Low Index Material Research Articles

Scattered-fields-induced tunable narrow resonance in low-index dielectric meta-lattices for transflective display

The development of a transflective display is important for reducing the energy consumption of an outdoor display-device. Currently, it is desirable to have a transflector which can be switched between its reflective and transparent states. The present work provides a novel yet simple route for the development of such a transflector based on one-dimensional (1D) meta-lattice systems. The system studied is shown capable of exciting tunable narrow resonance in the reflectance spectra through the generation of the scattered-field-induced polarizing-field in the system. Surprisingly, while most work on dielectric metasurface relies on high-index material, here it is found that the phenomenon can be achieved with common low-index material. Hence, it is a promising alternative for the development of future display technology with more economical operational cost.

Design and fabrication of highly efficient antireflective coating in MWIR on germanium using ion-assisted e-beam deposition

We present the design, fabrication, and characterization of a multilayer anti-reflective (AR) coating on a Germanium (Ge) substrate for mid-wavelength infrared (MWIR) applications using the ion-assisted electron-beam evaporation (IAPVD) technique. The AR coating structure comprises five layers of thin films, alternating between low (nL) and high (nH) refractive index materials, specifically silicon dioxide (SiO2) and Ge. The total thickness of the multilayer structure is maintained below 2 μm. The design was meticulously optimized for the 3.6–4.9 μm MWIR range using OptiLayer software, achieving an impressive average transmission of 99.492 % and an average reflectance of merely 0.508 % over a broadband spectral width of 1300 nm. Following the fabrication process using the IAPVD technique, the empirical results demonstrated an average transmission of 98.56 % and a reflectance value of 0.177 % within the 3.6–4.9 μm range. A strong correlation was observed between the simulated and the fabricated results, with a deviation of only 0.331 % on the reflectance value, proving the accuracy and reliability of the design and fabrication process. This work introduces a highly efficient solution for AR coatings on Ge surfaces, enhancing the performance of electro-optical applications in the MWIR region. To the best of our knowledge, the newly designed Ge/SiO2 multilayer structure and the results achieved have not been previously documented in the literature, and offer substantial improvements in transmission efficiency and reflectance reduction for Ge-based optical systems.

Magnetron Sputter Deposition of Amorphous Silicon–SiO2 Quantized Nanolaminates

Quantization effects in nanolaminate structures of oxide materials are proposed and experimentally demonstrated only recently. Herein, the material combination of amorphous silicon and SiO2 deposited by magnetron sputtering is investigated and it is shown that the quantization effect can be observed indeed. Transmission electron microscopy characterization gives evidence of continuous layers of amorphous silicon and SiO2 with well‐defined interfaces. The deposition process is described and the tunability of the refractive index and the bandgap energy is demonstrated. By doing so, the advantages of this novel material over classical optical materials are shown and feasibility is proved. As an example, a longpass optical interference filter with edge at 720 nm is deposited using quantized nanolaminates as the high and SiO2 as the low refractive index material. This filter can be deposited successfully with close match to the design. It shows a blocking range throughout the visible spectrum whereas a comparable filter based on SiO2–TiO2 only blocks 500–700 nm.

16 × 112 Gbps directly modulated membrane laser array for co-packaged interconnects

A low-cost and low-power-consumption optical transmitter with a narrow shoreline is crucial for short-reach optical communication. To increase the shoreline bandwidth density (Gbps/mm) at low cost, multiple optical components, including lasers, should be integrated on a single chip. In this study, we develop a sixteen-channel membrane laser array integrated with silica-based spot-size convertors on a SiO2/Si substrate, with a footprint of 1.11 × 2.75 mm2. A thin (340 nm) membrane buried-heterostructure sandwiched between low-index silica-based materials provides high carrier and optical confinement, which contributes to reducing power consumption. We demonstrated direct modulation with 28- and 56-GBaud PAM4 signals and verified that 2-km data transmission is feasible for all sixteen channels.

