Monoclonal Antibody Aggregates Research Articles

Detection of IgG Aggregation by a High Throughput Method Based on Extrinsic Fluorescence

The utility of extrinsic fluorescence as a tool for high throughput detection of monoclonal antibody aggregates was explored. Several IgG molecules were thermally stressed and the high molecular weight species were fractionated using size-exclusion chromatography (SEC). The isolated aggregates and monomers were studied by following the fluorescence of an extrinsic probe, SYPRO Orange. The dye displayed high sensitivity to structurally altered, aggregated IgG structures compared to the native form, which resulted in very low fluorescence in the presence of the dye. An example of the application is presented here to demonstrate the properties of this detection method. The fluorescence assay was shown to correlate with the SEC method in quantifying IgG aggregates. The fluorescent probe method appears to have potential to detect protein particles that could not be analyzed by SEC. This method may become a powerful high throughput tool to detect IgG aggregates in pharmaceutical solutions and to study other protein properties involving aggregation. It can also be used to study the kinetics of antibody particle formation, and perhaps allow identification of the species, which are the early building blocks of protein particles.

The use of native cation‐exchange chromatography to study aggregation and phase separation of monoclonal antibodies

This study introduces a novel analytical approach for studying aggregation and phase separation of monoclonal antibodies (mAbs). The approach is based on using analytical scale cation-exchange chromatography (CEX) for measuring the loss of soluble monomer in the case of individual and mixed protein solutions. Native CEX outperforms traditional size-exclusion chromatography in separating complex protein mixtures, offering an easy way to assess mAb aggregation propensity. Different IgG1 and IgG2 molecules were tested individually and in mixtures consisting of up to four protein molecules. Antibody aggregation was induced by four different stress factors: high temperature, low pH, addition of fatty acids, and rigorous agitation. The extent of aggregation was determined from the amount of monomeric protein remaining in solution after stress. Consequently, it was possible to address the role of specific mAb regions in antibody aggregation by co-incubating Fab and Fc fragments with their respective full-length molecules. Our results revealed that the relative contribution of Fab and Fc regions in mAb aggregation is strongly dependent on pH and the stress factor applied. In addition, the CEX-based approach was used to study reversible protein precipitation due to phase separation, which demonstrated its use for a broader range of protein-protein association phenomena. In all cases, the role of Fab and Fc was clearly dissected, providing important information for engineering more stable mAb-based therapeutics.

Influence of pH on Heat-Induced Aggregation and Degradation of Therapeutic Monoclonal Antibodies

Monoclonal antibodies are widely used for the treatment of various diseases, and because therapeutic monoclonal antibodies are stored in an aqueous solution or in a lyophilized state, the preparation of a stabilizing formulation that prevents their deterioration (degradation and aggregation) is crucial. Given the structural similarities of the immunoglobulin G (IgG) framework regions and a diversity of only four subclasses, we aimed to find common conditions that stabilize many different antibodies. In this study, we analyzed the effect of pH (the most critical factor in establishing a stable formulation) on human monoclonal antibodies from subclasses IgG1, IgG2, and IgG4, all of which have been utilized in antibody therapeutics. We found that human IgGs are stable with minimal heat-induced degradation and aggregation at pH 5.0-5.5 irrespective of their subclass. We also found that IgG1 is more susceptible to fragmentation, whereas IgG4 is more susceptible to aggregation. This basic information emphasizing the influence of pH on IgG stability should facilitate the optimization of formulation conditions tailored to individual antibodies for specific uses.

Impact of freezing on pH of buffered solutions and consequences for monoclonal antibody aggregation

Freezing of biologic drug substance at large scale is an important unit operation that enables manufacturing flexibility and increased use-period for the material. Stability of the biologic in frozen solutions is associated with a number of issues including potentially destabilizing pH changes. The pH changes arise from temperature-associated change in the pK(a)s, solubility limitations, eutectic crystallization, and cryoconcentration. The pH changes for most of the common protein formulation buffers in the frozen state have not been systematically measured. Sodium phosphate buffer, a well-studied system, shows the greatest change in pH when going from +25 to -30 degrees C. Among the other buffers, histidine hydrochloride, sodium acetate, histidine acetate, citrate, and succinate, less than 1 pH unit change (increase) was observed over the temperature range from +25 to -30 degrees C, whereas Tris-hydrochloride had an approximately 1.2 pH unit increase. In general, a steady increase in pH was observed for all these buffers once cooled below 0 degrees C. A formulated IgG2 monoclonal antibody in histidine buffer with added trehalose showed the same pH behavior as the buffer itself. This antibody in various formulations was subject to freeze/thaw cycling representing a wide process (phase transition) time range, reflective of practical situations. Measurement of soluble aggregates after repeated freeze-thaw cycles shows that the change in pH was not a factor for aggregate formation in this case, which instead is governed by the presence or absence of noncrystallizing cryoprotective excipients. In the absence of a cryoprotectant, longer phase transition times lead to higher aggregation.

