MnO2 Research Articles

Light-weight flexible symmetric supercapacitors based on magnesium-zinc codoped MnO2 nanostructures on carbon cloth as enhanced-performance binder-free electrodes

Developing advanced flexible supercapacitors with high energy and power density is a critical research goal. One promising approach involves combining manganese dioxide (MnO2) with a three-dimensional carbon substrate. This strategy leads to the creation of supercapacitor electrode materials that exhibit high specific capacitance, stability, and environmental friendliness. However, the challenge lies in addressing the low electrical conductivity of MnO2, which limits the rate of electron transfer. The incorporation of metal ions enhances the conductivity of manganese oxide, resulting in a significant increase in lattice defects. These defects create abundant active sites for energy storage. In this study, we developed flexible electrodes based on magnesium-doped MnO2, zinc-doped MnO2, and magnesium-zinc codoped MnO2 nanostructures deposited on carbon cloth (CC) via a one-step hydrothermal method. The supercapacitive behavior of these electrodes was investigated using CV and GCD measurements. The as-prepared electrodes exhibit good electrical conductivity, and their interconnected network structure, composed of sponge-shaped nanostructure layers, results in a large specific surface area. This network also facilitates efficient pathways for effective electron transport. The optimized Mg-Zn codoped MnO2@CC sample exhibits a high capacitance of 79.9 mF/cm² at 0.7 mA/cm² and good rate performance, reaching around 46.59 mF/cm² up to 1.5 mA/cm² in the three-electrode system. Notably, the areal capacitance values calculated from the CV curves for all Mg-Zn codoped MnO2@CC electrodes surpass those of Mg-doped MnO2@CC and Zn-doped MnO2@CC. A flexible symmetric supercapacitor assembled using the best Mg-Zn codoped MnO2@CC as both positive and negative electrodes and PVA-Na2SO4 gel electrolyte delivers a desirable energy density of 0.196 mWh/cm2 at 2.38 mW/cm2. Furthermore, this fabricated supercapacitor demonstrates a broad voltage window of 2.25 V and remarkable cycling stability, retaining 83 % of its initial performance after 4000 charge-discharge cycles.

Additional research into arsenic (III) effective catalytic oxidation in an aqueous solution on a new calcium doped active manganese dioxide in a flow column

Additional research into arsenic (III) effective catalytic oxidation in an aqueous solution on a new calcium doped active manganese dioxide in a flow column

Preinserted Ammonium in MnO2 to Enhance Charge Storage in Dimethyl Sulfoxide Based Zinc-Ion Batteries.

Nonaqueous zinc-ion batteries (NZIBs) featuring manganese dioxide (MnO2) cathodes position themselves as viable options for large-scale energy storage systems. Herein, we demonstrate the use of ammonium cation as a preintercalant to improve the performance of the δ-MnO2 cathode in wet dimethyl sulfoxide based electrolytes. Employing in situ X-ray absorption spectroscopy, Raman spectroscopy, and synchrotron X-ray diffraction, we reveal that the integration of ammonium cations promotes the formation of NH-O-Mn networks. These networks are crucial for manipulating the distortion of the MnO6 octahedral units during discharging, thereby mitigating charge disproportionation, which is a primary limitation to MnO2's charge-storage efficiency. The modified MnO2, through this idea, displays a notable improvement in capacity (∼247 mAh/g) and can pass charge-discharge cycles up to 500 cycles with a capacity retention of 85%. These findings underscore the potential of modified MnO2 in advancing MnO2-based hosts for Zn-MnO2 batteries, marking significant progress toward next-generation energy storage solutions.

Synthesis of Porous Carbon Honeycomb Structures Derived from Hemp for Hybrid Supercapacitors with Improved Electrochemistry.

Energy storage in electrochemical hybrid capacitors involves fast faradaic reactions such as an intercalation, or redox process occurring at a solid electrode surface at an appropriate potential. Hybrid sodium-ion electrochemical capacitors bring the advantages of both the high specific power of capacitors and the high specific energy of batteries, where activated carbon serves as a critical electrode material. Herein, we have demonstrated that a porous honeycomb structure activated carbon derived from Australian hemp hurd (Cannabis sativa L.) in aqueous Na2SO4 electrolyte showed a specific capacitance of 240 F/g at 1 A/g.The hybrid sodium-ion device employing hemp-derived activated carbon (HAC) coupled with electrolytic manganese dioxide (EMD) in an aqueous Na2SO4 electrolyte showed a specific capacitance of 95 F/g at 1 A/g having a capacitance retention of 90%. The hybrid device (HAC||EMD) can possess excellent electrochemical performance metrics, having a high energy density of 38 Wh/kg at a power density of 761 W/kg. Overall, this study provides insights into the influence of the activation temperature and the KOH impregnation ratio on morphology, porosity distribution, and the activated carbon's electrochemical properties with faster kinetics. The high cell voltage for the device is devoted to the EMD electrode.

