) have been widely used many kinds of explosive which bombed the immense network of connecting underground tunnels in Cu Chi District, Ho Chi Minh City, Vietnam. This study aims to optimize the method of using gas chromatography − mass spectrometry (GC-MS) to analyze TNT and then apply it to determine TNT in soil samples which collected around the Cu Chi area tunnels. In this experiment, ultrasonic was used to extract TNT from the soil samples to Acetonitrile before injecting 1µL sample solution into GC-MS. This method had linear concentration range of TNT from (5.0 to 500) ng/ g with limit of detection was 2.0 ng/g, the relative standard deviations of peak area were under 2.0 % and the recovery was from 80 % to 103 %. The results showed that TNT contamination in studied soil samples were not detected. ® 2023 Journal of Science and Technology - NTTU

Designing a calixarene-based {Zn24} coordination cage as a multifunctional sensor

Solvothermal method was chosen to construct a porous zinc-calixarene coordination cage (SWU-3): [Zn24(TC4A-SO2)6(BTC)8(H2O)6] (H4TC4A-SO2 = p-tert-butylsulfonylcalix[4]arene, H3BTC = 1,3,5-benzenetricarboxylic acid) by ZnCl2, H3BTC and H4TC4A-SO2. SWU-3 shows certain water stability and excellent luminescence property. In the fluorescence test, SWU-3 exhibits different fluorescence sensing behaviors for detecting Fe3+, CrO42-, Cr2O72- and iodine (I2), the LOD values are 2.21 × 10-5, 2.740 × 10-5, 3.066 × 10-5 and 6.673 × 10-6 mol/L, respectively. Moreover, nitroaromatic compounds (NACs) can also be detected by SWU-3. These results prove that SWU-3 reveals great potential as a fluorescence sensor for ions, I2 and NACs detection.

Decoration of viscose fibers with silver nanoparticle-based titanium-organic framework for use in environmental applications.

To effectively remove pharmaceuticals, nitroaromatic compounds, and dyes from wastewater, an efficient multifunctional material was created based on silver nanoparticles (Ag) and MIL-125-NH2 (MOF) immobilized on viscose fibers (VF) as a support substrate. Firstly, silver nanoparticles (Ag) were immobilized on the surface of viscose fibers (VF) via in situ synthesis using trisodium citrate (TSC) as a reducing agent to create (VF-Ag). Then, VF and VF-Ag were decorated with the titanium metal-organic framework MIL-125-NH2 (MOF) to create VF-MOF and VF-Ag-MOF. The influence of VF-Ag, VF-MOF, and VF-Ag-MOF on the sonocatalytic or sonophotocatalytic degradation of sulfa drugs was investigated. The results show that VF-Ag-MOF showed excellent sonocatalytic and sonophotocatalytic activity towards the degradation of sulfa drugs compared to VF-Ag and VF-MOF. Furthermore, sonophotodegradation showed a dramatic enhancement in the efficiency of degradation of sulfa drugs compared to sonodegradation. The sonophotodegradation degradation percentage of sulfanilamide, sulfadiazine, and sulfamethazine drugs in the presence of VF-Ag-MOF was 65, 90, and 95 after 45min of ultrasonic and visible light irradiation. The catalytic activity of VF-Ag, VF-MOF, and VF-Ag-MOF was evaluated through the conversion of p-nitrophenol (4-NP) to p-aminophenol (4-AP). The results demonstrate that VF-Ag-MOF had the highest catalytic activity, followed by VF-Ag and VF-MOF. The conversion percentage of 4-NP to 4-AP was 69%. The catalytic or photocatalytic effects of VF-Ag, VF-MOF, and VF-Ag-MOF on the elimination of methylene blue (MB) dye were investigated. The results demonstrate that VF-Ag-MOF showed high efficiency in removing the MB dye through the reduction (65%) or photodegradation (71%) after 60min. VF-Ag-MOF composites structure-activity relationships represent that doping within silver NPs enhanced the photocatalytic activity of MIL-125-NH2, which could be explained as follows: (i) Due to the formation of a Schottky barrier at the junction between MIL-125-NH2 and Ag NPs, the photogenerated electrons in the conduction band of MIL-125-NH2 were supposed to be quickly transferred to the valence band of the Ag NPs, and subsequently, the electrons were transferred to the conduction band of Ag NPs. This considerable electron transferring process, which is reported as Z scheme heterojunction, can efficiently suppress the recombination of electron/hole pairs in VF-Ag-MIL-125-NH2 composites. (ii) Sufficient separation between the photogenerated charge carriers (holes and electrons) and avoiding their recombination enhanced the photocatalytic activity of composites.

