Differences In Microstructure Research Articles

Age-related Differences in Response Inhibition Are Mediated by Frontoparietal White Matter but Not Functional Activity.

Healthy older adults often exhibit lower performance but increased functional recruitment of the frontoparietal control network during cognitive control tasks. According to the cortical disconnection hypothesis, age-related changes in the microstructural integrity of white matter may disrupt inter-regional neuronal communication, which in turn can impair behavioral performance. Here, we use fMRI and diffusion-weighted imaging to determine whether age-related differences in white matter microstructure contribute to frontoparietal over-recruitment and behavioral performance during a response inhibition (go/no-go) task in an adult life span sample (n = 145). Older and female participants were slower (go RTs) than younger and male participants, respectively. However, participants across all ages were equally accurate on the no-go trials, suggesting some participants may slow down on go trials to achieve high accuracy on no-go trials. Across the life span, functional recruitment of the frontoparietal network within the left and right hemispheres did not vary as a function of age, nor was it related to white matter fractional anisotropy (FA). In fact, only frontal FA and go RTs jointly mediated the association between age and no-go accuracy. Our results therefore suggest that frontal white matter cortical "disconnection" is an underlying driver of age-related differences in cognitive control, and white matter FA may not fully explain functional task-related activation in the frontoparietal network during the go/no-go task. Our findings add to the literature by demonstrating that white matter may be more important for certain cognitive processes in aging than task-related functional activation.

Impact of electron beam welding on the microstructure of PM2000 ODS steel

This work investigated the impact of electron beam (EB) welding, using various traverse speeds of the electron beam (1200–2200 mm/min), on the microstructure of PM2000 ODS steel which was characterized using analytical electron microscopy and microhardness. The different heat inputs during welding explored in this study (72–39 J/mm), related to the traverse speed used, correlated with small differences in the widths of the fusion zone. Only minor differences in local microstructures and hardness of the fusion zones were detected amongst the four butt welds produced. The fusion zone is characterized by large columnar grains in the ferritic matrix, together with a coarsened Y-Al-O particle distribution and a reduction in its particle number density as compared to the base material. There is also a sharp border between the fusion zone and base material, with the joint showing little evidence of a heat-affected zone. These changes in microstructure during welding led to a hardness reduction of ∼30 % in the fusion zone of the welds with respect to the base material.

Role of LRP5/6/GSK-3β/β-catenin in the differences in exenatide- and insulin-promoted T2D osteogenesis and osteomodulation.

Insulin and exenatide are two hypoglycaemic agents that exhibit different osteogenic effects. This study compared the differences between exenatide and insulin in osseointegration in a rat model of Type 2 diabetes (T2D) and explored the mechanisms promoting osteogenesis in this model of T2D. In vivo, micro-CT was used to detect differences in the peri-implant bone microstructure in vivo. Histology, dual-fluorescent labelling, immunofluorescence and immunohistochemistry were used to detect differences in tissue, cell and protein expression around the implants. In vitro, RT-PCR and western blotting were used to measure the expression of osteogenesis- and Wnt signalling-related genes and proteins in bone marrow mesenchymal stromal cells (BMSCs) from rats with T2D (TBMSCs) after PBS, insulin and exenatide treatment. RT-PCR was used to detect the expression of Wnt bypass cascade reactions under Wnt inactivation. Micro-CT and section staining showed exenatide extensively promoted peri-implant osseointegration. Both in vivo and in vitro experiments showed exenatide substantially increased the expression of osteogenesis-related and activated the LRP5/6/GSK-3β/β-catenin-related Wnt pathway. Furthermore, exenatide suppressed expression of Bmpr1a to inhibit lipogenesis and promoted expression of Btrc to suppress inflammation. Compared to insulin, exenatide significantly improved osteogenesis in T2D rats and TBMSCs. In addition to its dependence on LRP5/6/GSK-3β/β-catenin signalling for osteogenic differentiation, exenatide-mediated osteomodulation also involves inhibition of inflammation and adipogenesis by BMPR1A and β-TrCP, respectively.

