Microalgal Biomass Research Articles

Capture CO2 from flue gases during the cultivation of cyanobacteria/microalgae Arthrospira platensis

Experimental studies and assessment of the state of cyanobacteria/microalgae Arthrospira platensis in a sustainable consortium with heterotrophic bacteria were carried out grown by bubbling culture medium with microalgae by a mixture of flue gases and air. The investigations were carried out in an experimental sample of a gas chamber with photobioreactors, which was supplemented by a designed flue gas generation system. The CO2 content in the gas mixture was 3, 6, and 8%. The resulting growth rate of microalgae biomass density was 0.21 g/l per day at CO2 concentrations of 3 and 6%, 0.27 g/l per day at 8%. The present growth rate was 1.75 – 2.25 times higher than the growth rate in experiments conducted when growing this microalga in mixtures of air and CO2. An increase in the amount of carbohydrates in biomass to 29.4% and the lipid content at the level of 21 – 23% was recorded, which makes biomass attractive for biofuel production.

Shaping Sustainable Bioplastics: Illuminating Chlorella sp. Growth with Light Variations and NPK Levels

this study delved into the exploration of a biodegradable alternative to synthetic plastics through the production of biodegradable bioplastics derived from microalgae. The investigation suggests that utilizing <i>Chlorella </i>sp. as a viable source for sustainable biomass in bioplastic creation holds promise due to the convenience of microalgae cultivation and its rapid growth rate. However, the large-scale cultivation of microalgae requires a considerable amount of nutrients, posing challenges to its economic viability. To address this hurdle, it becomes imperative to prioritize the enhancement of growth parameters for microalgae development. This study endeavors to identify the optimal NPK (nitrogen, phosphorus, and potassium) concentration and light spectrum for <i>Chlorella </i>sp. using a cost-effective NPK fertilizer medium. Various combinations of light spectra and NPK levels were examined to optimize growth conditions. Cultures of <i>Chlorella</i> sp. were subjected to red (660 nm), blue (460 nm), and white light (380 ~ 760 nm) which acted as experimental control over a span of 10 days. Among these, blue light yielded the highest optical density at 0.687, while red light exhibited the lowest optical density at 0.349. The findings underscore that the quantity of NPK fertilizer employed as a growth medium correlate directly with the observed cellular growth in <i>Chlorella</i> sp. cultures. The study also encompassed tensile strength and biodegradability assessments to characterize the resulting bioplastics. Tensile tests disclosed that bioplastics synthesized with sorbitol displayed a lower tensile strength of 0.106 MPa, in contrast to bioplastics containing both sorbitol and chitosan, which demonstrated a tensile strength of 0.167 MPa. In conclusion, both the appropriate light wavelengths and NPK nutrients emerge as pivotal factors influencing photosynthesis and the growth of photoautotrophic microalgae. The overarching objective of this research was achieved by successfully producing bioplastics using microalgae biomass residue cultivated under optimized parameters.

Artificial Intelligence-based Flow Cytometer for Real-time Algae Monitoring

Flow cytometry is a laser-based technology that rapidly detects and analyzes the chemical and physical characteristics of single cells or particles and is already well established in environmental and toxicological studies for microalgae and bacterial quantification. This study introduces an imaging Flow Cytometer (FC) system, designed specifically for the enhanced analysis of microalgae biomass populations and aggregate groups through Artificial Intelligence (AI) integration. The FC incorporates a single flow line, critical hardware components, and a trifurcated software setup. The system employs a multi-step process for counting algae units and an Artificial Neural Network (ANN) for classifying them in groups of two or four. To demonstrate its capabilities, the system was tested on its ability to capture, count, and categorize algal units, specifically the Desmodesmus sp. morphotype with high accuracy. Furthermore, the FC's capabilities were contrasted with traditional counting methods, validating its enhanced precision and efficiency against a hematocytometer. With its capability to provide rapid, accurate, and high-throughput analyses, this innovative FC paves the way for a revolutionary approach to cellular research.