Multifunctional Luminescent 3D Ln-MOFs with High Sensitivity for Trace Detection of Micronutrients.

The synthesis of two versatile fluorescent metal-organic frameworks (MOFs), [Eu(4-NCP)(1,4-bdc)]n·0.5H2O (1) and [Eu(4-NCP)(4,4'-bpdc)]n·0.75H2O (2) (HNCP = 2-(4-carboxyphenyl)imidazo(4,5-f)-(1,10)phenanthroline, 1,4-H2bdc = benzene-1,4-dicarboxylic acid, 4,4'-H2bpdc = 4,4'-biphenyldicarboxylic acid), was carried out using a hydrothermal method. These MOFs were characterized through various advanced technologies to determine their structural information. The results indicate that both MOFs exhibited 3D network structures with specific topologies. Furthermore, these MOFs demonstrated exceptional thermal stabilities and adsorption capabilities. Additionally, complex 2 was utilized for studying the fluorescence sensing properties of various micronutrients including metal ions, nitro aromatic compounds, and biological small molecules. Notably, complex 2 showed promising potential as a multifunctional sensor for selectively detecting Fe3+, nitrobenzene, and ascorbic acid in aqueous solutions through fluorescence quenching with low limits of detection (LODs ∼ 10-7 M) and high quenching constants (Ksv ∼ 103 M-1). Moreover, the detection mechanism of complex 2 was further investigated by using experimental methods and DFT calculations.

Enhanced Stability and Catalytic Activity of a Nanocatalyst with Reusable Ionic Liquid Hydrogels for the Reduction of Organic Pollutants.

Nitroaromatic compounds have a wide range of applications. However, they pose a significant threat to both the environment and human health. Ionic liquid hydrogels (ILs-gels) have emerged as a cost-effective and environmentally friendly option for various applications. However, conventional ILs-gels are known to possess mechanical flaws or defects. The procedure utilized a facile synthesis route that involved the polymerization of acrylamide (AM) and ionic liquids (ILs) to create a novel candidate for nanoparticle absorption. This study resolved this issue by creating toughened hydrophobic combined hydrogels synthesized through the addition of SiO2@poly(butyl acrylate) core-shell inorganic-organic hybrid latex particles (SiO2@PBA) to the AM-ILs mixture. The SiO2@PBA particles were chosen to provide the hydrogels with exceptional stretchability (up to 4050% strain) and high mechanical properties (tensile strength of 126 kPa) by acting as both a nanotoughener and a cross-linking point for hydrophobic linkage. Additionally, the P(AM/ILs)-SiO2@PBA hydrogel served as a template for the in situ and stable formation of palladium (Pd) nanoparticles. By incorporation of these Pd nanoparticles as catalysts into P(AM/ILs)-SiO2@PBA hydrogel carriers, the resulting P(AM/ILs)-SiO2@PBA/Pd hydrogels exhibited the ability to catalyze the degradation of p-nitrophenol. Remarkably, even after 15 applications, the efficiency of the degradation process remained consistently above 90%. Thus, the innovative SiO2@PBA toughened ILs-hydrogel design strategy can be utilized to develop robust and stretchable hydrogel materials for catalytic use in the sewage disposal industry.

One-pot Construction of Metal Nanoparticles Loaded COF Catalysts for Aqueous Hydrogenation Reactions.

The catalysis performance of metal nanoparticles (NPs) will be significantly deteriorated because of their spontaneous agglomeration during practical applications. Covalent-organic frameworks (COFs) materials with functional groups and well-defined channels benefit for the dispersion and anchor of metal ions and the confined growth of metal NPs, working as an ideal platform to compose catalytic systems. In this article, we report a one-pot strategy for the preparation of metal NPs loaded COFs without the need of post-modification. During the polymerization process, the pre-added metal ions were stabilized by the rapidly formed COF oligomers and hardly disturb the construction of COFs. After reduction, metal NPs are uniformly anchored on the COF matrix. Eventually, a wide spectrum of metal NPs, including Au, Pd, Pt, AuPd, CuPd, CuPt and CuPdPt, loaded COFs are successfully prepared. The versatility and metal ions anchoring mechanism are verified with four different COF matrixes. Taking AuPd NPs as example, the resultant AuPd NPs loaded COF materials can selectively decompose ammonium formate and produce hydrogen in-situ, exhibiting over 99 % conversion of hydrodechlorination for chlorobenzenes and nitro-reduction reaction for nitroaromatic compounds under ambient temperature in aqueous solution.