Effect of YF3 Coating Process on Film Stress

YF3 rare-earth fluoride coating material has received wide attention as an alternative to ThF4 low refractive index material, but the film layer can be seriously affected due to the different coating processes. Therefore, to investigate the rules between the coating processes of YF3 rare-earth fluoride coating materials, YF3 thin films were coated with different deposition rates and substrate temperatures. The stresses of YF3 thin films under different processes were obtained by a thin film stress meter, and the microscopic morphology of the thin films was characterized by atomic force microscopy. The results show that: YF3 monolayer film is tensile stress; in the deposition rate between 0.5nm/s~1.5nm/s, with the increase of the coating deposition rate YF3 monolayer film stress tends to decrease, the roughness of the film is also gradually increased, and the overall thickness of the film surface decreases; in the substrate temperature is greater than 50 ℃, the film stress is significantly reduced.

Wavelength Scale Singlet Achromatic Microlenses Based on High Refractive Index Materials

AbstractThe common methods used for correcting chromatic aberration are typically based on multi‐lens and multi‐material systems, resulting in lens thicknesses that are several orders of magnitude greater than the wavelength and complex combination designs. A method to achieve the singlet achromatic microlens of the wavelength‐scale thickness by utilizing high refractive index materials with an aspherical profile is proposed. A theoretical model based on the dispersion effect is developed to guide the selection of materials and the design of thicknesses for achieving chromatic aberration correction in singlet microlenses of a given diameter and numerical aperture. H‐ZLaF68N (68N) glass, sapphire, and fused silica with relatively high to low refractive index are selected to prepare the singlet achromatic microlenses to verify the validity of the model. The thicknesses of three microlenses are 573, 737 nm, and 1.27 µm, respectively, and all of them have achieved achromatic correction as designed. This indicates that the high refractive index material not only achieves achromatic aberration but also reduces the thickness by ≈50% compared with the conventional low refractive index material of silica glass. The presented wavelength‐scale singlet achromatic microlens hold significant promise for compact wearable devices, dynamic holography, and color projection displays.

Low reflective index, highly transparent, and ultra-low dielectric constant materials prepared via effective copolymerization of 4-methyl-1-pentene and a Si-containing α,ω-diolefin

A series of ultra-low dielectric constant materials containing C–Si-cyclic units were prepared. The new copolymers showed stable and ultra-low dielectric constants below 2.0, tunable glass transition temperature and mechanical performance.

Optical bistability in topological layered structure and its application in photonic neural network

Optical bistable state exhibits its great potential applications in photonic integrated circuit and photonic neural network. However, the traditional optical bistable state will be influenced by the system disorders, which are not suitable for application. In this work, we investigate the topological bistable states in a layered structure with center inversion symmetry consisting of alternating layers of high index material TiO<sub>2</sub> and low index material SiO<sub>2</sub>. In the topological mode, the electric field is highly localized in the inversion center of the layered structure (also known as the interface) and exponentially decays into the bulk. Thus, when the nonlinear permittivity is strategically introduced into those layers, nonlinear phenomena such as the bistable state appears. The finite element numerical simulations reveal that the optimal bistable state appears when the layer period is 5 with a threshold power around 1.2 W/m. Benefiting from the topological characteristics, such a bistable state persists when random perturbations are introduced into the layer thickness and refractive index. Finally, we apply the bistable states to a photonic neural network. The bistable function shows prediction accuracy similar to the classic activation function ReLu and sigmoid in various learning tasks. These results provide a novel method for inserting highly robust optical bistable states from topological layered structure into photonic neural network.

Improved Light Extraction in Organic Light‐Emitting Diodes via Semiconductor Dilution

AbstractIncreasing the internal light extraction efficiency of organic light‐emitting diodes (OLEDs) is key to improving their performance for solid‐state lighting applications; however, it is challenging to do this in a way that is compatible with high volume manufacturing. Here, it is shown that the outcoupling efficiency of OLEDs can be improved by diluting their hole transport layer (HTL) with the low refractive index material trifluoropropyl oligomeric silsesquioxane (F‐POSS). Specifically, co‐evaporating 40 vol.% F‐POSS in the HTL of single and multi‐stack phosphorescent OLEDs decreases its refractive index by Δn ≈ 0.2, which in turn yields a ≈12% increase in their outcoupling efficiency with no impact on electrical performance or operational lifetime. This result is significant because F‐POSS is a small molecule that sublimes cleanly, does not aggregate, and is compatible with state‐of‐the‐art HTL materials, making it a realistic path to increase light extraction in commercial OLEDs manufactured on existing production lines.