Investigation the Influence of Calcination Temperature on Structural, Electrical and Gas Sensing Properties MnO<sub>2</sub> Thick Films

Metal oxide nanoparticles are widely used in various fields, including catalysis, sensing, energy storage, and more. Manganese dioxide (MnO2) is a promising material for gas sensors due to its sensitivity to various gases, including oxidizing and reducing gases. The calcination temperature affects their size, crystallinity, surface area, and other properties. In the present research work, the influence of calcination temperature on the structural, electrical and gas sensing properties of MnO2 nanoparticles or nanopowders was investigated. The MnO2 nanopowder was calcinated at 200, 400, 600, and 800 °C in a muffle furnace for 4 hours. After that, using the calcinated powder of MnO2, the thick films were prepared using the standard screen printing technique. The structural characterizations were investigated using SEM, EDS, and XRD. It has been found that as the calcination temperature is increased, the electrical, structural, and gas-sensing properties of MnO2 change. The prepared thick films calcinated at 200, 400, 600, and 800 °C are labeled as samples 1, 2, 3, and 4, respectively, in this paper. It has been found that sample 4 shows maximum resistivity, a more specific surface area, a smaller crystallite, and a maximum gas response to H2S gas. The maximum sensitivity was found to be 76.32% to H2S gas at operating temperature 120 °C. The response and recovery time was also found quickly.

A Novel Nanocatalyst for Combined Chemodynamic and Starvation Therapy in Cancer Treatment

Cancer remains a significant challenge due to the limitations and side effects of tra- ditional treatments. Novel minimally invasive therapies are essential to enhance patient outcomes. This study introduces MIL-101(Fe)@MnO2 @Gox/HA, a nanocatalyst that com- bines glucose oxidase and manganese dioxide in an iron-based metal-organic framework (MOF) coated with hyaluronic acid. This nanoplatform demonstrates strong water affin- ity, tumor targeting, and durability. MIL-101(Fe)@MnO2 @Gox/HA presents a promis- ing anti-cancer strategy, warranting further investigation to enhance tumor targeting and treatment efficacy.

Targeted nanoprobe for magnetic resonance imaging-guided enhanced antitumor via synergetic photothermal/immunotherapy

Synergistic photothermal/immunotherapy has garnered significant attention for its potential to enhance tumor therapeutic outcomes. However, the fabrication of an intelligent system with a simple composition that simultaneously exerts photothermal/immunotherapy effect and imaging guidance function still remains a challenge. Herein, a glutathione (GSH)-responsive theranostic nanoprobe, named HA-MnO2/ICG, was elaborately constructed by loading photothermal agent (PTA) indocyanine green (ICG) onto the surface of hyaluronic acid (HA)-modified manganese dioxide nanosheets (HA-MnO2) for magnetic resonance (MR) imaging-guided synergetic photothermal/immuno-enhanced therapy. In this strategy, HA-MnO2 nanosheets were triggered by the endogenous GSH in tumor microenvironment to generate Mn2+ for MR imaging, where the longitudinal relaxation rate of HA-MnO2/ICG was up to 14.97 mM−1s−1 (∼24 times than that found in a natural environment), demonstrating excellent intratumoral MR imaging. Moreover, the HA-MnO2/ICG nanoprobe demonstrates remarkable photothermal therapy (PTT) efficacy, generating sufficient heat to induce immunogenic cell death (ICD) within tumor cells. Meanwhile the released Mn2+ ions from the nanosheets function as potent immune adjuvants, amplifying the immune response against cancer. In vivo experiments validated that HA-MnO2/ICG-mediated PTT was highly effective in eradicating primary tumors, while simultaneously enhancing immunogenicity to prevent the growth of distal metastasis. This hybrid HA-MnO2/ICG nanoprobe opened new avenues in the design of MR imaging-monitored PTT/immuno-enhanced synergistic therapy for advanced cancer.