Biodiesel from blended microalgae and waste cooking oils: Optimization, characterization, and fuel quality studies

<abstract> <p>Petrodiesel is an unsustainable and undependable fuel owing to its environmental concerns and depleting reserves. Biodiesel is a sustainable alternative fuel to petrodiesel with a better fuel quality and minimum environmental impacts. However, cost-effective biodiesel production requires the use of a sustainable feedstock and process optimization. This study explored biodiesel yield optimization from mixed microalgae oil (MO) and waste cooking oil (WCO). The use of mixed feedstock for biodiesel production relieves the rising demands; lowers feedstock costs; and improves the fuel quality, engine performance, and pollutants emission characteristics. MO was extracted from dried microalgae biomass by the Soxhlet method using hexane. The MO and WCO were purified and characterized, and an oil blend with suitable properties (best in kinematic viscosity, density, higher heating value, and acid value compared to other blends) was selected. The transesterification experiments designed by central composite design were optimized using the response surface methodology. Experimental results underwent regression analysis to develop a quadratic model equation for predicting the optimum level of parameters and biodiesel yield. Model fitness and variables effects on biodiesel yield were studied using analysis of variance. The optimization experiment achieved 98.82% oil conversion rate at the catalyst loading of 2.0 w/v%, molar ratio of 12:1 v/v, reaction temperature of 60 ℃, and reaction time of 100 min. A triplicate validation experiments achieved 97.72% conversion rate, which is very close to the model predicted result (99.1%). Biodiesel from MO-WCO showed a better cetane number (77.76), iodine value (12.90 gI<sub>2</sub>/100 g), acid value (0.049 mg KOH/g), HHV (43.25 MJ/kg), kinematic viscosity (4.50 mm<sup>2</sup>/s), pour point (–2.5 ℃), and flash point (180 ℃). In conclusion, the study revealed that transesterification of blended MO-WCO led to a maximum biodiesel and the reaction time and temperature were found to be the most significant factors affecting the yield of biodiesel. Furthermore, biodiesel from blended MO-WCO is a sustainable and environmentally friendly alternative fuel source which can contribute towards a promising industrial scale biodiesel production in the future.</p> </abstract>

Removals of Some High- and Low-Density Polyethylene (HDPE and LDPE), Polypropylene (PP) and Polyvinyl Chloride (PVC) Microplastics Using Some Microalgae Types, Energy Production and Energy Recovery

Waste plastic conversion involves the treatment of plastic waste to transform in different forms of energy (heat, electricity, liquid fuels). Plastic can be converted into different forms of biofuel via thermochemical conversion methods (gasification, pyrolysis and liquefaction). Algal biomass can be converted into different forms of biofuel (crude bio-oil, bioethanol, biogas, biodiesel and bio-hydrogen) well as value added chemicals. Microalgal cells can accumulate more lipids over a shorter life cycle, they are discussed as a promising feedstock for third-generation biodiesel. The utilization of microalgae as biofuel feedstocks offers an economic, ecofriendly alternative to the use of fossil fuels the aim of microplastics (MPs) removals. Interactions between MPs and microalgal cells could enhance several important features for possible microalgal harvest and MPs accumulation. One hypothesis is microalgal biomass hypothesis can accumulate lipids and carbohydrates under microplastic stress, supporting biomass conversion into biodiesel and bioethanol. In such systems, algal cells act as bio-scavengers for MPs, binding the particles to algal surfaces or incorporating them into their cells; they are filtered from the water body and finally destroyed by further downstream processing of the polluted biomass. In this study, in order to determine biofuel (1-butanol) and methane gas [CH4(g)] production; High- and low-density polyethylene (HDPE and LDPE), polypropylene (PP), and polyvinyl chloride (PVC) MPs were removed using biomass composed of microalgae Chlamydomonas reinhardtii and Chlorella vulgaris. The algal inhibition test results proved that small groups of MPs with a size of ≈ 100 nm did not show algal inhibition. According to the algae inhibition test results, the production of 1-butanol from 100 mg/l microalgae biomass under aerobic conditions were determined as 93 ml/g for HDPE, 236 ml/g for LDPE, 387 ml/g for PP and 459 ml/g for PVC. According to the algae inhibition test results, the production of CH4(g) from 400 mg/l microalgae biomass under anaerobic conditions were measured as 452 ml/g for HDPE, 510 ml/g for LDPE, 529 ml/g for PP and 541 ml/g for PVC. 91.26%, 94.52%, 98.34% and 96.17% energy recoveries were measured for HDPE, LDPE, PP and PVC MPs, respectively, after microalgae biomass experiments, at pH=7.0 and at 35oC. Maximum 98.34% energy recovery was obtained for PP MPs after microalgae biomass experiments, at pH=7.0 and at 35oC.