Ultra-high-Q and ultra-sensitive refractive index sensing in low refractive index dielectric gratings based on bound states in the continuum

The realization of a high quality factor (Q-factor) and strong local optical fields has long been of great interest in the field of nanophotonics. Unfortunately, it is still challenging to achieve high-Q and strong localized fields in nanostructures made of low refractive index materials. In this study, drawing upon the concept of bound states in the continuum (BICs), an asymmetric dielectric grating composed of low refractive index materials is demonstrated to generate an ultra-high-Q symmetry-protected quasi-BIC in the visible wavelength. Importantly, the design of BIC (quasi-BIC) mode enables the strong localized confinement of light in air. By leveraging this property, we realize ultra-sensitive refractive index sensing with a remarkable sensitivity of 669 nm/RIU and a high figure of merit (FOM) of 45,314RIU−1. This study offers an approach to achieve highly sensitive and high precision refractive index sensing with potential applications in the practical realization of strong light–matter interactions using low index materials.

Precise control of the optical refractive index in nanolattices

Recent developments in photonic devices, light field display, and wearable electronics have resulted from a competitive development toward new technologies to improve the user experience in the field of optics. These advances can be attributed to the rise of nanophotonics and meta-surfaces, which can be designed to manipulate light more efficiently. In these elements the performance scales are favorable to the index contrast, making the use of low-index material important. In this research, we examine the precise control of refractive indices of a low-index nanolattice material. This approach employs three-dimensional (3D) lithography and atomic layer deposition (ALD), allowing for precise control of the nanolattice geometry and its refractive index. The refractive indices of the fabricated nanolattices are characterized using spectroscopic ellipsometry and agree well with models based on effective medium theory. By controlling the unit-cell geometry by the exposure conditions and the shell thickness by the ALD process, the effective index of the nanolattice film can be precisely controlled to as low as 5 × 10−4. The proposed index control technique opens a gamut of opportunities and enables better performance in nanophotonic elements used in displays and other integrated devices.

Research on the Absorption Performance of Silicon-Based Pyramidal Microstructure with Ultra-Low Reflectivity

Anti-reflective structure can effectively suppress the light reflection on the surface of the object, thereby increasing the absorption of light, it has a wide range of applications in photovoltaics, such as optical sensors and photodetectors. Due to the limitation of low refractive index materials, it is difficult for existing anti-reflective coatings to achieve the expected low reflectance effect. Based on Maxwell’s electromagnetic wave theory, this paper uses Finite-Difference Time-Domain (FDTD)-solutions software to research the reflection spectrum of silicon-based pyramidal microstructure in the wavelength range of 200–1400nm, explores the influence of the height (H) and bottom side length (L) of the pyramidal on its reflection spectrum, and studies the changes of its electromagnetic field. On this basis, the absorption performance of the silicon-based pyramidal microstructure is further studied, and it is found that the absorption efficiency of silicon-based pyramidal microstructure for ultraviolet light reaches almost 100%, which provides important significance for its application in optical sensors and photodetectors.

Finite-element modeling of a perovskite-based symmetric plasmonic waveguide with deep-subwavelength confinement and high figure of merit

The two-dimensional perovskites are emerging as an excellent material platform for various optoelectronic devices such as solar cells, lasers, and photodetectors. Here, by combining perovskite materials and plasmonic materials, a hybrid plasmonic waveguide with perovskite layers serving as the low index materials is proposed. The modal characteristics, fabrication error tolerance, and integration performance of this structure are studied by using the finite element method at the wavelength of 1550 nm. The results show that the proposed waveguide exhibits the strong field confinement ability and high figure of merit. Moreover, the proposed waveguide shows a relatively high tolerance to fabrication errors, and exhibits an extremely low crosstalk, which is quite suitable for applications in the compact photonic integration.