Humic acid changes effect of naturally occurring oxidants on the environmental transformation of molybdenum disulfide nanosheets

2H-phase molybdenum disulfide (2H-MoS2) has been considered to be a chemically stable two-dimensional (2D) nanomaterial. Nonetheless, the persistence of 2H-MoS2 in the presence of environmental redox-active matrices, such as naturally occurring oxidants (e.g., manganese dioxide (MnO2)) and natural organic matter (NOM), remains largely unknown. Herein, we examined the interplay between 2H-MoS2, MnO2 (a common natural oxidant), and NOM species (i.e., Aldrich humic acid (ALHA) and Suwannee River natural organic matter (SRNOM)). The results show that MnO2 accelerates the oxidative dissolution of 2H-MoS2, regardless of the presence of dissolved oxygen. The effect of NOM on the MnO2-induced fate of 2H-MoS2 was found to depend on its affinity for 2H-MoS2 and the functionality of NOM. ALHA preferentially adsorbed on hydrophobic 2H-MoS2 nanosheets due to the enrichment of reductive polycyclic aromatics and polyphenolic constituents. The preferential ALHA adsorption counteracted the MnO2-triggered oxidative transformation of 2H-MoS2, as revealed by the cathodic response of 2H-MoS2 (i.e., decreased the open circuit potential by 0.0338 V) and the emergence of reductive Mo‒C bonds at 228.8 and 231.9 eV upon the addition of ALHA. This work evaluated the persistence of 2H-MoS2, illustrating its susceptibility to decomposition by naturally occurring oxidants and the influence of NOM on it. These findings are crucial for revealing the fate and transport of MoS2 in aquatic environments and provide guidelines for related applications in natural or engineered systems for MoS2 and potentially other 2D materials.

Effects of B2O3 Dopants on the Electrical Properties of Ta‐Doped SnO2 Varistors

As a new core component of surge arresters, it is crucial for manganese dioxide varistors to solve the challenges of reducing the leakage current and lowering the residual voltage ratio. In this study, the electrical characteristics of tin dioxide varistors using B2O3 as the acceptor dopant and Ta2O5 as the donor dopant are investigated. Several tin dioxide based varistors doped with different amounts of B2O3 are prepared and characterized by the researchers. X ray diffraction (XRD) is used to analyze the structural features of the samples and to observe the phases involved. It is found that the B2O3 dopant provides oxygen vacancies, reduces the grain size, increases the barrier height, and decreases the residual pressure ratio. The Ta2O5 dopant provides donor defects and free electrons needed to form the barrier. When balancing the concentrations of B2O3 and Ta2O5, the optimum dopant concentrations is found to be 0.1 mol% of B and 0.05 mol% of Ta; these concentrations result in a leakage current of 0.25 μA cm−2, a residual pressure ratio of 1.95, a nonlinear coefficient of 25, and a voltage gradient of 394 V mm−1 for the varistor.

Manganese dioxide as wide adaptive ultrafast photonic device for pulsed laser generation

Manganese dioxide as wide adaptive ultrafast photonic device for pulsed laser generation

Unveiling the synergistic interaction: Investigating the enhanced mechanism of 4H–SiC chemical mechanical polishing with the addition of sodium silicate and manganese dioxide

Silicon carbide (SiC), the quintessential semiconductor material, poses an acute challenge to the realization of highly efficient ultra-precision processing. This study has investigated the effect of the combined ratio of sodium silicate and manganese dioxide on the polishing rate and surface roughness of 4H–SiC in chemical mechanical polishing (CMP). The synergistic mechanism of sodium silicate and manganese dioxide on slurry spreading performance and particle dispersion stability is characterized by surface wettability, surface tension, scanning electron microscopy, zeta potential analysis and X-ray photoelectron spectroscopic. Based on the above studies, the synergistic mechanism of sodium silicate and manganese dioxide on the CMP of 4H–SiC is attributed to the improvement of the suspension stability of the abrasive as well as the oxidizing ability of the slurry.