Ultrafiltration Harvesting of Microalgae Culture Cultivated in a WRRF: Long-Term Performance and Techno-Economic and Carbon Footprint Assessment

A cross-flow ultrafiltration harvesting system for a pre-concentrated microalgae culture was tested in an innovative anaerobic-based WRRF. The microalgae culture was cultivated in a membrane photobioreactor fed with effluent from an anaerobic membrane bioreactor treating sewage. These harvested microalgae biomasses were then anaerobically co-digested with primary and secondary sludge from the water line. Depending on the needs of this anaerobic co-digestion, the filtration harvesting process was evaluated intermittently over a period of 212 days for different operating conditions, mainly the total amount of microalgae biomass harvested and the desired final total solids concentration (up to 15.9 g·L−1 with an average of 9.7 g·L−1). Concentration ratios of 15–27 were obtained with average transmembrane fluxes ranging from 5 to 28 L·m−2·h−1. Regarding membrane cleaning, both backflushing and chemical cleaning resulted in transmembrane flux recoveries that were, on average, 21% higher than those achieved with backflushing alone. The carbon footprint assessment shows promising results, as the GHG emissions associated with the cross-flow ultrafiltration harvesting process could be less than the emissions savings associated with the energy recovered from biogas production from the anaerobic valorisation of the harvested microalgae.

Optimization of Chromium (VI) Adsorption using Microalgae Biomass (Spirulina sp.) and its Application in Leather Tannery Waste

<p class="E-JOURNALAbstractBodyEnglish">This study was conducted to examine the adsorption of Cr (VI) metal using Spirulina sp (inactive) biomass and its application in leather tannery wastewater. The treatment was carried out to determine the influence of independent variables on Cr (VI) adsorption with variations in pH, contact time, and metal solution concentration. The values of the solution pH, adsorption time, and concentration of the best metal solution were used to determine the center points of the optimization variables through Response Surface Methodology (RSM). The results showed that based on the FTIR test, macromolecules present in Spirulina sp biomass included amino, carboxylate, and hydroxy groups. The combination of factor variables that produced the optimum response was at pH 3.165, contact time of 66.58 minutes, and Cr (VI) metal ion solution concentration of 22.9 mg/L, resulting in a Cr (VI) adsorption efficiency of 69.66%. The adsorption pattern was included in the Freundlich adsorption isotherm, and the application of Spirulina sp biomass adsorbent to tannery waste reduced the concentration of Cr (VI) from 3.9 g/L to an undetectable level at <1.4 g/L.</p>

Enhancing microalgal biomass production in lab-scale raceway ponds through innovative computational fluid dynamics-based electrode deflectors

The design of novel electrode deflector structures (EDSs) introduced a promising strategy for enhancing raceway ponds performance, increasing carbon fixation, and improving microalgal biomass accumulation. The computational fluid dynamics, based flow field principles, proved that the potency of arc-shaped electrode deflector structures (A-EDS) and spiral electrode deflector structures (S-EDS) were optimal. These configurations yielded superior culture effects, notably reducing dead zones by 9.1% and 11.7%, while elevating biomass increments of 14.7% and 11.5% compared to the control, respectively. In comparison to scenarios without electrostatic field application, the A-EDS group demonstrated pronounced post-stimulation growth, exhibiting an additional biomass increase of 11.2%, coupled with a remarkable 23.6% surge in CO2 fixation rate and mixing time reduction by 14.7%. A-EDS and S-EDS, combined with strategic electric field integration, provided a theoretical basis for promoting microalgal biomass production and enhancing carbon fixation in a raceway pond environment to similar production practices.

Bioengineering Phaeodactylum tricornutum, a marine diatom, for cannabinoid biosynthesis

Over the last few years, phytocannabinoids have been studied for their bioactive properties as potential drug candidates to treat or alleviate symptoms of several diseases. The isolation of single and pure cannabinoid (CB) from their natural source, i.e., Cannabis plants results in a low yield, diluted among hundreds of other plant metabolites. The use of biotechnological platforms to produce single CBs is appealing to the pharmaceutical industry. Therefore, our aim was to develop a sustainable system using the model diatom Phaeodactylum tricornutum to produce cannabigerolic acid (CBGA), the precursor to several CBs such as well-known cannabidiol (CBD) and delta-9-tetrahydrocannabinol (THC). We engineered P. tricornutum to express a mutant version of the Streptomyces sp. strain CL190's naptherpin biosynthetic cluster gene B NphB (Y288A/G286S, nphB), a non-Cannabis aromatic prenyltransferase enzyme, either by random integrated chromosomal expression (RICE) or extrachromosomal expression (EE), to maximize the success of protein production. The gene of nphB was linked to the reporter cyan fluorescent protein (CFP) and introduced in P. tricornutum. Clones were characterized by CFP fluorescence intensity, protein synthesis, enzymatic activity, and production of CBGA. We present, for the first time in diatoms, the successful production of a CB, CBGA up to 4.1 (± 0.2) mg/kg of microalgal fresh biomass weight. This work shows the potential of P. tricornutum as a sustainable controlled heterologous platform for CBs production, plant bioactive compounds, and relevant pharmaceuticals.