Study on the solder flow in a narrow gap with metal surface texture

Obvious voids in the solder in a narrow gap is a common problem that greatly affects the reliability of mechanical connections. Due to its high heating rate, laser soldering causes more severe voids and even evolves into dispersion of the solder. A method of metal surface texturing is put forward, in which the texture gradient is used to directionally transport solder for lower dispersity, and the pattern design of texture is used to reduce the void rate. The directional transport of solder is realized through the differences in oxidation degree and microstructure of stainless steel surface under different ultrafast laser scanning speeds. The discharge of voids in the solder is achieved through the reservation of the central area in the solder and the oscillation during the laser heating process. Based on the present method, the aggregation of solder is achieved, with the void rate of 18 % and the joining strength of 10.4 MPa.

Effect of Pre-Weld Heat Treatment on the Microstructure and Properties of Coarse-Grained Heat-Affected Zone of a Wind Power Steel after Simulated Welding

The effect of pre-weld heat treatment on the microstructure and low-temperature impact toughness of the coarse-grained heat-affected zone (CGHAZ) after simulated welding was systematically investigated through the utilization of scanning electron microscopy (SEM) and electron back-scattering diffraction (EBSD). The Charpy impact test validated the presence of an optimal pre-weld heat treatment condition, resulting in the highest impact toughness observed in the CGHAZ. Three temperatures for pre-weld heat treatment (690, 720 and 750 °C) were used to obtain three different matrices (Steel 1, Steel 2, Steel 3) for simulated welding. The optimal pre-weld heat treatment is 720 °C for 15 min followed by water quench. Microstructure characterization showed that there is an evident microstructure comprising bainite (B) in Steel 1 and Steel 2 after pre-weld heat treatment, while the addition of martensite (M) with the pre-weld heat treatment temperature exceeds Ac1 by almost 60 °C (Steel 3). These differences in microstructures obtained from pre-weld heat treatment influence the refinement of high-temperature austenite during subsequent simulated welding reheating processes, resulting in distinct microstructural characteristics in the CGHAZ. After the optimal pre-weld heat treatment, Steel 2 subjected to single-pass welding thermal simulation demonstrates a refined microstructure characterized by a high density of high-angle grain boundaries (HAGBs) within the CGHAZ, particularly evident in block boundaries. These boundaries effectively prevent the propagation of brittle cracks, thereby enhancing the impact toughness.

Anionic Conjugate Addition Oligomerization of Carbon Dioxide/Butadiene Derived Lactones.

Nucleophilic and non-nucleophilic bases have been employed in anionic oligomerization of unsaturated δ-valerolactone (3-ethylidene-6-vinyltetrahydro-2H-pyran-2-one) (1). Compared to the seminal findings with 1,5,7-triazabicyclo[4.4.0]dec-5-ene (TBD), the unsaturated lactone reacts with guanidines, disilazanes, and phosphazenes both in bulk and in solution with higher productivities and activities, reaching full conversion with turnover frequencies up to 382 h-1. Additionally, reactions using phosphazenes and NaHMDS were active at 1 mol % catalyst loadings both in solvent and in bulk monomer at room temperature. Characterization of the reaction products by 1H, 13C, FTIR, MALDI-MS, tandem mass spectrometry (MS/MS), and ion mobility mass spectrometry (IM-MS) revealed microstructural differences dependent on the nucleophilicity of the organocatalytic base and reaction conditions. The products from phosphazene-catalyzed reactions are consistent with selective vinylogous 1,4-conjugate addition, whereas both conjugate addition and ring-opening mechanisms are observed in TBD. DSC reveals that these microstructures can be tuned to have a Tg range between -18 and 80 °C, while SEC and MALDI-MS reveal that only low molar mass oligomers are formed (748-5949 g/mol). From these results, an approach for selectively favoring the vinylogous 1,4-conjugate addition pathway is obtained over ring-opening reactivity.