Exploration of TiMn/Ti anode for optimizing the structure and performance of electrolytic manganese dioxide

With the deepening application of manganese based cathode materials in new energy vehicle power batteries and wind solar energy storage batteries, diversified application scenarios also demand higher and more diverse performance of manganese based cathodes. This work adopts a new type of TiMn/Ti anode to replace traditional Ti anode preparing electrolytic manganese dioxide (EMD), to meet the requirements of manganese based batteries. Results show that the electrolysis process based on TiMn/Ti anode successfully achieves controllable adjustment of EMD structure by changing process parameters. Besides, the relationship between EMD structure and battery performance was studied. Meanwhile, density functional theory (DFT) calculation reveals that the existence of Mn (III) in EMD is the key to prepare a optimized non-stoichiometry Li1+yMn2-yO4. This work improves the performance of the cathodes of manganese based batteries by optimizing the quality of raw materials, providing a new perspective for the development of high-quality manganese based batteries.

Phase–activity relationship of MnO2 nanomaterials in periodate oxidation for organic pollutant degradation

Manganese dioxide (MnO2), renowned for its abundant natural crystal phases, emerges as a leading catalyst candidate for the degradation of pollutants. The relationship between its crystal phase and catalytic activity, particularly for periodate activation, has remained both ambiguous and contentious. This study delineates the influence of various synthetic MnO2 phase structures on their capabilities in catalyzing periodate-assisted pollutant oxidation. Five distinct MnO2 phase structures (α-, β-, γ-, δ-, and ε-MnO₂) were prepared and evaluated to activate periodate and degrade pollutants, following the sequence: α-MnO₂ > γ-MnO₂ > β-MnO₂ > ε-MnO₂ > δ-MnO₂. Through quenching experiments, electron paramagnetic resonance tests, and in situ electrochemical studies, we found an electron transfer-mediated process drive pollutant degradation, facilitated by a highly reactive metastable intermediate complex (MnO₂/PI*). Quantitative structure-activity relationship analysis further indicated that degradation efficiency is strongly associated with both the crystal phase and the Mn (IV) content, highlighting it as a key active site. Moreover, the α-MnO₂ phase demonstrated exceptional recycling stability, enabling an effective pollutant removal in a continuous flow packed-bed reactor for 168 h. Thus, α-MnO₂/PI proved highly effective in mineralizing organic pollutants and reducing their toxicities, highlighting its significant potential for environmental remediation.

A multifunctional mesoporous silica drug delivery nanosystem that ameliorates tumor hypoxia and increases radiotherapy efficacy

Radiotherapy (RT) is a widely used treatment with strong therapeutic effects, but overcoming challenges related to hypoxia-induced tumor resistance and ineffective antitumor immune responses is crucial for optimal outcomes. In this study, we developed a versatile nanosystem using mesoporous silica nanoparticles (MSNs), R837, and a small quantity of manganese peroxide (Mn/ZnO2). The synthesized MSN@R837-Mn/ZnO2 nanoparticles exhibited precise tumor targeting and accumulation, controlled drug release under acidic conditions, and increased sensitivity in magnetic resonance imaging. These attributes collectively augmented the therapeutic efficacy of RT by alleviating hypoxia and immunosuppression. Tumor cells treated with RT combined with these nanoparticles displayed reduced oxidative stress, alleviated hypoxia, and normalized blood vessel formation. Notably, all mice in the RT + PD-1 + MSN@R837-Mn/ZnO2 group achieved complete tumor regression with extended survival. Safety assessments confirmed the absence of MSN@R837-Mn/ZnO2 toxicity, highlighting its potential as a promising approach with dual functionality for the diagnostic imaging and treatment of cancer.

Controllable synthesis of amidoximated self-propelled tubular micromotors for enhanced uranium recovery: non-invasive mixing and on-the-move capturing

Micro-/nanomotors that combine attributes of autonomous movement and adsorption performance are attractive for efficient pollutant treatment. However, micro/nanomotors design still suffers from challenges including complex manufacturing processes, specific instrument demands and low yields. Herein, we proposed amidoxime-functionalized polydopamine tubular micromotors (DNBMs-AO) and demonstrated their application for rapid selective adsorption of uranium from contaminated seawater. The whole fabrication procedure is simplified and straightforward by curcumin templating and in-situ reduction/graft method. The manganese dioxide (MnO2) catalyst and amidoxime groups are subsequently anchored on the outer and inner side of nanotube surface. Besides, the distribution and amount of modified MnO2 and amidoxime groups can be manipulated via directly changing the reduction time. DNBMs-AO are driven and propelled by microbubbles produced by MnO2-triggered catalytic decomposition of hydrogen peroxide, which can reach high velocity at 302.6 μm s−1. The static adsorption results indicate that the adsorption of U(VI) onto DNBMs-AO can be better described by Langmuir model with the maximum adsorption capacity of 313.9 mg/g. Moreover, the motion of DNBMs-AO can efficiently improve the U(VI) diffusion under low H2O2 concentration, and enhance the adsorption kinetics to approximately 2.5 times. DNBMs-AO also exhibits high selectivity towards U(VI) and excellent performance stability, endowing its potential application in environmental engineering field.

