Multi-anode Photomultiplier Tube Research Articles

Upgrade of the LHCb RICH detectors and characterization of the new opto-electronics chain

The LHCb detector has been upgraded to manage a five-fold increase in the instantaneous luminosity delivered to the experiment during LHC Run 3 and to readout data at the full bunch crossing rate of 40 MHz. The enhanced LHCb RICH detectors now feature Multianode Photomultiplier Tubes (MaPMTs), covering a total area of approximately 4 square meters, and brand-new frontend electronics to comply with the trigger-less readout architecture. The opto-electronics chain is capable of detecting single photons at repetition rates of up to 100 MHz/cm2 while maintaining an exceptionally low noise. The RICH upgrade is comprehensively outlined, including details about the characterization and studies on the photon detection system. The stability and uniformity achieved by optimizing the parameters of the opto-electronics chain enable the RICH system to function successfully and to provide excellent charged hadron identification in high occupancy conditions.

Measurement of Naturally-Occurring Radioactive Materials (NORM) using a scintillator-based alpha detector

It is important to differentiate between natural and artificial radioactive materials such as plutonium in nuclear facilities. In this study, a scintillator-based alpha-particle detector was developed using YAP:Ce scintillator and Multi-Anode PhotoMultiplier Tube. The detector was used to measure various naturally occurring radioactive materials (NORM) samples including radon progeny, lead plate, lantern mantle, and radium ceramic ball. The measurement results were compared with Monte Carlo simulation calculations and were found to be in agreement. The energy resolution of the detector is 8.6%FWHM. In the measurement results of radon progeny, peaks of 212Bi (6.1 MeV), 214Po (7.7 MeV), and 212Po (8.8 MeV) can be observed. The lead plate contains 210Po and emits 5.3 MeV alpha particle. The simulation with the same energy was able to reproduce the actual measurement. The results showed the energy and distribution of the alpha particles emitted by the NORM samples. The study successfully demonstrated the capability of the developed alpha-particle detector in identifying NORM.

A computing module for speeding up the bunch-by-bunch measurement of transverse positions and transverse profiles within injection period

The Multi-Bend-Achromat (MBA) structure of the Diffraction-limited Synchrotron Light Source (DLSR) makes the dynamic range of its injection significantly smaller, thus posing a more demanding challenge for the stable injection of beams. To investigate the possible instabilities during the injection process, multi-anode photomultiplier tubes (MAPMT) are used in bunch-by-bunch measurements to obtain the transverse positions and transverse profiles of the bunched beams as they are injected. However, the data processing time witnessed in prior measurements posed a significant challenge in obtaining this information in time, thus failing to meet the stringent demands of online measurements. Consequently, this paper proposes one computing module, engineered to enhance the speed of bunch-by-bunch measurements of transverse positions and profiles. This solution is capable of delivering measurement results for each bunch in the filling pattern, all within the specified injection period.

Spectroradiometry with sub-microsecond time resolution using multianode photomultiplier tube assemblies.

Accurate and precise measurements of spectroradiometric temperature are crucial for many high pressure experiments that use diamond anvil cells or shock waves. In experiments with sub-millisecond timescales, specialized detectors such as streak cameras or photomultiplier tubes are required to measure temperature. High accuracy and precision are difficult to attain, especially at temperatures below 3000K. Here, we present a new spectroradiometry system based on multianode photomultiplier tube technology and passive readout circuitry that yields a 0.24 µs rise-time for each channel. Temperature is measured using five color spectroradiometry. During high pressure pulsed Joule heating experiments in a diamond anvil cell, we document measurement precision to be ±30 K at temperatures as low as 2000K during single-shot heating experiments with 0.6 µs time-resolution. Ambient pressure melting tests using pulsed Joule heating indicate that the accuracy is ±80 K in the temperature range 1800-2700K.