Deep learning with diffusion MRI as in vivo microscope reveals sex-related differences in human white matter microstructure

Biological sex is a crucial variable in neuroscience studies where sex differences have been documented across cognitive functions and neuropsychiatric disorders. While gross statistical differences have been previously documented in macroscopic brain structure such as cortical thickness or region size, less is understood about sex-related cellular-level microstructural differences which could provide insight into brain health and disease. Studying these microstructural differences between men and women paves the way for understanding brain disorders and diseases that manifest differently in different sexes. Diffusion MRI is an important in vivo, non-invasive methodology that provides a window into brain tissue microstructure. Our study develops multiple end-to-end classification models that accurately estimates the sex of a subject using volumetric diffusion MRI data and uses these models to identify white matter regions that differ the most between men and women. 471 male and 560 female healthy subjects (age range, 22–37 years) from the Human Connectome Project are included. Fractional anisotropy, mean diffusivity and mean kurtosis are used to capture brain tissue microstructure characteristics. Diffusion parametric maps are registered to a standard template to reduce bias that can arise from macroscopic anatomical differences like brain size and contour. This study employ three major model architectures: 2D convolutional neural networks, 3D convolutional neural networks and Vision Transformer (with self-supervised pretraining). Our results show that all 3 models achieve high sex classification performance (test AUC 0.92–0.98) across all diffusion metrics indicating definitive differences in white matter tissue microstructure between males and females. We further use complementary model architectures to inform about the pattern of detected microstructural differences and the influence of short-range versus long-range interactions. Occlusion analysis together with Wilcoxon signed-rank test is used to determine which white matter regions contribute most to sex classification. The results indicate that sex-related differences manifest in both local features as well as global features / longer-distance interactions of tissue microstructure. Our highly consistent findings across models provides new insight supporting differences between male and female brain cellular-level tissue organization particularly in the central white matter.

The Influence of Residual Stress on Fatigue Crack Growth Rates in Stainless Steel Processed by Different Additive Manufacturing Methods

The Influence of Residual Stress on Fatigue Crack Growth Rates in Stainless Steel Processed by Different Additive Manufacturing Methods

Children with Congenital Heart Diseases Exhibit Altered Deep Gray Matter Structures.

Children with congenital heart diseases (CHDs) have an increased risk of developing neurologic deficits, even in the absence of apparent brain pathology. The aim of this work was to compare quantitative macro- and microstructural properties of subcortical gray matter structures of pediatric CHD patients with normal appearing brain magnetic resonance imaging to healthy controls. We retrospectively reviewed children with coarctation of the aorta (COA) and hypoplastic left heart syndrome (HLHS) admitted to our hospital. We identified 24pediatric CHD patients (17COA, 7HLHS) with normal-appearing brain MRI. Using an atlas-based approach, the volume and apparent diffusion coefficient (ADC) were determined for the thalamus, caudate, putamen, pallidum, hippocampus, amygdala, nucleus accumbens, cerebral white matter, cerebral cortex, and brainstem. Multivariate statistics were used to compare the extracted values to reference values from 100 typically developing children without any known cardiac or neurological diseases. Multivariate analysis of covariance using the regional ADC and volume values as dependent variables and age and sex as co-variates revealed asignificant difference between pediatric CHD patients and healthy controls (p < 0.001). Post-hoc comparisons demonstrated significantly reduced brain volumes in most subcortical brain regions investigated and elevated ADC values in the thalamus for children with CHD. No significant differences were found comparing children with COA and HLHS. Despite normal appearing brain MRI, children with CHD exhibit wide-spread macro-structural and regional micro-structural differences of subcortical brain structures compared to healthy controls, which could negatively impact neurodevelopment, leading to neurological deficits in childhood and beyond.