3D-printed multifunctional biomass hydrogel device for controlled photothermal distribution and molecular release

Photothermal therapy based on photothermal conversion has received increasing attention due to its non-invasiveness and low side effects. In this study, a 3D-printed biomass photothermal therapy device was prepared for accurate control of photothermal conversion and molecular release. The prepared black phosphorus nanosheets (BPNSs) showed excellent photothermal performance and antibacterial activity. A temperature-regulated sol-gel reversible system was prepared with konjac glucomannan (KGM), tara gum (TG), BPNSs, and manganese dioxide (MnO2) nanoparticles. The sol-gel transition was attributed to the change of interactions of hydrogen bond, and molecular entanglement. Photothermal conversion films with accurate multi-layer and array structures were prepared by 3D printing using the biomass sol-gel conversion system. The photothermal conversion efficiency was regulated by the concentration of BPNSs and MnO2. Under infrared radiation (808 nm, 1 W/cm2) for 5 min, the temperatures of hydrogel films with a MnO2 concentration of 0, 0.5, and 1 % were raised from 25 to 29.3, 61.8, and 90.8 °C, respectively. The accurate temperature distribution induced the controlled release of small active molecules such as epigallocatechin gallate (EGCG) loaded in hydrogels, which was resulted from the changes in the hydrogel structure and the decrease in adsorption energy between polysaccharide and EGCG at high temperatures. This study provides a biomass 3D-printed multifunctional photothermal therapy device and more understanding of the molecular release during photothermal conversion.

The Bioactive Interface of Titanium Implant with Both Anti-Oxidative Stress and Immunomodulatory Properties for Enhancing Osseointegration under Diabetic Condition.

The poor implant-osseointegration under diabetic condition remains a challenge to be addressed urgently. Studies have confirmed that the diabetic pathological microenvironment is accompanied by excessive oxidative stress, imbalanced immune homeostasis, and persistent chronic inflammation, which seriously impairs the osteogenic process. Herein, a multifunctional bioactive interface with both anti-oxidative stress and immunomodulatory properties is constructed on titanium implants. Briefly, manganese dioxide nanosheets are coated onto mesoporous polydopamine nanoparticles loaded with carbon monoxide gas precursor, namely MnO2-CO@MPDA NPs, and then they are integrated on the titanium implant to obtain MCM-Ti. In the simulated diabetic microenvironment, under the action of MnO2 nanoenzymes, MCM-Ti can effectively eliminate intracellular reactive oxygen species while alleviating hypoxic state. Interestingly, the microenvironment mediates the responsive release of CO gas, which effectively drives macrophages toward M2 polarization, thereby ameliorating inflammatory response. The potential mechanism is that CO gas up-regulates the expression of heme oxygenase-1, further activating the Notch/Hes1/Stat3 signaling pathway. Furthermore, the conditioned medium derived from macrophages on MCM-Ti surface significantly enhances the osteogenic differentiation of BMSCs. In a type 2 diabetic rat model, MCM-Ti implant effectively alleviates the accompanying inflammation and enhances the osseointegration through the synergistic effects of resisting oxidative stress and remodeling immune homeostasis.

Heterojunction photocatalyst MnO2-CsSnI3 for highly efficient formaldehyde oxidation at room temperature

The effective removal of the low-concentration formaldehyde (HCHO) in the indoor environment is a critical issue affecting the quality of people’s daily lives. In this study, heterojunction catalysts composed of manganese dioxide (MnO2) and cesium tin iodine (CsSnI3) nanocrystals were first synthesized and successfully used for photocatalytic HCHO degradation. After the full band light irradiation (150 mW/cm2) for 3 h, the concentration of HCHO decreased from 7 ppm to a minimum of 0.03 ppm at room temperature (25 °C, 25 % RH, degradation efficiency reaches up to 99.6 %). Subsequent analysis using electron paramagnetic resonance (EPR) and transmission electron microscopy (TEM) revealed that the MnO2-CsSnI3 heterojunction photocatalyst not only offers a Z-scheme charge-transfer pathway but also promotes the generation of a large number of •O2− and •OH. Compared to the single-phase material, the concentration of •O2− and •OH has increased by 1.5 times. This MnO2-based Z-scheme heterojunction photocatalyst provides a novel strategy for the degradation of low-concentration HCHO in practical indoor environments.