CO2 Capture Using Deep Eutectic Solvents Integrated with Microalgal Fixation

In this study, we investigated the use of functionalized deep eutectic solvents (DESs) as a medium for CO2 capture integrated with CO2 desorption and biofixation in microalgal culture, as an approach for carbon capture, utilization, and storage (CCUS). The newly devised DES formulation—comprising choline chloride, ethylene glycol, and monoethanolamine—demonstrated a significant advancement in CO2 absorption capacity compared with conventional solvents. Effective CO2 desorption from the solvent was also achieved, recovering nearly 90% of the captured CO2. We then examined the application of the functionalized DESs to promote microalgal cultivation using a Chlorella sp. strain. The experimental results indicated that microalgae exposed to DES-desorbed CO2 exhibited heightened growth rates and enhanced biomass production, signifying the potential of DES-driven CO2 capture for sustainable microalgal biomass cultivation. This research contributes to the growing field of CCUS strategies, offering an avenue for efficient CO2 capture and conversion into valuable biomasses, thereby contributing to both environmental sustainability and bioresource use.

Bicarbonate-assisted microalgae cultivation for drinking water RO reject recycling and bioproduct generation

This study undrapes a microalgae-mediated approach for recycling drinking water reverse osmosis (RO) reject with bicarbonate supplementation. Among the tested strains, Chlorella pyrenoidosa exhibited a significantly (p ≤ 0.05) higher biomass growth (760.81 ± 34.24 mg L−1) at 4.0 g L−1 bicarbonate in RO reject. Whereas Scenedesmus sp. showed the maximum biomass yield of 1041.81 ± 33.32 mg L−1 in RO reject without bicarbonate. Moreover, bicarbonate in RO reject promoted biofuel precursor synthesis, with Scenedesmus obliquus and Chlorella sorokiniana acquiring maximum carbohydrate (339.41 ± 13.68 mg L−1) and lipid (1453.57 ± 44.29 mg L−1) yields at 0.5 and 1.0 g L−1 bicarbonate, respectively. The fatty acid methyl ester (FAME) and theoretical methane potential (TMP) analyses showed improved biodiesel quality and biogas yield from bicarbonate-supplemented RO reject-grown microalgal biomass. Thus, the present findings inferred that bicarbonate supplementation to RO reject could be an economically feasible approach for RO reject recycling and microalgae-mediated resource recovery.

Enhanced microalgal biomass and lipid production with simultaneous effective removal of Cd using algae-bacteria-activated carbon consortium added with organic carbon source

Recently, using microalgae to remediate heavy metal polluted water has been attained a huge attention. However, heavy metals are generally toxic to microalgae and consequently decrease biomass accumulation. To address this issue, the feasibility of adding exogenous glucose, employing algae-bacteria system and algae-bacteria-activated carbon consortium to enhance microalgae growth were evaluated. The result showed that Cd2+ removal efficiency was negatively correlated with microalgal specific growth rate. The exogenous glucose alleviated the heavy metal toxicity to algal cells and thus increased the microalgae growth rate. Among the different treatments, the algae-bacteria-activated carbon combination had the highest biomass concentration (1.15 g L−1) and lipid yield (334.97 mg L−1), which were respectively 3.03 times of biomass (0.38 g L−1) and 4.92 times of lipid yield (68.08 mg L−1) in the single microalgae treatment system. Additionally, this algae-bacteria-activated carbon consortium remained a high Cd2+ removal efficiency (91.61%). In all, the present study developed an approach that had a great potential in simultaneous heavy metal wastewater treatment and microalgal lipid production.