Mini-EUSO on Board the International Space Station: Mission Status and Results

The telescope Mini-EUSO has been observing, since 2019, the Earth in the ultraviolet band (290–430 nm) through a nadir-facing UV-transparent window in the Russian Zvezda module of the International Space Station. The instrument has a square field of view of 44°, a spatial resolution on the Earth surface of 6.3 km and a temporal sampling rate of 2.5 microseconds. The optics is composed of two 25 cm diameter Fresnel lenses and a focal surface consisting of 36 multi-anode photomultiplier tubes, 64 pixels each, for a total of 2304 channels. In addition to the main camera, Mini-EUSO also contains two cameras in the near infrared and visible ranges, a series of silicon photomultiplier sensors and UV sensors to manage night-day transitions. Its triggering and on-board processing allow the telescope to detect UV emissions of cosmic, atmospheric and terrestrial origin on different time scales, from a few microseconds up to tens of milliseconds. This makes it possible to investigate a wide variety of events: the study of atmospheric phenomena (lightning, transient luminous events (TLEs) such as ELVES and sprites), meteors and meteoroids; the search for nuclearites and strange quark matter; and the observation of artificial satellites and space debris. Mini-EUSO is also potentially capable of observing extensive air showers generated by ultra-high-energy cosmic rays with an energy above 1021 eV and can detect artificial flashing events and showers generated with lasers from the ground. The instrument was integrated and qualified in 2019 in Rome, with additional tests in Moscow and final, pre-launch tests in Baikonur. Operations involve periodic installation in the Zvezda module of the station with observations during the crew night time, with periodic downlink of data samples, and the full dataset being sent to the ground via pouches containing the data disks. In this work, the mission status and the main scientific results obtained so far are presented, in light of future observations with similar instruments.

Development of contamination detection system combined with various remote devices

The detection of alpha and beta contamination locations is important for decontaminating nuclear facilities. In the high radiation dose rate environment at the decommissioning sites, the contamination measurement by the workers is not effective. Thus, we developed a remote automatic contamination measurement system using a new scintillator-based detector. A 50 mmφ × 100-μm-thick YAlO3(Ce)(YAP:Ce) scintillator was coupled with a flat panel-type multianode photomultiplier tube. The detector was installed downwards at the bottom of a robot. It has an energy measurement capability, and the energy measurement could discriminate the alpha particles from the beta and 222Rn alpha particles. With the energy information, alpha and beta particles could be identified and mapped simultaneously. In addition, a slow-moving robot could be used to obtain statistically sufficient counts in a single run measurement, allowing the evaluation of surface contamination density using only alpha particles. The remote automatic contamination measurement system will be useful in visualizing the contamination distribution in environments that are inaccessible to workers.

Use of Silicon Photomultipliers in the Detectors of the JEM-EUSO Program

The JEM-EUSO program aims to study ultra-high energy cosmic rays from space. To achieve this goal, it has realized a series of experiments installed on the ground (EUSO-TA), various on stratospheric balloons (with the most recent one EUSO-SPB2), and inside the International Space Station (Mini-EUSO), in light of future missions such as K-EUSO and POEMMA. At nighttime, these instruments aim to monitor the Earth’s atmosphere measuring fluorescence and Cherenkov light produced by extensive air showers generated both by very high-energy cosmic rays from outside the atmosphere and by neutrino decays. As the two light components differ in duration (order of microseconds for fluorescence light and a few nanoseconds for Cherenkov light) they each require specialized sensors and acquisition electronics. So far, the sensors used for the fluorescence camera are the Multi-Anode Photomultiplier Tubes (MAPMTs), while for the Cherenkov one, new systems based on Silicon PhotoMultipliers (SiPMs) have been developed. In this contribution, a brief review of the experiments is followed by a discussion of the tests performed on the optical sensors. Particular attention is paid to the development, test, and calibration conducted on SiPMs, also in view to optimize the geometry, mass, and weight in light of the installation of mass-critical applications such as balloon- and space-borne instrumentation.