Selective detection of explosive nitro-aromatic compounds using the 2D organic nanosheets (2DONs) synthesize via 2D click chemistry directed by ultrasonication

Recent advancements in click chemistry have made it an effective method for quickly and easily assembling extremely stable nanomaterial assemblies onto surfaces. Therefore, a new class of fluorescent sensor utilizing two-dimensional organic nanosheets (2DONs) for the selective sensing of 2,4-dinitrophenylhydrazine (2,4-DNPH) has been proposed by using the click chemistry directed by the probe ultrasonication method (CCDPS) which is driven by the π-π stacking interactions with the aid of DMF solvent. Prolonged human exposure to 2, 4-DNPH has been associated with various detrimental health consequences, including skin conditions, liver issues, and disturbances to the central nervous and cardiovascular systems. Fluorescence titration tests with nanomolar scale limit of detection (LOD, 100 nM or 0.1 μM) and limit of quantification (LOQ, 0.4 μM) for 2,4-DNPH showed fluorescence quenching reactions and excellent reversibility. Additionally, zeta potential and UV-absorption spectroscopy were used to validate the interaction and binding characteristics of 2D ONs with 2,4-DNPH. In contrast to the widely reported ground-state charge transfer or FRET-based probes for nitroaromatics detection, the signal response for 2,4-DNPH was achieved by a strong inner filter effect with the combination of FRET (IFE-FRET).

Simultaneous determination of six nitroaromatic compounds and three anions in environmental matrices using a liquid chromatography-ion chromatography coupled system

Nitroaromatic compounds are used extensively in various fields such as dyes, pesticides, spices, pharmaceuticals, and explosives. However, the residual raw materials of these compounds accumulate in the environment and pose serious risks to human health. Chronic exposure to low concentrations of nitroaromatic compounds can cause anemia, cancer, and organ damage. Currently, Fenton oxidation and natural bioremediation are the processes most often used to eliminate nitroaromatic compounds from environmental water and soil. According to previous research, the presence of inorganic anions such as chloride, nitrite, and nitrate ions in the environmental matrix exerts an inhibitory effect on the biodegradation of nitroaromatic compounds. Furthermore, high nitrate levels in drinking water can lead to the production of nitrosamine carcinogens, which affect ecological safety and human health, in water bodies. Thus, the simultaneous determination of nitroaromatic compounds and chloride, nitrite, and nitrate ions in environmental soil and water matrices is critical for selecting appropriate nitroaromatic compound degradation methods and monitoring surface water quality. Traditional detection methods require two sample pretreatment steps and two instrumental analytical techniques to determine nitroaromatic compounds and inorganic anions in environmental matrices; moreover, these methods are time consuming, labor intensive, and error prone. Therefore, in this study, a method that combines high performance liquid chromatography (HPLC) and ion chromatography (IC) was developed to simultaneously detect nitroaromatic compounds and anions in environmental matrices. In this method, sample enrichment was achieved through bulk injection and enrichment column collection, which greatly simplified the pretreatment process. The HPLC instrument was connected to the IC instrument using two six-way valves and an enrichment column. The system operation can be divided into four stages: (A) sample loading to the quantitative ring, (B) separation of nitroaromatic compounds and anions, (C) enrichment of anions in an AG20 column, and (D) simultaneous determination of nitroaromatic compounds and anions by HPLC and IC, respectively. The time of the anions flowing out of the C18 column was determined by directly connecting the C18 column to a conductivity detector. Based on the retention times of the anions, the switching time of the six-way valve was optimized to ensure that the anions completely entered the IC column, thereby ensuring the accuracy of the method. During the chromatographic analysis stage, nitroaromatic compounds were separated and analyzed by HPLC system with a mobile phase composed of potassium phosphate buffer (pH 7.0) and acetonitrile (60∶40, v/v) at a flow rate of 1.0 mL/min; in the IC system, the anions were separated and analyzed using a 20 mmol/L sodium hydroxide aqueous solution as the mobile phase under a suppression current of 50 mA. Both anions and nitroaromatic compounds exhibited strong linear correlations within certain concentration ranges, with correlation coefficients greater than 0.993. The recoveries of the nitroaromatic compounds and anions ranged from 88.20% to 105.38% at three spiked levels, with relative standard deviations ranging from 2.0% to 11.5%. The contents of six nitroaromatic compounds and three anions in five surface water and five soil samples were determined using the developed method. Although no nitroaromatic compounds were detected in these samples, the three anions were detected at contents ranging from 0.41 to 55.3 mg/L in surface water samples, and 0.56 to 30.2 mg/kg in soil samples. Methodological validation and actual sample detection demonstrated that the proposed method has a high degree of automation, simple operation, good repeatability, high accuracy, wide applicability, and high sensitivity. Thus, this method is suitable for the rapid determination of chloride, nitrite, nitrate ions and nitroaromatic compounds in soil and water and can be extended to the simultaneous determination of inorganic ions and organic matters in other samples.