Fano Resonances in Metal Gratings with Sub-Wavelength Slits on High Refractive Index Silicon.

The enhancement of optical waves through perforated plates has received particular attention over the past two decades. This phenomenon can occur due to two distinct and independent mechanisms, namely, nanoscale enhanced optical transmission and micron-scale Fabry-Perot resonance. The aim of the present paper is to shed light on the coupling potential between two neighboring slots filled with two different materials with contrasting physical properties (air and silicon, for example). Using theoretical predictions and numerical simulations, we highlight the role of each constituent material; the low-index material (air) acts as a continuum, while the higher-index material (silicon) exhibits discrete states. This combination gives rise to the so-called Fano resonance, well known since the early 1960s. In particular, it has been demonstrated that optimized geometrical parameters can create sustainable and robust band gaps at will, which provides the scientific community with a further genuine alternative to control optical waves.

All-dielectric scale invariant waveguide

Total internal reflection (TIR) governs the guiding mechanisms of almost all dielectric waveguides and therefore constrains most of the light in the material with the highest refractive index. The few options available to access the properties of lower-index materials include designs that are either lossy, periodic, exhibit limited optical bandwidth or are restricted to subwavelength modal volumes. Here, we propose and demonstrate a guiding mechanism that leverages symmetry in multilayer dielectric waveguides as well as evanescent fields to strongly confine light in low-index materials. The proposed waveguide structures exhibit unusual light properties, such as uniform field distribution with a non-Gaussian spatial profile and scale invariance of the optical mode. This guiding mechanism is general and can be further extended to various optical structures, employed for different polarizations, and in different spectral regions. Therefore, our results can have huge implications for integrated photonics and related technologies.

All-dielectric terahertz wave metagrating lens based on 3D printing low refractive index material

A metagrating lens with a high numerical aperture (NA = 0.9) is designed based on the grating diffraction principle and the unit structure of the asymmetric scattering mode. The metagrating lens is composed of all-dielectric material with low refractive index and achieves good focusing at an operating frequency of 0.1 THz. In our experiments, we used 3D printing technology to fabricate the metagrating lens to further reduce the fabrication cost of the metalens and avoid the disadvantages of conventional optical devices that are large and costly.

Topological invariance in whiteness optimisation

Maximizing the scattering of visible light within disordered nano-structured materials is essential for commercial applications such as brighteners, while also testing our fundamental understanding of light-matter interactions. The progress in the research field has been hindered by the lack of understanding how different structural features contribute to the scattering properties. Here we undertake a systematic investigation of light scattering in correlated disordered structures. We demonstrate that the scattering efficiency of disordered systems is mainly determined by topologically invariant features, such as the filling fraction and correlation length, and residual variations are largely accounted by the surface-averaged mean curvature of the systems. Optimal scattering efficiency can thus be obtained from a broad range of disordered structures, especially when structural anisotropy is included as a parameter. These results suggest that any disordered system can be optimised for whiteness and give comparable performance, which has far-reaching consequences for the industrial use of low-index materials for optical scattering.

First-principles calculations to investigate the dielectric and optical anisotropy in two-dimensional monolayer calcium and magnesium difluorides in the vacuum ultraviolet