Development of the segmented plastic scintillation detector GARi for studying $r$-process nucleosynthesis at RIBF

\(\beta\)-decay properties of very neutron-rich nuclei, such as the half-life and the \(\beta\)-delayed neutron emission probabilities, play an essential role in the astrophysical rapid neutron capture process (r-process), where elements heavier than iron may be synthesized. Investigating those crucial properties has been one of the main objectives of the experimental programs at the RIKEN RI Beam Factory (RIBF). Recently, the development of a fast-timing detector system comprising a highly segmented plastic scintillation detector GARi (Gas-cell Active detector for Radioisotope decay), a neutron time-of-flight detector array, and a LaBr\textsubscript{3} detector array is being conducted for the measurement of \(\beta\)-delayed neutron emission and other related \(\beta\)-decay properties of neutron-rich nuclei at the F11 decay station of RIBF. The GARi detector has been constructed from a fast, segmented plastic scintillator coupled with nine multi-anode photomultiplier tubes (PMTs), resulting in enhanced position sensitivity. Therefore, this detector can be employed as an implantation detector and can also serve as a trigger signal in neutron time-of-flight experiments. This work details the development of the GARi detector and the results tested with the radioactive sources.

Fast-sampling fast-ion D-alpha measurement using multi-anode photomultiplier tube in large helical device.

A fast-sampling fast-ion D-alpha (F-FIDA) measurement has been developed in the large helical device in order to investigate fast ion dynamics associated with helically trapped fast-ion-driven Magnetohydrodynamic (MHD) bursts. F-FIDA consists of a multi-anode photomultiplier tube (PMT) and achieves a sampling rate of 10kHz. During the deuterium experiment campaign in 2022, F-FIDA measured the spectrum of perpendicular fast ions, using perpendicular lines of sight. We compared F-FIDA with conventional FIDA, using an electron multiplying charge coupled device, and confirmed that the time-averaged images were generally consistent between the two. The statistical properties of the temporal evolution associated with MHD bursts were analyzed using a conditional sampling technique. The results showed that the PMT signal varied in different spatial and wavelength channels. Although the signal-to-noise ratio was poor and there was room for improvement, it could provide useful information for studies on the phase-space dynamics of fast ions.

The JUNO experiment Top Tracker

The main task of the Top Tracker detector of the neutrino reactor experiment Jiangmen Underground Neutrino Observatory (JUNO) is to reconstruct and extrapolate atmospheric muon tracks down to the central detector. This muon tracker will help to evaluate the contribution of the cosmogenic background to the signal. The Top Tracker is located above JUNO’s water Cherenkov Detector and Central Detector, covering about 60% of the surface above them. The JUNO Top Tracker is constituted by the decommissioned OPERA experiment Target Tracker modules. The technology used consists in walls of two planes of plastic scintillator strips, one per transverse direction. Wavelength shifting fibres collect the light signal emitted by the scintillator strips and guide it to both ends where it is read by multianode photomultiplier tubes. Compared to the OPERA Target Tracker, the JUNO Top Tracker uses new electronics able to cope with the high rate produced by the high rock radioactivity compared to the one in Gran Sasso underground laboratory. This paper will present the new electronics and mechanical structure developed for the Top Tracker of JUNO along with its expected performance based on the current detector simulation.

Characterisation and operations of the Multianode Photomultiplier Tubes for the LHCb RICH detectors

The upgraded LHCb RICH detectors are equipped with Multianode Photomultiplier Tubes, covering a total area of approximately four square metres. In order to achieve the same excellent hadron identification performance as during LHC Runs 1 and 2 at five times the instantaneous luminosity, the photon detectors have to be sensitive to single photons with repetition rates of up to 100MHz/cm2 and to have a very low noise count rate. The main properties of the photomultipliers are presented, together with the characterisation of an unexpected source of noise observed in the Hamamatsu R11265 Multianode Photomultiplier Tubes, extending up to several microseconds after the primary signal. The quality control results, the mitigation strategies for the aforementioned noise to perform optimal single-photon counting at 40 MHz, and the first operations of the RICH system are described.