Using multiscale second phases to fabricate high-performance Mg-3Al-3Nd-0.1Mn alloys with bimodal grain structures

The quest for magnesium alloys that combine high strength and high ductility drives significant research effort aimed at broadening their use in various sectors. In this research, a low-alloy Mg-3Al-3Nd-0.1Mn (AEM330) was successfully prepared through Hard Plate Rolling (HPR), achieving an ideal combination of high strength and ductility via carefully modifying grain structure at lower rolling temperature. The optimized processing conditions led to an alloy with an ultimate tensile strength of 427 MPa and an notable elongation of 11.4 %. The AEM330 processed by HPR displayed unique bimodal grain structure with coarse grains (CGs) sizes ∼13.66 µm and fine grains (FGs) sizes ∼2.36 µm, and their strength and ductility were found to be directly related to the microstructural differences between CGs and FGs. A crucial discovery of this study is the essential role of the Al2Nd phase (larger than 1 µm) and the Al11Nd3 phase (smaller than 1 µm) in forming bimodal grain structure. The former phase plays a significant role in recrystallization by particle-stimulated nucleation (PSN), and the latter restricts grain size via Zener pinning. Furthermore, it was found that the ratio of CGs to FGs could be controlled by modifying the rolling temperature. Importantly, the simple composition and direct shaping process of the AEM330 alloy not only improve its cost-effectiveness but also streamline the manufacturing process; thus, enhancing its potential for broad industrial use.

Size matters: Exploring part size effects on microstructure, defects, and mechanical property in optimized laser powder bed fusion (L-PBF) additive manufacturing

In laser-based metal additive manufacturing (MAM), effective process optimization requires a thorough analysis of variations across the process window. Despite the common practice of utilizing small-sized coupons to optimize process parameters in laser-based MAM, this study challenges this convention. Through an analysis of microstructure and defect differences in Fe-Ni material parts produced via laser-powder bed fusion (L-PBF), the study reveals significant discrepancies in microstructure, defect and mechanical property based on part size. As part size increases, lack-of-fusion defects and cracks become more pronounced, resulting in a decrease in density from 8.11 g/cm3 to 8.02 g/cm3, leading to constrained grain growth with a decrease of grain size from 41.88 μm to 23.07 μm in the scanning plane. Each defect and microstructural difference was traced back to variations in thermal history based on part size. Finite element method simulations, highlighting differences in thermal history from scanning a single layer to the entire part, showed that an increase in scan length with a widened scan area enlarged the period of the thermal history cycle, leading to considerable cooling. This study underscores crucial considerations for future researchers engaged in process optimization for novel alloy systems using laser-based MAM processes.

Innovative Ethanol Sensors Utilizing Organic Material Patterned Surface Acoustic Wave Detection

In this paper, sensor based on surface acoustic waves for ethanol vapors detection, was fabricated and studied. For room temperature detection of the volatile compound, a novel carbyne nanofilm was deposited on the surface of a SAW transducer. The conventional electrodes were replaced by conductive polymeric coting of poly(3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) to minimize the microstructural and elemental difference between the electrode and gas sensitive material. The experimental results showed that the sensors had a good response to ethanol at room temperature. The maximum response of the sensors was at 600 ppm, where the time delay between the output and the input signals of the transducer was ~ 160 μs. The parasitic contact resistance and interface capacitance were found insufficient to affect the accuracy of the measurement, although their values are higher as compared to the sensors with metal electrodes.