Carbon nanodots from orange peel waste as fluorescent probes for detecting nitrobenzene

An integrated approach combining thermal and electrochemical technologies for the valorization of agro-industrial waste. The resulting carbon dots (CDs) show fascinating optical properties, enabling their application as fluorescent chemical probes.

Cu-containing polyoxometalate-based melamine in the environmental remediation of toxic organic pollutants

Green, simple, and efficient synthesis of transition metal substituted Keggin-type polyoxometalates-based melamine and their application in the catalytic reduction of some toxic pollutants such as nitro aromatic compounds and organic dyes.

Application of cold-adapted microbial agents in soil contaminate remediation: biodegradation mechanisms, case studies, and safety assessments.

The microbial agent technology has made significant progress in remediating nitro-aromatic compounds (NACs), such as p-nitrophenol, 2,4-dinitrophenol, and 2,4,6-Trinitrotoluene, in farmland soil over the past decade. However, there are still gaps in our understanding of the bioavailability and degradation mechanisms of these compounds in low-temperature environments. In this review, we provide a comprehensive summary of the strategies employed by cold-adapted microorganisms and elucidate the degradation pathways of NACs pollutants. To further analyze their metabolic mechanisms, we propose using mass balance to improve our understanding of biochemical processes and refine the degradation pathways through stoichiometry analysis. Additionally, we suggest employing 13C-metabolic flux analysis to track enzyme activity and intermediate products during bio-degradation processes with the aim of accelerating the remediation of nitro-aromatic compounds, particularly in cold regions. Through a comprehensive analysis of pollutant metabolic activities and a commitment to the 'One Health' approach, with an emphasis on selecting non-pathogenic strains, the environmental management strategies for soil remediation could be positioned to develop and implement safe and effective measure.

Using eugenol scaffold to explore the explosive sensing properties of Cd(II)-based coordination polymers: experimental studies and real sample analysis.

Eugenol, the major constituent of clove oil, has been explored as an essential natural ingredient for ages owing to its versatile pharmacological properties. However, to date, the coordination chemistry of eugenol derivatives has not been much explored. In the present work, an eugenol-based Schiff base ligand (HL) was synthesized and structurally confirmed through ESI-MS, NMR, and FT-IR spectroscopy studies. Consequently, the N,O-donor chelating ligand HL was coordinated with Cd2+, in the presence of bridging pseudohalides (thiocyanate, SCN-, and dicyanamide, N(CN)2-) to synthesize two luminescent coordination polymers (CPs 1 and 2): [Cd2(L)2(X)2]n (where HL = 4-allyl-2-(((2-(benzylamino)ethyl) imino)methyl)-6-methoxyphenol and Xs are bridging pseudohalides, i.e., SCN- and N(CN)2-) on a Cd-eugenol scaffold. The CPs depicted structural diversity, bulk-phase purity, thermal stability, and the presence of interlayer supramolecular C-H⋯π interactions together with C-H⋯S (for CP 1) and C-H⋯N (for CP 2) interactions. The CPs further exemplified themselves as selective and sensitive 'turn-off' probes towards trinitrophenol (TNP) (quenching efficiency: 82.02% and 83.86% for 1 and 2) among a pool of hazardous nitroaromatic compounds (NACs). Accordingly, 1 and 2 exhibited an ultralow limit of detection (LOD) of 0.29 and 0.15 μM, with high quenching constants (KSV) of 5.91 × 104 and 17.60 × 104 M-1, respectively. In addition, TNP sensing events were evidenced to be recyclable and exhibited fast response (∼31 s, 1, and ∼40 s, 2), which increased its real-world viability. Vapor phase TNP sensing was also accomplished upon drop-casted CP films. Experimental investigations and theoretical DFT study confirmed the cooperative occurrence of RET-IFE-PET-collisional quenching and non-covalent π⋯π stacking as key factors involved in the TNP sensing performance. The competency of 1 and 2 in the detection of TNP from several complex environmental matrices (CEMs), viz. matchstick powder, river and sewage water, and soil specimens, was also established with good recovery (∼66-86% and ∼68-93% for 1 and 2, respectively) and high KSV values (3.90-11.39 × 104 and 6.17-18.79 × 104 M-1 for 1 and 2, respectively).