A novel fast-timing readout chain for LHCb RICH LS3 and prototype beam tests

The prompt Cherenkov radiation and focusing optics of the LHCb RICH detectors allow the prediction of the Cherenkov photon detection time from a given charged particle to within 10ps. Fast-timing information on the detected Cherenkov photons can therefore be used to significantly improve the particle identification (PID) performance and the signal-to-background ratio of the detectors. This concept is a cornerstone for the LHCb RICH detector upgrades and will ultimately allow the system to operate at a luminosity in excess of 1034cm−2s−1 during HL-LHC Run 5. A new electronic readout chain is proposed for the LHC Long Shutdown 3 (LS3, 2026-2028) using the FastRICH, a novel ASIC under development. The specifications for the FastRICH are discussed in the context of the LS3 enhancements and LHCb Upgrade II. The FastRICH will perform multi-channel single-photon discrimination, timestamp photons with 25 ps bin size, integrate closely with the LHCb optical link chipset and apply data-compression techniques. The detector will be capable of timestamping each photon with 150ps resolution dominated by the existing Multianode Photomultiplier Tube (MAPMT) transit-time spread. The new electronic readout chain introduces important timing and detector techniques ahead of the Upgrade II RICH system overhaul and the FastRICH has the flexibility to be coupled to sensors with better time resolution for HL-LHC Run 5. Simulation studies have demonstrated improvements in the hadronic PID performance during Run 4 using the FastRICH coupled to MAPMTs. A first version of the readout chain, based on the FastIC, a predecessor of the FastRICH, and a TDC-in-FPGA, has been studied using Cherenkov photons at the CERN SPS charged particle beam test facility.

Quality assurance for the LHCb RICH upgrade Photon-Detection chain

During the Long Shutdown 2 of the LHC, the LHCb RICH system has undergone an upgrade to implement the LHCb trigger strategy which increased the read-out rate from 1 MHz to 40 MHz. The new challenging operating conditions of the upgraded experiment required the replacement of the Hybrid Photon Detectors with Multi-Anode Photomultiplier tubes (MaPMT) and the introduction of new customised front-end electronics. The new RICH detectors have a modular design to facilitate maintenance and assembly. The fundamental core element is the Elementary Cell (EC), which is composed of one or four MaPMTs, depending on the type of the MaPMT, and the associated front-end electronics. An overview of the protocols and testing facilities which have been designed and put in place to perform the quality assurance programme is presented. This process lasted more than six years and included the testing and characterisation of the new front-end electronics, the MaPMTs, the ECs, and the photon detector assembly (columns), commissioning, and installation of the columns in the LHCb cavern.

Upgrade of the scintillator detector for particle tracking in experiments with antiprotons

Experiments with antiprotons often require the tracking of charged particles emerging from the annihilation process. The Atomic Spectroscopy And Collisions Using Slow Antiprotons (ASACUSA) collaboration at the CERN Antiproton Decelerator (AD) used several panels of scintillating bars placed around the interaction region to detect the passage of charged pions and determine the annihilation vertex position and time. The panels were composed by extruded scintillating bars and the light was collected using WaveLength Shifting (WLS) fibers and multi-anode PhotoMultiplier Tubes (PMTs). After operating for several years, the fiber-PMT coupling quality had degraded and a major upgrade of the light readout system was planned. The PMTs will be replaced by Silicon PhotoMultipliers (SiPMs) and the front-end electronics changed accordingly. An improvement is expected in the efficiency and the uniformity of the detector response. In this contribution the commissioning of the upgrade will be described, including the results of preliminary tests with cosmic rays.