Biaxial flexural strength of hydrothermally aged resin-based materials

PurposeThe strength of temporary restorations plays a vital role in full-mouth reconstruction, and it can be impacted by the aging process. The aim of this in vitro study was to evaluate the biaxial flexural strength and fractographic features of different resin-based materials submitted to thermal aging. Material and methodsOne hundred and ninety-two resin disc-shaped specimens (6.5 mm in diameter and 0.5 mm in thickness) were fabricated and divided into six experimental groups according to the resin-based materials (Filtek Bulk-Fill flowable resin; J-Temp temporary resin; and Fuji Lining glass ionomer cement) and aging process (before and after thermal cycling). Biaxial flexural strength test was performed using a universal testing machine at a crosshead speed of 0.5 mm/min before and after thermal cycling (5 °C and 55 °C, 5760 cycles, 30 s). The mechanical properties were assessed using Weibull parameters (characteristic strength and Weibull modulus) (n = 30). Fractured specimens were examined under a polarized light stereomicroscope to identify crack origin and propagation direction. The surface microstructure of the resin-based materials was assessed by scanning electron microscopy (n = 2). The Weibull modulus (m), characteristic strength, and reliability properties were calculated, and a contour plot was used to detect differences among groups (95% confidence interval). ResultsThe Weibull modulus (m), characteristic strength, and reliability of the resin-based compounds were influenced by material type and thermal aging (p < 0.05). Weibull modulus (m) revealed no differences when comparing the materials and aging process (p > 0.05), except for the preceding aging period where Filtek Bulk-Fill exhibited higher values compared to J-Temp (p < 0.05). Filtek Bulk-Fill demonstrated superior characteristic strength and reliability compared to J-Temp and Fuji Lining before and after thermal cycling (p < 0.05). Fractography of the resin-based materials showed fractures originating from surface defects exposed to tensile side and their propagation toward the compressive side. Generally, no differences in surface microstructure were observed on micrographs before and after thermal aging for Filtek Bulk-Fill and Fuji Lining. However, the aging process developed flaws in J-Temp. ConclusionResin-based material composition resulted in different flexural strength performance, impacting the Weibull modulus (m), characteristic strength, and reliability of the resin-based restorations.

Explaining the improving effect of dough crumb-sheet composite rolling on fresh noodle quality: From microstructure and moisture distribution perspective.

A new technique known as dough crumb-sheet composite rolling (DC-SCR) was used to improve the quality of fresh noodles. However, there is a dearth of theoretical investigations into the optimal selection of specific parameters for this technology, and the underlying mechanisms are not fully understood. Therefore, the effects of dough crumb addition times in DC-SCR on the texture, cooking, and eating quality of fresh noodles were first studied. Then, the underlying regulation mechanism of DC-SCR technology on fresh noodles was analyzed in terms of moisture distribution and microstructure. The study demonstrated that the most significant enhancement in the quality of fresh noodles was achieved by adding dough crumbs six times. Compared with fresh noodles made without the addition of dough crumbs, the initial hardness and chewiness of fresh noodles made by adding six times of dough crumbs increased by 25.32% and 46.82%, respectively. In contrast, the cooking time and cooking loss were reduced by 28.45% and 29.69%, respectively. This quality improvement in fresh noodles made by DC-SCR came from the microstructural differences of the gluten network between the inner and outer layers of the dough sheet. A dense structure on the outside and a loose structure on the inside could endow the fresh noodles made by DC-SCR with higher hardness, a shortened cooking time, and less cooking loss. This study would provide a theoretical and experimental basis for creating high-quality fresh noodles.

Tracts in the limbic system show microstructural alterations post COVID-19 recovery.