Comparative Study of Luminescent Cd-MOF and Cd-MOF@HNT Nanomaterial for detection of Hydroxyl-Functionalized Nitroaromatic compounds

Comparative Study of Luminescent Cd-MOF and Cd-MOF@HNT Nanomaterial for detection of Hydroxyl-Functionalized Nitroaromatic compounds

Photo-induced microfluidic production of ultrasmall platinum nanoparticles.

We describe here the synthesis of ultrasmall Pt nanoparticles (NPs) obtained by a robust and reliable protocol using UV-Vis photoreduction of a platinum salt precursor, under continuous flow conditions. These ligand-free Pt NPs were rapidly dispersed onto a solid support or stabilized towards aggregation as a colloidal solution by the addition of an appropriate ligand in the reaction mixture. The proposed protocol exploits a microfluidic platform where the Pt4+ precursor is photo-reduced to small Pt0 NPs (1.3 nm) at room temperature in the presence of ethanol, without any additional reducing agent. We apply the protocol to prepare Pt NPs highly dispersed on carbon support (Pt/C) proven to be a very efficient heterogeneous catalyst for both the hydrosilylation of terminal alkynes and hydrogenation of nitroaromatic compounds, selected as model reactions. Furthermore, we exploit the versatility of this microfluidic approach to produce stabilized aqueous/ethanol colloidal solutions of Pt NPs, employing a ligand of choice (e.g., PVP or a thiol-ligand). These colloids offer long-term storage and further ligand modification. We showcase the synthesis of biocompatible glycol-stabilized Pt nanoparticles as an exemplary application.

Facile construction of an anthracene-decorated highly luminescent coordination polymer for the selective detection of explosive nitroaromatics and the mutagenic pollutant TNP.

Explosive nitroaromatic compounds (epNACs) are a group of chemicals that have caused significant human casualties through terrorist attacks and they also pose health risks. For the benefit of homeland security and environmental health, there is room for advancing research on the precise detection of epNACs. Coordination polymers (CPs) successfully serve this purpose because of their binding abilities and quenching capabilities. In this regard, a one-dimensional (1D) CP [Zn(bdc)(avp)2(H2O)]n (1; H2bdc = 1,4-benzenedicarboxylic acid and avp = 4-[2-(9-anthryl)vinyl]pyridine) was synthesized, which remarkably demonstrated extremely efficient ratiometric and selective sensing capacity toward epNACs and the mutagenic pollutant 2,4,6-trinitrophenol (TNP) with a quick response. Density functional theory (DFT) calculations provided a thorough analysis of the mechanistic routes behind the quenching reaction. Herein, geometrically accessible interaction sites were strategically decorated using anthracene moieties, allowing the quick and precise detection of explosive nitro derivatives and the carcinogenic pollutant TNP with increased sensitivity.

Active site-exposed Bi2WO6@BiOCl heterostructures for photocatalytic hydrogenation of nitroaromatic compounds.