The upgrade of the ASACUSA scintillating bar detector for antiproton annihilation measurements

Antiproton annihilations on matter nuclei are usually detected by tracking the charged pions emitted in the process. A detector made of plastic scintillating bars have been built and used in the ASACUSA experiment for the last 10 years. Ageing, movements and transports caused stress on the internal mechanical structure and impacted mostly on the optical readout system which was eventually upgraded: the so far used multi-anode photo-multiplier tubes (PMTs) have been replaced by silicon photomultipliers (SiPM) and the front-end electronics had to be adapted to cope with the new signal formation. This work describes the design and operations of the upgrade, as well as the validation tests with cosmic rays.

Integration, qualification, and launch of the Mini-EUSO telescope on board the ISS

Mini-EUSO is a high-sensitivity imaging telescope that observes the Earth from the ISS in the near ultraviolet band (290 $$\div$$ 430 nm), through the nadir-facing, UV-transparent window in the Russian Zvezda module. The instrument, launched in 2019, has a field of view of 44 $$^{\circ }$$ , a spatial resolution on the Earth’s surface of 6.3 km and a temporal sampling rate of 2.5 microseconds. Thanks to its triggering and on-board processing, the telescope is capable of detecting UV emissions of cosmic, atmospheric, and terrestrial origin on different time scales, from a few microseconds up to tens of milliseconds. The optics is composed of two Fresnel lenses focusing light onto an array of 36 Hamamatsu Multi-Anode PhotoMultiplier Tubes, for a total of 2304 pixels. The telescope also contains two cameras in the near-infrared and visible, an 8-by-8 array of Silicon-PhotoMultipliers and a series of UV sensors to manage night-day transitions. The scientific objectives range from the observation of atmospheric phenomena [lightning, Transient Luminous Events (TLEs), ELVES], the study of meteoroids, the search of interstellar meteoroids and strange quark matter, mapping of the Earth’s nocturnal emissions in the ultraviolet range, and the search of cosmic rays with energy above 10 $$^{21}$$ eV. The instrument has been integrated and qualified in 2019, with the final tests in Baikonur prior to its launch. Operations involve periodic installation in the Zvezda module of the station with observations during the crew night time, with periodic downlink of data samples, with the full data being sent to the ground via pouches containing the data disks. Mission planning involves the selection of the optimal orbits to maximize the scientific return of the instrument. In this work, we will describe the various phases of construction, testing, and qualification prior to the launch and the in-flight operations of the instrument on board the ISS.

A novel multi-anode MCP-PMT with Cherenkov radiator window

With the proposal of the road map of Time-of-Flight positron emission tomography (TOF-PET) with a Coincidence Time Resolution (CTR) of 10 ps by Paul Lecoq et al. in 2020, the technology based on TOF puts forward higher requirements on the performance of its core optical devices. In this manuscript, we developed a kind of Multi-Anode micro channel plate photomultiplier tube (MCP-PMT) based on Cherenkov radiator window. By using the Cherenkov radiator as the optical window of Multi-Anode MCP-PMT directly, the optical interface between the scintillator and the PMT window in conventional TOF-PET is eliminated, reducing light loss and further improve the time resolution of TOF-PET. The anode of this MCP-PMT can be split into a finely spaced array of collecting electrodes to achieve good positional sensitivity. In this paper, the single photon detection capability and time resolution of this kind of MCP-PMT are evaluated. The transit time spread (TTS) at single photon mode can reach 42.9 ps, and the TTS at multi photon mode is less than 10 ps. The CTR based on this kind of MCP-PMT is 156.7 ± 10.6 ps FWHM, which is equivalent to a position resolution of 23.5 ± 1.6 mm along a line of response (LOR). The performance uniformity of this kind MCP-PMT has also been calibrated.