Effects of Arginine on Photostability and Thermal Stability of IgG1 Monoclonal Antibodies

This study demonstrates that arginine is a highly effective solvent additive which significantly reduces the light induced aggregation of four IgG1 type monoclonal antibodies (named as IMC-1A, IMC-1B, IMC-1C and IMC-1D) as measured by size exclusion chromatography. All experiments were performed in a phosphate buffer system containing either sodium chloride or arginine hydrochloride. The protein samples were exposed to light in a photo chamber according to ICH (International Conference on Harmonization) guidelines. Thermal unfolding transition temperature (T(m)) of IMC-1A as determined by differential scanning calorimetry (DSC) was significantly decreased ( approximately 3.3 degrees C) in the presence of arginine hydrochloride as compared to in sodium chloride. However, a noticeable increase in thermal stability was observed for IMC-1B, IMC-1C and IMC-1D in the presence of arginine hydrochloride. The photostability of all these molecules was significantly enhanced by arginine hydrochloride and both a direct and inverse correlation was observed between conformational stability and photostability. To our knowledge, this paper for the first time, demonstrates that arginine hydrochloride considerably reduces the light induced aggregation of monoclonal antibodies. Arginine hydrochloride is also known to increase protein solubility and its ability to extensively reduce light induced aggregation makes it a potential solvent additive for the formulation development of therapeutic proteins.

Structural properties of monoclonal antibody aggregates induced by freeze–thawing and thermal stress

Aggregation of monoclonal antibodies can be induced by freeze–thawing and elevated temperature, typical stress factors during development, production and storage. Our aim was to characterize structural properties of aggregates formed after freeze–thawing and thermal stressing of humanized monoclonal IgG 1 antibody (IgG). Formulations with 1.0 mg/ml IgG in 100 mM phosphate pH 7.2 were subjected to freeze–thawing and heating and characterized by spectroscopic techniques (UV-absorption, CD, ATR-FTIR and fluorescence), light obscuration, dynamic light scattering, SDS-PAGE, AF4 with UV and MALLS detection, and HP-SEC with UV and online fluorescent dye detection. Thermal stress led to an increased formation of dimers and soluble oligomers (HP-SEC, AF4). Aggregates smaller than 30 nm were measured (DLS), next to slightly elevated particle levels in the μm range (light obscuration). Aggregates created by heating were in part covalently linked (SDS-PAGE) and made up of conformationally perturbed monomers (CD, ATR-FTIR, extrinsic dye fluorescence). Aggregation after freeze–thawing was manifested primarily in particle formation in the μm range. These aggregates were noncovalently linked (SDS-PAGE) and composed of native-like monomers, as obvious from CD, ATR-FTIR and extrinsic dye fluorescence spectroscopy. In conclusion, the complementary methods used in this study revealed that heating and freeze–thawing induced aggregates differ significantly in their physico-chemical characteristics.

Application of Vibrational Spectroscopy to the Structural Characterization of Monoclonal Antibody and its Aggregate

Aggregation is often the major issue during formulation and manufacturing development of therapeutic proteins, in particular human monoclonal antibody. Currently, there is a lack of structural information of aggregates of such large protein as human antibodies, due to the large molecular sizes of the aggregates. In this article, we shall discuss the application of vibrational spectroscopies including FT-IR, Raman and Raman Optical Activity (ROA), to characterize the structures of various types of monoclonal antibody aggregates formed under different stresses. Two different classes of human monoclonal antibodies, namely IgG1 and IgG2, have been subjected to this structural investigation. The common stresses leading to antibody aggregation, mis-folding or unfolding during manufacturing and formulation include exposure to acidic pHs, heat and shear stress. The effect of different types of stresses on the structure and aggregate formation of human monoclonal antibodies has been investigated by employing vibrational spectroscopy. While data present only monoclonal antibody, the same technology can be used for any protein aggregates.