Anisotropic dielectric and optical properties of two-dimensional (2D) calcium and magnesium difluorides were investigated in the vacuum ultraviolet (VUV) region of the electromagnetic spectrum (EM) using the first principles density functional theory (DFT). The anisotropy between the in-plane and out-of-plane directions shows that these materials are uniaxial, exhibiting optical and dielectric anisotropy. The optical functions of these anisotropic materials-optical absorption, photoconductivity, refractive index, reflection and extinction coefficients, and electron energy loss (EEL) spectra-are calculated in the framework of DFT. The low refractive index values and relatively small extinction coefficient make these materials alternative low-index 2D materials for the long wavelengths in the VUV region of the EM spectrum. The reflection and transmission spectra indicate the antireflective property of these materials. The calculated EEL function shows less energy loss of fast-traveling electrons in the material's medium. The maxima in the EEL spectrum are the main feature of plasma oscillations. The dissipation in the incident light radiation energy propagating through the dielectric medium is estimated with the dielectric loss tangent (tanδ). The magnesium difluoride is identified as a less dielectric loss medium than calcium difluoride in the VUV region. The present results suggest that these 2D materials are promising in low refractive index, high reflective, and antireflective coating materials in optoelectronic device applications. Also, electronic studies revealed that these are excellent materials for gate insulators in field-effect transistors based on 2D electronic materials.

The Influence of Nonlocal Metal-Dielectric Environments on Physical and Chemical Processes.

ConspectusPlasmonic nanolayers and laminar metallic/dielectric multilayers were originally developed for optical cloaking applications and lensing applications that could potentially image objects whose size was below the diffraction limit. These assemblies were initially formed from gold or silver nanorods grown within an alumina mesh. However, more recently, assemblies with similar properties have also been prepared by sequential thin-layer deposition of alternating layers of gold and magnesium fluoride (MgF2). These metal/dielectric composite materials enable control of the dielectric constant in the directions perpendicular to the layers and balance the real and imaginary dielectric constants of the assembly such that the speed and the amplitude of the waves traveling through the assembly are not attenuated.In this Account, we will also focus on a few of the applications ranging from surface wetting to fluorescence quenching to enhancement of photochemical reactions. First, we will share an introduction to processes used to create these materials, which are combinations of low refractive index metals and transparent higher index materials arranged in a scalable repeating fashion. Two fabrication methods were employed: an electrochemical deposition of Ag nanorods into an anodized alumina matrix which produced materials with an anisotropic negative refractive index material within the plane of the film and lamellar metal/dielectric layers in which the negative index perpendicular to the growth direction. These alternating layers of plasmonic metals and dielectric materials were ultimately chosen to prepare films for further testing, because of their relative ease of fabrication. We will continue with a discussion of a few of the applications of both of these nonlocal dielectric composite materials including more specialized plasmonic, composite, and hyperbolic metamaterials including fluorescence quenching, photochemical reactions, and surface wetting. In each of these applications, the unique response caused by the enhancement of the electric field and the interface between hyperbolic materials and plasmonic materials as they interact photophysically with their near neighbors is presented. In each of the applications, the enhanced electric field extends from the composite substrate layer to interact with its near neighbors and beyond. The presence of this extended interaction can be observed in the form of decreased emission lifetime, enhancement of photochemical reaction rates, and changes in the surface energies measured by contact angle goniometry. In this Account, all of these situations will be addressed. Finally, we will conclude with a summary and vision for the future as well as a discussion of the unique challenges and opportunities available as research active faculty at an HBCU.

Elevating performance of AlOxFy anti-reflection coating via controllable HF vapor fluorination

The introduction of anti-reflective coatings (ARCs) to optical devices has provided a simple and effective solution to improve their power efficiency. Among the various methods of preparing ARCs, the solution process is widely applied due to its simplicity, scalability, and naturally formable pores embedded in the film, which effectively reduce the refractive index of the material. Additionally, since low refractive index materials are always preferred for an effective ARC, strategies of fluorine substitution have been considered. Herein, we successfully introduce fluorine into Al2O3 ARCs by controlled HF vapor through abundant pores in the film. The exposure and reaction conditions were finely tunable, resulting in a precisely controlled amount of fluorine in the AlOxFy ARC. Finally, the gaseous HF vapor fluorination resulted in an effective porous ARC on a sapphire window by matching the refractive index between the surrounding media; thus, fluorinated ARC improves transparency. The maximum and the average transmittances of the ARC-applied window reach ∼99.15% and ∼97.04%, respectively. The suggested fluorination method is anticipated to have broad applicability for situations where surface chemistry modification is necessary. Highly reliable and controllable, this strategy can be used with complicated architectures without causing structural damage.