Absolute calibration of the JEM-EUSO photodetection modules

The JEM-EUSO (Joint Experiment Missions for Extreme Universe Space Observatory) collaboration constructs a series of balloon and orbital telescopes to detect fluorescent UV emission from the Earth atmosphere, with the primary aim to study ultra-high-energy cosmic rays (UHECRs) from space. The detectors have wide field-of-view (more than 20 degrees FOV), high temporal resolution (1-2.5 µs) and high sensitivity provided by a large aperture. Currently, one of these detectors is operating onboard the International Space Station (Mini-EUSO). The next one is planned to be launched in the spring of 2023 (EUSO-SPB2) and another one is in preparation stage (K-EUSO). These projects use the same photo-detection modules (PDMs) composed of 36 multi-anode photomultiplier tubes (MAPMTs), each with 64 pixels, for a total of 2304 pixels. Mini-EUSO uses one PDM, EUSO-SPB2 uses three and the future full-scale missions will use several tens of PDMs. In the process of preparing and testing of PDMs, a new technique was developed to characterize their performance and provide absolute calibration of the MAPMTs used in the different JEM-EUSO missions. The method provides the efficiency of each pixel (including the sub-pixel structures), as well as the actual area occupied by the different pixels on the photocathode of the MAPMT. The method and its application to EUSO-SPB2 PDMs at different high voltages and in different modes of operation are presented.

An end-to-end in-flight calibration of Mini-EUSO detector

Mini-EUSO is a wide Field-of-View (FoV, 44°) telescope currently in operation from a nadir-facing UV-transparent window in the Russian Zvezda module on the International Space Station (ISS). It is the first detector of the JEM-EUSO program deployed on the ISS, launched in August 2019. The main goal of Mini-EUSO is to measure the UV emissions from the ground and atmosphere, using an orbital platform. Mini-EUSO is mainly sensitive in the 290–430 nm bandwidth. Light is focused by a system of two Fresnel lenses of 25 cm diameter each on the Photo-Detector-Module (PDM), which consists of an array of 36 Multi-Anode Photomultiplier Tubes (MAPMTs), arranged in blocks of 2 × 2 called Elementary Cells (ECs), for a total of 2304 pixels working in photon counting mode, in three different time resolutions of 2.5 µs (defined as 1 Gate Time Unit, GTU), 320 µs and 40.96 ms operating in parallel. In the longest time scale, the data is continuously acquired to monitor the UV emission of the Earth. It is best suited for the observation of ground sources and therefore has been used for the observational campaigns of the ground-based UV flasher in order to perform an end-to-end calibration of Mini-EUSO. In this contribution, the assembled UV flasher, the operation of the field campaign and the analysis of the obtained data are presented. The result is compared with the overall effi ciency computed from the expectations which takes into account the atmospheric attenuation and the parametrisation of different effects such as the optics effi ciency, the MAPMT detection effi ciency, BG3 filter transmittance and the transparency of the ISS window.

Implications of Mini-EUSO measurements for a space-based observation of UHECRs

Mini-EUSO is the first mission of the JEM-EUSO program on board the International Space Station. It was launched in 2019 and it is currently located in the Russian section (Zvezda module) of the station and viewing our planet from a nadir-facing UV-transparent window. The instrument is based on the concept of the original JEM-EUSO mission and consists of an optical system employing two Fresnel lenses and a focal surface composed of 36 Multi-Anode Photomultiplier tubes, 64 channels each, for a total of 2304 channels with single photon counting sensitivity and an overall field of view of 44° × 44°. Mini-EUSO can map the night-time Earth in the near UV range (predominantly between 290 nm and 430 nm), with a spatial resolution of about 6.3 km and different temporal resolutions of 2.5 µ, 320 µs and 41 ms. Mini-EUSO observations are extremely important to better assess the potential of a space-based detector in studying Ultra-High Energy Cosmic Rays (UHECRs) such as K-EUSO and POEMMA. In this contribution we focus the attention on UV measurements, the observation of clouds and of certain categories of events that Mini-EUSO triggers with the shortest temporal resolution. We place them in the context of UHECR observations from space, namely the estimation of exposure and sensitivity to Extensive Air Showers.