Effects of Solution Conditions, Processing Parameters, and Container Materials on Aggregation of a Monoclonal Antibody during Freeze-Thawing

Freeze-thawing is a potentially damaging stress to which therapeutic proteins can be exposed deliberately during storage of bulk drug substance, and accidentally because of mishandling of commercial product during shipping and/or storage. The primary route of degradation induced by freeze-thawing is protein aggregation. We studied the effects of freeze-thawing on aggregation of an IgG2 monoclonal antibody, examining solution conditions (pH, and the presence or absence of 150 mM KCl), protein concentration, cooling and warming rates, and container type and material. In addition, we determined the effect of pH and KCl on protein tertiary structure and thermal stability with second derivative UV spectroscopy. In general, aggregation of the antibody during freeze-thawing increased with decreasing pH, which correlated well with Tm values. Aggregation was most prevalent at pH 3 and 4, with potential mechanisms involving both the formation of aggregation-prone conformational states as well as adsorption to and denaturation at various interfaces. Although all the parameters examined demonstrated some effect on the formation of soluble aggregates, the effect of container material was especially pronounced. Samples stressed in plastic or glass containers contained low amounts of aggregate. Storage in Teflon or commercial freezing containers, however, led to significantly higher levels of aggregate formation.

Fractionation of monoclonal antibody aggregates using membrane chromatography

Monoclonal antibodies (mAbs) comprise an important class of biopharmaceuticals. Aggregation of mAbs is a common though undesirable occurrence. Size exclusion chromatography (SEC) which is used for both analysis and preparative separation of mAb aggregates is slow and results in poorly resolved peaks, particularly for higher order aggregates. We describe a hydrophobic interaction membrane chromatography (HIMC) based method for rapid and efficient separation and analysis of mAb aggregates. Our method was able to resolve Campath-1H monomer, dimer, trimer, tetramer and pentamer. The results obtained also strongly supported our hypothesis that the hydrophobicity of mAb increases with the degree of aggregation, i.e. a dimer is more hydrophobic than a monomer, a trimer more than a dimer, and so on.

Effects of acid exposure on the conformation, stability, and aggregation of monoclonal antibodies

Exposure of antibodies to low pH is often unavoidable for purification and viral clearance. The conformation and stability of two humanized monoclonal antibodies (hIgG4-A and -B) directed against different antigens and a mouse monoclonal antibody (mIgG1) in 0.1M citrate at acidic pH were studied using circular dichroism (CD), differential scanning calorimetry (DSC), and sedimentation velocity. Near- and far-UV CD spectra showed that exposure of these antibodies to pH 2.7-3.9 induced only limited conformational changes, although the changes were greater at the lower pH. However, the acid conformation is far from unfolded or so-called molten globule structure. Incubation of hIgG4-A at pH 2.7 and 3.5 at 4 degrees C over the course of 24 h caused little change in the near-UV CD spectra, indicating that the acid conformation is stable. Sedimentation velocity showed that the hIgG4-A is largely monomeric at pH 2.7 and 3.5 as well as at pH 6.0. No time-dependent changes in sedimentation profile occurred upon incubation at these low pHs, consistent with the conformational stability observed by CD. The sedimentation coefficient of the monomer at pH 2.7 or 3.5 again suggested that no gross conformational changes occur at these pHs. DSC analysis of the antibodies showed thermal unfolding at pH 2.7-3.9 as well as at pH 6.0, but with decreased melting temperatures at the lower pH. These results are consistent with the view that the antibodies undergo limited conformational change, and that incubation at 4 degrees C at low pH results in no time-dependent conformational changes. Titration of hIgG4-A from pH 3.5 to 6.0 resulted in recovery of native monomeric proteins whose CD and DSC profiles resembled those of the original sample. However, titration from pH 2.7 resulted in lower recovery of monomeric antibody, indicating that the greater conformational changes observed at this pH cannot be fully reversed to the native structure by a simple pH titration.

Non-Size-Based Membrane Chromatographic Separation and Analysis of Monoclonal Antibody Aggregates

Humanized monoclonal antibody produced by mammalian cell culture may contain significant amounts of antibody dimers and smaller amounts of higher order aggregates. These are undesirable in therapeutic formulations, and their content should be lower than specific allowable limits. Quantitative analysis of aggregate content is usually carried out by size exclusion chromatography (SEC), which is slow and often gives poorly resolved peaks. We describe a novel hydrophobic interaction membrane chromatography-based technique for rapid, non-size-based separation and analysis of the aggregate content in monoclonal antibody samples. The typical sample analysis time using this technique is less than 3 min, this being significantly faster than SEC. The technique gives excellent resolution of the antibody, its dimer, and higher order aggregates and could potentially be scaled up for large-scale manufacture of aggregate-free monoclonal antibody. This work also clearly shows that monoclonal antibody aggregates are more hydrophobic than the monomer form, a fact that could have significant theoretical and practical implications.