Biosorption of Ciprofloxacin (CIP) using the Waste of Extraction Process of Microalgae: The Equilibrium Isotherm and Kinetic Study

Scientists are investigating the efficacy of different biosorbents for promoting economic and environmental viability in purifying contaminants. Among the primary by-products of biodiesel production is waste microalgae biomass, which has the potential to be used as a cheap biosorbent for the treatment of pollution. In the present study, the biomass left over after extracting the chlorella vulgaris was used to test the potential biosorption of CIP from simulated aqueous solutions. Bisorbent's ability was characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX). Analysis with a Fourier Transform Infrared Spectrometer revealed that CIP biosorption occurred mainly at biomass sites containing carboxyl and amino groups. The equilibrium isotherm data and biosorption kinetics were addressed in the present study. The biosorption data match the Langmuir isotherm model, and the maximal biosorption capacity was determined to be 7.56 mg/g. While The pseudo-second-order model accurately described the biosorption kinetic data. Biosorbent regeneration was also studied using two different sodium hydroxide concentrations, the results showing that after desorption, the biosorption capacity decreased from 5.2 to 3.74 and 1.77 (mg/g) using 0.1NaOH and 0.5NaOH, respectively.

A study on the designs of baffles-enhanced gas transfer inside Chlorella vulgaris airlift photobioreactors and flow visualisation modelling

Microalgae play a crucial role as bioresources, yet the culture systems of photobioreactors (PBR) encounter challenges. Many engineered PBRs tend to incorporate internals build-ups, serving photoautotroph production, and requiring substantial microalgal biomass. This study quantified the baffle effects on airlift flat plate PBRs based on the performance of Chlorella vulgaris. The impacts of baffle configurations, air velocity, and CO2 contents, three dominant parameters, on microalgae culture were investigated using culture experiments, numerical simulations, and flow visualisation techniques. The results demonstrate that multiple baffle design strategies enhance microalgae growth and production. On the 11th cultivation day, airflow rates of 6, 45, or 90 L/h produced 1.5, 3.0, or 1.9 times the biomass weight and 1.76 × 107 cell numbers/mL in PBRM with 24 baffles, compared to 1.44 × 107 cell numbers/mL in PBRC without baffles. Furthermore, it revealed an intensification in the generation potential of biocomponents with C–H, C = O, and C–O–C functional groups at a 45−50 L/h airflow rate and CO2 (20 %) aerated PBRM. Additionally, it presented the first visualisation explanation of the baffle-guided vortex flow pair symmetry PBRM. This study demonstrated enhancements by modelling newly proposed PBRs with baffles and high-valued bioproducts harvesting through the combination of culture parameters.

Influence of Seawater and Reaction Temperature on Biocrude Yield and Composition During Hydrothermal Liquefaction of Spirulina sp. Microalgal Biomass

Influence of Seawater and Reaction Temperature on Biocrude Yield and Composition During Hydrothermal Liquefaction of Spirulina sp. Microalgal Biomass

Bio-Nanoparticles Mediated Transesterification of Algal Biomass for Biodiesel Production

Immense use of fossil fuels leads to various environmental issues, including greenhouse gas emissions, reduced oil reserves, increased energy costs, global climate changes, etc. These challenges can be tackled by using alternative renewable fuels such as biodiesel. Many studies reported that biodiesel production from microalgae biomass is an environment-friendly and energy-efficient approach, with significantly improved fuel quality in terms of density, calorific value and viscosity. Biodiesel is produced using the transesterification process and the most sustainable method is utilizing enzymes for transesterification. Lipase is an enzyme with excellent catalytic activity, specificity, enantio-selectivity, compatibility and stability and hence it is applied in microalgae biodiesel production. But, difficulty in enzymatic recovery, high enzyme cost and minimal reaction rate are some of its drawbacks that have to be addressed. In this aspect, the nanotechnological approach of lipase immobilization in producing microalgae biodiesel is a promising way to increase production yield and it is due to the adsorption efficiency, economic benefit, recyclability, crystallinity, durability, stability, environmental friendliness and catalytic performance of the bio-nanoparticles used. Through increasing post-harvest biomass yield, absorption of CO2 and photosynthesis in the photobioreactor, the use of nanoparticle immobilized lipase during the generation of biodiesel from microalgae has the potential to also remove feedstock availability constraints. This review article discusses the production of microalgae biodiesel, and effect of nanoparticles and immobilized lipase nanoparticles on biodiesel production. The advantages of using lipase nanoparticles and the challenges in introducing the immobilized lipase on nanoparticles in large-scale microalgae biodiesel production are also discussed. Reducing the water and land use, energy and nutrient footprints of integrated algae-based operations must be the main goal of larger-scale experiments as well as ongoing research and development in order to expedite the adoption of microalgae-based biodiesel production. Also, the cost-effectiveness and large-scale availability of nanoparticles and the impact of lipase nanoparticles on engine performance should be analyzed for commercialization of microalgae biodiesel.