Stable Cycling of Ultrahigh Mass Loaded MnO2 for Low-Cost Sodium-Ion Batteries

Achieving cost-effective and sustainable solutions for large-scale energy storage is critical for advancing the global clean energy transition. The intermittent nature of green energy underscores the inadequacy of current large scale energy storage technologies like pumped hydroelectricity which is susceptible to geographic and water resource constraints, making batteries a prime candidate for this role. Although lithium-ion batteries (LIBs) with high energy and power density are a viable solution, the high cost and uneven distribution of lithium reserves limits the widespread application of LIBs for grid energy storage. Considering these developments and the challenges posed by limited lithium reserves, sustainable and low-cost sodium-ion batteries (SIBs) emerge as a promising alternative.Among the various battery electrode materials, manganese dioxide (MnO2) stands out as a promising choice for large-scale energy storage applications due to its earth abundance, cost-effectiveness and non-toxic nature. Although MnO2 is known as a pseudocapacitive material with superior cycling stability in aqueous electrolytes, its dissolution in non-aqueous electrolytes has restricted its widespread use in long lifetime batteries. In this study, we demonstrate that an ether-based electrolyte solution (1M NaClO4 in diglyme) is able to achieve stable cycling of electrodeposited ε-MnO2 as a cathode for SIBs, reaching a over 75% capacity retention over 1000 cycles. This response surpasses conventional ester-based electrolytes (58% of 1M NaClO4 in EC/PC). A comparative cycling stability study, coupled with electrochemical quartz crystal microbalance characterization, validates the efficacy of the ether-based electrolyte in mitigating MnO2 dissolution. Furthermore, the integration of 3D printed graphene aerogel (3D GA) as a scaffold for electrodeposited MnO2 leads to enhanced electrochemical performance of the MnO2 electrode (3D MnO2/GA), resulting in a high areal capacity of 4.4 mAh cm-2 at a current density of 10 mA cm-2. The 3D MnO2/GA electrode possesses scalable electrochemical performance with mass loadings from 20 mg cm-2 to 80 mg cm-2. Using this electrode, a high mass loaded sodium-ion battery (SIB) device was fabricated by using utilizing 58 mg cm-2 3D MnO2/GA as the cathode and 16 mg cm-2 dip-coated TiO2@Cu foam as the anode. This MnO2 | TiO2 device delivered a notable areal capacity of 6.2 mWh cm-2 and a high areal power density of 70.7 mW cm-2. Moreover, the SIB device demonstrates 85% capacity retention after 500 cycles, underscoring the stable cycling of this high-energy and power-density SIB device.

Enhancing Zn-MnO2 Battery Performance with Hydrogen-Bonded MnO2 Interfaces in Wet Nonaqueous Electrolytes

The quest for sustainable and high-performing battery technologies has directed attention towards Zinc (Zn)-manganese dioxide (MnO2) based rechargeable batteries. These batteries emerge as a viable alternative to lithium-ion systems, particularly due to their advantageous raw material supply, cost, and performance parameters. Despite their potential, Zn-MnO2 batteries face operational challenges, including gas evolution, Zn self-corrosion, and dissolution of the host material when utilized in mild acid aqueous electrolytes. Addressing these issues, our research explores the efficacy of wet nonaqueous electrolytes as a solution. Previously, we demonstrated a substantial enhancement in battery performance (~200 mAh/g of MnO2) by incorporating a specific proportion of water into the nonaqueous electrolyte. Building on this foundation, our current study investigates the role of hydrogen-bonded pillars, particularly proton and ammonium cations, in augmenting the interfacial properties of MnO2. This modification aims to bolster surface kinetics, thereby elevating battery performance closer to that of aqueous systems. Employing a suite of material characterization techniques, including in-situ X-ray absorption spectroscopy (XAS), Raman spectroscopy, and synchrotron X-ray diffraction (XRD), we observed a notable performance improvement (~270 mAh/g), while maintaining stability. These findings hold significant promise for advancing the practical application of MnO2-based hosts in Zn-MnO2 batteries, marking a stride towards next-generation energy storage solutions.