Influence of osmolarity and pH increase to achieve a reduction of monoclonal antibodies aggregates in a production process.

Anti PSA monoclonal antibodies for diagnostic use were produced in an in vitro system. After purification using Protein G affinity chromatography a percentage of about 10% of antibody aggregates remained. The use of monoclonal antibodies containing aggregates as a capture antibody in a diagnostic kit reduces the performance of the test making it often unacceptable. The aggregates could be eliminated using gel filtration chromatography but, in that way, the final recovery of the whole production process was only about 50%. Aggregation is favoured when the working pH is near to the isoelectric point of the antibody. We varied the culture medium composition, modifying pH and osmolarity. We tested different values of pH and osmolarity: 7.1, 7.5, 8.0, 8.5 for pH, and 300, 340, 367, 395 mOsm/kg H2O for osmolarity. By modification of the cell culture medium we obtained a significant decrease of monoclonal antibody aggregates in the production cycle. In this way we achieved higher recovery rate and could avoid gel filtration polishing step. The experiments were performed in two stages: first in culture flasks changing one parameter in each experiment, and then in spinner bottle using the best conditions obtained in the first stage. During scale up we used the modifications achieved from the experiment showed in this paper in our production by hollow fibre bioreactor with positive results.

Separation and Quantitation of Monoclonal Antibody Aggregates by Asymmetrical Flow Field-Flow Fractionation and Comparison to Gel Permeation Chromatography

During the downstream processing of monoclonal antibodies (Mab) the formation of dimers and/or oligomers may occur. Today, the most common technique for determination of aggregate content is gel permeation chromatography (GPC) but it has limited resolution and separation speed. Oligomers are particularly difficult to resolve. Asymmetrical flow field-flow fractionation (FFF) is a new analytical method for the separation of Mab aggregates. The monomer and dimer peaks were well resolved and three additional peaks, thought to be trimers, tetramers, and pentamers were partially resolved. The total time for a separation can be kept as short as 6 min. The GPC separation takes about 15 min with less resolution. A study of the reproducibility for the two techniques revealed that the precision was slightly better for GPC. Investigation of the dependence of sample concentration showed that the load limit for FFF was about 4 μg of Mab. The GPC technique requires prefiltered samples in order to avoid clogging of the column. For FFF it is possible to inject samples containing precipitated material without any pretreatment. The flow conditions can be adjusted so that the precipitated material elutes with the front, well separated from the monomer peak.

The effect of pH on the aggregation of biotinylated antibodies and on the signal-to-noise observed in immunoassays utilizing biotinylated antibodies

During the development of immunoassays to detect gram-negative bacteria, an effect of pH on the aggregation of some murine monoclonal antibodies directed to Neisseria gonorrhoeae was observed. By reacting positively charged primary amines on these antibodies with the neutral NHS-biotin ( N-hydroxy-succinimidobiotin), the surface charge on the antibodies was altered and a concomitant change in the solubility of these antibodies noted. This derivatization produced not only a pH-dependent change in the solubility properties of the antibodies, but also affected the response of immunoassays in which these antibodies were used. Data presented suggests that the signal-to-noise (S/N) observed in these assays is maximized under conditions where the biotinylated antibody is introduced into the assay at a pH at least 2 U above its p I. Our hypothesis is that as the pH of the solution approaches the biotinylated antibodies' isoelectric point, they become ‘stickier’, perhaps by aggregation (which we have directly measured), leading to high non-specific binding and hence a lower S/N.

Announcement

Previous article No AccessAnnouncementPDFPDF PLUS Add to favoritesDownload CitationTrack CitationsPermissionsReprints Share onFacebookTwitterLinkedInRedditEmail SectionsMoreDetailsFiguresReferencesCited by The Journal of Modern History Volume 22, Number 1Mar., 1950 Article DOIhttps://doi.org/10.1086/237328 Citations: 2Citations are reported from Crossref Copyright 1950 The University of Chicago PressPDF download Crossref reports the following articles citing this article:James D. Andya, Jun Liu, Steven J. Shire Analysis of Irreversible Aggregation, Reversible Self-association and Fragmentation of Monoclonal Antibodies by Analytical Ultracentrifugation, (Oct 2009): 207–227.https://doi.org/10.1007/978-0-387-76643-0_13Gerald L. Carlson, Gene M. Brown The Natural Occurrence, Enzymatic Formation, and Biochemical Significance of a Hydroxyethyl Derivative of Thiamine Pyrophosphate, Journal of Biological Chemistry 236, no.77 (Jul 1961): 2099–2108.https://doi.org/10.1016/S0021-9258(18)64136-5