Delirium, memory loss, attention deficit and fatigue are frequently reported by COVID survivors, yet the neurological pathways underlying these symptoms are not well understood. To study the possible mechanisms for these long-term sequelae after COVID-19 recovery, we investigated the microstructural properties of white matter in Indian cohorts of COVID-recovered patients and healthy controls. For the cross-sectional study presented here, we recruited 44 COVID-recovered patients and 29 healthy controls in New Delhi, India. Using deterministic whole-brain tractography on the acquired diffusion MRI scans, we traced 20 white matter tracts and compared fractional anisotropy, axial, mean and radial diffusivity between the cohorts. Our results revealed statistically significant differences (PFWE < 0.01) in the uncinate fasciculus, cingulum cingulate, cingulum hippocampus and arcuate fasciculus in COVID survivors, suggesting the presence of microstructural abnormalities. Additionally, in a subsequent subgroup analysis based on infection severity (healthy control, non-hospitalized patients and hospitalized patients), we observed a correlation between tract diffusion measures and COVID-19 infection severity. Although there were significant differences between healthy controls and infected groups, we found no significant differences between hospitalized and non-hospitalized COVID patients. Notably, the identified tracts are part of the limbic system and orbitofrontal cortex, indicating microstructural differences in neural circuits associated with memory and emotion. The observed white matter alterations in the limbic system resonate strongly with the functional deficits reported in Long COVID. Overall, our study provides additional evidence that damage to the limbic system could be a neuroimaging signature of Long COVID. The findings identify targets for follow-up studies investigating the long-term physiological and psychological impact of COVID-19.

Nondestructive internal disorders detection of ‘Braeburn’ apple fruit by X-ray dark-field imaging and machine learning

'Braeburn' apples are susceptible to internal browning disorders when stored under controlled atmosphere (CA) conditions with unfavorable gas compositions. The progression of CA-related disorders in apple tissues is dynamic, noting a decrease in porosity during early storage due to cellular breakdown and pore flooding, and an increase in porosity in later stages due to structural collapse and cavity formation. Utilizing grating-based X-ray dark-field radiography, which leverages X-ray small-angle scattering to detect microstructural changes below the pixel scale, this study assesses the technique's efficacy in identifying internal disorders in 'Braeburn' apples at both early and later stages. A machine learning approach was applied to compare the diagnostic capabilities of dark-field imaging with those of X-ray absorption radiography at identical image resolutions. Results indicate that for early-stage disordered fruit detection, X-ray dark field radiography is 10 % more accurate than absorption radiography, regardless of the machine learning classifiers that were applied. In the later stage of browning, dark-field imaging performs similarly to absorption imaging. High-resolution micro-computed tomography scans suggested that the distinct detection performance of dark-field imaging may be attributed to the more pronounced microstructural differences between healthy and early-stage defective tissues than those between healthy and later-stage defective tissues. The insights from this work will guide the application of X-ray dark-field systems in fruit quality assurance, particularly in detecting internal disorders.

Microstructural Properties of the Cerebellar Peduncles in Children With Developmental Language Disorder

Abstract Children with developmental language disorder (DLD) struggle to learn their native language for no apparent reason. While research on the neurobiological underpinnings of the disorder has focused on the role of corticostriatal systems, little is known about the role of the cerebellum in DLD. Corticocerebellar circuits might be involved in the disorder as they contribute to complex sensorimotor skill learning, including the acquisition of spoken language. Here, we used diffusion-weighted imaging data from 77 typically developing and 54 children with DLD and performed probabilistic tractography to identify the cerebellum’s white matter tracts: the inferior, middle, and superior cerebellar peduncles. Children with DLD showed lower fractional anisotropy (FA) in the inferior cerebellar peduncles (ICP), fiber tracts that carry motor and sensory input via the inferior olive to the cerebellum. Lower FA in DLD was driven by lower axial diffusivity. Probing this further with more sophisticated modeling of diffusion data, we found higher orientation dispersion but no difference in neurite density in the ICP of children with DLD. Reduced FA is therefore unlikely to be reflecting microstructural differences in myelination, rather the organization of axons in these pathways is disrupted. ICP microstructure was not associated with language or motor coordination performance in our sample. We also found no differences in the middle and superior peduncles, the main pathways connecting the cerebellum with the cortex. To conclude, it is not corticocerebellar but atypical olivocerebellar white matter connections that characterize DLD and suggest the involvement of the olivocerebellar system in speech and language acquisition and development.