A kinetic-assisted growth curve prediction method for Chlamydomonas reinhardtii incorporating transfer learning

Traditional predictions of microalgal growth states rely on empirical or easily implementable kinetic models, leading to significant biases and elevated cost. This study proposes a kinetic-assisted machine learning method for predicting the growth curve of microalgal biomass under small sample conditions. Firstly, a microalgae growth kinetic model is constructed based on the logistic model. A two-stage kinetic fitting strategy is specified to account for the light–dark ratio. The Box-Behnken method is employed for experimental design. Then, using Two-stage TrAdaboost.R2 algorithm, the kinetic model is utilized as the source domain, and the experimental design data serves as the target domain for training machine learning models. The results indicate that the proposed method outperforms a single machine learning model in terms of prediction and has the potential to rapidly estimate microalgal growth trends under different conditions and accurately predict harvested biomass, potentially reducing the need for laborious, expensive, and time-consuming laboratory trials.

Tailored Fabrication of Plasmonic Film Light Filters for Enhanced Microalgal Growth and Biomass Composition.

Through plasmon resonance, silver and gold nanoparticles can selectively backscatter light within different regions of the visible electromagnetic spectrum. We engineered a plasmonic film technology that utilizes gold and silver nanoparticles to enhance light at the necessary wavelengths for microalgal photosynthetic activities. Nanoparticles were embedded in a polymeric matrix to fabricate millimeter-thin plasmonic films that can be used as light filters in microalgal photobioreactors. Experiments conducted with microalga Chlamydomonas reinhardtii proved that microalgal growth and photosynthetic pigment production can be increased by up to 50% and 78%, respectively, by using these plasmonic film light filters. This work provides a scalable strategy for the efficient production of specialty chemicals and biofuels from microalgae through irradiation control with plasmonic nanoparticles.

Mechanism of enhanced microalgal biomass and lipid accumulation through symbiosis between a highly succinic acid-producing strain of Escherichia coli SUC and Aurantiochytrium sp. SW1

Microalgae, known for rapid growth and lipid richness, hold potential in biofuels and high-value biomolecules. The symbiotic link with bacteria is crucial in large-scale open cultures. This study explores algal-bacterial interactions using a symbiotic model, evaluating acid-resistant Lactic acid bacteria (LAB), stress-resilient Bacillus subtilis and Bacillus licheniformis, and various Escherichia coli strains in the Aurantiochytrium sp. SW1 system. It was observed that E. coli SUC significantly enhanced the growth and lipid production of Aurantiochytrium sp. SW1 by increasing enzyme activity (NAD-IDH, NAD-ME, G6PDH) while maintaining sustained succinic acid release. Optimal co-culture conditions included temperature 28 °C, a 1:10 algae-to-bacteria ratio, and pH 8. Under these conditions, Aurantiochytrium sp. SW1 biomass increased 3.17-fold to 27.83 g/L, and total lipid content increased 2.63-fold to 4.87 g/L. These findings have implications for more efficient microalgal lipid production and large-scale cultivation.

Potentiality of natural live food organisms in shrimp culture: A review

The aquaculture industry is growing quickly due to increased fish consumption and a decline in wild fish catch. About half of the world's seafood demand for human consumption is now met by farmed seafood. The aquafeed market is expanding along with the aquaculture sector. Some of the elements in shrimp feed are derived from terrestrial plants and low-value forage fishes (fish meal). It is impossible to produce more fish meals since doing so would harm the ocean's environment and sustainability. The reduction in shrimp feed cost can also be done by introducing low-cost, environment-friendly ingredients in shrimp feed formulation. Therefore, new and ecologically friendly shrimp (Litopenaeus vannamei) feed component sources must be created. Live food organisms are a preferable option for this since they provide a variety of essential amino acids and beneficial triglycerides like fat, vitamins, and colors in their cell metabolites. Microalgae biomasses also represent feasible ingredients for shrimp feed sources. Their distinctive variety of bioactive chemicals can enhance color and pellet quality, act as a bulk element in shrimp feed, and boost the viability of farmed species. Live food organisms have a great economic potential since they have the highest biomass productivity of all photosynthetic organisms. In addition to giving farmers and exporters a better choice for feeding their fish, the availability of on-grown live food would also open up the prospect of improving the performance and quality of the fish and shrimp through bioencapsulation. This review study examines the possibility of generating natural food biomass as a component in shrimp feed.