Constructing heterostructured photocatalysts with highly exposed active sites proves to be an efficient strategy to improve the photocatalytic performance of bismuth-based photocatalysts. In this work, active site-exposed Bi2WO6@BiOCl (BWO@BOC) heterostructure composites based on two bismuth-based materials were fabricated by an in situ growth method for improving the photocatalytic hydrogenation of 4-aniline (4-NA) to p-phenylenediamine (PPD). BWO@BOC exhibited enhanced photoactivity for 4-NA hydrogenation compared to pure BWO and BOC. The optimal BWO@BOC composites displayed the highest conversion rate of 4-NA to PPD up to 99.3% within 12 min, with an apparent reaction rate constant of 0.414 min-1, which is 3.3 times that of pure BOC. The photoactivity enhancement is mainly ascribed to the construction of a tight Z-scheme heterostructure with improved light harvesting properties and charge carrier transport efficiency, which were revealed by optical and photoelectrochemical characterization, respectively. Furthermore, the products of the hydrogenation process were monitored by in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) to gain a better insight into the 4-NA hydrogenation mechanism.

Characterization of O2 uncoupling in biodegradation reactions of nitroaromatic contaminants catalyzed by rieske oxygenases.

Rieske oxygenases are known as catalysts that enable the cleavage of aromatic and aliphatic C-H bonds in structurally diverse biomolecules and recalcitrant organic environmental pollutants through substrate oxygenations and oxidative heteroatom dealkylations. Yet, the unproductive O2 activation, which is concomitant with the release of reactive oxygen species (ROS), is typically not taken into account when characterizing Rieske oxygenase function. Even if considered an undesired side reaction, this O2 uncoupling allows for studying active site perturbations, enzyme mechanisms, and how enzymes evolve as environmental microorganisms adapt their substrates to alternative carbon and energy sources. Here, we report on complementary methods for quantifying O2 uncoupling based on mass balance or kinetic approaches that relate successful oxygenations to total O2 activation and ROS formation. These approaches are exemplified with data for two nitroarene dioxygenases (nitrobenzene and 2-nitrotoluene dioxygenase) which have been shown to mono- and dioxygenate substituted nitroaromatic compounds to substituted nitrobenzylalcohols and catechols, respectively.

Synthesis of two-dimensional bismuth molybdenum oxide (2D-BMO) nanosheets and their application as fluorescent probes for the detection of explosive nitroaromatic compounds

2D-BMO fluorescent nanosheets were synthesized using a solvothermal method followed by probe sonication.

Selective sensing of picric acid using a Zn(II)-metallacycle: experimental and theoretical validation of the sensing mechanism and quantitative analysis of sensitivity in contact mode detection.

A combination of N,N',N''-tris(3-pyridyl)-1,3,5-benzenetricarboxamide (L1) and p-chlorobenzoic acid (HL2) with Zn(NO3)2·6H2O resulted in the formation of a dinuclear metallacycle [ZnL1(L2)2(DMF)2]2 (1(DMF)4). In 1(DMF)4, the Zn(II) centre adopts a square pyramidal geometry, while one of the pyridyl N out of the three pyridyl groups in L1 remained uncoordinated. Solvated DMF molecules are present in 1(DMF)4. The structural and chemical nature of 1(DMF)4 is effective for it to act as a potential fluorescent probe for the detection of nitroaromatic compounds. It is observed that the probe, 1(DMF)4, could selectively detect picric acid (PA) among various aromatic compounds in solution (DMSO), while the solid state (contact mode) detection showed a positive sensing response for the nitrophenols (PA: 87% quenching efficiency, 2,4-dinitrophenol (2,4-DNP): 57% quenching efficiency and 4-nitrophenol (4-NP): 40% quenching efficiency). The limit of detection (LOD) of PA by the probe in DMSO was found to be 6.8 × 10-11 M while the LOD in contact mode detection was estimated to be 0.49 ng cm-2. The mechanism of selective detection of PA by 1(DMF)4 in DMSO was analyzed through photophysical studies, 1H-NMR experiments and also by density functional theory (DFT) calculations. The effective overlap of the absorption spectrum of 1(DMF)4 and emission spectrum of PA in DMSO suggests that the Förster resonance energy transfer (FRET) is responsible for quenching phenomena in DMSO. The DFT calculations and molecular docking studies showed the adduct formation due to the favorable interactions between 1(DMF)4 and PA in DMSO, while negligible interactions were observed between 1(DMF)4 with other aromatic compounds. The experimental and DFT studies showed that the efficient sensing ability of PA by 1(DMF)4 in the solid-state was due to photoelectron transfer (PET) and FRET phenomena described herein.