Effect of difference in microstructure of rare refractory metal silicate doping matrix on oxidation behavior and mechanism of C/SiC composites

Doping refractory metal silicates into the matrix of C/SiC composites is an effective means to improve their oxidation resistance. Previous studies have demonstrated that doping HfSiO4 matrix availably enhanced the oxidation resistance of C/SiC composites, but the high raw material cost of HfSiO4 limits its widespread application. This paper attempts to introduce ZrSiO4 matrix, which has lower raw material cost and similar properties to HfSiO4, into C/SiC matrix through the same process. To clarify whether the microstructure of the refractory metal silicate doped matrix significantly impacts the oxidation behavior of C/SiC composites, the preparation temperature of ZrSiO4 was increased to 1100 °C. The densification effect, oxidation behavior, and related mechanisms of C/SiC composites doped with ZrSiO4 matrix were investigated and compared in detail with the previously studied C/SiC composites doped with HfSiO4 matrix. Results show that the oxidation resistance behavior of C/SiC composites is relatively sensitive to the microstructure of the refractory metal silicate-doped matrix. At lower preparation temperatures of refractory metal silicates, the particle size of the composite matrix is significantly refined, which is conducive to improving the matrix densification degree of the composites and protecting more carbon fibers from erosion by the oxidizing environment, thus achieving a better oxidation resistance modification effect.

Morphological and functional analyses for investigation of sexually selected legs in the frog legged beetle Sagra femorata (Coleoptera: Chrysomelidae)

Mate choice and male–male combat over successful mating often cause disproportionate exaggeration of male trait relative to body size. However, the exaggeration is often not the only trait involved with male–male combat and mate choice: suites of co-expressed traits may function together as a coordinated unit. When this occurs, dimorphism may be expected for these additional, non-exaggerated, structures. S. femorata males have disproportionately large hind-legs used in male–male combat over females. During the fights, fore- and mid-legs are used to keep males in positions where advantageous for leverage. Because use of the exaggerated hind-legs is coordinated with the other legs, they will coevolve as a functional unit. Here, we show that 1) S. femorata has sexual size differences in all three legs; 2) males show positive allometry in the relative sizes of all three legs; and 3) microstructures of tarsi on the fore- and mid-legs are also sexually dimorphic. Despite these differences in the tarsal microstructure, 4) adhesion forces of the tarsi had no sexual difference in flat surface. The microstructure would be specialized on attaching elytra surface. These results suggest that the three pairs of legs function together during fighting behavior, with hind-legs employed primarily for fighting, and the fore- and mid-legs functioning to grip females, keeping males positioned on the back of the female during combat.

Effects of non-isothermal annealing on the microstructure of pure and potassium-doped tungsten sheets

Within this study, the effects of non-isothermal annealing procedures, especially different heating rates, were studied for cold rolled pure and potassium doped tungsten sheets. The sheets had a thickness of 0.2 mm. The microstructure was studied via etching of polished cross sections as well as electron backscatter diffraction. The potassium-bubble distribution in the doped tungsten sheets was investigated using scanning electron microscopy.Regarding the microstructure, the doped tungsten sheets presented an elongated, layered microstructure, that was considerably affected by the heating rate. A decrease of the heating rate from 14,400 K/min to 20 K/min resulted in a grain size shift in rolling direction from 70 to 513 μm. On the other hand, pure tungsten sheets showed no significant dependence on the heating rate. Moreover, additional isothermal annealing periods at 2400 °C did generally not affect the microstructure of doped tungsten sheets, which in turn led to a significant increase of the grain size in pure tungsten. This difference was attributed to the grain growth mechanisms, normal grain growth for pure and secondary recrystallization for K-doped tungsten.However, the potassium bubble structure, being responsible for the microstructural differences, was in turn only affected by the maximum annealing temperature. The heating rate differences led to no significant changes in the bubble size distribution. Furthermore, additional isothermal annealing at 2400 °C led to comparably minor changes in the average bubble diameter.